August 1st, 2020

The Hazards of Old Ammo — Watch Out for Internal Corrosion!

300 Winchester Magnum winmag reloading hand-loading powder corrosion
Above is a 26-year-old hand-loaded .300 Winchester Magnum case that failed to fire. After the misfire, the shooter used an inertial (impact) bullet puller to pull the bullet. In the process the case-neck sheared off.

Here’s a cautionary tale from the Tactical Rifle Shooters Facebook group. This real-world example explains why you should be cautious of old ammunition. Here serious internal corrosion was discovered.

Old Ammunition — Why You Should Be Careful

Commentary by Tactical Rifle Shooters
The subject often comes up as to whether it is safe to shoot old ammunition. Historically my answer has always been yes, since over the years I have shot military surplus ammo dating back to World War II (1939-1945) and never had a problem. With over 40 years in competitive shooting, I’ve also had boxes of factory ammo that were 30+ years old and all worked flawlessly.

But I had an interesting experience this week shooting some .300 Winchester Magnum (WinMag) that I had loaded for competition with Reloder 22 back in 1993. I was breaking in a new barrel so just shooting any old ammo that I had. Of the 20 rounds, 15 shot perfectly, three had a fraction of a second hang-fire, and two didn’t shoot at all.

SMART TIP: If you have old ammunition, pull one bullet to see what’s going on inside.

So I pulled the bullets using a hammer-type impact (inertial) bullet puller. What I found was verdigris-like corrosion inside the necks, with one neck completely separating. One reason for this could be that dissimilar metals (copper and brass) can set up a reaction resulting in corrosion. Like I said, this is the first time I’ve seen this, but will definitely be more aware when shooting old hand-loads in the future.

300 Winchester Magnum winmag reloading hand-loading powder corrosion

Above is one of the 26-year-old reloaded .300 WinMag cartridges which had failed to fire. To check the internal condition, the bullet was removed using an impact (inertial) bullet puller. Note the verdigris-like corrosion and crack in neck.

300 Winchester Magnum winmag reloading hand-loading powder corrosion

Here’s a close-up of the same .300 Winchester Magnum hand-load from 1993 showing serious corrosion inside the neck. (This was a fail-to-fire.) The powder was Alliant Reloder 22. If you have old ammo, it wouldn’t hurt to pull one bullet to see what’s going on inside.

CREDIT Tactical Rifle Shooters Facebook Group for this Ammo Tech Tip and photos.

Permalink Bullets, Brass, Ammo, Gunsmithing, Reloading, Tech Tip 1 Comment »
May 31st, 2015

.300 WM Aussie Style — Most Popular 1000-Yard Benchrest Video

Here’s a true “Blast from the Past”, a video featuring our friend Stuart Elliott of Brisbane, Australia. This 2011 video has now racked up nearly 680,000 views, making it probably the most-watched long-range benchrest video ever uploaded to YouTube. The video shows Stuart shooting a 10-shot Heavy Gun string at the Brisbane range, Queensland, Australia, in July 2011. In this example, Stuart elected to “run a condition” with his big, .300 WM Heavy Gun, shooting fast with slight hold-off adjustments as the wind increased during the string. The cartridge is a .300 Winchester Magnum, loaded with moly-coated 190gr Berger VLDs. Stuart has an unusual bolt configuration. After each shot, Stuart removes the bolt completely with his right hand, and then uses the bolt to “shuck” the fired cartridge while loading the new cartridge with his left hand. That sounds awkward, but Stuart makes it all look easy. Stuart runs BRT Shooters Supply, a leading vendor of precision shooting equipment (including March scopes), in Australia and nearby regions.

Stuart Elliot BRT Shooters 1000 yards 1k benchrest march scope

Permalink - Videos, Competition 7 Comments »