Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









August 29th, 2019

How to Sight-In Your Hunting Rifle in Four Shots

hunting zero zeroing sight-in easy NSSF boresighting
Photo courtesy Vortex Optics.

Hunting season is right around the corner. We know many readers have acquired a new hunting rifles, or perhaps are using new ammo or a new optic. If you’ve got new gear, you’ll want to zero your hunting rig properly. Here’s how…

Here’s a simple procedure that lets you get a solid zero in just four shots. Of course you probably want to fire a few more rounds to confirm your zero before you head off to your hunting grounds, but this will let you get on-target with a minimum amount of time and ammo expended. (This assumes your scope is securely mounted, and the bases are not drastically out of alignment.)

QUICK-TIP: The Key to this procedure is Dialing to Shot One Point of Impact (POI). Re-aim at center of target after SHOT ONE. Then with the rifle motionless, use the turrets to put the middle of the cross-hair on the first shot location.

1. First, remove the bolt and boresight the rifle. Adjust the position of the rifle so that, looking through the bore, you can see the center of the target with your eyes. Secure the rifle in the rests to maintain its position as boresighted. Then, without moving the rifle, center the reticle. That should get you on paper. With the rifle solidly secured in front and rear rests or sandbags, aim at the center of a target placed at your zeroing distance (50 or 100 yards). Confirm there are no obstructions in the barrel! Then load and fire SHOT ONE. Then, return the gun to the exact position it was when you pulled the trigger, with the cross-hair centered on the target as before.

2. Locate, in the scope, where your first bullet landed on the target. Now, while you grip the rifle firmly so it doesn’t move, have a friend adjust the turrets on your scope. While you look through the scope, have your friend turn the windage and elevation turrets until the cross-hairs, as viewed through the scope, bisect the first bullet hole on the target. Use the turrets to move the center of the reticle to the actual position of shot number one. IMPORTANT: Dial the crosshairs to the hole — don’t move the rifle.

Watch NSSF Zeroing Video showing method of moving reticle to Shot 1 Point of Impact.

3. After you’ve adjusted the turrets, now re-aim the rifle so the cross-hairs are, once again, positioned on the target center. Keep the rifle firmly supported by your rest or sandbag. Take the SECOND SHOT. You should find that the bullet now strikes in the center of the target.

3-Shot Zero

4. Take a THIRD SHOT with the cross-hairs aligned in the center of the target to confirm your zero. Make minor modifications to the windage and elevation as necessary.

5. Finally, shoot the rifle from a field rest (shooting sticks, bipod, or rucksack) as you would use when actually hunting. Confirm, with SHOT FOUR, that your zero is unchanged. You may need to make slight adjustments. Some rifles, particularly those with flexy fore-arms, exhibit a different POI (point of impact) when fired from a bipod or ruck vs. a sandbag rest.

This Video Shows the Process Described Above:

Fouling Shots and Cold Bore Condition
If you recently cleaned your rifle, you may want to fire two or three fouling shots before you start this procedure. But keep in mind that you want to duplicate the typical cold bore conditions that you’ll experience during the hunt. If you set your zero after three fouling shots, then make sure the bore is in a similar condition when you actually go out hunting.

Permalink Bullets, Brass, Ammo, Hunting/Varminting, Tech Tip No Comments »
August 29th, 2019

Great Deal on Vortex Fury HD LRF300 Rangefinding Binoculars

Vortex Fury binoculars LRF Laser Rangefinder rangefinding binocs

Generation One Vortex Fury HD LRF300 10×42 laser rangefinder binoculars are on sale at a HUGE discount. These once sold for $1199.00. Now, with the introduction of the Gen Two Vortex Fury HD 5000 LRF binocs, the Gen One units are just $799.00 at EuroOptic.com. Save a full $400 with a unit that can range to 1600 yards and has excellent optics. If you need even more ranging capability (not likely for a typical hunt), Vortex’s Gen Two Fury HD 5000 model is available for $1199.00 on Amazon. The choice is up to you. We think most hunters will be more than happy with the $799.00 Gen One unit. The $400 you save can buy a quality scope for your hunting rifle.

Vortex Fury binoculars LRF Laser Rangefinder rangefinding binocs

The Vortex Fury has some very cool features. It offers angle compensation as well as line-of-site modes. Scan mode gives readings as you pan or track a moving animal. You can set the distance output to yards or meters. All the controls are on the right side so you can operate the Fury HD easily with one hand.

Here are two video reviews of Gen One Vortex Fury Laser RangeFinder (LRF) Binoculars:

Review Summary: This is more an infomercial than a field test, but the video does a very good job showing the features of the Gen One 10×42 Vortex Fury HD LRF300. In addition, the reviewer explains how hunters can best use the Vortex Fury LRF binoculars in the field.

Review Summary: This unboxing video covers the operation and controls of the Gen One Vortex Fury HD LRF300 rangefinding binoculars.

Why Use Rangefinding Binoculars?
With rangefinding binoculars, you can carry one less piece of gear, and a binocular optic is much more effective in the field than the monocular on a typical dedicated laser rangefinder (LRF). The stereo view gives better definition and depth perception, and the larger, binocular lenses give better low-light performance than the smaller-diameter monocular optic found in a conventional LRF.

Permalink - Videos, Gear Review, Optics No Comments »