A while back, our friend Dennis Santiago was conducting training for a Southern California Police Department. During a training session one of the unit’s AR15s stopped functioning. The problem — the bolt in the AR rifle broke in half. Dennis states: “They ran the gun dry, broke for lunch, shot it again. They don’t like that. I personally like to flood the bolt wet with lube on training days. It prevents stuff like this. Given that, it’s a simple remove-and-replace fix.”
Here are some of the more interesting comments about this parts failure — an AR bolt that literally sheared in half:
“If I was a betting man [the steel] wasn’t made by Carpenter Steel. They are one of the few companies that use the correct [milspec-steel, C-158] called out on the drawing which they coincidentally developed. Most of the other companies that make [AR Bolts] use different steel with the same heat treat specification as what is called out which gives them the potential of being a little on the brittle side at the upper end of the tolerance. When it comes to the AR platform, bolts are probably the only part of the entire gun where I must admit to being a little bit of a brand snob.” David O’N.
[Editor’s Note: Actually Carpenter Steel does not make AR bolts. They are a steel supplier, and yes Carpenter did develop the original C-158 steel for AR bolts. Here is a contrary view, claiming that AISI 9310 Steel is actually stronger than milspec Carpenter C-158: 9310 Steel for AR Bolts.]
“Dry bolt and carrier shouldn’t cause that. Looks like a big pressure spike. What kind of ammo…?” Guy G.
Reply from Dennis: “55gr factory ammo. Piles of it.”
“Is that the new two-piece bolt everyone’s been talking about LOL?” — Darren R.
“Let me guess…the PD called you in cause they didn’t know why it stopped going ‘pew pew’?” — Jim O.
Reply from Dennis: “I was there today for qualifications. It broke during the rifle phase. Simple enough to fish the bolt parts out of the action. The training didn’t miss a beat. I have an armory full of the things.”
Spring is coming soon, and that means it’s time to get ready for early varmint season. Here are eight great rifles from our Shooters’ Forum Favorite Varmint Rifles Thread. You’ll see a variety of action types and stock designs, both custom and factory. And we’ve featured a wide range of chamberings, from 17 Fireball up to a .243 Super Rock Chucker (aka 6mm-06). The common factor is serious accuracy. All these rigs are great shooters that have brought smiles to their owners while bringing doom to varmints.
1. Rem 700 in 20-222 — with Birthday Gift Barrel from Dad
This is proof that you don’t have to spend a fortune to have a great varmint rig. Forum member JDS Holler posted: “Here’s my baby, ‘Plain Jane’. I took a $500 birthday check that my Dad gave me, and ordered a great barrel from PacNor, chambered in 20-222. I got busted up in a fall, and had four months down time to accumulate the components to add to my old .222 Rem 700 donor action. I couldn’t be happier with the outcome. That old Bushnell has been replaced by a Vortex Viper, and this rifle just flat shoots.”
2. 6 BRA with Krieger Barrel from Alex Wheeler
Alex Wheeler of Wheeler Accuracy knows a thing or two about accurate rifles, having built many match-winning benchrest rifles. For varmint work he likes the 6 BRA (BR Ackley) wildcat cartridge: “My favorite varmint setup is this 6mm rifle with BAT SV action in a Nesika bay varmint stock with a 1:8″-twist Krieger HV contour barrel chambered for 6 BRA. I like the 6mmBR and variants (Dasher, BRX, 6BRA) with zero freebores.” He gets great results with 55-60 grain Sierras and Noslers with H322 powder: “I shot 55 Sierra Blitzking, 55 Nosler Ballistic Tip, and 60gr Sierra Varminter HP. H322 was the best powder. Jam ‘em 10 thou in the rifling — and of them — and man they were like magic.” Alex also feels the 6mm rifles are easier to tune than 22-caliber varmint rigs and the 6mm barrel throats last longer. He often puts an older 6mm match barrel on a varmint gun and it still holds quarter-MOA.
Alex recommends sticking with a 1:8″-twist even when shooting light 6mm bullets. The extra RPM makes the bullets MUCH more explosive on critters: “I’ve done one 1:13.5″-twist and I’ll never do that again. I’m not kidding, with the 8-twist it’s twice as energetic. It can lift those ground squirrels 20 feet in the air. With the 13.5-twist it’s not half that.”
About the Suppressor — The rifle is wearing a “can” in the photo. However, Alex tells us that he now avoids suppressors for most varmint work: “I didn’t like the suppressor — it put off so much heat that the mirage was terrible. With the heat mirage, after 5-10 shots you couldn’t see. I learned my lesson. I pulled that sucker off after the first time I shot it.”
3. 6mm Dasher in Convertible Laminated Stock
The 6mm Dasher has won many benchest matches, and it’s also an ultra-accurate varminting cartridge. This Dasher belong to Forum member MTLager who posted: “Here’s my baby — 6 Dasher with BAT SV action. First one built. Serial number PT1.” This impressive rig features a tack-driving, 1:8″-twist Brux Heavy Varmint contour barrel. This rig is “Smokin the 75gr V-Maxs” reports MTLager. The stock is very interesting. MTLager explains: “This is a Richard Franklin laminated blank made into a stock by J.T. Barber. It has a 3″-wide fore-end for varmint shooting. But I can change the front to 4″-width and a rear section can be removed.” The angled rear “toe” of the buttstock can be taken off, allowing a flat, straight bottom for benchrest competition.
4. Slick 17 Fireball with BAT Action and Stunning Stock
This rifle is almost too pretty to carry out into the varmint fields. Look at that wood! This handsome small-caliber varminter belongs to Forum member “20 TAC”. Chambered for the 17 Fireball wildcat (.221 Fireball necked down), this rig features a BAT Action, Jewell Trigger, and a custom exhibition-grade walnut stock sporting a true ebony fore-end cap. The checkering is exceptional. Owner 20 Tac report this rig “shoots 20 grain V-Max bullets with H4198 very well.” That’s a Nightforce scope on top.
5. 6mmBR in McMillan Stock with Krieger Barrel
This website stated 17 years ago as 6mmBR.com, so we had to include a classic 6mmBR Norma in today’s varmint rifle line-up. Forum member Powderbrake posted: “Here is my favorite varmint rifle — [a 6BR with] Stiller Predator V RBLP action, bedded in a McMillan stock.” This accurate varminter features a 1:8″-twist 6mm Krieger barrel and Jewell trigger. Up top is a Nightforce NXS 8-32x56mm scope. Below are the owner’s key gear items: Leica Laser-Rangefinding Binoculars, Smartphone with Applied Ballistics software, and Kestrel Weather Meter. Powderbrake told us he recently upgraded to a Model 5700 Kestrel with ballistics software and LiNK. (Editor: The $399.00 Kestrel 5700 has ballistics software, but if you want the full Applied Ballistics suite, order the $699.00 Kestrel 5700 Elite).
6. Efficient 20 Vartarg for Prairie Dog Adventures
The .20 Vartarg is based on the .221 Fireball case, necked down to .204 and slightly modified for extra capacity. This very efficient cartridge offers low recoil and great accuracy. It’s one of our first choices for ground squirrels and P-dogs out to 300 yards. 20 Vartarg here belongs to Forum Member DogBuster, an avid varminter based in Utah. He posted: “If I recall, I had a hot spot in this location — probably kilt 150+ prairie dogs that morning. The hay wagon helped too, offering added elevation.”
7. Long-barrel SAKO Action Varminter in .243 Super Rock Chucker
Here is another .243 wildcat, chambered for the .243 “Super Rock Chucker”. This long-barreled rig belongs to Forum member MikeGaiz. The rifle features a SAKO action fitted with a 30″ Kreiger barrel chambered for the .243 Super Rock Chucker. From what we have read, the .243 Super Rock Chucker is a .25-06 cartridge necked down to .243 (6mm). Yes this is a barrel burner, but it can definitely “reach out and touch” varmints at VERY long range. Owner Mike reports hits at 1275 yards on prairie dogs in South Dakota. This cartridge drives Sierra 6mm 85gr HPBTs at 3440 FPS. That’s serious speed for an 85-grainer.
8. AR-10 Custom in .243 Winchester
Forum Member Urban Rifleman calls this .243 AR10-platform rifle the “Goblin Killer”. This Gen 2 DPMS rifle features a Craddock Precision Bartlein 1:8″-twist 5R barrel chambered in .243 Winchester with a Tubb assymmetrical muzzle brake. Up front is the unique Tubb Bipod which reduces hop. The buttstock is a Magpul PRS Gen 2. The scope is a Leupold VX-3i LRP 6.5-20x50mm FFP TMR. We’re told this rig “will easily shoot 1/2 MOA, sometimes much smaller”.
Urban Rifleman produces a variety of great gun accessories sold through TheUrbanRiflemanStore.com. That green grip is his Urban Rifleman/Tubb ergonomic grip.
Parting Shot from Groundhog Country, SW Pennsylvania
This nice tripod with rifle mount (and Rem 40XB 22-250 on top) belongs to Forum Member Snert.
Applied Ballistics Founder Bryan Litz and Former USAMU and Team USA coach Emil Praslick III share their wisdom in an informative Guns Magazine Podcast. Along with being a true ballistics guru, Bryan Litz is an outstanding competitive shooter, having won F-TR National Championships, and both Sling and F-TR divisions at the Berger SW Nationals, along with many other matches. Emil is considered one of the world’s great wind-readers and team coaches, having coached 20+ championship teams.
Guns Magazine podcast host Brent Wheat asks Bryan and Emil about multiple topics including: exterior ballistics, bullet design, wind reading, ballistic solvers, BC myths, and more.
Brent reports: “Together, Bryan and Emil understand what happens from the time a bullet leaves the muzzle until it impacts the target, including the atmospheric affects along the way. Grab a pencil, listen in, and get ready to take notes.”
This Long Range Grad School podcast features Berger’s Chief Ballistician, Bryan Litz, and Berger’s Emil Praslick. Both have extensive long range competitive shooting experience, with championship titles (as shooter and/or coach) in a multitude of long range disciplines. CLICK arrow below to start podcast audio:
Emil Praslick (left) confers with Bryan Litz (right) at King of 2 Miles ELR Event.
In this Video Emil Praslick explains his methods for determining wind direction.
Bryan Litz coaching Team USA in Canada using a WIND PLOT.
Bryan Litz at 2011 World Long Range (Palma) Championships in Brisbane, Australia
Yes we miss the good old days… when reloading components were readily available and very affordable. Today, on Gunbroker, a single 1000-count box of primers may sell for well over $300. And some vendors are asking $90 for a single pound of powder that sold for $30 per pound just last year.
We can’t change prices for you, but we can offer a “sentimental journey” back to the “good old days” via a Flashback Thread in our Shooters’ Forum. There, Forum members have posted some items from their collections, with the original prices.
What is the best deal you can remember? How about $1 per pound forty-six years ago — member STS posted: “It was probably 1975 when I bought 100 pounds of H335 from Bruce Hodgdon for $100. It came in cardboard boxes with black trash bags inside. I shot every flake of it at prairie dogs.”
Reloder Powder from Hercules (Now Alliant) for $3.80 per Pound
CCI and Winchester Primers, $16.30 and $13.00 per Thousand
Today some CCI primers are selling for over $300 per thousand on Gunbroker. Member JayHHI6818 said: “Found these the other day in a shoe box in our bedroom closet!”. Nice find Jay!
Hodgdon H4350 for $10.87 per Pound
H4350 remains one of the most popular powders with competitive shooters. It’s ideal for many midsized cartridges, offering great accuracy and temp stability. Today it’s hard to find this powder at ANY price!
Remington 2 1/2 Primers for $1.50 per Hundred
Remington Arms folded. However Remington primers will be produced by Vista Outdoor after the collapse and bankruptcy of Remington Arms. Vista Outdoor, which owns CCI and Federal, will take over the Remington ammunition production facilities.
New American President Joseph Biden, just three weeks after taking office, called for radical, sweeping gun control measures that could dramatically harm the gun industry and strip away citizens’ rights under the Second Amendment of the U.S. Constitution.
On February 14, 2018, Biden said in a statement that his administration will “not wait for the next mass shooting” but will instead “take action” to “end our epidemic of gun violence.”
According to Guns America Digest: “Biden … wants lawmakers to criminalize private transfers, ban many semi-automatic firearms and accessories in common use, and repeal the Protection of Lawful Commerce in Arms Act, which protects the gun industry from being held liable for the criminal misuse of firearms.”
Biden stated: “Today, I am calling on Congress to enact common-sense gun law reforms, including requiring background checks on all gun sales, banning assault weapons and high-capacity magazines, and eliminating immunity for gun manufacturers who knowingly put weapons of war on our streets”.
President Biden is calling for legislation that would ban Modern Sporting Rifles such as the AR-15, shown here as adapted for High Power competition:
The elimination of the Protection of Lawful Commerce in Arms Act could have disastrous consequences for the general shooting sports industry and firearms makers. This is because it would expose gun-makers to civil lawsuits for injuries caused by criminals using guys. As explained by the NRA-ILA:
About the Protection of Lawful Commerce in Arms Act By NRA-ILA
Joe Biden has unveiled his agenda for his first 100 days in the White House, and his list includes an initiative aimed at nothing less than the destruction of the U.S. firearms industry. This is what would happen if Biden succeeds in his pledge to repeal the Protection of Lawful Commerce in Arms Act.
Imagine if firearm manufactures and sellers – even those who strictly followed the laws enacted to regulate their industry – faced potential civil liability every time a criminal misused a firearm. The affect would be similar to holding automobile makers and dealers responsible for injuries caused by drunk drivers. No business, no matter how conscientious and law-abiding, could ever survive being liable for the acts of millions of random people over whom it had no control.
And that is exactly why the law generally imposes no duty on a person or entity to control the acts of third persons to prevent them from causing harm (unless the person or entity has certain types of relationships with those causing the harm or being harmed).
Yet gun control activists in and outside of government hoped to rewrite that principle when it came to the makers and sellers of firearms. During the 1980s and ’90s, a coordinated series of lawsuits against the gun industry sought to hold these businesses responsible for the criminal acts third parties committed with firearms.
This egregious abuse of the legal system to destroy an industry providing constitutionally protected goods and services sparked a bipartisan response from coast to coast. Thirty-four states passed laws to block these suits in their own courts. Finally, in 2005, Congress followed these examples by enacting the Protection of Lawful Commerce in Arms Act (PLCAA) to provide a floor of protection nationwide.
You may have heard the phrase “blueprinting an action”, but do you know what that really means? Do you know what operations are done to an action during the blueprinting process? To help you understand, gunsmith Bill Marr of RifleShooter.com has created a helpful article showing a Rem 700 blueprinting job start to finish. This article spotlights how the procedures can be done with manual tools. Bill, who runs 782 Custom Gunworks Ltd., can also perform many of these operations with modern automated machinery. In fact, Bill has written a follow-up article on Truing a Rem 700 receiver with a Lathe.
Bill explains: “Blue-printing, or truing a rifle action, ensures the receiver face, threads, lugs, bolt lugs, and bolt face are square to the center line of the receiver.” In Bill’s informative article, Bill shows how he blueprints a Remington 700 short action receiver with .308 Win bolt face. He covers the following procedures step by step:
Action Disassembly
Ream Minor Diameter of Receiver Threads
Square the Receiver Lugs
Square the Face of the Receiver
Lap the Bolt Lugs
Square the Bolt Face
We use the bushings to guide the receiver tap. This chases the threads and ensures they are square.
2. Truing the Receiver Face
Using the receiver facing tool, the front of the receiver is trued. The tool is placed over the tap and turned by hand. We used Do Drill to lubricate it.
3. Lapping the Lugs
The bolt lapping tool screws into the front of the action and applies rearward pressure on the bolt face. A little bit of lapping compound is placed on the front of the receiver lugs. The bolt handle is then raised and lowered repeatedly. Note — it is critical that we do not get any lapping compound on any other surfaces.
4. Truing the Bolt Face
On this bolt, the central part of the bolt face was low. After the truing operation, this Rem 700 bolt face is now completely square to the action.
IMPORTANT: Rifleshooter.com states: “This article highlights our project and is presented for information purposes only. This provides an overview of the process and should not be attempted without the guidance and supervision of an experienced gunsmith“.
To err is human… Sooner or later you’ll probably get a case stuck in a die. This “fix-it” article, which originally appeared in the Western Powders Blog, explains how to remove a firmly stuck cartridge case using an RCBS kit. This isn’t rocket science, but you do want to follow the directions carefully, step-by-step. Visit the Western Powders Blog for other helpful Tech Tips.
Curing the Stuck Case Blues
Sticking a case in the sizer die is a rite of passage for the beginning handloader. If you haven’t done it yet, that’s great, but it probably will eventually happen. When it does, fixing the problem requires a bit of ingenuity or a nice little kit like the one we got from RCBS.
The first step is to clear the de-capping pin from the flash hole. Just unscrew the de-capping assembly to move it as far as possible from the primer pocket and flash hole (photo at right). Don’t try to pull it all the way out. It won’t come. Just unscrew it and open as much space as possible inside the case.
Place the die upside down in the padded jaws of a vise and clamp it firmly into place. Using the supplied #7 bit, drill through the primer pocket. Be careful not to go too deeply inside the cartridge once the hole has opened up. It is important to be aware that the de-capping pin and expander ball are still in there and can be damaged by the bit.
Drill and Tap the Stuck Case
Once the cartridge head has been drilled, a ¼ – 20 is tap is used to cut threads into the pocket. Brass is relatively soft compared to a hardened tap, so no lube is needed for the tapping process. RCBS says that a drill can be used for this step, but it seems like a bit of overkill in a project of this nature. A wrench (photo above right) makes short work of the project.
RCBS supplies a part they call the “Stuck Case Remover Body” for the next step. If you are a do-it-yourselfer and have the bit and tap, this piece is easily replicated by a length of electrical conduit of the proper diameter and some washers. In either case, this tool provides a standoff for the screw that will do the actual pulling.
With an Allen Wrench, Finish the Job
Run the screw through the standoff and into the tapped case head. With a wrench, tighten the screw which hopefully pulls the case free. Once the case is free, clamp the case in a vice and pull it free of the de-capping pin. There is tension here because the sizing ball is oversized to the neck dimension as part of the sizing process. It doesn’t take much force, but be aware there is still this last little hurdle to clear before you get back to loading. Don’t feel bad, everyone does this. Just use more lube next time!
Article find by EdLongrange. We welcome reader submissions.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Graf & Sons — Berger Bullets In Stock
⏺ High quality bullets have been hard to find; get these Bergers while you can
Components have been tough to find these days, particularly premium products such as Berger bullets. Head over to Grafs.com where they have a really great supply of Berger bullets in many popular calibers and bullet weights. As always, supplies are limited so don’t wait if you’re in need of bullets.
⏺ Ruger reliability, popular chambering, great camo finish
Here’s a nice 6.5 Creedmoor hunting rifle with a superb camo finish. This Ruger American Go Wild Camo/Bronze Bolt Action Rifle has a coated 22″ barrel chambered for the very popular 6.5 Creedmoor cartridge. It features a Go Wild Camo stock with a Bronze Cerakote barrel finish. There is also a Ruger marksman adjustable trigger all making for a solid hunting rifle for an attractive $589.99 price.
3. Amazon — Lyman Turbo Sonic Case Cleaner, $106.24
⏺ High quality ultrasonic cleaning machine at very good price
Looking for a different way to clean your brass that doesn’t involve dust or loud noises? Check out the Lyman Turbo Sonic Case Cleaner for $106.24. This unit features a heated tank for cleaning of case and primer pockets. The ultrasonic cavitation lifts and dissolves carbon, dirt and any residue left on fired cases. Not only can you clean your brass, but these units are great for other items like jewelry and silverware.
4. Precision Reloading — Wheeler AR Armorers Kit, $128.99
⏺ Great $128.99 Deal for big AR tool kit — sells elsewhere for $242.99!
ARs require a lot of maintenance. And you need some specialized tools to assemble an AR-15 properly — that’s important for guys building their own lowers and uppers. The Wheeler Engineering Delta Series Ultra Armorers Kit includes pretty much all the tools you need to keep an AR15 running well including: AR combo tool, Torque wrench, Strap Wrench and Delta Ring Tool. In addition the kit includes an Armorer’s Vise, Vise Block Clamp, and Armorer’s Bench Block. Supplied in a handy carry case, the Ultra Armorer’s Kit is now just $128.99 at PrecisionReloading.com. This exact same kit is $242.99 at MidwayUSA.
5. Amazon — Frankford Universal Case Trimmer, $79.99
⏺ Smart system fits drills and trims nearly all popular rifle case types
Here is a good option for trimming cases, if you shoot many different cartridge types. Frankford Arsenal Universal Precision Case Trimmer handled most popular cartridges from .17 Rem all the way up to .460 Weatherby. Just choose the right collet then attached the unit to the end of your power drill for fast, easy trimming. The built-in depth micrometer allows for fast trim-length adjustments, and the brass-shaving ejection port ensures a clean trim. The universal collet system indexes on case shoulders for precise and consistent trimming. This trimming system works with just about any 1/2″ power drill.
6. Bullet Central — Hart Barrels Sale
⏺ High quality barrels in stock — no extended wait
Are you putting together a custom rifle but can’t find barrels in stock anywhere? Head over to Bullet Central for a major Hart barrels sale. You can save $20 on every barrel, plus avoid long wait times typically required for a high-quality barrel. A variety of contours are available in popular 6mm and 6.5mm bore sizes, with 1:7″ and 1:8″ twists, all six-grooves.
7. 5.11 Tactical — 20% OFF Everything
⏺ Big Discount on very high quality outdoor clothing and gear
You need good gear to have a successful day at the range or a successful hunt. That means more than have the right guns and ammo — you also need good clothing, packs, and footwear. Here’s a good way to get outfitted properly without breaking the bank.
Right now at 5.11 Tactical you’ll find some of the finest shooting pants, bags, boot, socks and more, all at 20% OFF Savings. This 5.11 20% Off Sale runs through Tuesday, February 15, 2021 at 11:59 pm.
8. Amazon — IRON JIA’S Waterproof Rifle Case, $42.99
⏺ Great rifle protection when it rains or snows; case even floats
There’s nothing worse than being out in the field or at a big match and having it start raining. One way to counteract that is to get a waterproof case like the IRON JIA’S Waterproof Rifle Case. With built in thick foam padding, it protects your rifles from collision damage, also providing buoyancy when it falls in a river or stream. It’s also a great case for those matches where it may or may not rain and you want to ensure your gun stays dry while you’re in the pits.
⏺ Custom-molded ear protection plugs are very comfortable
If you’re tired of ear plugs that don’t fit right or don’t work well then try something new — the Radian’s Custom Molded Ear Plugs. Follow the instructions to mold the materials to creat a perfect, custom fit for YOUR ears. These kits come in various colors. You can also add a Radians lanyard for these custom-molded plugs and a carry case. As with all ear plugs, you can double up with muffs for extra protection. These Radians molded plugs have a 26 dB Noise Reduction Rating — better than most compact muffs.
Here is Tom Mousel with Whitetail taken with his ultra-light hunting rifle fitted with 6mm Creedmoor Lilja barrel. Friend Cody (right) actually took the shot. This gun has a second barrel in 6.5 Creedmoor.
“Light is Right” when it comes to carrying deer rifles long distances in the backcountry. A lighter rifle DOES make a difference when you’re hiking many miles and carrying other gear including binoculars, laser rangefinders, food/water, and packs. And then, if you are successful, you’ll be carrying out game meat, so a lighter rifle translates to a lighter overall load.
When Forum member Tom Mousel (a top 1000-yard competitor) considered a new hunting rifle, he wanted a very light-weight rig. What he got was a low mass masterpiece — an ultra-accurate, five-pound hunting rifle. Not only does this twin-barrel rifle, as built by Alex Wheeler, come in under five pounds (before optics), but it has produced some quarter-MOA 3-shot groups at 1000 yards. The 6mm Creedmoor version of this rifle has demonstrated truly stellar accuracy at long range. The 6.5 Creedmoor barrel also shoots well and packs more punch for hunting use.
CLICK HERE to view full-screen large version of photo.
Here is Tom’s rifle weighing in at 4 pounds, 14 ounces with 21″ Lilja #1 contour 6mm barrel. Tom says: “Here’s the rifle with full Titanium action, bolt, and lug, in a Tom Manners 17 oz. carbon fiber stock. It’s exactly one pound heavier fitted with my Leupold Mark AR 4-12x40mm scope in Talley rings.”
Tom has two barrels for the rifle, one chambered for 6.5 Creedmoor and the other for 6mm Creedmoor. Tom reports: “The 6.5mm is a bit lighter being fluted. But I won’t be switching back now that I’ve shot the 6mm version. Neither has too much recoil, but the 6mm CM just kills the 6.5mm at distance for groups.”
Tom tells us: “What I like about this rifle is there were no corners cut to make it light. On some other ultra-lights, the fore-end has no strength or they are cut down really short. This is a full-sized stock, pillar-bedded with aluminum-filled epoxy and free-floated barrel. The ignition is set up with a TON of firing pin fall to function in the coldest temps.”
Gunsmith Alex Wheeler of Wheeler Accuracy is pleased with how this project turned out: “Tom has shot a bunch of sub-5″ groups and a couple one-inchers back-to-back at 1K. He has the Berger 115gr VLD going about 3050 fps.” Tom noted the 6mm barrel picked up about 50-60 FPS after the first 50 rounds. He shoots 115gr Berger VLDs with CCI 450s and Reloder 16, with the Bergers about .005″-.008″ in the lands.
Groups at 1000 Yards with 6mm Creedmoor Barrel, 115gr Bergers
Here are two of Tom’s 1000-yard targets. This is with the 6mm Creedmoor barrel shooting 115gr Berger VLDs pushed by Alliant Reloder 16 at about 3050 FPS. The average of the two groups is 0.246 MOA. Pretty amazing for an ultra-light rifle shot off a bipod. Tom acknowledges that he can’t do this every day. He says that “shooting 871 yards at my home range, the rifle typically shoots 4″ to 5″ 3-shot groups”.
Q & A with Tom Mousel About his Ultra-Light Hunting Rifle
Q: Why did you choose to build this rig?
Tom: I just wanted to do it to see how light we could build an accurate, good-shooting rifle.
Q: What are your favorite things about the rifle, and is there anything you would change?
Tom: Definitely the light weight, and the overall size — it has a pretty short barrel (21″), so it’s just handy. I wouldn’t change anything about the rifle, now that I have the Titanium bolt. When I bought the action originally it had the steel bolt.
Q: How does this rifle handle?
Tom: It points well considering it is a light rifle. The 6mm Creedmoor version has very little recoil. On a good bipod I can sight in at 1000 without a spotter.
Q: What are your favorite accessories?
I use a Solo Hntr Mtn Lite stretchy cover. You can see it in the photo at right showing me on a hunt. I like this because you can roll it up like a sock and and use it for a rear support.
Q: Why did you choose Alliant Reloder 16 powder?
Tom: Lonnie Anderson, a fellow Deep Creek shooter, did a 6mm Creedmoor and he said RL16 was absolutely the most accurate. We have also found that Reloder 16 is really consistent on velocities through the seasons — from 90 above to teens below zero.
Q: Could this ultra-light set-up work for a bigger caliber also?
Tom: I’ve tried bigger calibers, but I’ve never been satisfied with the consistency of the groups. There’s a cut-off — there’s too much torque and recoil. We see a limit — you don’t want “too much gun” for the platform. Even here, the 6.5 barrel just doesn’t shoot as well as the 6mm.
Q: What advice do you have for hunters considering ultra-light rifles?
Tom: Be careful about falling in love with ballistics and trying to build too much bang for too small a platform. If I built a 7mm WSM for example, I’d want to rifle to weigh at least two pounds more.
Full Titanium Action from Pierce Engineering
This photo shows the Pierce Engineering Titanium Featherweight short action featuring Titanium (Ti) receiver, Ti bolt, and Ti lug. This unit is a mere 15.90 ounces complete. (NOTE: with Titanium body and STEEL bolt the weight is 18.5 ounces). The long action version is 17.4 ounces for the complete Titanium action with Ti bolt and Ti lug.
Jud at Pierce Engineering tells us: “Both the Ti action body and Ti bolt are DLC-coated. This action also has an anti-bind rail for added smoothness and ease of functioning. This really is one of the lightest actions on the market. If you’re looking into building an ultra-light rifle I would seriously check one out! We make these with the highest level of detail, pride, and machining tolerances. They’re just sweet actions… and our Ti Featherweight short action is roughly half the weight of a Remington Model 7. So there’s a significant weight savings with the Pierce Ti Featherweight over a Model 7.”
Owner Profile — Tom Mousel, Hunter AND Long-Range Benchrest Ace
Tom Mousel knows a few things about accurate rifles. He is a top 1000-yard competitor at IBS matches and at the Deep Creek range near Missoula, Montana. In 2016 Tom set a remarkable 6-match Light Gun Group World Record, with a 2.9540″ group size Aggregate for SIX matches. And a year later, in 2017, Mousel set a 10-Match Heavy Gun World Record with a 5.3376″ Aggregate. NOTE: that is for TEN-shot groups in Heavy Gun. That’s an average ten-shot group under 6 inches for 10 matches! Over the past decade, Tom has remained at the top of the 1000-yard game, with many match wins at Deep Creek and other ranges.
Over the past year, large-scale social unrest and calls to “defund the police” inspired millions of Americans to buy their very first handguns. Pistol sales set new records. Americans were looking to acquire handguns for personal protection, both in the home and while away from the house. Thus, many folks are looking for slim, relatively lightweight pistols that can be carried comfortably and discretely. There are dozens of carry guns on the market currently. Here are three good choices, as reviewed by our friends at GunsAmerica.com. In this article, we cover three of the best “micro-compact” 9mm pistols: SIG Sauer P365, Smith & Wesson Shield, and the Glock 43.
After looking at a variety of factors, including accuracy, reliability, ergonomics, build quality, size/weight, and price, GunsAmerica’s tester Jeff Cramblit concluded that the SIG P365 was the best of the three: “Bottom Line — The SIG P365 wins this shootout in my humble opinion. The MSRP of $599 is a bit higher than the other guns but SIG brings a bit more to the game. The outstanding grip design, higher capacity, great sights, lighter trigger pull, smaller length, light weight and just a great overall feel make it a winning product. The other two guns are great, they have been the cornerstones of concealed carry for many years, and I have personally carried both of them, but SIG has changed the game.”
Choosing a Carry Pistol — Performance, Reliability, Value
This Editor owns two SIG Sauer pistols, a P226 and P232. Both are “old school” metal-framed handguns. I can attest to their quality and reliability over many years. So I’m not surprised to see that SIG’s new P365 took top honors in this recent test. But I also think the Smith & Wesson Shield also offers excellent value for the dollar. The S&W 9mm Shield is ON SALE now for $289.99 at Palmetto State Armory.
This YouTube Video Compares the SIG P365 and the S&W Shield
Accuracy with Various Ammo
In the GunsAmerica Test, the SIG P365 had the best accuracy, based on five (5) different types of 9x19mm ammo shot off-hand at 25 yards. The SIG’s average 5-shot, 25-yard group size was 1.45″, vs. 1.7″ for the Glock 43, and 2.1″ for the S&W Shield. The P365’s accuracy edge may be due in part to its lighter, 5.1-lb trigger pull compared to 6 lbs. for the S&W Shield, and 6.25 lbs. for the Glock 43.
Dimensions — Width and Weights
Size matters — particularly when it comes to a carry pistol. The S&W Shield is the narrowest of the three guns at 1.03″ wide vs. 1.11″ for the P365 and 1.36″ for the Glock 43. Though it has the highest round capacity, the SIG P365 actually has the smallest grip circumference and grip depth. Weight-wise, the Glock 43, at 18 oz. unloaded, is the lightest. The SIG P365 is 18.8 oz., while S&W Shield is the heaviest at 20.5 oz. weight.
Capacity — SIG P365 Has the Edge
The SIG P365, holding 10+1 rounds, has the highest ammo capacity. This is remarkable as the P365 has the smallest grip circumference of the three pistols. Kudos to SIG for clever design. The S&W Shield has an 8+1 capacity, while the Glock 43 only holds 6+1. Advantage SIG.
Sticking a case in the sizer die is a rite of passage for the beginning handloader. If you haven’t done it yet, that’s great, but it probably will eventually happen. When it does, fixing the problem requires a bit of ingenuity or a nice little kit like the one we got from RCBS.
Q: Why did you choose to build this rig?
Dimensions — Width and Weights
