Jason Baney was one of the “founding fathers” of this website when we started out as 6mmBR.com 18 years ago. A few seasons back, Jason created an interesting wildcat, a mid-sized 7mm cartridge based on the 6.5×47 Lapua case. In this report, Jason (who now works at Eurooptic.com) talks about his 7×47 wildcat and his initial velocity (and feasibility) tests. To determine the 7×47’s velocity potential, Jason did a multi-stage test, cutting a barrel in two-inch increments. This process is illustrated in a video, embedded below.

You may be surprised that the little 7×47 cartridge could drive a 180gr Berger Hybrid at 2770+ FPS with a 32″ barrel and Reloder 17. Max Velocity with H4350 (and 32″ barrel) was roughly 70 FPS slower. With a 24″ barrel length, the 7×47 was still able to propel the 180gr Hybrids over 2600 FPS with H4350. That’s impressive performance for a mid-sized cartridge pushing a very big bullet.

7×47 Lapua Wildcat — Great Accuracy and Surprising Velocity

By Jason Baney, Eurooptic.com
The biggest enemy in long-range shooting is wind. This also happens to be the hardest to gauge and predict. The only way mere mortals can attempt to defeat the wind demons is to shoot a cartridge with the most ballistic efficiency, yet maintain a user-friendly combination of recoil and component consumption as well as performance on target.

The 7mm bullets tend to yield the best compromise of all of these aspects. Their BC-to-weight ratio is outstanding and 7mm bullets provide sufficient impact energy for most situations. In addition to that, the recoil of 7mm bullets can be more manageable than heavier/larger .30 and .338 caliber projectiles.

In cartridge design, of course you want the best case possible. Having used the 6.5×47 Lapua since its release in 2006, I felt this cartridge was the perfect choice to start with as I wanted a true short-action non-magnum round that gave the least possible wind drift to 1000 yards. The 6.5×47 parent case also allowed seating of the heavy 180gr class bullets completely out in the neck yet it maintained an overall length that would actually work in a factory Remington short action magazine.

The 6.5×47 brass from Lapua is as good as it gets and is a very efficient case. The small primer pocket has been a proven winner so no need to change anything. This combination has always given reliable precision and extremely tight velocity spreads.

So here I was, ready to expand a 6.5×47 Lapua to 7mm but a web search revealed no info on a 7×47 wildcat, so test loads would be based purely on an educated guess. My initial assessment/prediction was that heavier 180gr bullets in the larger 7mm caliber would end up at a max load very close to a 140gr bullet in the parent 6.5 caliber. This actually turned out to be a very accurate assumption.

The performance goal of this cartridge was to get a 180gr Berger Hybrid moving at 2720 FPS or faster to be able to shoot inside of a 6.5mm 140gr Berger Hybrid at 2900 FPS. (That 2900 speed is what I was able to achieve with the standard 6.5×47 Lapua). I also planned to try the 168gr VLD as well as the 180gr Lapua Scenar and 162gr Amax, but the specific goal was the beat the 6.5 140gr bullets at 2900 FPS. I believed the 180 Hybrid at 2720 FPS would be the easiest way to accomplish this.

Here are Summary Test Results for H4350 and Reloder 17 for 180s, and IMR 8208 for the 168s. Speeds were clocked by two chronographs at nine (9) barrel lengths, 32″ to 16.1″.

Since this cartridge was a complete unknown I thought it would be quite interesting to see what the 7×47 could achieve at various barrel lengths from very long to very short. We wanted to see which length would best suit the bullet/cartridge combination for max performance. Obviously testing 8-10 barrels at different lengths would be pointless due to natural performance variations between barrels, not to mention expensive and wasteful. I decided instead to attempt a fairly radical test and cut a barrel from 32″ down the 16.1” while chronographing the same loads along the way to see what each combination delivered at the different lengths.

Before I could get started of course a reamer and dies and a few other parts were needed. Dave Kiff at Pacific Tool and Gauge was excited to get going on the project so soon after our phone conversation my one of a kind reamer arrived. Since I had been using Forster dies in the 6mmx47 Lapua and 6.5×47 for all these years, I contacted my friend Bob Ruch at Forster and he was willing to make me a few sets of special dies for the project. Lapua of course provided some brass for the project and Rock Creek Barrels sent a beautiful 1:8.7″-twist 5R barrel blank as a sacrificial lamb. The gunsmith I chose for the chamber job on this project needed to be a tactical long range rifle shooter to appreciate the capability of the round all the way down to its 16.1” barrel length so I asked my good friend Wade Stuteville from Stuteville Precision to help me out.

The rifle I selected for the test was Accuracy International’s new AT rifle. This rifle is basically an overhauled and updated AI AW with a quick user-changeable barrel. I can literally change a barrel in 1 minute or less. The machining they have done to give this function was quite simple and brilliant in the way it retains the barrel yet allows the release quickly and with only a 4mm Allen wrench. This would make the test that I contrived go very smoothly as no major tools were needed.

My goal was to use as many different load combos for the test as I could without making it extremely cumbersome to complete. I wanted to test at least the 180 and 168 Berger as well as a couple different powders representing different burn rates to get an all-around feel for how the cartridge would behave at the different lengths. From previous experience with the 6.5×47, the best powder choices were Hodgdon H4350 and Alliant Reloder 17 (RL17) so these would be the main players. I also picked IMR 8208, Varget, and VV N550 to cover the spectrum of acceptable burn rates. Also, my standard CCI 450 primer was used as that has been successful for me in the 6mmBR and 6.5×47 since 2006 as they are incredibly consistent, however they are also better able to take high pressures without blanking. After picking the powders, I first ran ladder tests to assess max loads in the long 32” barrel.

Velocity Study — Chopping the Barrel from 32″ to 16.1″
Laying out the test actually took a bit of bit of mental gymnastics to provide randomness. The barrel was to be cut in 2” increments from 32” down to a final of 16.1”. Each length was actually pre-scored by Wade to make cutting easier to start and was actually 1/8” long at each mark so when I finally ended up at 16 1/8”, I was able to have the barrel re-crowned without going below legal length.

Six loads were assembled using the five powders mentioned above and two bullets (Berger 168gr VLD and 180gr Hybrid). Each set of rounds to be fired at each cut was predetermined and laid out so that the same load never preceded nor followed another more than once. Reloder 17 and H4350 loads were fired at each cut, while the four others were fired at every-other cut to keep the round count under 200. Twenty rounds (4 loads times 5 rounds each) were fired at each cut from 32” down to 18” and at the final 16.1” length each of the six loads was fired. That is a total of 190 test rounds. The barrel was cleaned before firing at the 24” length and before firing at the 16.1” length. After cleaning each time I fired two rounds of the next load as fouling shots to normalize velocities.

The rifle was fitted with a 3” fore-end attachment and fired from my 40-lb front rest for 1000-yard benchrest competition with a rear bunny-ear bag. Throughout the test, the rifle never changed its position — though the muzzle did retreat 2” with every cut. I used two chronographs for the test. An Oehler 35P was placed 10 feet from the original 32” muzzle and a Magnetospeed V3 was attached on the muzzle (at all barrel lengths down to 16.1 inches.)

After every round of firing, the barrel was removed and we poured cold water on the exterior only and wrapped a wet towel around it to speed cooling. While the barrel was cooling we used a couple C-clamps and a 2×4 to create an impromptu barrel vice to hold it while we were cutting. While it was clamped, we used a simple hacksaw to cut off two inches and crowned the barrel with an RCBS deburring tool for a nice finish. It took an average of two minutes to cut through the barrel at each length.

OBSERVATIONS:
Throughout the test, the rifle lost 3.2 lbs on its way to 16.1 inches. The recoil and muzzle blast increased dramatically from 32″ down to 16.1″. Groups on target were actually quite impressive given that we were not really trying for absolute precision and we had rough-cut crowns. Many groups formed one large hole and several were half-MOA or better – even at the final 16.1″ length.

Each load lost between 12.25-16.8 FPS per inch (loss per inch – LPI) over the entire test, though the rate of the loss varied by the burn rate of the powder and by barrel length. Generally below the 24” barrel length the LPI accelerated rapidly. Initial LPI at the longest lengths was 0-10 FPS, while the loss per inch at the shortest lengths were much higher at 30-55 FPS!

In general I did not quite achieve the velocity I was hoping for, but am very close and intend to test longer throats and different throat geometry to get where I want to be. Below I will break the attainable performance down into 3 barrel lengths for consideration in different disciplines.

APPLICATION ONE: 28-30” Barrel for 1000-Yard Benchrest:
Since I am close to or past my target velocity at the longer lengths (above 2720 FPS with the 180gr Berger Hybrid), I intend to barrel a 1000-yard Benchrest rifle in this caliber and give it an honest try in 1K benchrest. I feel that, with a 28-30″ barrel length, my goal will be attainable and it will pull away from 6.5mm class rounds in the wind drift department. While there will be a slight recoil increase, in a 17-lb rifle it is not a concern. There will also surely be a significant gain in useful barrel life as well.

APPLICATION TWO: 22-24″ Barrel for Tactical/Sniper Matches
For tactical matches, I hoped to achieve good results with a 22-24″ barrel length, but it appears it may be difficult to attain the velocities needed. I have a lot of velocity to make up here to beat the 6.5 round, but will give it a go utilizing a longer throat to gain the velocity. The longer throat in this case will make the round longer than the Remington 700 internal box, but not too long to function in Accuracy International’s AICS and AW-type magazines commonly used in this discipline.

APPLICATION THREE: 16.1″ Barrel for Compact/Concealable Sniper Rifle with Suppressor
Running with a short barrel and suppressor may prove to be what the 7×47 does best. Most 16″ sniper rifles are built around the .308 Win round. In terms of ballistics, The 7×47, even with its current performance, represents a significant gain over a .308 Win in a 16” barrel. The 180gr Hybrid at 2500 FPS shoots well inside a 175gr .30-caliber bullet at the same velocity. Compared to other non-magnum rounds fired in a 16″ barrel, the 7×47 appears very promising (and it beats the .308 Win for wind drift).

All in all, the test was fun, educational, and a moderate success. I am excited to test this round further to see what is possible.

TECH INSIGHT: Bushing Firing Pin Solves Problem with Blanked Primers
The 6.5×47 Lapua has always benefited from small diameter and tightly fitted firing pins for best performance. This is not something you expect from a real-deal LE/Mil sniper rifle though due to reliability concerns. I decided to give the rifle a chance though with the bolt unaltered. However, the results (blanked primers) were immediate and dramatic. Every single load in the initial pressure test blanked primers 10% short of the intended velocity goal. This was not encouraging. The original pin measured about 0.080” while the hole it traveled thru was about 0.084”. While this was not really an over-sized hole, the large pin proved very abusive to the small primers.

To fix this situation we decided to bush the firing pin. The AI’s hardened bolt head presented a challenge. Nonetheless, Wade Stuteville returned the bolt to me with a beautiful bushing-job giving me a 0.065″ pin in a 0.067″ hole (this is what has worked well for me in a couple custom 6.5×47 sniper match rifles for some time). This pin size is a bit of a compromise to leave it less prone to breakage yet solve the primer-blanking issues. On top of that, we reduced firing pin protrusion from approx 0.066” to 0.051”

This bolt and pin modification immediately solved the issue and I have not blanked a single primer since it was modified. After max safe loads were found, I came down a bit for the test loads to make sure I had no issues all the way thru. At this point group sizes were not assessed at all, simply pressure signs.

If you read our lengthy article on Ultrasonic Case Cleaning by Jason Baney, you’ve seen the remarkable results that can be achieved with this method, as shown by the photo above. Ultrasonic cleaning has many advantages over traditional tumbling methods of case cleaning. There is no dust or media residue to remove from the brass, and when done right, the cases come out clean and shiny, inside and out, even the primer pockets.

In its Benchtalk Archives, Brownell’s has an excellent article discussing Ultrasonic Case Cleaning. Brownell’s staff compares results, with measured dwell times from 5 to 75 minutes, using both Mpro-7 and HCS 200 cleaning solutions. Tests are performed with once-fired and 5X-fired Tactical 20 (Tac20) cases, as well as once-fired .260 Rem Cases. The article also compares the results from ultrasonic cleaning vs. tumbling in walnut media. Below are Brownell’s results for Tac20 cases with the HCS 200 (non-acidic solution). Go to Brownell’s article for MPro7 results and Rem 260 results.

How Does Ultrasonic Cleaning Work?
The Brownell’s Benchtalk article explains: “Ultrasonic cleaning uses high-frequency sound waves (generally between 20-80 kHz) to remove a variety of contaminants from objects immersed in a liquid. The result of these high-frequency sound waves is a process called cavitation. These high frequency bursts of ultrasonic energy produce a three-dimensional wave of alternating positive and negative pressure areas as the sound wave passes through the solution. During negative pressure, microscopic cavitation bubbles form and will continue to grown until they reach resonant size. As the positive sound wave passes, the pressure rises rapidly and implodes these tiny bubbles. Before these minuscule bubbles implode they store a tremendous amount of energy. These bubbles can be as hot as 10,000 degrees and have as much as 50,000 lbs per square inch of pressure. This sounds alarming, but you have to remember that these bubbles are microscopic in nature and pose no harm to anything, unless you are a carbon /powder residue deposit on a cartridge case!

When this cavitation bubble implodes near your brass case, it transforms the bubble into a jet about 1/10th of its size. This jet of energy can travel as fast as 400 km/hour. At 43 kHz, as is the frequency for our L & R HCS 200 ultrasonic cleaner, this is happening 43,000 times per second. This micro-burst of extreme energy is responsible for removing contaminants from the surface of your cartridge brass. Ultrasonic cleaning can reach into crevices and inaccessible areas and remove surface debris that can’t be cleaned by any other process.”

Photos and quotes © Brownells®, Inc. All Rights Reserved, Used with Permission.

If you read our lengthy article on Ultrasonic Cleaning by Jason Baney, you’ve seen the remarkable results that can be achieved with this method, as shown by the photo above. Ultrasonic cleaning has many advantages over traditional tumbling methods of case cleaning. There is no dust or media residue to remove from the brass, and when done right, the cases come out clean and shiny, inside and out, even the primer pockets.

In its Benchtalk Archives, Brownell’s has an excellent article discussing Ultrasonic Case Cleaning. Brownell’s staff compares results, with measured dwell times from 5 to 75 minutes, using both Mpro-7 and HCS 200 cleaning solutions. Tests are performed with once-fired and 5X-fired Tactical 20 (Tac20) cases, as well as once-fired .260 Rem Cases. The article also compares the results from ultrasonic cleaning vs. tumbling in walnut media. Below are Brownell’s results for Tac20 cases with the HCS 200 (non-acidic solution). Go to Brownell’s article for MPro7 results and Rem 260 results.

How Does Ultrasonic Cleaning Work?
The Brownell’s article explains: “Ultrasonic cleaning uses high-frequency sound waves (generally between 20-80 kHz) to remove a variety of contaminants from objects immersed in a liquid. The result of these high-frequency sound waves is a process called cavitation. These high frequency bursts of ultrasonic energy produce a three-dimensional wave of alternating positive and negative pressure areas as the sound wave passes through the solution. During negative pressure, microscopic cavitation bubbles form and will continue to grown until they reach resonant size. As the positive sound wave passes, the pressure rises rapidly and implodes these tiny bubbles. Before these minuscule bubbles implode they store a tremendous amount of energy. These bubbles can be as hot as 10,000 degrees and have as much as 50,000 lbs per square inch of pressure. This sounds alarming, but you have to remember that these bubbles are microscopic in nature and pose no harm to anything, unless you are a carbon /powder residue deposit on a cartridge case!

When this cavitation bubble implodes near your brass case, it transforms the bubble into a jet about 1/10th of its size. This jet of energy can travel as fast as 400 km/hour. At 43 kHz, as is the frequency for our L & R HCS 200 ultrasonic cleaner, this is happening 43,000 times per second. This micro-burst of extreme energy is responsible for removing contaminants from the surface of your cartridge brass. Ultrasonic cleaning can reach into crevices and inaccessible areas and remove surface debris that can’t be cleaned by any other process.”

Photos and quotes © Brownells®, Inc. All Rights Reserved, Used with Permission.

This Sunday we feature the German-crafted Merkel RX Helix with straight-pull bolt. We shot the Helix a few years back during Media Day at the Range. One notable difference between the German Merkel and the Austrian Strasser, another straight-pull rifle, is the bolt travel. During cycling, the Merkel bolt stays completely inside the action (see video below at 00:30). By contrast the Strasser bolt moves pretty far back, outside the action. For some folks that makes the Helix better for fast follow-up shots. All we can say is that Merkles and Strassers BOTH cycle way faster than conventional bolt-action rifles.

Merkel RX Helix Range Report

One of the most innovative rifles we have ever shot was the Merkel RX Helix, a very impressive piece of rifle engineering. Merkel claims the RX Helix is the fastest-cycling centerfire bolt action in the world. We can’t confirm that claim, but the Helix certainly cycles faster than any other centerfire bolt-gun this Editor has ever tried. (Yes, a Fortner biathlon action can be worked more rapidly, but that’s a rimfire). Both Jason and I really liked Merkel’s RX Helix. It balances well, the action is smooth, the wood is gorgeous, and the overall design thinking that went into this German-engineered take-down rifle is very impressive. The Helix’s universal-sized action lets you shoot anything from a .222 Rem to a .300 Win Mag with the same gun. And — get this — you can really swap barrels (and change bolt heads) in a couple of minutes with no tools, employing a dead-simple bolt-release lever concealed under the push-button-released removable forearm. (Watch VIDEO BELOW to see Barrel Swap procedure).

Rotary 7-Lug Bolt
While the RX Helix is a straight-pull rifle, it retains the strength and safety of a rotary bolt head with seven locking lugs that seat in a barrel extension. Unlike a Blaser, the RX Helix has a fully-enclosed action housing. That’s an important safety feature. Moreover, since the RX Helix employs a closed action, the bolt body doesn’t travel outside that action. This means the shooter can maintain his cheekweld with an eye on the target as he cycles the bolt.

The RX Helix’s linear (back and forth) bolt-handle motion is transmitted to the bolt head through a 1:2 ratio “transmission” gearing system. This allows smooth and fast cycling without the rotational or tipping movement found on other straight-pull, bolt-action rifles, such as the Blaser.

The Merkel linear-movement action cycles exceptionally fast, which allows for faster follow-up shots — a good thing if you’re hunting dangerous game. The RX Helix features a manual cocking lever on the tang and a direct trigger system. And here’s good news for southpaws — though Merkel does not make a dedicated left-hand version, lefties can very easily use their right hand to work the bolt while maintaining cheekweld. That may sound awkward, but with practice, it’s actually pretty efficient.

Fast, Easy Disassembly and Barrel Exchanges
The video below shows how the Helix can be disassembled (for cleaning or transport) in a matter of seconds WITHOUT TOOLS. The forearm slips off with the push of a button. A short lever on the left side of the action holds the barrel. Simply rotate the lever and the barrel (with bolt head) slips off. That’s it — in 30 seconds the rifle is apart, and you don’t even need an allen wrench as with a Blaser.

The RX Helix has a universal action length that covers calibers from .222 Rem to .300 Win Mag. Changing calibers (or chamberings) takes less than a minute with the appropriate barrel, bolt-head and magazine. Weaver rails are integrated into the action, and iron sights with three-dot rear and one-dot front fiber-optic inserts are standard.

The RX Helix is available with a standard black finish as well as four levels of design — Arabesque, Wild Boar, Spirit, and Deluxe. An all-carbon-fiber version was also available either with or without a carbon-wrapped barrel. The RX Helix comes in a wide range of calibers including .222 Rem, .223 Rem, .243 Win, 6.5×55 SE, .270 Win, 7×64, .308 Win, .30-06 Sprg., 8×57 IS, 9.3×62, 7mm Rem Mag and .300 Win Mag. Barrel lengths vary according to caliber, and barrels, bolt-heads and magazines are available for caliber changes. EuroOptic sells the Merkel RX Helix, but most models are back-ordered.

AIM Field Sports FS-42 Rifle Carry Bag (Shoulder Pack)

Gear Review by Jason Baney
I recently had the opportunity to test out the AIM Field Sports FS-42 rifle carry bag from the UK. This brand, while not well known in the USA, is popular throughout Europe as AIM makes incredibly robust and well thought-out gear. In addition to AIM’s house brand, AIM also sells OEM gear for other well-known companies, so this outfit is well-versed in the market and know what works and what doesn’t. These are incredibly well-made bags at a very fair price (£157.50, about $196.00 USD). I expect we will see more AIM rifle bags come to the U.S. market in the coming years.

About the Rifle — Accuracy International AX in 22 Creedmoor
The rifle in the photos is Jason’s new “Groundhog Laser”, chambered in 22 Creedmoor. Jason reports: “The Accuracy Int’l AX platform lets me swap barrels quickly and the Tangent Theta scope allows quick zero resets when switching barrels. The suppressor is a Silencerco Omega and the scope mount is an ERATAC adjustable. With the 24″ 1:8″-twist Bartlein 5R barrel and a healthy charge of H4350 it runs a 75gr Amax just a touch under 3500 FPS for a 1000-yard come-up of about 5.3 mils!”

Jason added: “Even my 6-year-old son loves to shoot the rifle (with the LOP set at minimum). The boy took the first 7 groundhogs with it over a 2-hour span. I took 4 that day as well — an epic groundhog adventure. My son also recently shot this rifle at 1000 yards. On his very first 1K outing, he went 10 for 11 shots on a 2/3 IPSC target!”

For me, the FS-42 was intended to carry my Accuracy International AX (another fabulous tool from the UK) to and from the range, matches, and groundhog fields. While AIM Field Sports makes several types of Carry Cases and Drag Bags, this FS-42 is the model for right-side folding stock rifles up to a length of about 41.5.” AIM’s FXS-42 would be the choice for similar length rifles but with a butt-stock that folds to the left.

Good Shoulder Strap System Provides Comfortable Carry
The backpack straps received quite a bit of use and are well designed and rugged — you hardly know they exist until you deploy them for use. I actually enjoyed carrying my heavy rifle even when loaded with a tripod (strapped on the external loops), ammo, bipod, mags, suppressor, camera gear and a couple bean bags. It had no problem handling my heavy rifle and gear. Even with a 24″ barrel with suppressor mounted, and large Tangent Theta 5-25 scope the bag had plenty of room to secure and protect it.

The FS-42 gives plenty of room for support gear and has many well placed straps and reinforcements to keep your rifle in place and protected in transit. The more time I spend with it the more features I notice. It is obvious that these bags were designed by shooters. While no soft case/drag bag can quite offer the same protection of a hard case, it is much less cumbersome and holds about the same amount of gear. It is so well thought-out there is even a spot for a cleaning rod along the spine of the case!

Overall, the AIM FS-series bags are well-made, well laid-out and a great value in a world where some similar bags can be nearly twice the cost. These AIM bags are a great alternative to dragging heavy hard cases around.

Final Thought: “The FS-42 Bag is excellent — I dig it. It has worked well for all tasks. The only thing I would change is a bit more padding where the bag lies on your low-back/pelvis area.”

Are you feelin’ lucky? Then enter the latest EuroOptic Rifle Give-Away Contest. At the end of May 2019, EuroOptic will give away a New 6.5 Creedmoor Remington 700 SPS Barreled Action in a Magpul Hunter Stock (value $969.00). The Prize Rifle comes complete with a Steiner Optics H4Xi 4-16x56mm Scope (value $1174.99). Total Prize value is $2143.99!

» CLICK HERE to Enter 6.5 Creedmoor Rifle Contest

6.5 Creedmoor Barreled Action with Magpul Hunter Stock
The Remington 700 SPS 6.5 Creedmoor Barreled Action with Magpul Hunter ODG Stock Kit is a rugged rifle designed for both hunters and precision shooters alike. The classic Rem 700 action paired with this heavy threaded barrel can deliver impressive accuracy with the 6.5 Creedmoor cartridge. The Magpul Hunter Stock offers good ergonomics and functionality while keeping the weight down. SEE Rifle Details HERE.

Steiner H4Xi 4-16×56 LRS Scope
The Steiner H4Xi 4-16x56mm riflescope is a good choice for long-range target shooting and challenging hunting scenarios. The illuminated Steiner Plex-S1 reticle features ballistic lines and crosswind markers for long range accuracy under pressure. The H4Xi’s large objective diameter and superb optical glass present a bright and clear sight picture in most lighting conditions.

For folks in the gun industry, the third Monday in January is the best day of the year. Held in conjunction with SHOT Show, Industry Day at the Range lets us try out dozens of new rifles and pistols, as well as meet top gun designers and friends in the shooting sports. We saw some very great new products this year. Here are some of the most interesting “take-aways” from Industry Day at the Range, held in Bolder City, Nevada on January 21, 2019.

New Guns + Old Friends
Meeting old friends, and shooting new guns. That’s what Monday was all about at the annual Industry Day at the Range, a “hands-on” preview the day before SHOT Show opens in Las Vegas. Your Editor met with old buddy Jason Baney and Hunting Editor Colton Reid at the crack of dawn and headed out to the Boulder City (NV) range.

We were not disappointed — there was plenty to see this year. On display were a bunch of new precision rifles, a slew of new handguns, and some very exotic optics (including a turretless digital camera/riflesight).

Cool New Rifles and Chassis Systems

Our friend Stan Pate let us try out Savage’s latest, greatest Modern Sporting Rifle, the MSR 10 Precision. Offered in 6mm Creedmoor, 6.5 Creedmoor, and .308 Win, this quality rig has many distinctive features, including side-charging handle, adjustable gas system, and convertible dual-angle pistol grip. This rifle proved exceptionally accurate on steel out to 400 yards. It is certainly one of the best AR10-class rifles we’ve tried.

Report from 6.5 Guys
Our good friends the 6.5 Guys (www.65guys.com) kicked off their 5th year of SHOT Show coverage at the Industry Day at the Range. At this event one can check out the latest firearms, putting guns through their paces with live fire demos. Here are two items that caught the eyes of the 6.5 Guys:

PGW Defense Timberwolf

The PGW Defense Timberwolf rifle in .338 Lapua Magnum proved to be a relatively light-recoiling rifle considering the cartridge and overall rifle weight of 14.5 pounds. Even with gusting 7:00 o’clock side winds (with 20+ mph peaks), hitting targets at 1,000 yards was very doable — a reminder of what the .338 Lapua can deliver. Impressive rifle.

Oryx Chassis for Howa, Rem, Tikka, Ruger, and Savage

Oryx (an MDT brand) has introduced a chassis system for Howa, Remington, Tikka, Ruger and Savage actions that retails for $399. While it comes with a grip, the user can bolt on standard AR-15 grips. This affordable system comes with an adjustable cheek piece and length of pull.

Industry Day file photo courtesy CMG Marketing & Events.

Optics — New 7-35x56mm Leupold + Radical Israeli Sensight

Leupold showcased an impressive new scope that should interest F-Class and PRS shooters. Leupold’s new 7-35x56mm Mark 5HD optic had very good glass, and positive controls. At 33 ounces, it is quite a bit lighter than other scopes in this class. We don’t have exact pricing yet, but it should be much less expensive than a Nightforce ATACR scope with the same magnification range.

New Leupold 7-35x56mm Mark 5HD

The new 7-35X Leupold models will be available with either milrad or MOA adjustments and advanced reticles. The milliradian models will be available in six reticle options: H-59, CCH, TMR, Tremor 3, and Tremor 3 Illuminated. The MOA version will be available with an Impact 60 MOA reticle.

Sensight SSR400 digital Riflesight

A big step forward in digital optics is Sensight’s new SSR400 Digital Riflesight, basically a high-resolution digital camera with a microprocessor-controlled reticle. The system is self-contained in a lightweight, compact display that allows the firearm to be held and used as if it held a traditional rifle scope. The digital interface allows users to customize the display, record video, and even livestream the image. The display eliminates eye relief issues, making it easy to acquire targets at distances up to 400 yards. Beyond 400 yards the image becomes noticeably pixelated, but still allowed us to easily hit targets at that distance. The price is moderate.

Read Detailed Sensight SSR400 REVIEW on GunsAmerica.com »

Handguns — Rimfire and Centerfire

We viewed hundreds of pistols, shot a dozen or so, and came away with four we really liked. Two were suppressed rimfire pistols, and two were centerfire “Race guns”.

Ruger .22 LR MARK IV 22/25 Gold With Suppressor

We had fun trying out the Ruger MARK IV™ 22/45™ LITE fitted with a factory suppressor. Ruger had a new “bling” version on hand for test shooting. This was the Model 43926, with gold anodized aluminum upper receiver. This is ported for lightness — this pistol weighs just 25 ounces (without suppressor).

KelTec CP33 Suppressed Rimfire Pistol

We shot a very impressive KelTec pistol derived from the KelTec CMR-30 .22 WMR carbine. This new CP33 pistol is mostly the same as the CMR-30, but with no stock and a different front section. The 33 in the name refers to the fact that the clear magazine holds 33 rounds of .22 LR ammo. The version we shot was suppressed, and it was a pleasure to shoot. The trigger is excellent — noticeably better than most other 22s on the market. With virtually no recoil, it was ultra-quiet and surprisingly accurate. This Editor was surprised that a KelTec was one of his favorite new handguns at Industry Day. KelTec says the first production run should start shipping in March, 2019.

Walther PPQ Q5 Match SF (Steel Frame)

Walther’s PPQ Q5 has been popular with action pistol competitors. Now Walther offers an enhanced SF (“Steel Frame”) version. We like how the pistol balances with the heavier, beefier steel frame. We expect the extra mass of the steel frame will also reduce muzzle flip and perceived recoil. This is available from Walther with iron sights or a Red Dot.

Bul Armory SAS 1911-Type Race Gun

Israel’s Bul Armory offers a wide range of defensive handguns and target pistols, including the SAS series of competition pistols. These impressive “Race Guns” feature compensators, relieved slides, flared magwells, and excellent match triggers. Needless to say these comp pistols are a hoot to shot — with superfast cycle rates for fast shot transitions.

Industry Day file photo courtesy CMG Marketing & Events.

Ammunition — Big News from Sierra and More

Sierra Will Offer Loaded Ammunition
The big news in the world of commercial ammunitions come from Sierra bullets. For the first time, Sierra will be offering Sierra-branded loaded ammo. Our good friend (and multi-time Nat’l Long Range Champion) Michelle Gallagher revealed that Sierra will offer a selection of high-quality factory ammunition in 2019.

Sierra will be releasing its own brand of hunting ammunition. Sierra “Gamechanger” will debut in five popular hunting calibers: .243 Win, 6mm Creedmoor, 6.5 Creedmoor, .270 Win, and .308 Win. The rounds use a new tipped GameKing bullet for match grade accuracy in a hunting round. No details yet on brass, primer, and powder components for this ammo, but if the quality of the bullets is any indication these rounds will serve hunters well.

New Norma Monolithic Hollow Point Ammo
Norma unveiled some impressive new pistol ammunition. The new MHP (Monolithic Hollow Point) offers extreme expansion with major energy transfer. This MHP bullet features a lead-free solid core. This new MHP ammo offers serious performance for regions where lead-core bullets are prohibited. Accuracy is also very good with these new Norma bullets.

Great Products for Hunters and Varminters

We saw some impressive gear for game hunters and varminters. Swagger bipods has introduced a new kind of rifle support that combines the best qualities of both a field bipod and shooting sticks. And we saw a nice swivel field bench that offered very good stability.

Swagger demonstrated its new Stalker QD42 (quick detach) and Stalker Lite bipods. The QD42 is a lighter, more compact design of the already-established hunter series that allows for fast attach and removal via the push of a button. The quick attach/detach is a great feature that allows hunters to carry the bipod in their pack until it’s time to shoot. The Stalker Lite offers similar advantages in that it is extremely light and folds up like tent poles so it can be carried in a pack or side pocket. Both systems demonstrate the maneuverability swagger is known for and are reasonably priced.

Many Industry Day exhibitors were using the well-made and versatile DOA Shooting Bench. These benches feature a strong steel base supporting a very stable top that rotates to change rifle aim points in seconds. In addition, the DOA bench features a swivel seat. We liked the build quality on these DOA benches. Varmint hunters would like this bench — it would work well in a prairie dog field.

About Industry Day and the Range

With two dozen shooting bays, plus an elevated shooting station with targets out to 400 yards, there is plenty of action. Here’s the layout:

We definitely need to remember why we are able to continue to own and shoot firearms in this nation…

Next best thing to being there — this 5-minute video, produced last year, shows Industry Day highlights. It’s a great overview featuring a wide variety of rifles, pistols and shotguns. The biggest commercial, hands-on “live fire” gun demonstration in the world, Industry Day at the Range is attended by over 1700 journalists and buyers.

For folks in the gun industry, the third Monday in January is the best day of the year. Held in conjunction with SHOT Show, Industry Day at the Range lets us try out dozens of new rifles and pistols, as well as meet top gun designers and friends in the shooting sports. We saw some very great new products this year. Here are some of the most interesting “take-aways” from Industry Day at the Range, held in Bolder City, Nevada on January 22, 2018.

New Guns + Old Friends
Meeting old friends, and shooting new guns. That’s what Monday was all about at the annual Industry Day at the Range, a “hands-on” preview the day before SHOT Show opens in Las Vegas. Your Editor met with old buddy Jason Baney at the crack of dawn and headed out to the Boulder City (NV) range.

We were not disappointed — there was plenty to see this year. On display were a bunch of new precision rifles, a slew of new handguns, and some very exotic optics.

Most Interesting New Rifles

Tikka T1x — Tikka’s New Rimfire Rifle is a Winner

The new Tikka T1x doesn’t disappoint. The bolt operates smoothly. The action feels solid and refined — like a good centerfire action. The trigger is excellent — it breaks cleanly with no creep or grittiness, and we’re told it can be easily adjusted below 2 pounds pull weight. The stock has a good feel in the hand and doesn’t flex — unlike some cheap Tupperware stocks you’ll find on some domestic rimfires. In addition, the action has the same footprint as the Tikka T3, so you can swap this .22 LR action into any stock that fits a T3. Overall this was the single rifle this Editor shot on Industry Day that I would really want to own.

Ruger Precision Rimfire — Baby Brother to the Ruger Precision Rifle

We test-fired the new Ruger Precision Rimfire. Unfortunately, with the wobbly setup and no paper targets, we could not really evaluate accuracy. Function is good, but we couldn’t call the bolt movement smooth. The trigger is not bad. Most of the chassis from the handguard rearward is reinforced polymer so the gun is pretty light. The + 30 MOA Picatinny rail is nice.

Above you can see the Ruger Precision Rimfire with its big centerfire brother, the Ruger Precision Rifle. Initial reports say that Ruger’s new rimfire rifle shoots well with affordable .22 LR ammo. Here’s a report from Forum Member RICHK: “Took mine to the range today, and ran eight (8) brands of ammo through it. Three worked really well. The best, Federal Match 22, shot .145 inch groups at 50 yards. Fine rifle.”

SAKO TRG 42 A-1 in .338 Lapua Magnum

Here is a handsome, beautifully-machined big-bore tactical rifle with all the bells and whistles. Firing from a high-tech tripod with Crux Ordnance rifle mount, our buddy Jason drilled steel at 500+ yards with the big .338 Lapua Magnum Sako. It’s awfully nice when you don’t have to pay for the ammo and they don’t mind if you take home the superb Lapua brass. This is a high end rig for serious engagements.

Savage Model 110 Line with AccuFit Comb and Buttpad Inserts

Savage showed off its new-for-2018 Model 110 Line-Up with the new Accufit system of cheekpiece/buttpad extensions that allow shooters to customize comb height and LOP. But, we were more interested in what you can’t see — the new internal aluminum chassis.

As part of Savage’s new Accustock system, a long aluminum sub-chassis serves as a bedding block for the action and provides general stiffening for the stock. That’s smart engineering. This video shows how the Savage internal chassis works. We highly recommend you watch this video:

Ritter & Stark SX-1 Modular Tactical Rifle

We liked the new Ritter and Stark Rifle SX-1 Modular Tactical Rifle from Germany. Fit and finish is very good. This is an honest competitor to the Accuracy International rifles. This rig is designed to allow rapid barrel changes for three chamberings: .308 Winchester, .300 Winchester Magnum, and .338 Lapua Magnum. Ergonomics were good — the grip was comfortable and we like the fact that the butt adjusts for vertical position. Notably, the scope rail is mounted on the barrel itself, and the bolt locks directly into the barrel. This patented system allows scope, rail, and barrel to be swapped out as one integrated assembly, which should definitely help maintain zero when barrels are exchanged.

Kriss Vector SBR — Full-Auto Fun and Firepower

We got a chance to shoot the 9x19mm version of the Kriss Vector Gen II SBR (Short Barrel Rifle) in FDE (Flat Dark Earth). This is a full-auto, pistol cartridge short-barrel rifle that uses Glock mags. It has a handy fire control selector so you can shoot it in single-shot, two-shot, or full-auto modes. This was a hoot to shoot. We’ve shot full-auto 9mm Uzi subguns in the past and this Kriss was easier to hold on target (and more accurate). Recoil was negligible. This is offered in four calibers: .357 Sig, 9x19mm, 10mm, and .45 ACP. MSRP is $1569.00, but civilians can’t buy this.

Best New Handguns

We viewed hundreds of pistols, shot a dozen or so, and came away with three we really liked. Here is a stunningly expensive 1911-type STI race gun, a handsome new 9mm Kimber, and a very innovative new polymer pistol from Europe, the Archon Type B.

STI 2011 DVC Open Race Gun — Four Grand Worth of Zing and Bling

At $3999.00, this is probably the most expensive comp pistol we’ve ever seen. This STI 2011 DVC Open features a host of “go-fast” features including relieved slide, gold-tone TiN barrel with extended compensator, over-size Dawson Precision Magwell, mounted C-More 8-MOA optic, and a special lever for fast slide racking. If you want to win, this might be a good investment, but this Editor kept thinking “this pistol costs more than my car is worth…”

Kimber Aegis Pro 9mm with 4″ Barrel

This is a 1911-style pistol with some interesting features. It combines a full-size bobtail frame with a shorter 4″ barrel. This makes the gun balance very nicely and it’s a bit more compact for carry. The trigger pull was outstanding, and recoil was mild with the 9mm Luger chambering, so this gun was a pleasure to shoot. This Editor would like to have one of these. The slide is machined to fit a Red Dot sight. For gun games and action pistol comps, the Red Dot really speeds up the aiming process.

Archon Firearms Type B with Ultra-Low Bore Axis

Developed in Italy, Made in Germany, and backed by the big RUAG company, the new Archon Type B 9mm pistol is one of the most innovative semi-auto handguns we’ve seen in years. The Type B boasts a patented barrel system. It is not the classic Browning tilting barrel. The Type B’s barrel is not fixed; however, it moves only a few millimeters up and back as the slide retracts. That barrel geometry allows the slide to be exceptionally low. And the frame design puts the web of your hand up high. Those design features really do help tame perceived muzzle lift. This gun was easy to shoot, and the sights came back on target very quickly.

Trends in Ammunition

On Industry Day at the Range, all ammo is free. So you can shoot to your heart’s content without worrying about cost (or picking up your brass). This year we noted that many gun-makers supplied Federal Syntec ammo with distinctive red, polymer-encapsulated bullets. The polymer coating cuts barrel fouling, and also reduces ricochets and “splashback” on steel targets:

Winchester also unveiled an interesting line of Hybrid-X ammunition. This has a dual-element bullet. The rear section of the bullet is jacketed with a heavy element core. The front half of the bullet has a shaped, polymer matrix cone. This hybrid design offers improved penetration PLUS greater energy delivery inside the target as the bullet separates into multiple elements. You can see how this works in the Ballistic Gelatin photo below.

Suppressor Tech: Integrally Suppressed Rifle Barrels

Suppressed Weapon Systems (SWS) had a rack of rifles with very fat barrels — barrels that served double duty. These barrels are, effectively, extremely long suppressors. The conventional barrel unit is combined with a full-length sound moderator, offering exceptional noise reduction. In the photo above, every rifle in the front side of the rack has an SWS integral suppressor/barrel system. This is interesting technology.

With two dozen shooting bays, plus an elevated shooting station with targets out to 400 yards, there is plenty of action. Here’s the layout:

Next best thing to being there — this 5-minute video, filmed in 2015-16, shows all the activities on Media Day at the Boulder Rifle and Pistol Club. It’s a great overview of the event where over 1700 media members and buyers gather to test and evaluate the latest (and greatest) guns and shooting accessories introductions from over 200 manufacturers.

If you need a high-quality scope for your hunting rifle, here are some exceptional deals on premium European-designed optics from Leica, a world leader in optics technology. Right now at EuroOptic.com you can get top-quality Leica ER5 riflescopes for 50% off. For example the ER5 2-10x50mm scope with Plex reticle, normally $999.00 is now priced at just $499.00. CLICK HERE for ER5 Product Specs.

These Leica prices are so LOW and the scopes are selling so fast we wanted to let you guys know. Jason Baney helped get this site off the ground a decade ago (when we were 6mmBR.com). Now Jason works at EuroOptic.com. He called to let us know about this special sale on Leica hunting scopes.

Jason notes: “FYI, these are MADE-IN-USA and the turrets under the caps are appropriately marked and finger-adjustable to be able to dial up in the field. Also you can reset the zero on the turret by just lifting to disengage and then push it back down to lock in — very slick”. Learn More HERE.

Available models on sale are: ER5 2-10x50mm (4 reticles); ER5 3-15x56mm (4 reticles); ER5 4-20x50mm (2 reticles)

Gear Review by GS Arizona

This article originally appeared in the Rifleman’s Journal website.
Many of you have doubtlessly read Bryan Litz’s articles in our Daily Bulletin and on his Applied Ballistics website about various current long-range bullets. Bryan’s work carries a great deal of weight in the world of ballistics, so his comments (and mathematical proofs) regarding the benefits of bullet pointing certainly caught my attention. Bullet pointing, like meplat trimming, is an effort to reduce the ballistic inconsistency created by the somewhat jagged tip of the jacket where the bullet forming dies bring it to a point in the manufacturing process. Of course, we could eliminate this problem altogether by shooting closed-tip, open-base bullets like the Lapua D46, but that merely shifts the jacket problem to the other end of the bullet.

In any event, hollow point bullets rule the accuracy world today, so John Whidden, multi-time National Long Range Champion and a talented gunsmith to boot, came up with a very handy tool to let us make those hollow points pointier. Let’s have a look at John’s tool and see how it works.

The Whidden Bullet Pointing Die System uses a Forster bullet seating die body as its basic structure and that’s a good choice given the quality machining Forster does on these. The real heart of the tool comes in two parts: the caliber sleeve and the pointing die that fits inside the sleeve. In fact, to point up different caliber bullets, you only need to change the caliber sleeve, everything else remains the same. The last item is the bullet base that slips into a standard .308 shellholder and supports the bullet as it goes into the die body.

It took me less than five minutes to get everything set up, including changing the caliber sleeve from 6mm to .30 caliber. John’s instruction sheets are well illustrated and clearly written; you should have no problem getting up and running.

Pointing the bullets is as easy as sizing a piece of brass. You can see in the second photo above the difference between a few pointed bullets and a few un-pointed ones. The innermost pointed bullet in the picture was my first attempt and I adjusted the die a little after that, you can see that the others are closed a little more. John even includes a couple of sample bullets so that you can see one done right and one done wrong. That is a nice addition that can help you achieve the desired results.

This YouTube Video Shows the Whidden Bullet Pointing Die in Action

I think Bryan’s work supports the validity of this concept and John’s tool puts it into practice in a simple-to-use manner that makes it just about impossible to do any damage to the bullet. I have shot pointed bullets in various calibers at many matches now. Pointing is not a “miracle cure”, but I believe that pointing bullet tips can produce long-range accuracy gains, through reduced vertical dispersion, for many popular types of match bullets. The Whidden Bullet Pointing Die System retails for $220.00 (with one insert). Additional die inserts are $42.00 each. Extra caliber sleeves are also $42.00. You can purchase directly from Whidden Gunworks, or from Sinclair International.