Do you often load at the range? Or maybe you need to transport loading gear when you travel in your RV. Well here is a smart transport option — a metal box that holds tools, dies, arbor press, case-trimmer, even a ChargeMaster.

Some guys have built their own loading tool-boxes from wood. Other may stuff gear in a couple of plastic range boxes. But clever Chris Covell came up with an even better solution. Chris sourced a handsome, sturdy metal Horse Grooming Box from eBay. Chris reports the multi-feature metal box “works perfectly for reloading. My ChargeMaster is now out of the wind.”

Bullets, Trickler, and Priming Tool on Top
On top, below the hinged metal lid, is a large compartment that holds Covell’s funnels, scales, priming tool, trickler and other vital gear (photo on right). This top compartment is deep enough to handle wide-mouth funnels with no problem.

Slide-Out Drawer with Dividers
Below the top level is a handy sliding drawer with multiple dividers. This is perfect for holding Covell’s inline seating dies, case-neck deburring and chamfering tools, among many other smaller bits and pieces.

In the bottom of the Horse Grooming box is a large compartment that holds bigger gear. In the bottom section, Covell places his RCBS Chargemaster Lite, along with a case-trimming tool, an arbor press, and various other bulky tools. Check it out:

Folks who load at the range need to bring a lot of gear — reloading presses, powder dispensers, scales, funnels, sizing/seating dies, brass prep tools and more. And there may be other important items to transport — such as ammo caddies, LabRadar mounts, over-size rest feet, and even barrel fans. With this metal box you can easily organize (and protect) al that gear. This box was sourced affordably via eBay.

Do you often load at the range? Or maybe you need to transport loading gear when you travel in your RV. Well here is a smart transport option — a metal box that holds tools, dies, arbor press, case-trimmer, even a ChargeMaster.

Some guys have built their own loading tool-boxes from wood. Other may stuff gear in a couple of plastic range boxes. But clever Chris Covell came up with an even better solution. Chris sourced a handsome, sturdy metal Horse Grooming Box from eBay. Chris reports the multi-feature metal box “works perfectly for reloading. My ChargeMaster is now out of the wind.”

Bullets, Trickler, and Priming Tool on Top
On top, below the hinged metal lid, is a large compartment that holds Covell’s funnels, scales, priming tool, trickler and other vital gear (photo on right). This top compartment is deep enough to handle wide-mouth funnels with no problem.

Slide-Out Drawer with Dividers
Below the top level is a handy sliding drawer with multiple dividers. This is perfect for holding Covell’s inline seating dies, case-neck deburring and chamfering tools, among many other smaller bits and pieces.

In the bottom of the Horse Grooming box is a large compartment that holds bigger gear. In the bottom section, Covell places his RCBS Chargemaster Lite, along with a case-trimming tool, an arbor press, and various other bulky tools. Check it out:

Folks who load at the range need to bring a lot of gear — reloading presses, powder dispensers, scales, funnels, sizing/seating dies, brass prep tools and more. And there may be other important items to transport — such as ammo caddies, LabRadar mounts, over-size rest feet, and even barrel fans. With this metal box you can easily organize (and protect) al that gear. This box was sourced affordably via eBay.

Chris Covell’s Range Box was featured on the Benchrest Shooting and Gunsmithing Private Group Facebook Page. You may want to sign up for this Group — with membership you can access a wealth of information for accuracy-oriented shooters.

Powder Valley now offers RCBS Reloading tools and components as part of PV’s large selection of shooting sports and reloading products. So now, when ordering powder, primers, brass, ammo, and bullets, you can also add dies, reloading tools, and even a RBCS reloading press. “Powder Valley already offers an extensive line of reloading components, including Federal, Speer, and Remington bullets, CCI and Federal primers, and Alliant powders. The expansion of our Reloading Tools and Equipment line makes perfect sense” said Bill Clinton, CEO of Powder Valley. “This is one more way we can [benefit] our Customers and serve their reloading needs”.

CLICK HERE to see the wide variety of RCBS products now in stock at Powder Valley. You’ll find powder dispensers, priming tools, reloading presses, case prep tools, plus a wide selection of reloading dies.

A Short History of RCBS (And the Origin of the “RCBS” Name)
RCBS was founded in 1943 by Fred T. Huntington in Oroville, California. Huntington was a dedicated shooter but found it difficult to obtain quality varmint bullets. However, after reading about making a die to swage .22 rimfire cartridge cases to form jackets for bullets, he began to craft his own dies in the back room of his father’s Oroville laundry and dry-cleaning business. Because the resulting bullets were used to shoot rock chuck varmints, he named them Rock Chuck Bullet Swage dies, later shortened to RCBS.

RCBS soon outgrew this modest beginning. By 1958, RCBS expanded to a 7,500-sq-ft factory that quickly grew to 50,000 square feet. With time, more expansions have occurred, but RCBS stayed near its roots. Oroville is still the major location for RCBS production. RCBS is now a subsidiary of Vista Outdoor, which also produces Federal and CCI ammunition and primers, Alliant powder, and many other products.

Visit https://www.powdervalleyinc.com/brand/rcbs/ to see Powder Valley’s full inventory of RCBS products.

As part of its big Christmas Season Sale, Midsouth Shooters Supply has discounted RCBS products — the line-up of green-colored Presses, Reloading Kits, ChargeMaster Scale/Dispensers, Case Prep Centers, Tumblers and more. We’ve checked around, and right now you’ll find some really great deals on RCBS equipment at Midsouth. For example Midsouth has the Rock Chucker Supreme Press at $169.99 with FREE Shipping. That’s over sixty bucks less than some other sellers charge. And you can get the ChargeMaster Link Powder Scale/Dispenser for just $269.99, $22 less than the current Amazon price.

Do you often load at the range? Or maybe you need to transport loading gear when you travel in your RV. Well here is a smart transport option — a metal box that holds tools, dies, arbor press, case-trimmer, even a ChargeMaster.

Some guys have built their own loading tool-boxes from wood. Other may stuff gear in a couple of plastic range boxes. But clever Chris Covell came up with an even better solution. Chris sourced a handsome, sturdy metal Horse Grooming Box from eBay. Chris reports the multi-feature metal box “works perfectly for reloading. My ChargeMaster is now out of the wind.”

Bullets, Trickler, and Priming Tool on Top
On top, below the hinged metal lid, is a large compartment that holds Covell’s funnels, scales, priming tool, trickler and other vital gear (photo on right). This top compartment is deep enough to handle wide-mouth funnels with no problem.

Slide-Out Drawer with Dividers
Below the top level is a handy sliding drawer with multiple dividers. This is perfect for holding Covell’s inline seating dies, case-neck deburring and chamfering tools, among many other smaller bits and pieces.

In the bottom of the Horse Grooming box is a large compartment that holds bigger gear. In the bottom section, Covell places his RCBS Chargemaster Lite, along with a case-trimming tool, an arbor press, and various other bulky tools. Check it out:

Folks who load at the range need to bring a lot of gear — reloading presses, powder dispensers, scales, funnels, sizing/seating dies, brass prep tools and more. And there may be other important items to transport — such as ammo caddies, LabRadar mounts, over-size rest feet, and even barrel fans. With this metal box you can easily organize (and protect) al that gear. This box was sourced affordably via eBay.

Chris Covell’s Range Box was featured on the Benchrest Shooting and Gunsmithing Private Group Facebook Page. You may want to sign up for this Group — with membership you can access a wealth of information for accuracy-oriented shooters.

Erik Cortina is one of the nation’s top F-Class shooters. A member of Team Lapua-Brux-Borden, Erik has been a top performer at National and World F-Class Championships. Erik is also a very smart guy and a skilled toolsmith who has upgraded his shooting equipment in interesting ways. Today we feature three “How-To” videos from Erik. These show how to upgrade a SEB Coaxial Rest, how to improve the performance of an RCBS Chargemaster, and how to create your own Modified Case for measuring length to lands. Watch and learn…

1. How to Make a Modified Case for the Hornady OAL Tool

In this video, Forum member Erik Cortina shows how to create a custom modified case for use with the Hornady Lock-N-Load Overall Length Gauge (formerly the Stoney Point Tool). While Hornady sells modified cases for many standard cartridges, if you shoot a wildcat such as the 6mm Dasher or .284 Shehane, you’ll need to create a custom modified case. And even if you shoot a standard cartridge such as the .308 Win, you can get more consistent measurements if you make a custom modified case from a piece of brass fired in your chamber.

MORE INFORMATION: Want to learn more? We published a much longer story in which Erik explains in greater detail how to made the Modified Case. That article illustrates the 5/16″ – 36 RH HSS Tap required and shows how to set up the lathe to drill and tap your case. If you are serious about making your own Modified Cases, you should Read the Full Article.

2. How to Upgrade your SEB Co-Axial Joystick Rest

Joystick (coaxial) rests are used by top shooters in benchrest and F-Open disciplines. With coaxial rests, you can adjust both vertical and horizontal aim instantly in one fluid movement — there are no mariner wheels to spin or knobs to turn. Just gently stir the joystick to move up, down, or sideways. Erik Cortina explains: “If you want to get into F-Class (Open) and want to win, you should get a SEB rest. SEB makes an excellent product, but the one thing we upgrade automatically … is adding the F-Class feet. These have a bigger footprint and a spike on the bottom [so you can] dig the feet into the ground and make your rest a lot more stable.” In this video Erik installs a set of Blake Machine Co. F-Class feet. These feature a set-screw, so they are easy to attach and then remove for travel (no Loctite!). “Simple yet effective” declares Erik.

In the second half of the video (starting at 5:30), Erik installs a Dan Bramley Joystick Holder. This features two clamp-on cradles that hold the joystick crosswise below the top (see photo). This handy accessory ensures your handle always remains with the rest (and doesn’t get left at home when you travel to a big match). This joystick holder has been popular with competitors. Erik says, “The Bramley Joystick holder is $60.00 — money well spent.” To order, email Dan at dbramley [at] yahoo.com.

3. How to Make the RCBS ChargeMaster 1500 Work Better

Erik Cortina has been fiddling around with his RCBS ChargeMaster and he discovered something interesting. Through a series of tests he determined that the ChargeMaster dispensed slightly more precise charges when he trickled the last few 10ths of a grain on to the RCBS pan. Erik wasn’t expecting this result, but he confirmed there may be a slight benefit to this trickling method (as opposed to allowing the ChargeMaster to dispense the full charge). You can see Erik’s test procedure in this video:

We should note that Erik’s preferred method of weighing powder is to first dispense a slightly lower charge with the RCBS, transfer the pan to a laboratory-class Sartorius magnetic force restoration scale, then trickle up with his Omega (Dandy Products) Powder Trickler. However, if you don’t have a $800+ laboratory-grade scale, you might just try trickling on to the ChargeMaster pan.

MORE INFORMATION: We have published a more lengthy Bulletin Article that covers Erik’s Chargemaster Performance Findings in greater detail. That article has more photos plus a clever, bonus “Beep Defeat Tip”. If you own a Chargemaster, we recommend you READ the Full Article.

Sierra Bullets asked a few hand-loaders to reveal their favorite reloading tool or accessory: “What is your favorite ‘don’t know how you ever lived without it’ piece of reloading equipment?” Some of the answers are listed below. We were interested to see some high-tech, micro-processor items mentioned, such as the AMP Annealer, and the AutoTrickler powder dispenser. Old standbys, such as the rugged RCBS Rockchucker and Dillon 650, also made the favorites list. You can nominate your own favorite reloading hardware in the comments section of the Sierra Bullets Blog.

Sierra Bullets Ballistic Technician Philip Mahin answered: “A comparator gauge to measure from the base of a case to the ogive of the bullet. This bypasses the tip of the bullet, so I can repeat the same seating depth the next time I visit a specific combination.”

Bill, Editor of Rifleshooter.com, answered: “I have so many favorite reloading tools, it’s hard to pick one. But if I had to, it would be my Forster Co-Ax press. I like the ease [with which] you can change dies and that it doesn’t require traditional shell holders. It’s a great tool to have!”

Sierra Bullets Ballistic Technician Duane Siercks answered: “I don’t know that you would actually call this equipment, but the item that comes to mind would be my reloading room/shoot house. I had always had to squeeze everything into a corner or even an unheated shed. After we bought our current house, I built a garage and placed it so that I had a window looking down a 250-yard range. I built a dedicated room with heat and A/C. It contains my reloading bench and a shooting bench. The shooting bench lets me slide open the window and shoot down the range. It is very handy to not have to load everything up to go to the range. It also makes load development a lot simpler and efficient. I don’t know how I ever got along without it.

I also wonder what I did before I acquired the Lyman 1200 DPS Powder Dispenser. This has made the process so much simpler and much easier. I also have a Lee Precison Universal Decapping Die that I would gladly spend the money on again. This may be a small thing, but it certainly is handy. The Lee would accommodate some very large cases that some of the others were too small for.”

Jon Addis answered: “Putting an A&D FX-120i scale with AutoTrickler and Auto-Throw on the bench has changed the way I reload. It’s kernel accurate in about 15 seconds. Saves time and reduces a variable. And of course, the system is made better by the Area 419 Billet Adjustable base for the trickler and Billet Powder Cup.”

This video shows the AutoTrickler V2 and Auto-Throw Combo:

Sierra Bullets Ballistic Technician Carroll Pilant answered: “Dillon 550 and 650 presses.”

Sierra Bullets Ballistic Technician Paul Box answered: “The Lee Precison hand priming tool.”

Sierra Bullets Chief Ballistician Tommy Todd answered: “A brass annealing machine and a RCBS Chargemaster complimented with a Sartorious scale.”

Sierra Bullets Ballistician Gary Prisendorf answered: “RCBS Rock Chucker Press, it’s built like a tank, and it will last me a lifetime.”

Sierra Bullets Production Manager Chris Hatfield also answered: “RCBS Rock Chucker single-stage reloading press.”

Jeremy Kisner answered: “My Giraud trimmer has taken [three operations] and combined them into one easy task. I can now size my brass and then sit down and trim, chamfer, and debur to a 0.001″ tolerance in one motion.”

Dan Blake answered: “My Annealing Made Perfect (AMP) annealer. With consistent neck tension being one of the largest contributions to small Extreme Spread on muzzle velocities, I believe this induction annealer is truly the best on the market.”

This manufacturer-produced video shows how the AMP annealing machine operates:

Trevor Aldinger answered: “Area 419 Master Funnel Kit. In the past I’ve used plastic funnels and even other metal ones. This system fits case necks and flows much better than any others I’ve used, and there is no static since it’s metal. We spend a lot of time and money to get precise charges, I don’t want to lose or miss a kernel because of a cheap funnel.”

Tyler Riley answered: “My RCBS bench primer (priming tool). It has a lot more leverage than a hand primer and still has a good feel to how tight primer pockets are. Makes it much easier on my hands to prime large runs, especially new brass with tight pockets.”

Craig Arnzen answered: “My Annealeez [annealing machine] is one of the best tools in my reloading room. Neck tension is SO important, and annealing every firing really helps with that. This is an inexpensive tool that can anneal a lot of cases at once, and help me produce more consistent ammo.”

Josh Temmen answered: “Time is critical for me so my RCBS Chargemasters are indispensable (pun intended.) They cut down on time at my reloading bench while maintaining the weight tolerances required for long range shooting.”

Josh Bartlett answered: “I have my Dillon 650 set up with Whidden floating tool heads to do decapping and sizing on my match ammo. The case feeder and progressive function of the press save me a TON of time when doing lots of several hundred rounds.”

Ryan Brandt answered: “… A quality set of calipers. My reloading room is full of very nice equipment but little does more to satisfy my perfectionism than a good check with the calipers.”

At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.

1. Palmetto State Armory — JTS M12AK 12ga Shotgun, $399.99

For home defense, it’s hard to beat a shotgun. And a magazine-fed, semi-auto AK-type shotgun offers serious firepower in a compact package. This JTS M12AK 12ga 18″ Shotgun, features the proven, ultra-reliable AK47-type action. Yes it works great with shotshells. This 18″-barrel, 4.9-Star rated, semi-auto firearm takes a variety of magazine sizes, and is Saiga-mag compatible. If you want a high-capacity scatter-gun, this is a solid value at $399.99 from Palmetto State Armory.

2. Costco — Cannon Large Executive Safe, $699.99 (Save $200!)

$200 manufacturer’s savings is valid 3/30/20 through 4/27/20. While supplies last.

Being a responsible gun owner means securing your weapons at all times. However, not everyone can afford a multi-thousand dollar safe. Cannon Safe has been making quality yet affordable safes for decades. Now you can grab Cannon’s Executive Series Safe for $699.99. This is a BIG, 43.8 cubic foot-capacity vault with 60 minutes fire protection. Price for this large 59″ H x 45″ W Safe is just $699.99 INCLUDING SHIPPING! This is an amazing deal for a very big safe. NOTE: Just last week this same safe was $899.99 at COSTCO, so you Save $200!

3. Midsouth Shooters — Fiocchi 9mm Luger Ammo, $12.99/50

Currently pistol ammunition is in very high demand, particularly 9mm Luger (9x19mm). Some dealers have doubled or even tripled the price of their 9mm pistol ammo. Thankfully, Midsouth Shooters continues to offer Fiocchi 9mm Luger ammo for just $12.99 per 50ct box. That works out to $0.26 per round. This is reliable ammo with 115gr FMJ bullets and reloadable brass cases.

4. Optics Planet — Vortex 20-60x60mm Spotting Scope, $399.00

With plenty of high-end spotting scopes available on the market it’s easy to forget there are some very good, affordable spotters out there. Among the better budget-priced spotting scopes is the Vortex Diamondback 20-60x60mm Spotting Scope. Both angled and straight-body versions are on sale now for $399.00. This spotter is backed by a rock-solid, Vortex lifetime warranty. The 20-60X zoom range is ideal for viewing mirage or bullet holes on distant targets.

5. Midsouth Shooters — RCBS ChargeMaster Lite, $219.99

Do you need an electronic powder scale and dispenser? Check out this great deal at Midsouth Shooters Supply. Suggested retail for the ChargeMaster Lite is $299.99. Amazon’s best price for this unit is $269.99. But now you can get it for just $219.99 at Midsouth. So you can save $50.00 with this Midsouth sale. Put the money saved into bullets or powder. The RCBS ChargeMaster Lite is the modern second generation Scale/Dispenser, descended from the original ChargeMaster. The ChargeMaster Lite features an easy-to-use LCD touchscreen. Dispenser precision is plus/minus 0.1 grains. The unit comes with twin check weights and a convenient plastic cover for the powder pan.

6. Graf’s — Tipton Ultra Gun Vise, $99.95

Cleaning and working on your guns requires a solid platform. Most gun cleaning stands aren’t adjustable enough or are too flimsy. Not so with the Tipton Ultra Gun Vise. Weighing-in at about 10 pounds, this beefy gun vise provides a steady base. The frame is metal for strength, features stout adjustable jaws, specialized AR holder, and several accessory trays. Threaded feet allow the vise to be leveled on your bench (or the ground). With this system you can work on just about anything including bolt-action rifles, AR-platform rifles, shotguns, pistols, and even compound bows and crossbows. To fit wide forearms, you may have to remove or modify the front pad(s). Our Deals Editor, who owns this gun vise, reports this is an outstanding product, well worth the $99.95.

7. Amazon — Caldwell Precision Turret Rest, $69.99

Are you tired of big heavy sleds for range shooting but they don’t provide any kind of easy adjustment or target acquisition? Check out the Caldwell Precision Adjustable Turret Rest. It offers quick horizontal and vertical adjustment making it great for target shooting as well as varminting from a bench. Amazon user ‘Jet Mech 1′ reports “…it’s REALLY solid! Solid steel legs and everything is heavy duty. It’s really compact. Easily fits in the smallest car trunk. So, if you’re limited on space going to the range, this is ideal. It holds your firearm very securely. The tilt and pan is super smooth and precise. This is the perfect platform for an AR-style rifle but works equally well for just about anything.”

8. Grizzly or Amazon — Dewalt Storage Box on Wheels, $69.99

Grizzly offers FREE Shipping on this rolling Dewalt box and all non-freight items over $35.00.

More and more we see range bags being traded out for rolling range boxes. Wheeled toolboxes such as the Dewalt TSTAK storage box have become the new go-to way of easily transporting gear to the line. The best part of these systems is that you can easily stack a smaller fitted Dewalt box on top such as the flat top toolbox or the deep drawer organizer and create the range box combo that works best for you. These smaller boxes mate with recesses in the top of the larger TSTAK Deep Box with Wheels.

9. Amazon — Sawyer MINI Water Filtration System, $19.97

The current pandemic has made many people realize they were not prepared for unexpected events. Safe drinking water is vital. If clean tap water is not available, and your bottled water runs out, having an emergency filter is important. At only $19.97 the Sawyer MINI Water Filter is a small and inexpensive way to have an emergency water source during times of crisis.

Black Friday Deals

Here are fifteen (15) of the best individual bargains we found for the Black Friday/Cyber Monday Cycle. We shopped dozens of sites and looked for popular, quality items listed at significant savings — over 70% off in some cases. But don’t hesitate, some of these deals expire tonight. Others are good for four days, through Cyber-Monday at 11:59 pm.

	MidwayUSA — Tipton Best Gun Vise plus Wheeler Eng. Tool Kit, both for $69.99. Save $65.
	Natchez — RCBS ChargeMaster Scale/Dispenser, now $269.99, save over $70.00 compared to other vendors.
	Midsouth — Hornady 6.5mm Creedmoor Brass ($34.99/100) and 6.5mm 140gr ELD Bullets ($64.99/250). Great Deal!
	LongShot Cameras — LR-3 2-Mile UHD Target Camera, $699.00 ($100 Off). Best-in-Class System.
	Natchez — Federal American Eagle 5.56×45 (.223 Rem) Ammo 1000 Rds $289.99. Save $100!
	Amazon — Samsung Android Tablet 8″ Diagonal. Perfect for TargetCam and Ballistics Apps, $141.79. 16 GB Memory; upgradeable with MicroSD card.
	Brownells — Triggertech AR15 Adjustable 2-Stage Trigger. Sale $142.39 with Promo Code HAA (11% Off). Save $107!
	Amazon — GunVault Minivault Biometric Pistol Safe GVB1000, $69.99. Save $250 (78%)!
	MidwayUSA — Nosler BT 6.5 Creedmoor 140gr Ballistic Tip Loaded Ammo, Box of 20, $19.99 ($1/round), Save 39%!
	MidwayUSA — Midway Pro Series Shooting Mat, $32.99. Save $22 (40%) — fine pad for the price.
	Amazon — Frankford Arsenal Quick-N-EZ Vibratory Case Tumbler, $30.49. Save $20!
	Cabela’s — SIG Sauer Kilo 2000 Laser Rangefinder, $219.97. Save $80!
	Cabela’s — Garmin GPSMAP® 64ST Satellite GPS with Altimeter, $169.99. Save $80! Great unit.
	MidwayUSA — Ravine Leather Nylon 7″ Hunting Boots $79.99, save $90.00!
	Midsouth Shooters — Hornady Lock-N-Load AP Auto Progressive Press, $395.95. Save $111!

RCBS has come out with a new, twin-tube powder scale/dispenser that promises to deliver 1- or 2-kernel precision in the slower, more precise “Match Mode”. If it really works, this new RCBS MatchMaster unit could compete with an Auto-Trickler V3 mated to a Magnetic Force Restoration scale. However, the new MatchMaster employs a strain-gauge scale, so it will be interesting to see how the unit actually performs.

This is an impressive new machine, but it represents a signficant investment. MSRP for the MatchMaster is $1123.95 with street price around $899.00 (MidwayUSA). At around $900.00, the MatchMaster competes with an AutoTrickler system, which is definitely fast and highly precise.

Ultimate Reloader Tests the New RCBS MatchMaster
Our friend Gavin Gear of UltimateReloader.com got his hands on one of the first production MatchMasters. Gavin put the machine through its paces in a “first look” video using two powders, Bullseye and Varget. In the video, Gavin explains the machine’s design features. Then he tests the new MatchMaster in both Standard Mode (faster) and the slower, more precise “Match Mode”. Gavin also published a full-length MatchMaster Review with detailed test results.

RCBS claims that the MatchMaster can dispense charges to within ± 0.04 (four hundreths) grain in Match Mode. That’s 1-2 kernels of an extruded powder such as H4350. Gavin’s testing, using an A&D FX-120i Magnetic Force Restoration scale as a control, showed that RCBS’s claims are solid.

Ultimate Reloader RCBS MatchMaster Powder Scale/Dispenser Review

“You can actually fine-tune the settings for the large dispensing tube and the small tube. There are quite a few parameters… quite a bit of flexibility.” — Gavin Gear.

RCBS MatchMaster Features

— MatchMaster offers two modes, Standard (Faster) and Match (More Precise)
— MatchMaster has two powder dispensing tubes, a larger diameter for large flow and a second smaller tube for precise trickle.
— MatchMaster Settings can be controlled with RCBS Mobile App that works through BlueTooth.
— Powder is removed from the BOTTOM of the machine. This means you must lift the unit up off the bench, then plug a drain tube into the bottom of the unit. See photo.

How Accurate Is the MatchMaster?
Near the end of his video review, Gavin threw an 84.20 grain charge of Varget with the MatchMaster. He then weighed the same charge with his A&D FX-120i Magnetic Force Restoration scale. The charge weights agreed exactly at 84.20 grains. When the same pan was placed a second time, the FX-120i showed 84.16 grains. That’s still a mere 0.04 grain variance, which is RCBS’s stated precision claim for Match Mode.

Note: This shows first placement of pan on the A&D FX-120i. A second placement of pan on FX-120i stabilized at 84.16 grains.

How Fast is MatchMaster in Each Dispensing Mode?
Gavin started testing the MatchMaster in Match Mode with Bullseye, a popular flake pistol powder. With a 24.00 grain Bullseye charge, one dispensing took 26 seconds (11:40 time-mark), while another took 40 seconds (12:30 time-mark), an average of 33 seconds. In standard mode, the MatchMaster dispensed 24.0 grains of Bullseye in 18.5 seconds average (15.03 time-mark, 15:32 time mark). So Standard Mode was 44% faster with Bullseye.

Next Gavin filled the machine with Hodgdon Varget powder and dispensed a 25.0 grain charge in Standard (Fast) Mode. The first try took 12 seconds (18:30 time mark) to dispense the charge, while the second run of 25.0 grains took just 11 seconds (18:50 time mark).

“Hodgdon Varget performed VERY well with the MatchMaster powder dispenser. I would call this powder the ‘Speed King’ here — it dispensed way faster than the Alliant Bullseye with the settings I used, and I only had one overage which was corrected when I changed powder settings. Bravo!” — Gavin Gear

Then Gavin switched to Match (Precise) Mode and dispensed two more 50.00 grain charges of Varget. These two precision throws finished in 20 seconds (20:38 time mark) and 17 seconds (21:09 time mark) respectively, for an 18.5 second average. That’s very good for large 50.00 grain charges, although the first charge was actually 50.06 grains, about two kernels high. But Gavin explained that the machine permits fine-tuning of the powder type setting. He changed this to account for larger extruded kernels and got a perfect 50.00 grain throw in 35 seconds (22:01 time mark). The “customized” powder settings can be loaded into the RCBS MatchMaster App for future use (See below):

Conclusion — Initial Tests Show Good Performance
Based on Gavin’s testing, the MatchMaster delivers on its promises. With Varget extruded powder, it was quite fast, even in “Match Mode”. The dispensed charges were exact within .04 (four hundredths) of a grain, i.e. a couple of kernels, as confirmed by the A&D FX-120i Force Restoration Scale. Gavin actually liked the system of removing the powder through the bottom of the machine, using the supplied tube. It takes some practice, but it worked fine, as you can see in the video.

The RCBS MatchMaster employs a strain-gauge scale. It remains to be seen if there is a bit of drift, as you will observe with strain-gauge dispensers in the $200-$300 range, such as the original RCBS ChargeMaster. During his MatchMaster test session, Gavin said he did not observe any drift, a good sign. Overall, it looks like this is an impressive machine. But, with a $899.00 price, this is a serious investment. Anyone considering the new MatchMaster will also want to look at the AutoTrickler V3 system with AutoThrow. It costs $520.00, NOT including a lab-grade Magnetic Force Restoration balance ($600 to $1000+).