Photos by Stephen Fiorenzo, courtesy Applied Ballistics.
The 2017 King of 2 Miles match has concluded, and we have a new monarch. F-Class Ace Derek Rodgers is the new King of 2 Miles. Shooting with Team Applied Ballistics, Derek delivered a dominant performance, scoring nearly twice as many points as his nearest rival, Ronnie Wright. And Derek was the first KO2M marksman in history to hit the target at the maximum 3368-yard (1.91 mile) distance.
With his McMillan-stocked .375 CheyTac rifle, Derek shot brilliantly from the start. He was perfect — without a miss — at the first three yardages: 1543, 1722, and 1888. He had some misses at 1953 and 2667 yards, but then he out-shot all competitors at 3028 yards, going two for five. No other shooter managed a single hit at 3028 yards. Then it all came down to the big one — the last (and greatest) challenge, the target at 3368 yards (1.91 miles).
This would require superior shooting skills, a masterful wind call (by Emil Praslick), and nerves of steel. Derek tried four shots without success. It looked like the two-mile hit would continue to be an impossible goal. But then, on his fifth and very last shot, Derek did it — he hit the 3368-yard target.
After Derek made the (nearly) two-mile shot, cheers erupted on the firing line — what an achievement! Derek is the first (and only) shooter to make the 3368-yard shot at K02M. Watch him do it in this video:
Derek Rodgers Hits Target at 3368 Yards on his Final Shot:
Derek Rodgers K02M-Winning Hardware and Ammunition
Factory Rifle Finishes in Second Place
With so many full-custom rifles on the firing line, many were surprised to see a factory rifle finishing second overall. Ronnie Wright shot superbly with his stock Barrett M99 chambered in .416 Barrett. Ronnie’s impressive second-place performance proved the effectiveness of the .416 Barrett cartridge (and the build quality of the M99). For ammo, Ronnie used Cutting Edge 472gr MTAC projectiles loaded in Barrett-stamped .416 cases. The powder was Alliant Reloder 50 ignited by CCI #35 50 BMG primers. The rifle had a Barrett factory 32″ barrel fitted with an Accuracy 1st level.
INTERVIEW with DEREK RODGERS:
Q: What do you believe contributed to your success at this match?
Derek: This match was truly a team effort from the entire Applied Ballistics Team. Emil Praslick and Paul Phillips are world class wind-readers and spotters. They have the ability to make decisive decisions and trust that I (as the shooter) will put a bullet on target every time a command is given. We posses a dynamic team background with a lot of history and experience under our belt. Our positive team synergy is hard to find. The addition of vital tools played a huge role in our success. A few of the tools we used were the AB Kestrel and Garmin Foretrex 701 AB Elite to give absolutely crucial and accurate ballistic solutions. The new McMillan ELR Beast stock was stable and the NF ATACR scope is robust and clear. The Bartlein barrel used was top notch! However, one of the most important pieces of the ELR puzzle and the only thing that separates the target is — the bullet. We chose Cutting Edge (CE) bullets due to their high level of precision. These bullets proved to be invaluable in connecting every piece of steel at the KO2M competition. The CE 400gr Lazer Max bullet was selected and was tremendously accurate. This bullet transitioned into a sub-sonic velocity without any loss of precision at ELR distances. Our success would not be possible if the projectile did not fly correctly for 7+ seconds of flight time. CE has outstanding designs and several quality choices to choose from.
Q: How many hours would you say you practiced for this match?
Derek: It is hard to calculate practice time in hours. ELR is a program that we work on every chance we get — day and night for months prior to the event. We have an extremely strong background of team shooting and long range shooting. A lot of time has been invested on and off the range, but does not stop there. The combined range time from other disciplines really helped me to be successful in transitioning from long range to ELR. It really is a compilation of 10 years of trials and tribulations. Some would say, “the Devil is in the details”. Our team tries very hard to not overlook any small detail. Practice and training is always scrutinized for improvements. Our Applied Ballistics team has a love and passion that goes beyond measurable amounts of time. We were fortunate to get together for two days a month prior to the Ko2M event to review our program and practice as a team. Bryan Litz had a plan, and we discovered as a team we had flaws in our program. Each one of us contributed from years of experience on improving our technique until we had a winning solution.
Q: Why did you choose the .375 CheyTac cartridge?
Derek: When I was asked to join the AB Team, I needed to get an ELR rifle built in a short period of time. I was under a very tight time schedule to get the project complete. In an effort to eliminate variables, I decided to keep things standard and as simple as possible. I chose the .375 CheyTac for the ease of getting components. The larger rifles are more difficult to get components quickly and I felt like the .375 CheyTac had enough attributes to be competitive at ELR distances.
The Cutting Edge 400gr bullets are milled from solid copper bar stock on a CNC Swiss-style lathe.
New ELR Hardware and Software on Display at K02M
This marks the second straight year that Team Applied Ballistics has won the K02M event. Last year, Team AB shooter Mitchell Fitzpatrick won the coveted “King of 2 Miles” title (Fitzpatrick finished fourth this year, just off the podium). In the past year, there has been considerable evolution in Extreme Long Range hardware and software, and projectiles are constantly being improved.
Bryan Litz (center) conferring with Team AB members Emil Praslick (L) and Doc Beech (R).
We asked Bryan Litz, founder of Applied Ballistics, to summarize developments in the ELR game. Here are Bryan’s observations:
“Each year the KO2M sees advancements and shooters converging on those tools and processes that have proven effective in prior years. It’s rather apparent, for example, that spotting impacts is a crucial part of success in this match. This was improved by the match directors/organizers placing the targets in very good locations for spotting impacts. We’re seeing less set-ups with adjustable bases, and more with solid/fixed scope mounts. One of the exciting new pieces of equipment is the periscope device made by TACOMHQ (John Baker). This device provides an optical shift to the image which allows you to get more elevation for those long shots. Also, the refinement of fire control (ballistic) solutions has really played a role in getting shooters centered up for their first shots.”
“This tournament highly favors first-round impacts with the scoring system, so the approach of ‘walking the shots on’, isn’t a winning strategy. Those who employed accurate ballistics solvers were able to score more first round hits, and pile up the points. First and second place (at least) were using Applied Ballistics solvers to center their shots. We’re looking forward to even more advancements and making these ELR shots even out to two miles more commonplace in the future thru systematically applying the Science of Accuracy.”
The winning Applied Ballistics Team:
Bonus Video — Interview with David Tubb at KO2M
Share the post "King of 2 Miles ELR Match — Derek Rodgers Takes the Crown"
Report by Corbin Shell
Not long ago, I learned of the King of 2 Miles (KO2M) shoot held in Raton, NM and was fortunate enough to get an entry slot. I will be shooting with David Tubb, multi-time High Power and Long Range National Champion, on a team we call the “Second Amendment Cowboys”. Given such short notice, I scrambled to find the necessary components to build a suitable rifle for the event. I turned to longtime friend and owner of X-Treme Shooting Products (XTSP), Tom Myers, to see if he might have a suitable action. XTSP is known for its premium titanium rifle receivers, however XTSP also manufactures stainless actions. As luck would have it, Tom was completing a small run of .338 Lapua Magnum-sized stainless steel single-shot actions. Other components were sourced as quickly as possible and the building began in earnest.
Before acquiring the first component for this build I already knew who was going to perform the work, Doyle Anglin at Dixie Guns, inc.. Doyle’s attention to detail and rifle building knowledge is second to none! I came to Doyle with the idea of building a rifle to shoot in the King of 2 Miles match and his ears perked up. Once all the components were in hand Doyle began construction. Doyle was given free liberty to build whatever he felt best for the job given the time constraints and components that were readily available on such short notice. I cannot thank Doyle Anglin enough for the stellar job he did!
KO2M .338 Lapua Magnum Improved — Rifle Components
— Custom laminated stock Doyle Anglin designed and created from scratch
— 10″-long aluminum barrel block designed and made by Doyle Anglin
— XTSP (X-Treme Shooting Products) PH420 stainless single shot receiver 1.450” diameter. PVD-coated receiver body. FNC-coated one piece bolt.
— XTSP +35 MOA and +60 MOA tapered Picatinny rails, PH420 stainless, PVD-coated
— XTSP two-stage trigger with safety
— Krieger 1:9.3″-twist barrel. 1.450” for 6.5” tapering to 1.100” at the muzzle. 33.5″ finished length
— Piercision Rifles 3/4×24 slab-sided, 5-port muzzle brake
— BAT stainless trigger guard
— Masterclass cheek piece with extended rods
— Masterclass butt plate hardware
— Duplin Bipod
— Spuhr +20.6 MOA one piece scope mount
— Ivey +175 MOA adjustable scope mount
— Sightron SIII 6-24x50mm MOA-value scope (100 MOA of total travel)
— Geier & Bluhm 10 minute precision bubble level mounted to barrel block via extension rod
— Manson .338 Lapua Magnum Improved 30-degree reamer, .375” neck diameter
Load Information
— Sierra 300 grain MatchKing, meplats trimmed and pointed, seated .010″ into lands*
— Hodgdon Retumbo Powder, 101 grains
— Peterson .338 Lapua Magnum brass
— Federal 215 primers
— Jim Carstenson custom reloading dies: inline seater, full-length bushing, neck bushing and threaded micrometer seating die
This load has achieved 3050fps with low single-digit SDs
Given the 12-pound barrel weight, Doyle strongly suggested a barrel block to offer additional support and increase rigidity. Doyle created a split ten-inch aluminum barrel block and mating steel plate that is inletted into the forend of the custom laminated stock. The 1:9.3″-twist Krieger barrel is epoxied into the barrel block as well as being held in place by the ten socket head cap screws. Two hardened and ground pins locate and index the barrel block onto the steel mating plate. The steel mating plate acts as the recoil lug which mates up to the cut on the reward section of the barrel block. The Krieger barrel is chambered with a 30-degree Lapua Magnum Improved reamer and throated accordingly, yielding a loaded round of approximately 4.000 inches.
The barrel is capped with a very effective Piercision Rifles 3/4×24 slab-sided, five port muzzle brake. The size proportions of the muzzle brake work well with the 1.100” muzzle diameter, however it will work on barrels up to 1.450″ in diameter.
Doyle Anglin worked his creative magic and constructed the multi-color laminated stock from a blank. The five inch fore-end allows the rifle to be utilized in a dual role — either benchrest or prone with bipod. The cheek piece hardware is from Master Class Stocks and is adjustable for cast on/off with preset elevation settings via half-moon shaped clips. The two-way adjustable butt plate hardware also comes from Alex Sitman at Master Class Stocks. The multi-colored laminate stock is clear-coated with special marine UV inhibitor paint. The glass smooth finish makes the wood appear wet and is extremely smooth to the touch.
Lots of Elevation on Tap with Angled Rails, Spuhr and Ivey Mounts
Topping off the rifle is either a +35 or +60 MOA X-Treme Shooting Products Picatinny scope rail. The receiver and scope rails are pinned for accurate repeatability when interchanging. Five 8×40 socket head cap screws firmly hold the scope rail in place. A SPUHR +20.6 MOA tapered, one-piece scope mount securely grasps the Sightron SIII 6-24x50mm MOA scope. I cannot say enough good things about the quality of the SPUHR scope mount! This is the only fixed scope mount that I will use going forward and a special thanks goes out to Ulf at SPUHR! The 35 MOA rail and 20.6 MOA SPUHR mount setup allows full utilization of the Sightron’s 100 MOA of internal travel. The second scope setup is comprised of an Ivey +175 MOA adjustable scope base and Sightron SIII 6-24x50mm optic.
Scope in SPUHR mount shown below:
Scope in IVEY Mount with barrel block-mounted precision bubble level:
When shooting extended long range (ELR) it is important that the scope’s crosshairs remains level. Should the crosshairs be canted it will induce impact shift which increases with the angle of cant and distance. The decision was made not to use any of the lesser quality/precision bubble levels that currently flood the market. These levels have poor resolution usually between one and two and a half (1-2.5) degrees. It must be noted that not all levels are created equal. The fine folks at Geier & Bluhm offered up a solution with a precision glass vial horizontal level with an accuracy of ten minutes. As a refresher, one degree is comprised of 60 minutes of angle. The level setup we chose for this rifle is, at minimum, six times more accurate than the best scope or picatinny level on the market. The 10 MOA bubble level sensitivity is just about perfect and does not create a situation of having to “chase” the bubble left and right when in position.
A portable 150 MOA tall target was created to test both scope tracking and crosshair alignment. When testing at the local 100-yard range I got a lot of strange looks and a few inquiries as to why in the world was I shooting thirteen FEET above the aiming bullseye.
As the F-TR shooters have learned, it is very important that the rifle travel freely and repeatable under recoil. I turned to Ray Gross who custom made a rubber and Cordura shooting mat which the bipod rides on. This mat is of the same material and construction that most of the F-TR team is utilizing. The rubber durometer is correct so the rifle does not bounce or hop when fired. The bipod skis slide very easy on the Cordura-topped mat. A big thanks goes to Ray Gross for assisting with the mat setup. In addition, high molecular weight polyethylene (HMWPE) tape was applied to the butt stock of the rifle. The HMWPE tape allows for extremely low friction between the butt stock and rear sand bag. This configuration tracks very well and slides rearward like it is on rails.
As load development progressed I tested three different brands of projectiles. A ladder test was performed at 300 yards to determine where the node was with my barrel and powder combination. The rifle liked between 99-101 grains of Hodgdon Retumbo. I then proceeded to shooting ten shot groups at 1000 yards. In this rifle the Sierra 300gr Matchking was hands down the winner for smallest groups and the best elevation at 1000 yards. The load settled on is 101 grains of Retumbo and 300 grain Sierra Matchking. 500 Sierra bullets were measured base to ogive and the spread over the entire 500pc measured .003” with 490pc varying by .001”. Keep up the good work Sierra Bullets! A special thank you goes to John Whidden for generously allowing me to come to his shop and repoint the Sierra .338 projectiles and allowing me to test at his 1000 yard range.
Preparation for the King of 2 Miles match has been a great learning experience and a lot of fun! Next year’s rifle design is already in the works and should be an over the top build. Stay tuned to AccurateShooter.com for further details!
* The Sierra 300gr MatchKings were meplat-trimmed and pointed using the original pointing system made by Ferris Pendell for Jim Hardy. A big thank you goes out to John Whidden for allowing me to come to his shop and use the original bullet pointing system.
Share the post ".338 Lapua Magnum Improved Barrel Block Beast for K02M"
Shooter behind the .375 Lethal Magnum. Check out the size of that suppressor!
Two-Mile ELR Training The Applied Ballistics ELR Team spent the weekend at the NRA Whittington Center in New Mexico training for the upcoming King of 2 Miles event. Former USAMU coach Emil Praslick III was on hand to help with wind calls. The results were impressive — all team members had confirmed hits at 2.05 miles on a 36″x36″ steel target. Bryan Litz even had a 3-shot group that measured 17.5″ x 22″. That’s under 0.6 MOA!
Most guys would be happy with 0.6 MOA at 300 yards. Bryan did it at 3611 yards, shooting Paul Phillips’s .375 Lethal Magnum. When you consider all the variables involved (bullet BC variance, shot velocity variance, wind changes during flight, Coriolis effect etc.), that’s phenomenal.
Report by Paul Phillips
Just got done shooting two days in New Mexico with Recoil Magazine and the Applied Ballistics ELR team. We learned a lot and had great success. Every team member made impacts on target at 2 miles. The best 3-shot group at 3611 yards (2.05 miles) was shot by Bryan Litz with my 375 Lethal Mag. The group measured 17.5 inches tall by 22 inches wide with Cutting Edge bullets. We also had Recoil’s David Merrill shoot at two miles and was laying them in there like a true pro. We had three team members make impacts on the 36-inch plate at two miles within just three attempts in a mock competition. I also increased my personal longest shot by hitting only 15 inches right of center at 3611 yards. 2.05 miles. I did it with a GSL Technology Copperhead Silencer.
Report by Emil Praslick
I participated in the Extreme Long Range training with the Applied Ballistics team at the Whittington Center in Raton, NM. All team members had confirmed hits at 2.1 miles. Components and hardware suppliers included: Berger Bullets, Cutting Edge Bullets, Nightforce Optics, Kestrel, FLIR Systems.
Q: At that distance (2.1 miles), how much do spin drift and the Coriolis effect impact bullet trajectories?
Praslick: At 3613 yards we had to adjust about 1.5 MOA/56″ of Coriolis (up), and 5 MOA/~190″ of right spin drift adjustment. You’d have to come down if facing East. The planet rotates counter-clockwise (from above), so your target would be falling away from you.
Here is a 3-round group at 1898 yards (1.08 Miles) shot with factory ABM Ammo .338 Lapua Magnum loaded with 300 grain Berger Bullets Hybrids. That’s sub-MOA elevation. (The guy calling wind didn’t do too bad, either.)
Report by Bryan Litz
Learning is my favorite part of new ventures and we learned a LOT this weekend shooting extreme range in New Mexico. I connected on a second round hit on a 3-foot square target at 2 miles in simulated match conditions under coaches Emil Praslick and Paul Phillips. In fact all five of our team shooters got on at 2 miles. The Applied Ballistics Extreme Long Range team is in good shape for the King of 2 Miles match later this month, and there is still so much to LEARN!
You need serious equipment for shooting beyond two miles. Who can identify this high-tech hardware?
Share the post "Extreme Long Range Training — Rockin’ Two Miles at Raton"
Serious ammo — .375 Lethal Magnum rounds loaded with 400gr Cutting Edge Lazer bullets. One wag posted “They look like SCUD missiles.”
In the Extreme Long Range (ELR) game, great ballistics are paramount, but you also need excellent accuracy. The top ELR shooters campaign large-caliber rifles that boast truly remarkable accuracy, considering the massive cartridges they’re shooting (with 160+ grains of powder). These big boomers, such as the .375 Lethal Magnum shown above, can really hammer.
The winner of the 2016 King of 2 Miles (KO2M) event was Mitchell Fitzpatrick, shooting a .375 Lethal Mag cartridge, as part of Team Applied Ballistics. Another member of that squad, Paul Phillips, is also campaigning a new rifle chambered for the .375 Lethal Magnum. Paul was recently doing load development for his new beast, which features a McMillan stock, Nightforce scope, and Phoenix Bipod. Among his barrels for this rig is a massive, 38″-long Bartlein.
“I had a great time today doing load development at Applied Ballistics LLC laboratory with Bryan Litz, Bill Litz, and Mitchell Fitzpatrick. I was testing loads for my .375 Lethal Mag built by Lethal Precision Arms LLC. The last several test groups were sub half-min at 300 yards. Next testing is at 1800 yards.” — Paul Phillips
For this test, Paul’s load featured 400gr Cutting Edge Lazer bullets launched at a blistering 3290 FPS with Hodgdon H50BMG powder. Looks like Paul got his load dialed in “good and proper”. He fired a 0.9″ group at 300 yards, and the Oehler System 88 chronograph showed a very low Extreme Spread (ES) of just 5 FPS. That’s impressive even for just three shots.
A little snow on the ground can’t stop the Applied Ballistics testing team…
Look carefully and you’ll find the powder charge weight — a bit more than you’d load in a 6PPC…
Bryan Litz inspects the .375-caliber barrel with bore-scope.
Share the post "Big Boomer Load Dev — .375 Caliber 400 Grainers at 3290 FPS"
Kelly McMillan with his lastest creation — the “ELR Beast”.
The design team at McMillan Fiberglass Stocks is working on a new heavy-duty stock for the Extreme Long Range (ELR) game. This beefy gunstock is designed to handle the heavy torque and recoil of big-caliber cartridges such as the .408 Cheytac and .50 BMG. The stock is also designed to balance the ultra-long barrels favored by ELR shooters and King of 2 Mile competitors. Shown above is the boss-man himself, Kelly McMillan, with the new ELR stock prototype. Kelly calls this “the ELR Beast”. Note how the cheekpiece is slotted to allow unimpeded movement of the extra-long bolt.
Kelly tells us: “Making headway on the ELR Beast. Using Paul Phillips’s barrel and action we have been able to make some progress in both the design and the cosmetics of the stock. I am pleased with where we are at this time. As is, this set up weighs 46 pounds, I suspect we can get this stock to weigh between 8 and 9 pounds maximum, and maybe 5 pounds minimum.”
Share the post "Beast in the Works — New ELR Stock from McMillan"
With the success of the King of 2 Miles (KO2M) event and the growing popularity of extreme long range shooting, we’ve seen an increased interest in really big cartridges for really long range. One such wildcat cartridge is the 300 Raptor pioneered by Kirby Allen. This monster magnum can launch a 230gr bullet at 3350 fps. That delivers some serious ballistics at extreme long range.
Kirby Allen of Allen Precision Shooting, www.apsrifles.com, has developed a .30-caliber, jumbo-sized magnum wildcat cartridge. The powerful 300 Raptor (center in photo) is based on Allen’s 338 Excalibur parent case (far right in photo), necked down to 30 Cal with shoulder moved forward to increase case capacity. Allen states: “This is the largest capacity and performance .30 caliber magnum on the market that can be used in a conventional sized receiver.”
Shoot 200s at 3600 fps
Performance of Allen’s new 300 Raptor is impressive. Allen claims that “200gr Accubonds can be driven to nearly 3600 fps, 230gr Berger Hybrids to 3350 fps, and the 240gr SMK to right at 3300 fps. These loads offered case life in excess of 6-7 firings per case and many of my test cases have over 8 firings on each case so they are not an overly hot load showing the potential of this big .30 caliber.”
To showcase the new cartridge, Allen built up a prototype rifle with a McMillan A5 stock, Raptor LRSS Action with extended tenon, and a Jewell trigger. The first 300 Raptor Rifle is currently on its second barrel, a new 30″, 3-groove 1:9″-twist Lilja in a custom APS “Raptor Contour”. This distinctive dual-fluted contour runs full-diameter almost to the end of the stock, and then steps down and tapers to the muzzle, where a beefy Medium 3-port ‘Painkiller’ Allen Precision brake is fitted.
Story tip by EdLongrange. We welcome reader submissions.
Share the post "Is the 300 Raptor the Ultimate .30-Caliber Magnum?"
Are you a died-in-the-wool .50 BMG fan? Got a hankerin’ for heavy artillery? Then visit the FCSA Photo Gallery page. There you’ll find hundreds of photos from Fifty Caliber Shooting Association (FCSA) matches and 50 Cal fun shoots in eleven states plus Australia, Switzerland, and the United Kingdom. To access the photos from the Gallery Page, start by selecting a state/country and then click on the colored buttons for the event date (e.g. 2015-04).
Photo sets go all the way back to 2002, so you can see the evolution of the hardware over the years. Sample multiple archives to see the differences in terrain from one range to another — from Raton’s alpine setting to the hot, dry Nevada desert. This Gallery is really a treasure-trove of .50-Cal history. Here are a few sample images.
Story Tip from EdLongrange. We welcome reader submissions.
Share the post "Photogenic Fifties — FCSA Photo Galleries"
Extreme Long Range — 2477 Yards
Notably, two Applied Ballistics team shooters made hits at 2477 yards. Just how far is that? Take a look at the photo above — that shows the location of the 2477-yard target with the firing line in the far distance. Now THAT is truly long range!
By Paul Phillips
I wanted to share a video that I made. This was from the King of 2 Miles event held recently in Raton, New Mexico. I was fortunate enough to be apart of an amazing team with Bryan Litz and Mitchell Fitzpatrick. We had some awesome sponsors: Berger Bullets, Nightforce Optics, McMillan Group International, Lethal Precision Arms LLC and Applied Ballistics LLC. Team Applied Ballistics took First, Second, and Fourth places out of 38 teams in this competition. Our Team highlight was working together to make first-round hits on a 24×36 inch plate at 1.4 miles. With me as coach, both Mitchell and Bryan made their first-round hits at 1.4 miles (2477 yards to be exact).
Video Shows Team Accomplishing Hits at 2477 Yards in Raton, NM
This event has been a personal goal of mine for a long time and I wanted to thank Bryan Litz and Mitchell Fitzpatrick for having me on the team. I call them quiet professionals. I also wanted to thank Kelly McMillan for sponsoring our team and being involved. Kelly has been an amazing sponsor and advocate for shooting sports and providing stocks and rifles for our military snipers for the past 40 years. I can’t forget to thank Ian Klemm for loaning me his Vortex Spotting scope with the MOA milling reticle. It worked great and was very fast to make corrections along with good glass.
Mitchell Fitzpatrick won the KO2M finals to earn the title “King of Two Miles”. He had a dominant performance shooting a .375 Lethal Precision Arms LLC rifle loaded with prototype solid 400gr Berger bullets. Mitchell built this rifle himself using a McMillan A5 Super Mag stock. Note: Berger has no current plans to market this .375-caliber bullet — it is still in the prototype stage.
Editor: Paul Phillips asked to make a special dedication, remembering a family member: “My brother Daniel Phillips passed away with brain cancer last year and this event was one that he wanted to video for me. I know he is smiling in heaven.”
Share the post "Phillips Video Shows Highlights of King of Two Miles Competition"
The Applied Ballistics ELR Team spent the weekend at the NRA Whittington Center in New Mexico training for the upcoming King of 2 Miles event. Former USAMU coach Emil Praslick III was on hand to help with wind calls. The results were impressive — all team members had confirmed hits at 2.05 miles on a 36″x36″ steel target. Bryan Litz even had a 3-shot group that measured 17.5″ x 22″. That’s under 0.6 MOA!
Kirby Allen of Allen Precision Shooting, 
