Readers often ask “What’s the difference between a Weaver scope rail and a Picatinny Rail?” The answer is not as simple as it seems. The dimensions of a Picatinny Rail should be consistent (from one rail-maker to another), since there IS a government spec. Conversely, there is some variance in “Weaver-style” rails. The width of the groove is the most important difference between Picatinny Rails and Weaver-type rails. “Mil-spec” Picatinny rails will have a grove width of 0.206″ while Weaver rails typically have a narrower, 0.180″ groove width.

Does your rifle have a Weaver Rail or Picatinny Rail? Check the dimensions to be sure.

A while back, Brownells had a helpful GunTech™ Article that discussed the Picatinny Rail vs. Weaver Rail. That article explained:

What are the differences between the ‘Picatinny’ and the ‘Weaver’ systems? The profile of the two systems is virtually identical. Depending on the quality of the machining done by the manufacturer, the two systems should be indistinguishable from the profile. The key difference lies in the placement of the recoil grooves and with width of the grooves. MIL-STD-1913 (Picatinny) grooves are .206″ wide and have a center-to-center width of .394”. The placement of these grooves has to be consistent in order for it to be a true Picatinny MIL-STD system. Weaver systems have a .180” width of recoil groove and are not necessarily consistent in a center-to-center measurement from one groove to the next.

In many instances, a Weaver system has a specific application that it is machined for, so interchangeability is not necessarily an issue. A MIL-STD-1913 system must adhere to the specifications listed above in order for it to be considered MIL-STD, since the military desires uniformity in the recoil grooves to allow for different systems to be mounted on the weapon with no concern for compatibility.

Now, what does this mean? Boiled down, it means that accessories designed for a Weaver system will, in most cases, fit on a Picatinny system. The reverse, however, is probably not the case. Due to the larger recoil groove, Picatinny accessories will not fit a Weaver system. There are, of course, exceptions to every rule, but for a good rule-of-thumb, [full-width] Picatinny won’t fit Weaver, but Weaver accessories WILL fit Picatinny.

Readers often ask “What’s the difference between a Weaver scope rail and a Picatinny Rail?” The answer is not as simple as it seems. The dimensions of a Picatinny Rail should be consistent (from one rail-maker to another), since there IS a government spec. Conversely, there is some variance in “Weaver-style” rails. The width of the groove is the most important difference between Picatinny Rails and Weaver-type rails. “Mil-spec” Picatinny rails will have a grove width of 0.206″ while Weaver rails typically have a narrower, 0.180″ groove width.

Does your rifle have a Weaver Rail or Picatinny Rail? Check the dimensions to be sure.

A while back, Brownells had a helpful GunTech™ Article that discussed the Picatinny Rail vs. Weaver Rail. That article explained:

What are the differences between the ‘Picatinny’ and the ‘Weaver’ systems? The profile of the two systems is virtually identical. Depending on the quality of the machining done by the manufacturer, the two systems should be indistinguishable from the profile. The key difference lies in the placement of the recoil grooves and with width of the grooves. MIL-STD-1913 (Picatinny) grooves are .206″ wide and have a center-to-center width of .394”. The placement of these grooves has to be consistent in order for it to be a true Picatinny MIL-STD system. Weaver systems have a .180” width of recoil groove and are not necessarily consistent in a center-to-center measurement from one groove to the next.

In many instances, a Weaver system has a specific application that it is machined for, so interchangeability is not necessarily an issue. A MIL-STD-1913 system must adhere to the specifications listed above in order for it to be considered MIL-STD, since the military desires uniformity in the recoil grooves to allow for different systems to be mounted on the weapon with no concern for compatibility.

Now, what does this mean? Boiled down, it means that accessories designed for a Weaver system will, in most cases, fit on a Picatinny system. The reverse, however, is probably not the case. Due to the larger recoil groove, Picatinny accessories will not fit a Weaver system. There are, of course, exceptions to every rule, but for a good rule-of-thumb, [full-width] Picatinny won’t fit Weaver, but Weaver accessories WILL fit Picatinny.

Readers often ask “What’s the difference between a Weaver scope rail and a Picatinny Rail?” The answer is not as simple as it seems. The dimensions of a Picatinny Rail should be consistent (from one rail-maker to another), since there IS a government spec. Conversely, there is some variance in “Weaver-style” rails. The width of the groove is the most important difference between Picatinny Rails and Weaver-type rails. “Mil-spec” Picatinny rails will have a grove width of 0.206″ while Weaver rails typically have a narrower, 0.180″ groove width.

Does your rifle have a Weaver Rail or Picatinny Rail? Check the dimensions to be sure.

Brownell’s has a helpful GunTech™ Article that discusses the Picatinny Rail vs. Weaver Rail. That article explains:

What are the differences between the ‘Picatinny’ and the ‘Weaver’ systems? The profile of the two systems is virtually identical. Depending on the quality of the machining done by the manufacturer, the two systems should be indistinguishable from the profile. The key difference lies in the placement of the recoil grooves and with width of the grooves. MIL-STD-1913 (Picatinny) grooves are .206″ wide and have a center-to-center width of .394”. The placement of these grooves has to be consistent in order for it to be a true Picatinny MIL-STD system. Weaver systems have a .180” width of recoil groove and are not necessarily consistent in a center-to-center measurement from one groove to the next.

In many instances, a Weaver system has a specific application that it is machined for, so interchangeability is not necessarily an issue. A MIL-STD-1913 system must adhere to the specifications listed above in order for it to be considered MIL-STD, since the military desires uniformity in the recoil grooves to allow for different systems to be mounted on the weapon with no concern for compatibility.

Now, what does this mean? Boiled down, it means that accessories designed for a Weaver system will, in most cases, fit on a Picatinny system. The reverse, however, is probably not the case. Due to the larger recoil groove, Picatinny accessories will not fit a Weaver system. There are, of course, exceptions to every rule, but for a good rule-of-thumb, [full-width] Picatinny won’t fit Weaver, but Weaver accessories WILL fit Picatinny.

Here’s a cleverly-designed product that adds versatility to any rifle with a front sling swivel stud. This clever Stud Rail Adapter (SRA) allows you to mount a Picatinny Rail on a sling swivel stud. With the SRA in place, you can attach any accessories that clamp to a Pic rail, such as lights, lasers, pistol grips, or rail-affixed tactical bipods. And look carefully — the SRA’s designers included a sling swivel at the inboard end of the unit. That way you can mount Picatinny-rail accessories and still use your carry sling.

Sold by Harrisbipods.com, the SRA Stud Rail Adapter retails for $47.85. This adapter is crafted in the USA by MIM Mfg. from 6061 TG Aluminum with a black anodized finish. This can be used with the RBA-1 and RBA-2 bipod adapters.

This adapter is a useful invention, particularly for those who might want to mount a light or clamp-on bipod to a varmint rifle. Most hunting rifles have a front sling swivel stud and there is now a very wide selection of Picatinny-rail-mounted accessories.

NOTE: HarrisBipods.com is a web retailer. This is NOT Harris Engineering, the manufacturer of Harris bipods. HarrisBipods.com does sell the full line of Harris bipods and most Harris accessories.

Leveling your scope can be a time-consuming and tedious process. The Fix It Sticks folks have changed that with the introduction of the Scope Jack. This simple unit levels a scope through contact with the flat on the bottom of the scope (opposite the elevation knob). You can do this quickly, with one hand, leaving the other free to tighten your rings once the scope is aligned. This really is a clever, effective, easy-to-use tool, as you can see in this video:

You attach the Scope Jack to the Picatinny rail on your rifle, then lossen the rings so the scope can rotate. Then simply elevate the Scope Jack with a quick twist, using a 1/4″ driver. The Scope Jack’s horizontal roller will contact the scope’s bottom flat, rotating the scope it into proper alignment, square to the rail.

Operating Instructions from Manufacturer Fix It Sticks
The Scope Jack works with any 1/4 inch driver to quickly and easily level your scope to your rail. Just mount the scope jack to the pic rail under your scope and turn the drive handle until the lifting arm engages with the flat section under your turrets. Once the scope is level, maintain pressure while tightening your ring screws to keep optic level throughout the process.

Requirements:
1. Scope much have a central flat section under turrets
2. Needs a minimum of 1/4″ clearance between rail and scope
3. Picatinny Rail must be accessible under optic

TECH TIP: You Still Must Check the Reticle Orientation INSIDE Your Scope
The Scope Jack works fast, but it is NOT the “final solution”. Why? Some scopes have a reticle that is not perfectly aligned with the turrets and/or bottom flat. We have seen scopes with vertical reticle line off as much as three degrees (3 °) from true plumb. With such a scope, you CAN set the reticle square, but then your turrets will be canted relative to the receiver. That creates issues when shooting at long range. Accordingly, if your scope has a badly canted reticle, you should send it back to the manufacture for warranty repair. Three degrees may not sound like much, but it is actually quite noticeable:

For all scopes, AFTER using the Scope Jack, we recommend you test your reticle with a plumb line. You can hang this line from a door or ceiling fixture with a weight on the bottom. Important — when using a plumb line make sure your rifle is 100% level or your results may be off. We recommend using a bubble level to help align your rifle properly.

SilencerCo has introduced a new laser rangefinder (LRF) that mounts directly on a rifle. The new Radius rangefinder can attach to a standard Picatinny rail in any orientation. Windage and elevation controls allow the Radius be precisely aligned with your scope. This way you can place your scope’s cross hair on a target and instantly get a range at the push of a button. The Radius even includes a visible laser to help align the LRF with your riflescope.

The ability to collimate (align) your rangefinder with your optic should be a boon to varmint hunters and tactical shooters. A varmint hunter in a prairie dog field can quickly range a dog mound as he scans the field for critters. A tactical competitor can get target range the instant he sees his target in his scope.

With a $999 MSRP, the compact Radius rangefinder features a user-configurable display, long battery life, and extreme durability. It also has a “scan” capability that allows you to range multiple targets quickly. The Radius was developed by SilencerCo Weapons Research (SWR), a new R&D division of SilencerCo. The Radius starts shipping in October 2015.

SilencerCo Radius LRF Mounted on side Picatinny rail. Image from SnipersHide Product Preview Video.

Also from SilencerCo — 9mm Pistol with Built-in Suppressor
At a product launch this week, SilencerCo also unveiled its new Maxim 9 silenced pistol. This integrally-suppressed, semi-automatic 9x19mm pistol is ergonomic and holsterable. SilencerCo claims the new Maxim 9 is “hearing-safe” with factory ammo. Accordingly, the manufacturer says: “the Maxim 9 will forever change the way people think about firearms as they realize that there is no longer any reason why guns have to be loud.” Report by Chris Cheng.

Sold by Harrisbipods.com, the SRA Stud Rail Adapter retails for $47.85. NOTE: HarrisBipods.com is a web retailer. This is NOT Harris Engineering, the manufacturer of Harris bipods. HarrisBipods.com does sell the full line of Harris bipods and most Harris accessories. However, as far as we can tell the SRA is NOT made by Harris Engineering.

Comment: We think this adapter is a useful invention, particularly for those who might want to mount a light to a varmint rifle. Most hunting rifles have a front sling swivel stud and there is now a very wide selection of Picatinny-rail-mounted accessories.

The .223 Scout Rifle is offered in both right- and left-hand versions, both with a 10-round detachable box magazine. You can choose either an all-stainless version ($1099.00 MSRP), with SS receiver and SS barrel, or a dark version ($1039.00 MSRP) with matte black alloy steel action and barrel. The bolt offers Mauser-style controlled round feed, with a lever-style safety on the rear of the bolt shroud. The rifle features a 16.1″, 1:8″-twist rate, barrel fitted with flash hider which can be removed to attach other 1/2-28 threaded barrel accessories. Interestingly, the magazine for .223/5.56 Scout Rifle is dimensionally the same as the mag for the .308 Scout Rifle. The .223/5.56 mag employs a plastic insert to feed the smaller cartridge properly.

American Rifleman Field Test of .223 Rem Scout Rifle

Adjustable Length of Pull Through Buttpad Spacers
The black laminate stock is fitted with sling swivel studs and features checkered grip and forearm. A soft rubber recoil pad with three 1/2″ spacers allows the length of pull (LOP) to be adjusted.

Ruger Scout Rifles feature a Mini-14-style protected, non-glare, post front sight and receiver-mounted, adjustable, ghost ring rear sight. The forward-mounted Picatinny rail lets you use a variety of optics including LER scout scopes that allow “both eyes open” target acquisition. Ruger provides scope rings for mounting conventional scopes on the integral M77-style mounts built into the Scout Rifle receivers.

We like the quick-detach feature. This lets you quickly check and/or clear your chamber, or inspect the bolt. The bag itself, made from heat-resistant mesh fabric, will hold approximately one hundred .223 Rem cartridge cases. And here’s another nice feature — the bag has a zipper on the bottom so you can quickly dump your spent brass without having to remove the brass-catcher from your rifle.

If you shoot an AR and reload your own ammo, you should get some kind of brass-catching device. With a $39.19 “street price” ($49.99 MSRP), this is one of the more affordable options. Once you use a rig like this and no longer have to pick up brass from the ground, you may get spoiled. Moreover, a brass-catcher like this will earn you “Brownie Points” with other shooters at your range who no longer have to dodge your hot brass.

These Warne integrated ring/mount sets are offered for 1″, 30mm, and 34mm rings. The 1″ and 30mm versions come in all four (4) colors and cost $87.95. The 34mm is offered in Matte Black only for $115.00. You may want to order soon. These are popular. The most popular colors (black and dark earth) could sell out quickly at this price.