This site is for and about accurate shooters. So today we feature the short-range group Benchrest game, where it’s all about shooting tiny groups in the ones and even “zeros”. Seeing the tiny groups 6 PPC aces produce, it’s easy to think the precision is all about the equipment. But there is a lot more involved. A talented human still has to watch the flags, run the gun properly, and tune his loads for the conditions. Here are some tips from one of the world’s best benchresters, Charles Huckeba.
Texan Charles Huckeba was the top individual shooter at the 2013 World Benchrest Championships (WBC) held near Sydney Australia in October 2013. In this video, 2013 WBC Two-Gun Overall winner Charles shoots a 1/8th MOA group at 200 yards — “a little bitty dot” as a fellow Team USA shooter observes. That’s impressive. If you can describe Huckeba’s style in a nutshell it would be “smooth, consistent, and rapid but not hurried”.
Charles also employed some unusual hardware. In the video, take a close look at the joystick on the Farley Coaxial front rest. There’s no knob at the end. In its place is a small, wood ammo caddy. Charles removed the standard knob from the handle of his Farley rest and replaced it with a home-made wood block that holds cartridges for the record target. The 10.5-lb Light Varmint rifle is chambered in 6PPC with a BAT Machine Action and a composite wood and carbon-fiber stock.
Watch Charles Huckeba Shoot 1/8 MOA, 200-yard group at World Benchrest Championships
Here is the actual 200-yard, 5-shot group Charles shot in the video. Photo (by Stuart Elliot) taken through the lens of Huckeba’s 50X March scope (reticle has 1/16th MOA Dot).
Analyzing the Fine Points — What Makes Huckeba So Good
Short-range benchrest shooter Boyd Allen saw some interesting things in Huckeba’s WBC performance, as captured on video. Boyd noticed Huckeba’s smooth gun-handling and efficient loading. But Boyd also spied some interesting equipment, including an innovative joystick “handle-caddy”.
1. Low Friction Bags — When Huckeba slid his rifle, there was very little apparent friction. The front bag features the new 3M material (ScotchLite) on the sliding surfaces. The rear Protektor bag has ears of the same low-friction material.
2. Pause Before Chambering — While he was watching the flags and deciding when to start firing, Charles kept his first round in the action, but out of the barrel’s chamber, probably so as not to heat the cartridge and change the round’s point of impact.
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
4. Smooth-Cycling BAT Action — Note how smoothly Huckeba’s action operates. When Charles lifts the bolt handle (to extract a round and cock the firing pin), this does not disturb the rifle. Likewise, as he closes the bolt, the gun doesn’t wobble. The smooth action allows Charles to hold point of aim even when shooting relatively quickly. Huckeba’s BAT action is chrome-moly steel. Some shooters believe this metal makes for a smoother action than stainless steel or aluminum.
5. Long-Wheelbase Stock — The wood and carbon fiber stock is light, long, and stiff. Yet, importantly, the stock is also well-damped. The longer-than-average stock length (with extended forearm) seems to help the gun track well without jumping or rocking. The longer forearm allows a longer “wheelbase”, effectively shifting the weight distribution rearward (less weight on the front, more weight on the rear). This places a greater share of the gun’s weight on the rear bag, as compared to a more conventional benchrest stock. Huckeba’s stock, built by Bob Scoville, is at the cutting edge of short-range benchrest design. Its light-weight balsa wood and carbon fiber construction provides a combination of stiffness and vibration damping that allows its relatively long fore-end to be fully utilized to increase the weight on the rear bag (always an issue with 10.5-pound rifles).
To learn more about this benchrest stock design, read the comments by stock-builder Bob Scoville in our PPC with Pedigree story in our Gun of the Week Archives. Bob observed:
“There is a lot more to the structure of the stocks than meets the eye. The carbon fiber skin with which I cover the stocks creates a light, tough exterior surface. However, this contributes very little to the overall performance of the stocks. The real strength and stiffness is the result of an internal beam utilizing balsa core/carbon fiber technology.
This type construction can be found in aircraft, race cars, powerboats, and sailboats. It is interesting to note, balsa has the highest strength to weight ratio of all woods and carbon fiber is one of the lowest stretch (modulus of elasticity) relative to weight of all materials. The marriage of these two materials is common in the high-performance world. Additionally, balsa is used commercially for vibration dampening and sound reduction.”
Video find by Boyd Allen. Video by Stuart Elliot of BRT Shooters Supply, Brisbane, Australia.
Share the post "Shoot Like a Champion — How to Drill Tiny Groups at 200 Yards"
After being held at the Kelbly’s Range in Ohio for decades, the Super Shoot, the top-tier short-range benchrest score competition, will be held May 22-25, 2023 at the Bench Rest Rifle Club in Missouri. This is a great location, much favored by elite benchrest shooters. This excellent range was the host of the 2022 NBRSA Nationals (photo above).
This will be Super Shoot 49. Historically, the Super Shoot has been the largest 100/200-yard Benchrest match in the world. This year the Super Shoot will be held at one of the premier benchrest facilities in the USA, the Bench Rest Rifle Club of St. Louis situated in Wright City, just northwest of St. Louis.
To shoot in the big match, it’s best to first register as a member of the SuperShootSports.com website. Membership is free. By becoming a member you will have access to online registration for the 49th Super Shoot and other features as they become available. There is no charge to join as a site member but there ARE fees to compete in the actual 2023 Super Shoot. So no payment is required initially to register on the site, but competition fees will be required at a later date. Match Sponsors include Shilen Rifles and Hottenstein Bullets.
The Bench Rest Rifle Club of St. Louis hosted the 2015 World Benchrest Championships:
The St. Louis shooting range facility is excellent. Forum member Alex M. posted: “The St. Louis Bench Rest Rifle Club is the finest shooting facility I have seen. The various rifle, pistol, shotgun, and archery ranges are great. They have a nice official trap field, together with manually operated traps. I shoot pistol and rifle with my wife at 25 to 600 yards. They have a very nice dedicated rimfire range, and training bays. I shoot their monthly F-Class matches (600 yards) where they award medals (1st, 2nd, 3rd) for F-Open, F-T/R and F-Bench. They also host the very popular Sierra Cup Challenge.”
Map to Bench Rest Rifle Club Range in Wright City, Missouri.
2022 Super Shoot — Last One at the Kelbly’s Range
The last Benchrest Super Shoot at the Kelbly’s Range was held May 24-27, 2022. This was the “final showdown” of the world’s group-shooting benchrest aces at the Kelbly’s range facility in Ohio. The overall 2022 Super Shoot Champion, with best combined 100 and 200-yard group-size Two Gun Aggregates (Aggs), was Jeff Summers. Gun writer James Mock noted: “The master of the Super Shoot, Jeff Summers, did it again. He fought the tough conditions and came out on top of the 200+ shooters at the final Kelbly-held Super Shoot. [That is] four times that Jeff has finished first. This shows that good guys can do well. Second place went to Ohioan Don Powell.” Summers finished with a 0.2513 Agg.
Share the post "2023 Super Shoot Will Be Held May 22-25 in Missouri"
An notable era in modern benchrest history is ending. The last Benchrest Super Shoot at the Kelbly’s Range has concluded. Held May 24-27, 2022, this was the “final showdown” of the world’s group-shooting benchrest aces at the Kelbly’s range facility in Ohio. The overall 2022 Super Shoot Champion, with best combined 100 and 200-yard group-size Two Gun Aggregates (Aggs), was Jeff Summers. Gun writer James Mock noted: “The master of the Super Shoot, Jeff Summers, did it again. He fought the tough conditions and came out on top of the 200+ shooters at the final Kelbly-held Super Shoot. [That is] four times that Jeff has finished first. This shows that good guys can do well. Second place went to Ohioan Don Powell.” Summers finished with a 0.2513 Agg. Shown below are the combined 100/200 Two Gun Aggs for the top 21 finishers. SEE Forum Thread.
Over 200 competitors shot at the XLVIII Super Shoot event, considered the “Superbowl of Short-Range Benchrest”. The vast majority of competitors were shooting the 6 PPC cartridge with 6mm bullets under 70 grains. Another Super Shoot-type event may be held in the future in Texas, but this was the last event to be held at the impressive Kelbly’s Range in North Lawrence, Ohio.
This major event, held annually for many years, attracted hundreds of the world’s top short-range benchrest-for-group shooters. Over the years, at the Super Shoot, you would find the world’s best benchrest shooters on the long firing line, including Hall of Fame legends like Tony Boyer, Wayne Campbell, Lester Bruno, Alan Euber and other talented PPC pilots.
Conditions this year were sometimes tough, with brisk winds and rain. Here is a video from Forum member Jay Wallace, captured on Thursday May 26th. You can see the raindrops falling:
Rain Falls at 2022 Super Shoot at Kelbly’s Range in Ohio:
This year’s Super Shoot winner, Jeff Summers, was featured in the Daily Bulletin in 2012, when Jeff won the 40th Annual Super Shoot a decade ago. That article mentioned that Summers used a bag squeezing technique at that time. This shows that while many competitors use expensive joystick rests, bag squeezing (to aim the rifle) can still achieve great results. This shows that one can still be very competitive without having the most sophisticated rest or expensive new toys.
Super Shoot — What It’s All About
The excitement and anticipation leading up to a Super Shoot can be hard to explain to those who haven’t been to one. Every year, some shooters arrive at the Super Shoot a week early to dial in their rifles, learn wind conditions for the range, and enjoy the camaraderie of their fellow shooters. As the match draws closer, campers and RVs fill the area behind the range, and shooters stake out turf all over the property with their reloading and cleaning equipment setups.
Many shooters choose to load cartridges in the main barn directly behind the 60-bench firing line, while others decide to work in pop-ups, campers and other outbuildings around the facility. Benchrest shooters tend to load in small batches, and some most load cartridges between each match. Many shooters clean their rifles after each match, while others sometimes go two or three matches between cleanings, depending on the number of rounds they fire.
Another part of high-level benchrest competition that will amaze first-time attendees is the quality and amount of equipment benchrest shooters use. Just in front of the shooting benches and the targets, range flags of all kinds sprout up, from the typical “daisy wheel” flags to very sophisticated velocity indicators that show varying wind intensity. Shooters adjust their flags to align with the particular target in front of a specific bench, just slightly below the path of the bullet but still partially visible in the high-powered scopes.
The rifles represent a variety of actions, usually custom, with heavy benchrest barrels by various barrel makers. The most popular cartridge used is the 6mm PPC, but occasionally you will run into someone using a Grendel necked to 6mm or 6mmBR-based case. Rifle rests used are typically heavy tripods or plate rests. You see a lot of Sinclair rests, Farley rests, SEB Rests, and a variety of others, including a few homemade rests. Bags are typically Edgewood, Protektor, and now some Lenzis.
Super Shoot — Runners, Pickers and the Pursuit of Perfection
The techniques vary between shooters, and they are interesting to observe. Some shooters “run” their targets and will shoot a quick sighter and then run all 5 shots as fast as they can before conditions change. Others are “pickers” and shoot each shot carefully, going back and forth between the record target and the sighter target to verify wind conditions and bullet drift. These guys will sometimes shoot up to 10 sighters and use the full seven minutes. Both styles of shooting work and many shooters use both techniques depending on the match conditions[.]
Share the post "Super Shoot 2022 — Last One Ever at Kelbly’s Range in Ohio"
Today we feature the short-range group Benchrest game, where it’s all about shooting tiny groups in the ones and even “zeros”. Seeing the tiny groups 6 PPC aces produce, it’s easy to think that precision is all about the equipment. But there is a lot more involved. A talented human still has to watch the flags, run the gun properly, and tune his loads for the conditions. Here are some tips from one of the world’s best benchresters, Charles Huckeba.
If you were an aspiring basketball player, you’d surely study All-Stars such as Stephen Curry and Devin Booker to see how they shoot so well. This article provides a chance to see how a world-class benchrest All-Star drills tiny 5-shot groups at 100 and 200 yards.
Texan Charles Huckeba was the top individual shooter at the 2013 World Benchrest Championships (WBC) held near Sydney Australia in October 2013. In this video, 2013 WBC Two-Gun Overall winner Charles shoots a 1/8th MOA group at 200 yards — “a little bitty dot” as a fellow Team USA shooter observes. That’s impressive. If you can describe Huckeba’s style in a nutshell it would be “smooth, consistent, and rapid but not hurried”.
Charles also employed some unusual hardware. In the video, take a close look at the joystick on the Farley Coaxial front rest. There’s no knob at the end. In its place is a small, wood ammo caddy. Charles removed the standard knob from the handle of his Farley rest and replaced it with a home-made wood block that holds cartridges for the record target. The 10.5-lb Light Varmint rifle is chambered in 6PPC with a BAT Machine Action and a composite wood and carbon-fiber stock.
Watch Charles Huckeba Shoot 1/8 MOA, 200-yard group at World Benchrest Championships
Here is the actual 200-yard, 5-shot group Charles shot in the video. Photo (by Stuart Elliot) taken through the lens of Huckeba’s 50X March scope (reticle has 1/16th MOA Dot).
Analyzing the Fine Points — What Makes Huckeba So Good
Short-range benchrest shooter Boyd Allen saw some interesting things in Huckeba’s WBC performance, as captured on video. Boyd noticed Huckeba’s smooth gun-handling and efficient loading. But Boyd also spied some interesting equipment, including an innovative joystick “handle-caddy”.
1. Low Friction Bags — When Huckeba slid his rifle, there was very little apparent friction. The front bag features the new 3M material (ScotchLite) on the sliding surfaces. The rear Protektor bag has ears of the same low-friction material.
2. Pause Before Chambering — While he was watching the flags and deciding when to start firing, Charles kept his first round in the action, but out of the barrel’s chamber, probably so as not to heat the cartridge and change the round’s point of impact.
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
4. Smooth-Cycling BAT Action — Note how smoothly Huckeba’s action operates. When Charles lifts the bolt handle (to extract a round and cock the firing pin), this does not disturb the rifle. Likewise, as he closes the bolt, the gun doesn’t wobble. The smooth action allows Charles to hold point of aim even when shooting relatively quickly. Huckeba’s BAT action is chrome-moly steel. Some shooters believe this metal makes for a smoother action than stainless steel or aluminum.
5. Long-Wheelbase Stock — The wood and carbon fiber stock is light, long, and stiff. Yet, importantly, the stock is also well-damped. The longer-than-average stock length (with extended forearm) seems to help the gun track well without jumping or rocking. The longer forearm allows a longer “wheelbase”, effectively shifting the weight distribution rearward (less weight on the front, more weight on the rear). This places a greater share of the gun’s weight on the rear bag, as compared to a more conventional benchrest stock. Huckeba’s stock, built by Bob Scoville, is at the cutting edge of short-range benchrest design. Its light-weight balsa wood and carbon fiber construction provides a combination of stiffness and vibration damping that allows its relatively long fore-end to be fully utilized to increase the weight on the rear bag (always an issue with 10.5-pound rifles).
To learn more about this benchrest stock design, read the comments by stock-builder Bob Scoville in our PPC with Pedigree story in our Gun of the Week Archives. Bob observed:
“There is a lot more to the structure of the stocks than meets the eye. The carbon fiber skin with which I cover the stocks creates a light, tough exterior surface. However, this contributes very little to the overall performance of the stocks. The real strength and stiffness is the result of an internal beam utilizing balsa core/carbon fiber technology.
This type construction can be found in aircraft, race cars, powerboats, and sailboats. It is interesting to note, balsa has the highest strength to weight ratio of all woods and carbon fiber is one of the lowest stretch (modulus of elasticity) relative to weight of all materials. The marriage of these two materials is common in the high-performance world. Additionally, balsa is used commercially for vibration dampening and sound reduction.”
Video find by Boyd Allen. Video by Stuart Elliot of BRT Shooters Supply, Brisbane, Australia.
Share the post "Benchrest Shooting Technique — How to Shoot Like a Champion"
by James Mock
After owning three different rifles with BAT actions, I have become a loyal fan of BAT Machine quality and customer service. Back in 2009, I traded my BAT/Scoville for the BAT/Leonard that I currently shoot. This rifle has a long history and Terry Leonard told me that “Old 87″ (as I have named it) was one of the earlier BATs that he stocked. He wrapped the stock in fiberglass and used 2-part epoxy back then. I must say that this rifle has held up remarkably well since it dates back to the 1990s. The action is a RB/LP/RE octagon Model B with .308 bolt-face.
Rifle Has Multiple Barrels for Multiple Disciplines
With this gun, I have shot several barrels of different calibers (.22 PPC, .22 PPC-short .095, 6mm PPC, 6XC, 6mm Dasher, .30BR, and will soon have a 6 BR-AI). It has been an exceptionally accurate rifle in several disciplines. In the hands of previous owners, it earned several Hall-of-Fame (HOF) points, and a “middle-of-the-pack” shooter (me) even received a HOF point with this rifle.
For most of its life, Old 87 served as a short range benchrest rifle, but I have used it for the last few years as a 600-yard rifle with the 6mm Dasher barrel. I was lucky enough to earn the Shooter of the Year award at the Prince Memorial Range in Louisiana for 2016.
After shooting my two Dasher barrels for last eight years, I have noticed a drop-off in accuracy at 600 yards. A decision had to be made — get a new barrel or sell the rifle and retire from competition. I am in my late 70s and my competition days are limited due mainly to a chronic neck problem. After mulling over the decision to retire or not, I decided to give Old 87 one more year. Here is the story of how we upgraded the old war-horse.
Old 87 REBORN — Upgrading with New Components
I prefer cut-rifled barrels with four lands and grooves and have had success with .236 bore diameters and 1:8″ twist in long range rifles. I searched for barrels meeting those parameters and found a suitable BRUX at Bugholes.com (Southern Precision Rifles).
The 6BR-AI Option — Easy Fire Forming
I thought about having Billy Stevens chamber it for the Dasher, but decided to try something new. There seems to be a lot of interest in the 6BR-AI and I said, “Why not?” Well, I bought a shortened Dasher die from Harrell’s and will use my Wilson Dasher seating die. Bart Sauter was kind enough to let me use his reamer for chambering.
Fitting a New Roller-Type Cocking Piece on Older BAT Action
Since I was into the project this deep, I called Mike Ezell and ordered one of his Tungsten powder-dampened tuners. Since Old 87 had thousands of rounds since the firing pin spring has been replaced, I decided that it was probably needed. Well, I got to thinking (very dangerous) and asked Daryle Thom if it would be feasible to put a roller-type cocking piece and a new firing pin spring on such an old action.
The folks at BAT are very accommodating and they said that it would be no problem with such a conversion. While my bolt was in Idaho, the barrel with Ezell tuner arrived and I could not shoot it. However, my friend Jeff Turner loaned me his BAT bolt to see if it would work. Although the rifles differ in age by 15 or more years, the borrowed bolt worked perfectly in my rifle. This is a testimony to the great machine work performed at BAT Machine.
New Bolt Roller Tail-Piece Makes a Big Difference in Cocking Effort
With the borrowed bolt I managed to fire-form 50 rounds and get them ready for our 600-yard match on September 16. The folks at BAT quickly fixed my bolt by replacing the mainspring and ejector spring, polishing the ejector, and replacing the tail-piece with their roller type. Pictured below is this tail piece that makes a remarkable difference in the force needed to cock the action. It is amazing what this little wheel can do… even when placed in a 25+ year old action.
Working with the Ezell Barrel Tuner — Small Increments Work Best
Also, I would like to congratulate Mike Ezell on his new tuner which contains powdered Tungsten. It is easy to set up and Mike will help a buyer get maximum effectiveness from the unit. Just give him a call. Below is a picture of the tuner. I was lucky enough to have some time to “play” with it before the match.
Talking about the tuner, Mike writes: “Our new barrel tuners… PDT stands for particle dampening technology. The science is there, we just applied it to a barrel tuner. The advantages are a wider tune window and more efficient control of barrel harmonics…in a tuner design that actually looks good.”
Mike advised me to set the tuner by turning it all the way into the shoulder and then come out to zero or the second time zero comes up if there is not at least half of a turn between the shoulder and the first zero. It is best to start with a proven load and adjust the tuner from that load. As unlikely as it seems, a rifle can go from a good tune to a very poor tune with only 5 marks (.005”) and vice versa.
Mike cautions those who use his tuner to NOT make adjustments which are too large. As a matter of fact, he recommends adjustments of .001 inch at a time. Ezell’s tuners are screwed onto the barrel with .900” by 32 threads per inch and has 32 marks on the circumference of the tuner. Therefore, each mark moves the tuner in or out by .001 inch. There are three set screws with Teflon tips which provide friction for the tuner on the threads. Do not tighten the screws so tight as they damage the fine threads.
If you want the smoothest bolt possible for your BAT, call or e-mail Daryle or Bruce Thom at BAT Machine and discuss your needs with them. I am sure glad that I did. If you want a state-of-the-Art tuner for your barrel, give Mike Ezell a call or visit his Ezell Custom Rifles Facebook Page.
— Good shooting, James Mock
Share the post "6BR Ackley Revival for Benchrest Rifle from 1990s"
This site is for and about accurate shooters. So today we feature the short-range group Benchrest game, where it’s all about shooting tiny groups in the ones and even “zeros”. Seeing the tiny groups 6 PPC aces produce, it’s easy to think the precision is all about the equipment. But there is a lot more involved. A talented human still has to watch the flags, run the gun properly, and tune his loads for the conditions. Here are some tips from one of the world’s best benchresters, Charles Huckeba.
Texan Charles Huckeba was the top individual shooter at the 2013 World Benchrest Championships (WBC) held near Sydney Australia in October 2013. In this video, 2013 WBC Two-Gun Overall winner Charles shoots a 1/8th MOA group at 200 yards — “a little bitty dot” as a fellow Team USA shooter observes. That’s impressive. If you can describe Huckeba’s style in a nutshell it would be “smooth, consistent, and rapid but not hurried”.
Charles also employed some unusual hardware. In the video, take a close look at the joystick on the Farley Coaxial front rest. There’s no knob at the end. In its place is a small, wood ammo caddy. Charles removed the standard knob from the handle of his Farley rest and replaced it with a home-made wood block that holds cartridges for the record target. The 10.5-lb Light Varmint rifle is chambered in 6PPC with a BAT Machine Action and a composite wood and carbon-fiber stock.
Watch Charles Huckeba Shoot 1/8 MOA, 200-yard group at World Benchrest Championships
Here is the actual 200-yard, 5-shot group Charles shot in the video. Photo (by Stuart Elliot) taken through the lens of Huckeba’s 50X March scope (reticle has 1/16th MOA Dot).
Analyzing the Fine Points — What Makes Huckeba So Good
Short-range benchrest shooter Boyd Allen saw some interesting things in Huckeba’s WBC performance, as captured on video. Boyd noticed Huckeba’s smooth gun-handling and efficient loading. But Boyd also spied some interesting equipment, including an innovative joystick “handle-caddy”.
1. Low Friction Bags — When Huckeba slid his rifle, there was very little apparent friction. The front bag features the new 3M material (ScotchLite) on the sliding surfaces. The rear Protektor bag has ears of the same low-friction material.
2. Pause Before Chambering — While he was watching the flags and deciding when to start firing, Charles kept his first round in the action, but out of the barrel’s chamber, probably so as not to heat the cartridge and change the round’s point of impact.
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
4. Smooth-Cycling BAT Action — Note how smoothly Huckeba’s action operates. When Charles lifts the bolt handle (to extract a round and cock the firing pin), this does not disturb the rifle. Likewise, as he closes the bolt, the gun doesn’t wobble. The smooth action allows Charles to hold point of aim even when shooting relatively quickly. Huckeba’s BAT action is chrome-moly steel. Some shooters believe this metal makes for a smoother action than stainless steel or aluminum.
5. Long-Wheelbase Stock — The wood and carbon fiber stock is light, long, and stiff. Yet, importantly, the stock is also well-damped. The longer-than-average stock length (with extended forearm) seems to help the gun track well without jumping or rocking. The longer forearm allows a longer “wheelbase”, effectively shifting the weight distribution rearward (less weight on the front, more weight on the rear). This places a greater share of the gun’s weight on the rear bag, as compared to a more conventional benchrest stock. Huckeba’s stock, built by Bob Scoville, is at the cutting edge of short-range benchrest design. Its light-weight balsa wood and carbon fiber construction provides a combination of stiffness and vibration damping that allows its relatively long fore-end to be fully utilized to increase the weight on the rear bag (always an issue with 10.5-pound rifles).
To learn more about this benchrest stock design, read the comments by stock-builder Bob Scoville in our PPC with Pedigree story in our Gun of the Week Archives. Bob observed:
“There is a lot more to the structure of the stocks than meets the eye. The carbon fiber skin with which I cover the stocks creates a light, tough exterior surface. However, this contributes very little to the overall performance of the stocks. The real strength and stiffness is the result of an internal beam utilizing balsa core/carbon fiber technology.
This type construction can be found in aircraft, race cars, powerboats, and sailboats. It is interesting to note, balsa has the highest strength to weight ratio of all woods and carbon fiber is one of the lowest stretch (modulus of elasticity) relative to weight of all materials. The marriage of these two materials is common in the high-performance world. Additionally, balsa is used commercially for vibration dampening and sound reduction.”
Video find by Boyd Allen. Video by Stuart Elliot of BRT Shooters Supply, Brisbane, Australia.
Share the post "How to Shoot DOTS — Insanely Small Groups at 200 Yards"
We first ran this story a few seasons back. Since then we’ve received many questions about this gun, so we thought we’d give readers another chance to learn about this truly innovative, switch-barrel “convertible” rifle. This gun works for both short-range (100/200) and long-range (500-1000 yd) benchrest matches.
You interested in a truly innovative bench gun that can shoot both short-range and long-range matches? Check out Seb Lambang’s original “do-it-all” rifle. This switch-barrel rifle combined two very different chamberings: 6 PPC and .284 Winchester. With that caliber combo, Seb’s covered from 100 yards (LV/HV mode) all the way out to 1000 (LR Light Gun mode). But the dual chambering is not the rifle’s only trick feature. Exploiting the long-range benchrest rules on stock designs, Seb has fitted a 3″-wide, flat rear metal keel to the buttstock. That counter-balances his 30″-long 7mm barrel, improves tracking, and adds stability. Seb built the stock and smithing was done by Australian gunsmith David Kerr.
Detachable Hammerhead Wing Section Plus Fat-Bottom Keel
To further reduce torque and improve tracking, the stock features an 8″-wide, detachable fore-end fixture. This “hammerhead” fore-end section has extended “wings” on both sides, making the rifle super-stable. The hammerhead unit can be removed, leaving the stock 3″ wide for use in registered benchrest matches where 3″ is the maximum width. The photos below show Seb’s gun in .284 Win Long-Range (LR) Light Gun mode, complete with front wings and rear keel.
Yes This Rig Shoots … In Both Configurations, Long-Range and Short
Seb has already used his switch-caliber, switch-barrel rig successfully in competition. Seb tells us: “The gun shot and tracked real well either in 6 PPC LV/HV mode or in .284 Win LG mode. I love it! Back in 2015, with this gun I placed Top 10 for the Two-Gun at the Harry Madden Championship in Brisbane, Australia just a few days ago and took the silver medal for the 500m Flyshoot with the .284 Win on the next day. So who says a switch-barrel rifle can’t (or doesn’t) work?” And get this, Seb finished the stock just four days before the Brisbane match. He glued-in the action the evening before the match and shot it the next day in competition. Pretty impressive we’d say….
6 PPC and .284 Win Convertible Rifle Specifications
Action: Stolle Panda Short Action (glue-in plus front/rear alum. pillars), Right Bolt, Right Port, Right Eject, .473 bolt face.
LV/HV Weight: Rifle weighs 10.4 lbs in 6 PPC mode (no keel, no front wings).
LV/HV Barrel: Krieger 21.5″ OAL, 6mm (6 PPC, .270″ neck), 1:14″ twist.
Light Gun Weight: 15.5 lbs in .284 Mode with 3″ rear aluminum keel and 8″ fore-end attachment.
Light Gun Barrel: Maddco 30″ OAL, 7mm (.284 Win, .316″ neck), 1:9″ twist.
Metal: Home-made, one-piece scope base with +15 MOA scope rings.
Seb Lambang — Indonesian Innovator
Sebastian (“Seb”) Lambang is the designer/builder of the innovative SEB Coaxial rests, some of the best joystick rests on the market. The SEB Mini is a remarkable design — very compact but solid enough to win F-Class matches. And the SEB Neo Rest has become the go-to choice for short-range and long-range benchrest. The NEO folds flat for transport, yet offers extended vertical and horizontal travel and a rest top that can adjust from roughly 2″ wide to over 6″ in width. This Editor uses a SEB Neo for both bench and F-Class shooting and it is my favorite joystick rest. Here’s a video review of the SEB Mini, filmed at the Ben Avery Range in Phoenix:
Seb is actually in the USA right now, competing at the Berger Southwest Nationals (SWN). No he’s not shooting his radical Hammerhead at Ben Avery this year — he’s got a more conventional F-TR rig. He is shooting with the Int’l Pickup F-TR team coached by Dean Wheeler. In the 2/6/2020 Team Palma match, Seb finished with high score for his team, 438-9X.
ADDENDUM — Seb Succeeds at SWN in Sharpshooter Division:
Seb just posted this report from the Berger SW Nationals in Phoenix: “Proud to get first place in Sharpshooter Class in the Long Range Day 1 Aggregate. Super tough F-CLASS match against lots of the best shooters in the USA and some other countries. Thanks a bunch to my gunsmith Alex Wheeler who did a really great job, [providing a] super-smooth timed action. Thanks also to Tom Mousel who did a great job with the super-accurate ammo! Thanks to Will McCloskey for the best laminate wood rifle stock on the market. The rifle shoots GREAT. I really enjoy this match!”. Here is Seb on the firing line at Ben Avery. The rifle rests on the SEB Joy-Pod joystick bipod he created.
[NOTE: The NRA has multiple divisions: High Master, Master, Expert, Sharpshooter, and Marksman. The most elite level is High Master.]
Share the post "Sunday GunDay: Seb’s Hammerhead Dual-Discipline Rifle"
by James Mock
After owning three different rifles with BAT actions, I have become a loyal fan of BAT Machine quality and customer service. Back in 2009, I traded my BAT/Scoville for the BAT/Leonard that I currently shoot. This rifle has a long history and Terry Leonard told me that “Old 87″ (as I have named it) was one of the earlier BATs that he stocked. He wrapped the stock in fiberglass and used 2-part epoxy back then. I must say that this rifle has held up remarkably well since it dates back to the 1990s. The action is a RB/LP/RE octagon Model B with .308 bolt-face.
Rifle Has Multiple Barrels for Multiple Disciplines
With this gun, I have shot several barrels of different calibers (.22 PPC, .22 PPC-short .095, 6mm PPC, 6XC, 6mm Dasher, .30BR, and will soon have a 6 BR-AI). It has been an exceptionally accurate rifle in several disciplines. In the hands of previous owners, it earned several Hall-of-Fame (HOF) points, and a “middle-of-the-pack” shooter (me) even received a HOF point with this rifle.
For most of its life, Old 87 served as a short range benchrest rifle, but I have used it for the last few years as a 600-yard rifle with the 6mm Dasher barrel. I was lucky enough to earn the Shooter of the Year award at the Prince Memorial Range in Louisiana for 2016.
After shooting my two Dasher barrels for last eight years, I have noticed a drop-off in accuracy at 600 yards. A decision had to be made — get a new barrel or sell the rifle and retire from competition. I will be 74 years old in six months and my competition days are limited due mainly to a chronic neck problem. After mulling over the decision to retire or not, I decided to give Old 87 one more year. Here is the story of how we upgraded the old war-horse.
Old 87 REBORN — Upgrading with New Components
I prefer cut-rifled barrels with four lands and grooves and have had success with .236 bore diameters and 1:8″ twist in long range rifles. I searched for barrels meeting those parameters and found a suitable BRUX at Bugholes.com (Southern Precision Rifles).
The 6BR-AI Option — Easy Fire Forming
I thought about having Billy Stevens chamber it for the Dasher, but decided to try something new. There seems to be a lot of interest in the 6BR-AI and I said, “Why not?” Well, I bought a shortened Dasher die from Harrell’s and will use my Wilson Dasher seating die. Bart Sauter was kind enough to let me use his reamer for chambering.
Fitting a New Roller-Type Cocking Piece on Older BAT Action
Since I was into the project this deep, I called Mike Ezell and ordered one of his Tungsten powder-dampened tuners. Since Old 87 had thousands of rounds since the firing pin spring has been replaced, I decided that it was probably needed. Well, I got to thinking (very dangerous) and asked Daryle Thom if it would be feasible to put a roller-type cocking piece and a new firing pin spring on such an old action.
The folks at BAT are very accommodating and they said that it would be no problem with such a conversion. While my bolt was in Idaho, the barrel with Ezell tuner arrived and I could not shoot it. However, my friend Jeff Turner loaned me his BAT bolt to see if it would work. Although the rifles differ in age by 15 or more years, the borrowed bolt worked perfectly in my rifle. This is a testimony to the great machine work performed at BAT Machine.
New Bolt Roller Tail-Piece Makes a Big Difference in Cocking Effort
With the borrowed bolt I managed to fire-form 50 rounds and get them ready for our 600-yard match on September 16. The folks at BAT quickly fixed my bolt by replacing the mainspring and ejector spring, polishing the ejector, and replacing the tail-piece with their roller type. Pictured below is this tail piece that makes a remarkable difference in the force needed to cock the action. It is amazing what this little wheel can do… even when placed in a 20+ year old action.
Working with the Ezell Barrel Tuner — Small Increments Work Best
Also, I would like to congratulate Mike Ezell on his new tuner which contains powdered Tungsten. It is easy to set up and Mike will help a buyer get maximum effectiveness from the unit. Just give him a call. Below is a picture of the tuner. I was lucky enough to have some time to “play” with it before the match.
Talking about the tuner, Mike writes: “Our new barrel tuners…
PDT stands for particle dampening technology. The science is there, we just applied it to a barrel tuner. The advantages are a wider tune window and more efficient control of barrel harmonics…in a tuner design that actually looks good.”
Mike advised me to set the tuner by turning it all the way into the shoulder and then come out to zero or the second time zero comes up if there is not at least half of a turn between the shoulder and the first zero. It is best to start with a proven load and adjust the tuner from that load. As unlikely as it seems, a rifle can go from a good tune to a very poor tune with only 5 marks (.005”) and vice versa.
Mike cautions those who use his tuner to NOT make adjustments which are too large. As a matter of fact, he recommends adjustments of .001 inch at a time. Ezell’s tuners are screwed onto the barrel with .900” by 32 threads per inch and has 32 marks on the circumference of the tuner. Therefore, each mark moves the tuner in or out by .001 inch. There are three set screws with Teflon tips which provide friction for the tuner on the threads. Do not tighten the screws so tight as they damage the fine threads.
If you want the smoothest bolt possible for your BAT, call or e-mail Daryle or Bruce Thom at BAT Machine and discuss your needs with them. I am sure glad that I did. If you want a state-of-the-Art tuner for your barrel, give Mike Ezell a call or visit his Ezell Custom Rifles Facebook Page.
— Good shooting, James Mock
Share the post "Old Benchrest Rifle Gets New Life as 6BR Ackley with Tuner"
Report By Boyd Allen, IBS Vice President Huge credit to Ken Frehm for all of the photos and most of the information.
On July 14th and 15th, at the Camillus Sportsmen’s Club, Camillus, NY, thirty-two shooters vied to win the Two Gun (and Class titles) at the NY State IBS Championship & 19th Annual Pro-Am Group Shoot. The Pro-Am is a cash match. Twenty-five of thirty-two shooters participated in the cash option — five dollars per gun per day. They were the Professionals. The remaining seven were the Amateurs.
The weather was balmy and mild, the prize table and cash awards were generous, and the new range improvements were extensive, expensive, and well executed. Overall temperatures were seasonally moderate and the wind, while not difficult, was challenging enough that there were no Teen Aggregates shot in any class.
IBS Competitors Talk about their Sport
Definitely check out this video — it is excellent, and well worth your time. It shows the Camillus Club Range and features informative interviews with many shooters:
The Two-Gun Overall match winner was Bob Brushingham, with Don Francis in second place, and Bob White in third. Don, who finished with a .2600 Grand Agg, edged Bob (.2601) by a mere .0001! That’s close! (SEE Full Two-Gun Results).
Two Gun top finishers (L to R): Bob White (3rd), Bob Brushingham (1st), Don Francis (2nd)
Click image for large version.
Below are the LV and HV Class winners, Class Top Ten results, and respective equipment lists.
Light Varmint top finishers were (above, L to R): Bob Brushingham (2nd LV 100), Henry Miller (1st LV 200), Don Francis (1st LV 100, 3rd LV Grand), Leonard Burdick (2nd LV 200, 2nd LV Grand), Don Jeffers (3rd LV 100, 1st LV Grand).
Click image for large version.
Heavy Varmint top finishers were (above, L to R): Bruce Lachapelle (1st HV 100), Robert Blanchard (3rd HV 100), Bob Brushingham (2nd HV 200, 1st HV Grand), Don Francis (2nd HV 200), Ron Burdick (2nd HV 100, 3rd HV Grand), and Bob White ( 1st HV 100, 2nd HV Grand).
Click image for large version.
Here is the winning Pro-Am Team: Jennaro (Jerry) Corigliano (1st Amateur), Bruce Lachapello (1st Pro).
IBS 100/200-Yard Benchrest Competition
As with all Registered IBS 100/200-yard Group Matches, the N.Y. Championships at Camillus employed moving backers. This system ensures that a completed group includes the requisite five shots. With extremely small groups in the “ones” and “zeros” it may be impossible to distinguish five holes.
Although pre-loading is not uncommon, most 100/200-yard group shooters typically load at the match, often between relays. This enables them to tune their loads for the current conditions. Nearly all competitors in this short-range discipline shoot the 6mm PPC cartridge, or a PPC variant.
With group sizes so small, and group dimensions listed to the thousandth of an inch, precise measurement is an important part of the process.
The Camillus Sportsmen’s Club Range
This is not just a benchrest club, but a complete, multi-discipline shooting sports facility. To my California eyes, the Camillus range is a thing of beauty, with a vast expanse of well-trimmed grass between the firing line and the berms, and a substantial wooded hill beyond. The club has just completed a host of brand new improvements that required a significant investment and, I am sure, a lot of hard work. I believe that this was the first time that an event was held after they were finished. The improvements include a new shooting pavilion (firing line cover), with the latest safety features, new all masonry benches, new berms, new target boards, and may others that are too numerous to mention.
Backing up the range berm is a 120-foot high wooded hill. Behind the firing line, running northwest along the club’s western boundary, is the old, abandoned Erie Canal. The Club’s land is relatively flat, which has allowed it to be well-utilized for multiple shooting sports. See Google Map.
Parting Shot… I had to smile at this picture of the target crew. Evidently the club has excellent relations with the Syracuse Police Department.
Share the post "2018 IBS New York State Group Benchrest Championship"
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
This is not just a benchrest club, but a complete, multi-discipline shooting sports facility. To my California eyes, the Camillus range is a thing of beauty, with a vast expanse of well-trimmed grass between the firing line and the berms, and a substantial wooded hill beyond. The club has just completed a host of brand new improvements that required a significant investment and, I am sure, a lot of hard work. I believe that this was the first time that an event was held after they were finished. The improvements include a new shooting pavilion (firing line cover), with the latest safety features, new all masonry benches, new berms, new target boards, and may others that are too numerous to mention.
