Smith & Wesson (S&W) is recalling ALL M&P 12 Shotguns manufactured before 10/15/2021 due to concerns over cracked barrels, which could cause serious safety issues. If you own one of these newly introduced bullpup shotguns, you should check the serial number, and send the M&P 12 back to S&W for repair. S&W will pay for shipping. For more information go to MPshotgunrecall.com.

PRODUCTS AFFECTED:
This notice applies to M&P12 Shotguns manufactured prior to October 15, 2021. To determine whether your M&P12 Shotgun is affected, check the label on the box to determine the date of manufacture. If the manufacture date is prior to October 15, 2021, your shotgun is subject to this Recall and should be returned to Smith & Wesson for inspection. If you are unsure of the date of manufacture, input the serial number on the S&W Website Recall Page, or call 833-957-3476.

REMEDY/ACTION TO BE TAKEN:
If your Shotgun was manufactured prior to October 15, 2021, please call 833-957-3476 to obtain a pre-paid return label, to arrange for the return of your Shotgun to Smith & Wesson for inspection. If the barrel from your Shotgun is affected, it will be replaced at no cost to you. All shipping and replacement costs will be covered by Smith & Wesson.

OK guys — check your powder stashes. Here’s an important notice regarding Accurate 2520 powder. There is one lot of Accurate 2520 that is dangerous, so you should not load with it. If you have some of this powder from Lot 0913192116, stop using it, and contact Western Powders at 406-234-0422. Western Powders issued this notice on 7/1/2020:

ACCURATE 2520 RECALL — 2520 Powder — LOT 0913192116
Western Powders is issuing a recall of Accurate 2520 1 lb. bottles with lot number 0913192116. The lot number is stamped on the back of the bottle. This is a limited recall and ONLY applies to this lot number of Accurate 2520. USE OF THIS POWDER MAY RESULT IN HIGH PRESSURE LOADS AND SUBSEQUENT GUN DAMAGE OR SERIOUS PERSONAL INJURY. If you are in possession of this propellant, please discontinue use immediately and contact Western Powders at 406-234-0422. We will replace your powder and instruct you how to dispose of this powder.

Date of Notice: July 1, 2020

Smith & Wesson has issued a CONSUMER SAFETY ALERT for the M&P 15-22, a semi-auto .22LR rimfire rifle with ergonomics like the centerfire AR15. If you own an M&P 15-22, you need to inspect the bolt. A manufacturing problem with the bolt could allow the gun to fire when the bolt closes, even without pulling the trigger. This inspection process is described in this video.

Smith & Wesson states: “The bolt from your M&P 15-22 must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions provided here. We are asking consumers of all M&P 15-22 firearms manufactured before February 1, 2019 to inspect their bolt for this condition.”

Smith & Wesson Notice:
M&P 15-22 CONSUMER SAFETY ALERT
AND INSPECTION PROCEDURE

PRODUCT AFFECTED: ALL models of M&P15-22 rifles and pistols manufactured before February 1, 2019.

STOP USING YOUR M&P 15-22 UNTIL IT HAS BEEN INSPECTED AND YOUR BOLT REPLACED (IF NECESSARY).

Smith & Wesson has identified two M&P 15-22 firearms from recent production on which the breech face counter bore depth was not within manufacturing specification. In those firearms, the lack of depth may allow the bolt, upon closing, to crush the rim of the case, causing the round to fire, cycling the bolt, and potentially resulting in multiple discharges without depressing the trigger. This issue can occur in the following two scenarios:

1) With a loaded magazine in the firearm and the bolt locked to the rear, depressing the bolt release to allow the bolt to drop freely may ignite the round as the bolt closes without engaging the trigger and with the safety selector in either the safe or the fire position, and may also result in multiple discharges.

2) With a loaded magazine in the firearm, bolt in the closed position and a round in the chamber and the safety selector in the fire position, depressing the trigger will cause the round to fire normally, however as the bolt cycles, the next round may be ignited by the bolt crushing the rim of the case as it closes, causing multiple discharges.

We believe that these are isolated incidents, however, any unintended discharge of a firearm has the potential to cause injury. Therefore, we have developed this inspection procedure to ensure that all products in the field are safe to use. We are asking customers to perform the following procedure and to refrain from using their M&P15-22 until the bolt has been inspected and replaced as necessary.

REMEDY/ACTION TO BE TAKEN: The bolt from your M&P15-22 must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions provided here.

Safety Alert Tip from EdLongrange. We welcome reader submissions.

Here is an important safety notice regarding Ramshot Hunter reloading powder. If you have any Ramshot Hunter powder with lot number 489, you should stop using it immediately. If you have loaded ammo with Hunter Powder lot number 489 you should NOT SHOOT this ammo. Use of this powder can result in HIGH PRESSURE loads that can cause injury or damage to your guns.

You can find the lot number on the rear of the package. This make appear one of two ways (see illustration). The lot number 489 may appear above code 080516 or as a long code 080516489.

If you have any lot number 489 Hunter powder, contact Western Powder by telephone at (406) 234-0422. The company will replace your powder for free with an approved lot of Ramshot Hunter.

Recalled Lot Numbers: 3101327, 3110256, 3110683, 3110695, 3110945, 3111388, 3111885. The Lot number can be found printed on the lower portion of the box label.

If you own any of these Lot numbers or have any questions regarding this recall, Call Hornady at 800-338-1242 right away. Hornady Manufacturing Company will make all arrangements associated with the return and replacement of this product.