June 27th, 2016

AMP Induction Annealing Machine Review by Bill Gravatt

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

Annealing Made Perfect (AMP) Annealing Machine Review

Review by Bill Gravatt
Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product TestI had been following the progress of Alex and Matt Findlay with Annealing Made Perfect for almost three years as they pursued making the best annealing product for the private reloading market. The short explanation of why we anneal brass is to return the brass to a softer and consistent hardness after the brass has work-hardened from repetitive firing and sizing. As the President/co-owner of Sinclair International for over 21 years I saw a lot of products come through our doors that annealed brass but these products always seemed like they had very little supportive data and research behind them. Most of them were based on some type of torch system. The New Zealand-based father/son team of Alex and Matt spent these past three years addressing the challenging questions about annealing:

- What is the correct temperature to reach when annealing?
– How long should you take to get to that temp and how long should you remain there?
– How frequently should you anneal?
– Can you ruin your expensive brass?
– How do we make the process repeatable for the handloader?
– How do you accurately measure the case hardness?

They worked closely with the Electrical Engineering Department at the local University of Technology and invested a lot of capital into detailed metallurgical research. Their decision to use induction heating was because of its repeatability and the ability to reach exacting and consistent temperatures. Induction annealing is achieved by placing the cartridge in a magnetic field thereby inducing eddy currents within the brass and heating the brass without contacting the brass physically. To learn more, I suggest you visit the AmpAnnealing.com website. It is very informative.

Why should you anneal? If you are just a casual reloader, than annealing isn’t necessary but if you a serious wildcatter or competitive shooter you may want to consider it. More and more competitive shooters anneal their cases (not necessarily for adding life to the cases) to achieve more consistent pressures and velocities.

My first favorable impression was received by just opening the extremely well-packed shipping box. You could tell these guys take a great deal of pride in their product. The unit comes with three cartridge-specific pilots (you decide on which pilots), a shellholder collet, a power cord, a thorough, well-written, easy to follow instruction manual, and a USB cord for future software updates.

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

This machine is so easy to use that I was up and running within a few minutes. All I had to supply was the shells, the correct shell-holder and an aluminum pan to drop the hot cases into. I started annealing some unturned .308 Winchester cases (Lapua headstamp) that had four firings. First I screwed the pilot for .308 cases (#11) into the machine, placed my .308 shellholder into the supplied shellholder/collet and turned the power on. The display fired up right away and soon registered the program level that the machine was set to.

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

Since the machine uses induction heating, you need to set the heating level for the correct setting for the brass you are using. The alloy being used isn’t as important as the thickness or amount of brass in the neck and shoulder region. For example, Lapua and Norma have more brass in that area so the setting would be higher for these brands than Winchester brass. Also, if you have neck-turned brass, the setting would be reduced from the standard setting because there would be less mass in the air gap.

This manufacturer-produced video shows how the AMP annealing machine operates:

The settings are obtained by referring to the “Settings” section on the AMP website and are broken out by cartridge, brand, standard unturned cases, and then neck-turned cases with various amounts of wall thickness removed. A great service that AMP provides to the handloader is that you can send sample cases of your brass to them (U.S. location in Wolcott, Indiana) and they will test the hardness for you and send you the exact setting for your specific lot of brass.

My setting for unturned Lapua .308 Winchester brass was “92”. The buttons on the front of the machine allow you to adjust the setting quickly. After you set the program number, the setting is locked in after the first use until you change it again. I placed the first case in the shellholder, lowered the assembly down through the pilot and into position. I then hit the start button which illuminated immediately and then about 6 to 7 seconds later, the light went off signaling that heating was completed.

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

Now, be aware, these cases are extremely hot. I lifted the case out using the shellholder/collet and then dropped it into my aluminum pan. I then placed another case into the holder, put it into the machine and then repeated the process. Once I got the coordination down, I did 100 .308 Win cases in about 24 minutes. I did some 6mmBR cases later (Lapua) and annealed 100 cases in about 15 minutes at the “75” setting. I found myself raising my shop stool a little higher than normal so I was at a comfortable height in relationship to the top of the machine. Very easy to do — I actually had a student do a few cases with me and she had no problem at all following the instructions.

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

Annealing Made Perfect New Zealand Anneal Annealer Induction Review Pilot Findlay Bill Gravatt Gear Review Product Test

There is a thermal cut-off that prevents the machine from overheating. Depending on the setting, this can occur after 20 to 35 minutes of continuous use. When this has occurred, simply leave the machine on and the fans will cool it down so you can resume annealing. This isn’t surprising considering the amount of heat being generated.

All in all, I found this machine extremely easy to setup and operate. Now, does it work? I have test batches of brass that I am going to run over the chronograph in 10-round strings. I plan on running at least 10 strings of annealed brass and 10 strings of unannealed brass out of the same lot, same number of reloadings/firings and out of the same gun. I plan on alternating annealed strings and unannealed strings with a cooling off period every 20 rounds. When I do testing, I have my wife pre-label my batches as Batch A and B so I won’t know what rounds I am shooting until I get back from the range. I’ll make the results available as soon as I can. My expectation is that velocities will be more consistent based on my understanding of the lab results that the Findlays have achieved with their Annealing Made Perfect machine. For more information, visit their website at AmpAnnealing.com.

Similar Posts:

Tags: , , , , , ,