For years we have touted the advantages of Burris Signature rings, with polymer Pos-Align Inserts. PRS/NRL shooters take note — this technology is available in a beefier, heavy-duty ring system for tactical rifles. The impressive Burris XTR Signature Rings offer six (6) clamping bolts per ring plus strong, dual steel base-clamps that self-center on Weaver or Picatinny rails. These aluminum XTR Signature Rings provide strength and holding power, plus the key benefits of Pos-Align inserts. As impressive as XTR rings are — they aren’t that expensive, with 1″-diameter XTRs starting at about $87.00 per pair (30mm and 34mm XTRs cost a bit more).

The polymer inserts in Signature rings perform three key functions. First, the inserts provide full, uniform scope-to-ring contact, with no need for lapping. You get a very secure “grip” on your scope without ring marks. Second, the Pos-Align inserts can provide elevation “pre-load”. With eccentric (offset) inserts, you can raise the back of the scope relative to the front, gaining up to 54 MOA of built-in elevation, without the need for expensive tapered bases. Third, the offset inserts can be rotated clockwise or counter-clockwise to shift point of impact. This lets you zero your rifle easily while keeping the turrets in the center of their travel.

Burris XTR Signature Rings are offered in 1″, 30mm, and 34mm diameters, and three (3) different heights: 1″, 1.25″, and 1.5″. Each ring set includes two sets of concentric inserts and one set each of the following offset inserts: +/-5 MOA, +/-10 MOA, +/-20 MOA. These allow you to “pre-load” elevation and/or center up your cross-hairs.

– Pre-load Elevation. No need for expensive tapered bases for long-range shooting.
– Correct misalignment caused by off-center receiver holes.
– Correct for bases or rings being slightly off-center.

How to Pre-load Elevation
To add elevation, set the Pos-Align Offset Inserts to raise the rear of the scope and lower the front. As long as there remains sufficient clearance between the front objective bell and the barrel, Burris recommends lowering the front of the scope the most and raising the rear of the scope the least. The amount of actual elevation “pre-load” will depend on the ring spacing (see chart). In the illustration, with 4.75 inches between ring centers, a +/- 20 MOA pair in the front combined with a -/+ 5 MOA pair in the rear will yield +25 MOA of total elevation. (If the rings are positioned further apart, you’ll get less elevation pre-load.)

Using Inserts to Adjust Point of Impact in Any Direction
Although it is convenient and most understandable to refer to the ring inserts as a “bottom” or “top” insert, the inserts may be rotated to any angle within the scope rings. This allows the shooter to correct the point-of-impact in any direction. The drawings below show how the inserts can be rotated to induce both elevation and windage changes at the same time.

Product tip from Boyd Allen. We welcome reader submissions.

The First Shot, the CMP’s archived Online magazine, has an article by Spc. Tyrel Cooper of the U.S. Army Marksmanship Unit (USAMU). In his article, Straight to the Rear, Spc. Cooper describes proper trigger hand and finger positions and how to best “break the shot”. This well-written article will help anyone who shoots off-hand, or who uses an AR or Spacegun-type rifle with a vertical pistol grip.

Cooper explains: “Trigger control is one of the two main principles of shooting that we teach. You can have the best position in the world with perfect sight alignment, but if you have bad trigger control, you have wasted all that effort that you put into your position and sight alignment.”

Photo Credit: CMP image from 2019 CMP 1000 Aggregate at Camp Perry.

Firing Hand Position and Finger Placement
“Good trigger control begins with a good firing hand position. Place your firing hand high on the pistol grip, with a good firm grip. Grip tension should be like giving someone a hand shake or holding a child’s hand while walking across a street. A good firm grip [helps you] move your trigger finger without moving your other fingers. Try this, hold out your firing hand with fingers extended; now try moving your trigger finger to the rear as if you were pulling the trigger. Unless you concentrate very hard on moving just your trigger finger, other fingers will move. Now make a fist as if you were grabbing a pistol grip, now you can move your trigger finger freely without introducing movement in the other fingers.”

“I’m sure you have heard advice to place the tip or the pad of your finger on the trigger. This is true if you have short stubby fingers and that’s where the index finger naturally rests, but if you have long fingers like myself you want more of your finger around the trigger…. By placing your finger where it naturally rests on the trigger you are ensuring that you are pulling the trigger straight to the rear, and this also allows you to get more leverage on the trigger.”

Rapid-Fire Trigger Technique
“Trigger control for the rapid-fire stage is different than it is for standing. You can actually take a little bit more time to break your shots in rapid fire because of the steadiness of a supported position. A good rapid fire shot process is: 1) drop down into position, 2) get your natural point of aim, 3) take up the first stage on your first shot, 4) break that shot smoothly and hold the trigger all the way to the rear through recoil, 4) once recoil has ceased, let the trigger out only far enough to reset the trigger (you should hear a metallic click of the trigger resetting) and continue by firing your second and succeeding shots.

By doing this, you already have most of the weight of the trigger taken up so the next shot is ready to go without having to take up all the weight of the trigger every single shot.”

Slow-Fire Prone Technique
“During the slow fire prone stage, you have even more time to break your shots, so you would use the slow–smooth method. You should have little or no hold movement at all, thus allowing you to acquire good sight alignment, a good sight picture and break the shot using slow and smooth trigger control. Again you want to hold that trigger all the way to the rear until recoil has ceased so you do not disturb the rifle, no matter what position you are shooting.”

Standing Trigger Technique
“When you are shooting standing have you noticed that the rifle never really stops moving? Well, this is where you would want fast and smooth trigger control. When I come down and start settling on the target, I take up the first stage of the trigger. Once I’m getting to the end of my firing process and the movement has slowed down, I manipulate the trigger fast, but smooth, to the rear when I see what I want to see in my sight picture. Over time, this will become a subconscious act; when your brain sees the sight picture, it will automatically tell your trigger finger to move instead of you having to tell yourself there it is, take it. Lots and lots of dry firing will help this process. To repeat, you want to be fast and smooth!”

CLICK to READ FULL ARTICLE »

For years we have touted the advantages of Burris Signature rings, with polymer Pos-Align Inserts. PRS/NRL shooters take note — this technology is available in a beefier, heavy-duty ring system for tactical rifles. The impressive Burris XTR Signature Rings offer six (6) clamping bolts per ring plus strong, dual steel base-clamps that self-center on Weaver or Picatinny rails. These aluminum XTR Signature Rings provide strength and holding power, plus the key benefits of Pos-Align inserts. As impressive as XTR rings are — they aren’t that expensive, with 1″-diameter XTRs starting at about $90.00 per pair (30mm and 34mm XTRs cost a bit more).

The polymer inserts in Signature rings perform three key functions. First, the inserts provide full, uniform scope-to-ring contact, with no need for lapping. You get a very secure “grip” on your scope without ring marks. Second, the Pos-Align inserts can provide elevation “pre-load”. With eccentric (offset) inserts, you can raise the back of the scope relative to the front, gaining up to 54 MOA of built-in elevation, without the need for expensive tapered bases. Third, the offset inserts can be rotated clockwise or counter-clockwise to shift point of impact. This lets you zero your rifle easily while keeping the turrets in the center of their travel.

Burris XTR Signature Rings are offered in 1″, 30mm, and 34mm diameters, and three (3) different heights: 1″, 1.25″, and 1.5″. Each ring set includes two sets of concentric inserts and one set each of the following offset inserts: +/-5 MOA, +/-10 MOA, +/-20 MOA. These allow you to “pre-load” elevation and/or center up your cross-hairs.

– Pre-load Elevation. No need for expensive tapered bases for long-range shooting.
– Correct misalignment caused by off-center receiver holes.
– Correct for bases or rings being slightly off-center.

How to Pre-load Elevation
To add elevation, set the Pos-Align Offset Inserts to raise the rear of the scope and lower the front. As long as there remains sufficient clearance between the front objective bell and the barrel, Burris recommends lowering the front of the scope the most and raising the rear of the scope the least. The amount of actual elevation “pre-load” will depend on the ring spacing (see chart). In the illustration, with 4.75 inches between ring centers, a +/- 20 MOA pair in the front combined with a -/+ 5 MOA pair in the rear will yield +25 MOA of total elevation. (If the rings are positioned further apart, you’ll get less elevation pre-load.)

Using Inserts to Adjust Point of Impact in Any Direction
Although it is convenient and most understandable to refer to the ring inserts as a “bottom” or “top” insert, the inserts may be rotated to any angle within the scope rings. This allows the shooter to correct the point-of-impact in any direction. The drawings below show how the inserts can be rotated to induce both elevation and windage changes at the same time.

Product tip from Boyd Allen. We welcome reader submissions.

The Sniper’s Hide Cup competition went forward this year, despite challenges presented by the COVID-19 pandemic. The event took place June 20-21, 2020 in Colville, WA. This was a backcountry match, set in beautiful green mountain scenery. Here are images from the 2020 SH Cup as posted on the Sniper’s Hide Facebook Page. Congrats to Frank Galli (aka “Lowlight”), founder of Sniper’s Hide, and all the participants in the event. Looks like a great two days of shooting.

The Everyday Sniper Episode 260: Sniper’s Hide Cup 2020

After the 2020 SH Cup event, Frank Galli hosted an informative podcast:

Topics include: Stages, Targets, Equipment, Mindset, First-Time Competitors
Frank: “I’m back from the Sniper’s Hide Cup in Colville, Washington. I’ll be breaking down some lessons learned and give you my observations from the field and competitors with whom I spoke. [We cover] the experience of attending a match and helping new shooters — the juniors, the first time competitors, and how you work with them. Thanks for listening, sharing, and commenting on the Everyday Sniper Podcast.”

For years we have touted the advantages of Burris Signature rings, with polymer Pos-Align Inserts. PRS/NRL shooters take not — this technology is available in a beefier, heavy-duty ring system for tactical rifles. The impressive Burris XTR Signature Rings offer six (6) clamping bolts per ring plus strong, dual steel base-clamps that self-center on Weaver or Picatinny rails. These aluminum XTR Signature Rings provide strength and holding power, plus the key benefits of Pos-Align inserts. As impressive as XTR rings are — they aren’t that expensive, with 1″-diameter XTRs starting at about $90.00 per pair (30mm and 34mm XTRs cost a bit more).

The polymer inserts in Signature rings perform three key functions. First, the inserts provide full, uniform scope-to-ring contact, with no need for lapping. You get a very secure “grip” on your scope without ring marks. Second, the Pos-Align inserts can provide elevation “pre-load”. With eccentric (offset) inserts, you can raise the back of the scope relative to the front, gaining up to 54 MOA of built-in elevation, without the need for expensive tapered bases. Third, the offset inserts can be rotated clockwise or counter-clockwise to shift point of impact. This lets you zero your rifle easily while keeping the turrets in the center of their travel.

Burris XTR Signature Rings are offered in 1″, 30mm, and 34mm diameters, and three (3) different heights: 1″, 1.25″, and 1.5″. Each ring set includes two sets of concentric inserts and one set each of the following offset inserts: +/-5 MOA, +/-10 MOA, +/-20 MOA. These allow you to “pre-load” elevation and/or center up your cross-hairs.

– Pre-load Elevation. No need for expensive tapered bases for long-range shooting.
– Correct misalignment caused by off-center receiver holes.
– Correct for bases or rings being slightly off-center.

How to Pre-load Elevation
To add elevation, set the Pos-Align Offset Inserts to raise the rear of the scope and lower the front. As long as there remains sufficient clearance between the front objective bell and the barrel, Burris recommends lowering the front of the scope the most and raising the rear of the scope the least. The amount of actual elevation “pre-load” will depend on the ring spacing (see chart). In the illustration, with 4.75 inches between ring centers, a +/- 20 MOA pair in the front combined with a -/+ 5 MOA pair in the rear will yield +25 MOA of total elevation. (If the rings are positioned further apart, you’ll get less elevation pre-load.)

Using Inserts to Adjust Point of Impact in Any Direction
Although it is convenient and most understandable to refer to the ring inserts as a “bottom” or “top” insert, the inserts may be rotated to any angle within the scope rings. This allows the shooter to correct the point-of-impact in any direction. The drawings below show how the inserts can be rotated to induce both elevation and windage changes at the same time.

Product tip from Boyd Allen. We welcome reader submissions.

There’s a formidable new option for PRS Production Class. MasterPiece Arms (MPA) is bringing out a new tactical/practicalcompetition rig, officially called the MPA BA PMR Competition Rifle. This new rifle has a $1999.99 price tag, making it suitable for Production Class. It will be offered with Curtis Action fitted to an X-Caliber, hand-lapped 26″ match barrel. Three chamberings will be available: 6mm Creedmoor, 6.5 Creedmoor and .308 Winchester.

This rifle is designed specifically for the Production Class requirements of the Precision Rifle Series (PRS) and has been approved for use within this division. It includes many competition-related features while staying under the $2,000 price limit for this class. It is available in either a Black or Tungsten Cerakote® finish. Accuracy is helped with a very good barrel — an X-Caliber, hand-lapped 416R Stainless premium barrel with a polished finish. The chamber is indicated within 0.0001” or less to the bore of the rifle.

The MPA BA PMR Competition Rifle utilizes the MPA BA Ultra Lite Chassis, CNC-machined from 6061 aluminum. The V-bedding system provides additional clearance for glass bedding action and straight section of the barrel. The chassis also includes a built-in inclinometer, thumb notch, lower mounted Picatinny Rail, 20 MOA Scope Rail, A2 Style Pistol Grip and is R.A.T. System compatible. The MPA Buttstock comes with an adjustable cheek riser and length of pull that are locked in position with a series of set screws that are embedded into the buttstock body. This is the same system MPA uses on its Standard BA Chassis, but without the thumb wheels.

The Ruger Precision Rifle goes big — major Magnum-size big. Back in October we revealed that Ruger was releasing new .338 Lapua Magnum and .300 WinMag versions of the Ruger Precision Rifle (RPR). These Magnum RPRs feature longer, stronger actions, and some key upgrades, such as a +30 MOA rail and beefy muzzle brakes on the end of the 26″ 5R Barrels. These are pretty impressive rigs for the money — $2099 MSRP, with the “street price” well under $1700.00.

READ .338 Lapua Magnum RPR GunsAmerica Test »

So how do these Big Rigs shoot? GunsAmerica.com recently answered that question, testing a .338 Lapua Magnum RPR with a variety of factory ammo types. GunsAmerica’s tester Clay Martin, a skilled former military sniper (retired from 3rd Special Forces group), shot the rifle from prone off bipod. With Hornady 285gr Match Ammo, Martin drilled two 3-round groups that both measured right around a half-inch. With some other ammo, results were ugly, but the 285-grainers showed that the gun could shoot. (Five-shot 100-yard groups with Federal 300gr ammo were around 1.3 MOA — see photo below).

Overall Martin came away impressed: “My respect for the RPR in .338 Lapua Magnum is high. If it will shoot ½ MOA at 100, there is no reason to think it won’t at any range a match bullet will fly [provided you call the wind right]. Despite the uber-manly caliber, the gun was fun to shoot. The muzzle brake and weight do a great job of taming recoil[.] For a .338 Lapua-caliber rifle, I can’t think of a single better option below $5,000. If you have been waiting to step into the big boy rounds, this is a golden opportunity.”

Watch Field Test of .338 Lapua Magnum Ruger Precision Rifle:

RPR Magnums Boast 5R Barrels with Big Brakes
The new RPR magnums feature hammer-forged, chrome-moly heavy-contour 5R barrels fitted with tunable muzzle brakes. Those fat, large-port brakes will certainly reduce recoil and muzzle jump but we wouldn’t like to be shooting beside the .338 LM RPR — expect lots of side-blast. The new RPR magnums feature 18″ free-float anodized handguards with M-LOK accessory attachment slots on all four sides. Integral QD sling attachment points eliminate the need for additional adaptors and a flat-bottom 1.50″ dovetail is compatible with RRS S.O.A.R. and similar QD systems.

The .338 Lapua Magnum RPR features a 1:9.375″ twist rate while the .300 Winchester Magnum model features a 1:9″ twist rate, both of which stabilize long-for-caliber projectiles. These rifles ship with two, 5-round AI-style magazines. As with all RPRs, the bolt is a 3-lug design with 70-degree bolt lift.

Angled +30 MOA Rail and Adjustable Stock Standard
ELR shooters will be pleased that the new, magnum-caliber RPRs ship with a +30 MOA Picatinny rail. That will help give shooters enough elevation to shoot out to 1500 yards and beyond. As with other Ruger Precision Rifle models, the magnums feature a folding stock with adjustable comb height and length of pull. The Ruger Marksman trigger is user-adjustable between 2.25 and 5 pounds.

Many of our readers are thinking of trying out PRS-type competition. Tactical matches are becoming more popular every season. Along with F-Class, tactical/practical disciplines are the fastest-growing forms of competitive rifle shooting. Rich Emmons, one of the founders of the Precision Rifle Series (PRS), has written an insightful article about getting started in the tactical game. This will help PRS novices pick the right equipment and understand the game. Here are highlights from Emmon’s “PRS — Intro to Competition” article, originally published on the PRS website. You may also want to read the current PRS FAQ Page.

Precision Rifle Series — Intro to Competition

by Rich Emmons, PRS President
Tactical Shooting with a precision rifle is not like other disciplines, there is no set course of fire or format. That is what makes it so fun!

Photo from Ramia Whitecotton’s GAP GRIND 2016 photo album.

First, you have to ask yourself what do you want to accomplish. When I was introduced to long range shooting, immediately a light turned on for me, once I saw how easy it was to hit 300–600 yard targets. What I quickly learned from my first competition and the many that followed was there is so much to learn and shooting in competition put everything you thought you knew to the test. So back to the question: “What do YOU want to accomplish?”. The reality is you may not know yet, you just think it is cool to have a bad ass rifle and scope that can make almost any shot. Now if you’ve got that rifle and scope, it’s time to take it to the next level.

Watch PRS 2016 Championship

Getting Started — What to Expect
If you’re reading this, you have probably already have been bitten by the long range shooting bug. It can seem quite intimidating to just jump in with a new bunch of shooters you don’t know and shooting lingo you don’t quite understand yet. But here is the key — show up and shoot! I guarantee you if you show up to a match as a new shooter, other experienced shooters will guide you along and give you help on anything you need.

Now, a couple things you should just expect. You’re not as good as you think you are. Don’t expect to come into your first match and beat all the veterans. That just doesn’t happen unless you have had some really good coaching or other shooting competition experience to get you ready for this type of competition. If possible, find a local rifle club that has monthly long range matches, or any type of match will help prepare you for a larger PRS event. Getting involved with a rifle club and starting out shooting monthly matches is definitely the way to jump into competition shooting.

The Gear You Need
The first question that many ask is: “What kind of rifle/caliber/scope do I need?” The easiest answer to this is, the best you can afford. It’s no secret the gear is expensive. It took me several years of buying sub-par gear and eventually trading up to figure this out. Now, a guy can get a real sense of pride of doing it on the cheap, or with a factory rifle. I’ve seen many old Savage 10FPs take down custom rigs that cost 10 times as much. And if that’s all you can afford, then eventually you will learn the limitations of yourself or your gear. As for choice of cartridge/caliber, the respected Precision Rifle Blog has analyzed four years worth of match results from the best tactical shooters in the nation. CLICK HERE to read a PRB article that reveals what the “top guns” use.

Craig Arnzen of Area 419 has created a useful article reviewing the gear PRS shooters need, including support bags, hearing protection, and other key accessories such as muzzle brakes. This helpful article also covers factory ammunition options.

Making Good Ammo
Producing quality reloads is something you have to master. It’s not hard at all, you just have to pay attention to detail, and eventually you are going to do something stupid like mis-priming your brass, or skip a row of brass when dumping your powder. Everybody has their own horror story of some reloading failure that cost them a stage or even a match. So load to perfection, work with your rifle to find what load it likes the best, then start your practice.

Practice Makes Perfect
You want to become ONE with your rifle, learning everything you can about its functionality. Getting comfortable with the operation of your rifle is key. Learn the feel of your trigger, dry-firing until you wear the paint off your bolt handle. Learn how the rifle works best — pay attention to little things like the sound and feel of the bolt feeding a round from the mag (or when it doesn’t). Learn how to remove a jammed round quickly, learn how to reload a magazine quickly. Learn to scan across a field and find targets in a quick manner, seeing the targets with your eye and coming into the scope on target. These are some of the basic practices that separate the new shooters from the seasoned ones.

Many of our readers are thinking of purchasing a Howa rifle or barreled action. These feature smooth-running actions with a good two-stage HACT trigger. But some folks have heard that it may be difficult to find stocks, or to fit an after-market barrel. That’s not true. There are many stock options available, and in this article, Bill of RifleShooter.com shows that it is easy to remove the factory-installed barrel with the right tools. We think a Howa makes a fine basis for a varmint rig or field rifle. Or you can build a tactical as Bill did. You can start with the factory barrel and when you want/need more accuracy, then have a gunsmith install a custom barrel from Krieger, Shilen, or other quality brand.

What You Need to Know About Howa 1500-series Rifles

Tech Feature by RifleShooter.com
Consider this article the “Howa 1500 Overview”. AccurateShooter.com’s editor mentioned there’s been a lot of interest in Howa rifles and barreled actions imported by Legacy Sports International. In addition to being able to buy a complete rifle from a dealer, Brownells sells barreled actions in a wide variety of calibers and configurations. In this post we are going to take a look at the Howa 1500 series.

Howa Rifles — General Background
Howa is a Japanese heavy machinery company. One of its product lines are firearms, which, are imported into the United States of America by two different companies, Legacy Sports International and Weatherby. Legacy sells the 1500 under the manufacturers name while Weatherby re-brands the guns as the Weatherby Vanguard. In general, the finishes on the Weatherby rifles are more refined than the LSI-imported 1500s.

General Evaluation of Howa 1500 Rifles
I’ve found Howa 1500s to be solid, entry-level rifles that are capable of sub-MOA accuracy out of the box. I’ve actually purchased two Howa rifles I’ve tested because I like them so much. The gun below, a Howa Mini-Action in 7.62×39 Russian, is one of my favorite factory guns to shoot. I’m running a Tract Optics Toric on it, these are solid little rifle scopes that offer great performance for the money.

Check out this three-shot group I drilled at 100 yards with the rifle above and 125-grain Sierras. It took a lot of work and load development to get there, but when it did, it worked well.

Howa 1500 HACT 2-Stage Trigger
Howa 1500s feature the very nice Howa HACT trigger. This is an adjustable, two-stage trigger, set for about 3 pounds (combined stages). Crisp and repeatable, this is an excellent trigger for a factory gun. There is no annoying Glock-style safety lever in the middle of the trigger blade. The 2-stage design and pull weight range works well for a hunting rifle or a rig for PRS competition. Rifleshooter.com says the Howa trigger is “one of the best factory triggers, along with Tikka. I’ve found the Howa trigger superior to a Remington 700 — the Howas doesn’t need to be replaced.

Writing for the Western Outdoor News, WONews.com, Steve Comus has field-tested the new HACT Trigger. Steve writes: “I always liked two-stage triggers, because of the way I could take-up the slack and then actually know when the rifle was going to go off. The take-up on the [HACT] trigger was fast and easy. The crisp, positive release when pressure was put on during the second stage [reminded me] of some of the target rifles I shot through the years.”

Howa Actions — Three Options
Howa offers three action lengths: Mini, Short, and Long. You can see the bolts for the three action lengths in the image below. The Mini-Action has similar external dimensions to the Remington Model Seven, however, the Mini-Action’s bolt does not travel as far to the rear. This is a mixed bag. The upside is you have a quicker action (shorter bolt throw). The downside is you are limited to shorter rounds such as the .223 Remington, 7.62×39mm Russian, and 6.5 Grendel. But if you need a bigger cartridge, just choose the standard or long action Howa variant.

Howa 1500 vs. Remington 700 — Important Differences
Is the Howa 1500 a Remington 700 clone, or some kind of improved Remington 700? No, not really. While the top radius of the Howa 1500 does match the Model 700, and they can both use the same two-piece scope bases, there area number of differences.

If you look at the Howa 1500 alongside the Remington 700 you’ll note the M700 is a round action, while the Howa is a flat-bottom action. In many ways the Howa’s bottom half reminds me of a push-feed Winchester. This means the chassis and stocks that support a Howa 1500 are not V-block based like you’ll find on a 700, instead they have a flat bottom. While the bolt of the Howa is similar in external appearance to the Model 700, it does offer some improvements, notably an M16-style extractor and a firing pin assembly that can be easily removed without tools.

Howa 1500 action screws are metric and are in a different location from the 700. The Howa 1500 has an integral recoil lug that accepts the front action screw, this means you have more of the front action screw engaging the action. WARNING: If you install it into a poorly-fitted stock or action you may bind it.

Can a Howa Action Be Used for a Custom Rifle Project?
Absolutely! You can either buy a barreled action from Brownells and throw it in a chassis system/stock of your choice or you can use a stripped action to build a custom rifle. If you are in the chassis market, MDT offers a wide variety of chassis in different price ranges. All have worked well for me.

How to Remove Howa Factory Barrel from Action
You may have heard internet grumblings about removing Howa barrels. Some keyboard commandos say they are extremely difficult to remove without a relief cut. Well Bill at Rifleshooter.com demonstrates that Howa barrels can be removed without trouble, provided you have the right tools. Watch this video:

Watch Howa Barrel Removal Video — Quick and Easy (Click Speaker Icon for Audio)

Q: Is it difficult to remove a barrel from a Howa 1500?
A: Not very. I’ve heard from some smiths that worked on Howas (years ago) that the factory barrels are difficult to remove. However of the half dozen or so Howa barrels that I’ve pulled, they’ve been very easy. I use a Brownells action wrench with the top piece for a Rem Model 700 and the flat bottom resting against the flat on the wrench.

Howa Actions Require Metric Barrel Threads
It’s easy to thread a barrel for a Howa Action. You just have to cut metric threads — most lathes out there can cut them. I cut the threads below on a manual lathe using change gears. [Editor: John Whidden cuts metric tenon threads with a CNC lathe. “It’s easy,” John tells us, “No issue whatsoever.”]

Using Howa Actions for Custom Rifles
I have built a few customs with Howa actions. Below is one of my favorite, a .308 Winchester. It consists of a Howa 1500 action, Shilen Select Match Remington Varmint contour barrel, and Modular Driven Technologies (MDT) ESS chassis. Great rifle and it hammers!

To learn more about Howa rifles and actions, visit Legacy Sports International. To buy a Howa barreled action, visit Brownells.com.

To learn more about modular chassis systems for Howa rifles, visit MDTTAC.com

We like Howa 1500-series rifles. The major attractions are the smooth-running action (feels almost like a custom), a very good two-stage trigger (way better than most domestic factory triggers), pretty decent barrels, and excellent fit and finish. Howa also offers a “mini” action that’s nearly an inch shorter than a conventional short action. The only negative is that the Howa actions have metric barrel threads. That complicates the re-barreling task for some gunsmiths who don’t have the right equipment. All-in-all the Howa 1500 series is still a fine value, offering excellent “bang for the buck”. If we were choosing a new varmint or hunting rifle, the Howa would be one of our first choices.

Given our positive outlook towards Howa rifles, we were pleased to see that American Rifleman just named the Howa 1500 HCR rifle (with scope package) as the NRA Gun of the Week. Check it out:

Designed for PRS “factory class” competition and tactical applications, the Howa HCR offers the smooth-running 1500 action with HACT 2-Stage trigger in a fully-adjustable aluminum chassis. The Howa’s MSRP is $1299.00, with “street price” around $990.00 in black or $1180 with Camo finish so the HCR is directly competitive with the Ruger Precision Rifle (RPR). Available chamberings are: .223 Remington, .243 Winchester, 6.5 Creedmoor, and .308 Winchester.

Mounted on an AR-style buffer tube system, the Howa HCR utilizes the fully adjustable LUTH-AR MBA-3 stock. Length of Pull is adjustable from 12.5″ to 16.75″. Comb height is also adjustable to fine tune for scope height-over-bore. Weight with a 24″ barrel is 10.2 pounds (before optics), so this Howa HCR is lighter than many similar rifles on the market.