|
|
June 19th, 2017
After 56 years Pat Farmer was reunited with the M1 Garand he used while serving his country.
By Ashley Brugnone, CMP Writer
Pat Farmer hadn’t felt the weight in his hands in 56 years. After five decades, the memories flooded back as his fingertips grazed the wood of the stock and gripped it tightly. It was a piece of his personal history, and the history of his country… and now, it’s a relic he’ll be able to keep for the rest of his life.
“I had never dreamed it would be in the CMP (Civilian Marksmanship Program) warehouse,” he said. “I had just hoped to possibly start a search beginning with the CMP.”
The 74-year-old from Jacksonville, NC, is a retired veteran who served 26 years in the armed forces. He was raised on a farm in Nebraska where he became familiar with guns at an early age. As a teen, he enlisted in the U.S. Marine Corps during his senior year in high school through a delay program. On August 30, 1960, he left for the Marine Corps Recruit Depot in San Diego, California, to attend boot camp — where he celebrated his 18th birthday.
Upon arrival he was issued M1 Garand #4305638. The firearm soon became a close companion as he spent countless hours with it on the “Grinder” — a Marine Corps term for a deck or parade ground used for drill and formations.
Reunited with M1 Garand after 56 Years
On May 8, 2017, Pat Farmer was reunited with M1 Garand #4305638 thanks to the CMP. Bringing it back to life, Pat began to fieldstrip the rifle. As he got to the trigger housing of the gun, he found something that he couldn’t believe – tape with his name and markings on it. It read, “Farmer 20/8L.” Pat believes it was his 500-yard “dope” – twenty clicks elevation, eight clicks left windage.
“Fifty-six years ago, we drilled and did the manual of arms with M1s as if they were matchsticks. It seems much heavier now!” Farmer added with a laugh.
Pat was eventually selected for aviation school after infantry training and shot on the rifle team while attached to a Reserve unit. He went on to shoot expert rifle at the Camp Mathews rifle range*. “It was some of the best and most rewarding years of my life,” he said.
Many years later, Pat one day went through an old locker box and found his custody receipt from Jan. 27, 1961, when he turned in his boot camp rifle before transferring to aviation school. Curiosity set in as he wondered whatever became of M1 Garand #4305638 – and the idea of finding it overcame him.
“I had purchased a few rifles from the old DCM and also CMP, so on a whim I decided to contact CMP to see if my old M1 had ever passed through their system,” he explained. Here’s the story of what happened and the years of waiting…
Share the post "“This is My Rifle” — 74-Year-Old Marine Reunited with M1 Garand"
April 12th, 2017
Big news for M1 Garand fans. The CMP recently announced that it should be receiving 86,000 M1 Garand rifles from the Phillipines. These WWII-era battle rifles were originally loaned to the Phillippines government through a Military Assistance Program. As “loaners”, they could eventually be repatriated to the United States. It looks like these old rifles will finally be coming home.
The return of the surplus Garands was disclosed last week by Gina Johnson, Gen. Mgr. of CMP South (Alabama). Posting on The M-1 Garand Enthusiasts Group Facebook Page, Ms. Johnson wrote:
“ … CMP will be receiving the rifles once the Phillipines prepares them for shipment. CMP reimburses the Army transportation costs of getting these rifles back as they have with every other shipment sent to us. We do not know when these rifles will be shipped back, but they have been approved.”
This was later confirmed by Mark Johnson, Chief Operating Officer of the CMP. Johnson stated that the rifles could be shipped back for distribution to American civilian shooters: “There are 86,000 or so M1s hopefully coming back to the Army,” he said. “We hope to see them in the future.”
These historic rifles can be returned to the USA and the CMP because the rifles were originally loaned to the Phillipines government through the Military Assistance Program, a more modern version of the “Lend Lease” program that provided arms and assistance to U.S. allies during WWII. Alloutdoors.com explained: “Since these rifles were loaned, not purchased outright, they are eligible for return to the U.S. Army and then the CMP”.
Condition and Price “To Be Determined”
As the CMP has not yet seen or graded the M1 Garands, the typical condition of the rifles remains unknown. But with so many rifles coming back the the USA, we can expect there will be some in very fine condition. It make take a long time for the CMP to inventory all 86,000 Garands and eventually list them for sale on the CMP Store.
Share the post "CMP Announces Repatriation of 86,000 M1 Garands"
December 21st, 2016
NRA President Allan Cors’s favorite firearm is this unique M1 Garand, originally given to John C. Garand by the Springfield Armory. Images courtesy NRA Museum (top) and NRA Publications.
NRA President Allan Cors has a very special M1 Garand in his firearms collection. This unique M1 rifle was originally owned by none other than its inventor, John C. Garand. This historic Springfield Armory M1 rifle bears the serial number 1,000,000. This rifle, which came complete with a walnut-fitted case, silver-plated clip and gold-plated cartridges, was originally presented to its designer John C. Garand as a retirement gift in 1953. Remarkably, this gift was the only reward the famous gun designer received for his contribution to the Allied victory in the Second World War.
Read Full Story on NRABlog.com.
Upon his passing, Garand’s family offered the rifle for sale. As the M1 was one of his passions and realizing the extraordinary historic significance of this particular gun, Allan Cors made an offer on the M1. The Garand family accepted.
“I felt very good that they trusted me to do the right thing. Let’s face it: we are only temporary custodians of these things,” Cors said. “They are here in our hands for a while, and then they are passed on to the next generation.”
About John C. Garand
Jean Cantius Garand (January 1, 1888 – February 16, 1974), also known as John C. Garand, was a Canadian designer of firearms who created the M1 Garand, a semi-automatic rifle that was widely used by the U.S. Army and U.S. Marine Corps during both World War II and the Korean War. Garand’s fondness for machinery and target shooting blended naturally into a hobby of designing guns, which however took a more vocational turn in 1917. That year the United States Army took bids on designs for a light machine gun, and Garand’s design was eventually selected by the War Department. The U.S. government employed Garand as an engineer with the Springfield Armory from 1919 until he retired in 1953.
 Credit: NPS Photo, public domain
In Springfield, Massachusetts, Garand was tasked with designing a basic gas-actuated self-loading infantry rifle and carbine that would eject the spent cartridge and reload a new round based on a gas-operated system. Designing a rifle that was practical in terms of effectiveness, reliability, and production, stretched over time; it took fifteen years to perfect the M1 prototype model to meet all the U.S. Army specifications. The resulting Semiautomatic, Caliber .30, M1 Rifle was patented by Garand in 1932, approved by the U.S. Army on January 9, 1936, and went into mass production in 1940. It replaced the bolt-action M1903 Springfield and became the standard infantry rifle known as the Garand Rifle. During the World War II, over four million M1 rifles were manufactured. The Garand Rifle proved to be an effective and reliable weapon and was praised by General MacArthur. General Patton wrote, “In my opinion, the M1 rifle is the greatest battle implement ever devised.” Source: Wikipedia.com.
Share the post "John C. Garand’s Garand — Springfield M1 Number One Million"
November 22nd, 2016
Want to build your own accurized M1 Garand? Then consider signing up for the CMP’s Advanced Maintenance Class (AMC), a 3-day program for students with mechanical aptitude and a desire to work on M1 Garand rifles. Each student will assemble his own CMP Special M1 Garand Rifle with a USGI receiver. This will be a “keeper” Garand that the AMC student takes home. Total cost for the 2017 AMC is $1830.00, which includes the cost of the rifle ($1030.00) plus tuition charges. Students must provide their own accommodations in Anniston, Alabama.
Registration is open for the Civilian Marksmanship Program’s (CMP) 2017 Advanced Maintenance Clinics. Interested persons may register now through December 2, 2016. NOTE: If you are interested in this program, apply soon — all spots in last year’s classes filled up quickly.
Each 3-Day Advanced Maintenance Class will be led by highly-qualified Custom Shop staff members. On the third day, students will visit the Talladega Marksmanship Park as VIP guests of the CMP. At Talladega, each AMC student will have a chance to fire the M1 Garand they built in the class, shooting at Talladega’s high-tech electronic targets.
CMP 2017 Advanced Maintenance Class (AMC) dates are:
January 24-26; January 27-29
March 14-16; March 17-19
August 15-17 (Buddy Class); August 18-20 (Buddy Class)
October 24-26; October 27-29
This class is not intended for gunsmiths — no prior armorer experience is required. Students will assemble their own CMP Special rifle, which is included in the $1830.00 fee. Class topics will include:
– Commercial barrel installation, chambering, and headspace
— Component function, selection, and inspection
— Fitting and proper assembly of a complete CMP Special rifle
— Discussion of malfunctions and their remedies
— Accurizing techniques for the M1 Garand
How to Register
Applicants must register via the CMP Competition Tracker system website between November 21 and December 2, 2016. An electronic lottery will randomly assign the 20 available seats for each class date. CLICK HERE for more details.
Share the post "Build Your Own Garand at CMP Advanced Maintenance Class"
October 24th, 2016
Here’s some good news for owners of 1903 Springfields, 1903A3s, M1 Garands, and M1 Carbines. The CMP sells brand new chrome-moly barrels for these rifles for $190.00 or less. These authentic-profile barrels are made by Criterion Barrels in Richfield, WI, using the button-rifling process. They are “semi-finished” meaning they come chambered and headspaced within .010″ of finished size, with final fitting to be done by a competent gunsmith. The barrels are also externally Parkerized to match the finish of your vintage ’03, Garand, or M1 Carbine. To order, go to the CMP eStore and click the Barrels Link in the upper left.
New Criterion 1903 RIFLE Barrel, 4140 Chrome Moly Steel
Item: 065CRI/03 | $189.95
New 1903 barrels by Criterion Barrels, Inc., 4140 chrome moly steel, button rifled, contoured, and finish lapped after contouring. Comply with CMP competition rules and are legal for the 1903 Matches. Parkerized like the original 1903 and chambered .010 away from finish size to be fitted and headspaced when assembled to fit your receiver and bolt dimensions.
New Criterion 1903A3 RIFLE Barrel, 4140 Chrome Moly Steel
Item: 065CRI/A3 | Price: $189.95
New 1903A3 barrels by Criterion Barrels, Inc., 4140 chrome moly steel, button rifled, contoured, and finish lapped after contouring. Comply with CMP competition rules and are legal for the 1903A3 Matches. Parkerized like the original 1903A3 and chambered .010 away from finish size to be fitted and headspaced when assembled to fit your receiver and bolt dimensions.
New Criterion Garand (.30-06) RIFLE Barrel, 4140 Chrome Moly Steel
Item: 065CRI/M1 | Price $179.95
New .30-06 Garand barrels by Criterion Barrels, Inc. 4140 chrome moly steel, button rifled, contoured, and finish lapped after contouring. Comply with CMP Competition Rule 7.2.4 (6) and are legal for the Garand Matches. Parkerized like the original M1 and chambered .010 away from finish size to be fitted and headspaced when assembled to fit your receiver and bolt dimensions. Barrel is .30-06.
New Criterion Garand (.308) RIFLE Barrel, 4140 Chrome Moly Steel
Item: 065CRI/308 | Price $189.95
New .308 Win Garand barrels by Criterion Barrels, 4140 chrome moly steel, button rifled, contoured, and finish lapped after contouring. Parkerized finish and chambered .010 away from finish size to be fitted and headspaced when assembled to fit your receiver and bolt dimensions. NOTE: Barrel is chambered for .308 Winchester.
New Criterion Carbine RIFLE Barrel, 4140 Chrome Moly Steel
Item: 065CRI/CARBINE | Price $189.95
New Carbine barrels by Criterion Barrels, 4140 chrome moly Steel, button rifled, contoured, and finish lapped after contouring. Comply with CMP Competition Rules and are legal for the CMP M1 Carbine Matches. Parkerized like the original M1 Carbine and chambered .010 away from finish size to be fitted and head-spaced when assembled to fit your receiver and bolt dimensions. Barrel is .30 Carbine.
NOTE: For all barrel types, assembly and headspacing by a qualified gunsmith is required.
Credit Forum Member Boyd Allen for finding this CMP Barrel Special
Share the post "Chambered Criterion Barrels for ’03s and Garands: $180 – $190"
June 9th, 2016
Take a look at that unusual target below. We bet you’ve never seen one of these before. It’s a 50-Yard Sighting Target for the M1 Garand. It’s designed to allow a rifleman to confirm his zeros for multiple yardages all the way out to 1000 yards. But importantly, he can establish those zeros at a very “short” shooting facility, since the target is positioned at a mere 50 yards.
Here’s how it works. The target is placed at fifty (50) yards. You start at the bottom, aiming at the black circle. Then check your come-up table and work your way up, clicking step-by-step to the various horizontal lines set for 200, 300, 500, 600 and 1000 yards. This is NOT “spray and pray” — you need to have a pretty good idea of the clicks you need, based on your ammo’s ballistics. This target is calibrated for the U.S. Military M72 Ball Ammo. The targets are available from Champion’s Choice ($0.75 each) or from Creedmoor Sports (12 for $5.95).
Lapua’s Kevin Thomas used this target to get zeroed for the recent D-Day Anniversary Match at the Talladega Marksmanship Park. Kevin used the target for both his M1 Garand as well as his M1903A1 Springfield, both chambered for the .30-06 Springfield cartridge.
Zeroing at a Short Distance — How to Use the 50-Yard Sighting Target, by Kevin Thomas
As part of my preparation for the Garand Match at the CMP’s Talladega Marksmanship Park, I needed to zero my new M1 Garand, but I was crunched for time. I didn’t have time to get to my normal range and confirm zeros at actual yardages. But a 50-yard zero target came to the rescue. Made for M1s using the M72 National Match ammo, the target allows the shooter to establish fairly good zeros at 200, 300, 500, 600 and 1,000 yards if you’ve got access to a 50-yard range.
I have no idea when these 50-yard Sighting Targets were first developed, but they’ve been around for at least as long as I’ve been involved in this game (longer than I care to admit). It consists of a tall target, with a smallish black bullseye located at the bottom center. The bullseye is an aiming point only. Extending through the top of the target is a vertical line that runs directly up the center, to nearly the top of the paper. Across this, there are intersecting horizontal lines that are marked 200, 300, 500, 600 and 1,000.
The target was designed for the M1 rifle using then-issued M72 National Match ammunition. This ammo launched a 173gr FMJBT bullet at approximately 2,640 fps. It was a good load in its day, supersonic out to the 1,000-yard line. While that ammo is fairly scarce these days, this isn’t a problem for the handloader. My standard match load for the M1 Garand utilizes the 175gr Lapua Scenar HPBT, and delivers remarkably similar ballistic performance. Thus my normal Garand load translates nicely to this 50-yard target. Yes, this is by design. No point in reinventing the wheel when Lake City has already established what works!
In use, the shooter sets the target up at a measured 50 yards, and (this is critical) checks the vertical line with a plumb bob or a carpenter’s level, to ensure that it is absolutely vertical. Once the target is set, the rifle is fired and the group noted. From there, it is a simple matter of zeroing it normally to bring the groups into alignment with the vertical line, at the elevation needed for a particular range. Once your group is hammering the intersection of the vertical line and the horizontal line marked “200”, you have established your 200-yard zero for that rifle. Record the number of clicks, and you’re good to go. Raise the impacts up to coincide with the line marked “300” and you now have a 300-yard zero as well. And so on, right up the target. Record those settings in your data book, and you’re ready to go to the range at the full distances. If done carefully, you may be in the X-Ring, but at the very least, you’ll be well-centered and ready to get some hard dope recorded for future shoots.
The same target can also be used with an M14/M1A, at least at the shorter distances. The ballistics of the M118 and the current M118LR are similar enough that this will get you on target at the full distances, probably requiring just a half MOA or so change from the 50 yard zero you recorded. Same bullets, moving at a slightly more sedate 2,550 fps, you’ll be in the ballpark at least.
Bryan Litz has recently popularized the short-range zeroing methods once again, reintroducing it to a new generation of shooters that may not have been aware of the old M72 short-range zero target. The same principles apply, and with the advent of the myriad computer ballistics programs and chronographs on the market today, any shooter can rapidly develop his own zero targets to accomplish the same result. But in the meantime, especially with the M1’s resurgent popularity, it’s nice to know that there’s an easy way to do things without a trip to a full-length range. The modestly-priced 50-Yard Sighting Targets can be ordered through Champion’s Choice or Creedmoor Sports.
Oh, and when I arrived in Talladega, yes, my zeros were good! All’s well that ends well. Safe Shooting! — Kevin Thomas
Share the post "Using a 50-Yard Sighting Target with Vintage Military Rifles"
March 21st, 2016
Here’s something you’ve probably never seen before — an edible M1 Garand. You heard that right. The rifle you see in these photos is actually a specialty cake, and every element of the chocolate Garand is deliciously edible, even the authentic receiver and sights. Note the remarkable detail — the grain in the wood, the sling swivels, trigger guard, and buttplate. This is truely a masterpiece of cake-making.
This is my rifle. There are many like it, but this one is edible (and delicious).
My edible rifle is my best friend. It is my life. I must master it as I must master my life.
Without me, my edible rifle is useless. Without my edible rifle, I am useless. I must eat my rifle true….
This impressive example of cake-making was created by Kentucky Wildflour Cakes. This was created as a “Groom’s cake” for a wedding reception. Below is a photo of the unique chocolate cake in the making. The fellow who commissioned this work of culinary art posted: “I begged you to knock this one out of the park for me, and by gosh you blew it out of the park! This was the main attraction at our reception last night and people are still going on and on about it. I can’t even begin to express how thankful I am for your work!”. For those doubting Thomases who can’t believe this masterpiece was actually created, layer by layer, as a cake, here is a photo of the M1 Garand cake “under construction”:
Share the post "The Chocolate Garand — Edible M1 Garand Cake"
December 4th, 2015
What really happens when an M1 Garand fires the final round and the En-Bloc clip ejects with the distinctive “Ping”. Well thanks to the folks at ForgottenWeapons.com, you can see for yourself in super-slow-motion. The entire cycling process of a Garand has been captured using a high-speed camera running at 2000 frames per second (about sixty times normal rate). In this video, watch the clip eject at the 00:27 time-mark. It makes an acrobatic exit, spinning 90° counter-clockwise and then tumbling end over end. At the 1:20 time-mark you can actually see the two sides of the clip oscillating back and forth as the clip flies through the air.
2000 frame per second video shows M1 Garand ejecting spent cartridges and En-bloc clip.
Share the post "Cool Slow-Motion Video of M1 Garand"
November 11th, 2015
On this Veterans Day, we thought we would reprise this inspirational profile of SGT Robert Evans, a U.S. Army veteran who lost his right hand in combat in Iraq. Remarkably, despite his injury, SGT Evans obtained the Distinguished Rifleman Badge. Read on to learn more about this remarkable young soldier.
Wounded Warrior Goes Distinguished
Report based on story by Ashley Brugnone, CMP writer
At the 2013 Western CMP Games, SGT Robert Evans attained what many shooters seek their entire shooting careers — a Distinguished Rifleman’s Badge. Evans earned his DR badge with just one hand, after losing his right hand while serving in Iraq with the U.S. Army.
 SGT Robert Evans: Defying the Odds, Single-Handedly
AFter joining the Army in 2003, SGT Robert Evans served two tours in Iraq, suffering a spinal injury on the first tour. On his second tour, his life changed forever. On May 31, 2007, Evans was commanding a Bradley Fighting Vehicle in Iraq. As the Bradley drove under an old Fedayeen guard shack, an IED on top of the guard shack detonated while Evans was reaching out of the turret. The blast amputated Robert’s right hand at the wrist.
Even as a young boy, Evans had always enjoyed shooting. He vowed to stay involved with the sport despite his injury: “I couldn’t give up shooting after I lost my hand. It’s always been too important to me,” he said. “No matter what is going on in my life, when the sights are aligned and the hammer is about to fall, nothing in the world matters at that second. It’s my nirvana.”
Evans worked his way back into the sport by starting in F-Class. The position allowed him to hold hard and pull the trigger, while also being able to use his optics. Then he got involved with J.J. O’Shea’s M1 for VETS Project. The project helps transition wounded combat veterans back into the world of shooting, with equipment arrangements, position training and mental preparations.
Working with the M1 for Vets group, Evans started shooting again. But there were challenges: “The first time I shot after my amputation, it was very frustrating,” he said. “I couldn’t hold still, and shooting left-handed was so foreign.” Being extremely right-eye dominant his entire life, the loss of his right hand caused him to relearn many things, including how to shoot. Learning how to reload and adjust for wind while slung up became a pain for Evans….
In 2008, after several months and rigorous hours of dry firing, Evans found himself crossing the threshold of Camp Perry — a dream he had waited to fulfill his entire life. He scored around 50 points standing, out of 100, on his first trip. Though not bad for someone with an amputation, that wasn’t enough for Evans. He wanted to become a Distinguished Rifleman.
SGT Evans during Team Match at 2013 CMP Western Games.
He began to realize his dream as he earned his first 10 points (towards Distinguished) at Camp Perry in 2012. It took him 15 months to LEG out. His next 6 points came at the 2013 Eastern Games in Camp Butner, NC, followed by 10 more points at the 2013 National Matches. There, hoping to “bronze out,” he managed to one-up himself to actually earn a silver medal.
Then came the 2013 Western Games at the Ben Avery Shooting Facility in Phoenix, AZ. Never giving up hope and remembering his long journey from the hospital bed to the firing line, he received his final 8 points. SGT Robert Evans had become a Distinguished Rifleman.
“There was a lot of pressure, speculation and competition as to who would be the first Combat Wounded Veteran to ‘Go Distinguished’ within M1 for VETS,” he said. “I’m very proud to have earned my badge, but more importantly, I hope that more wounded veterans will realize that it is within their grasp. It’s not an impossibility anymore. I hope it motivates everybody to train a little harder and hold a bit tighter – not just wounded veterans. If I can do it, anybody can.”
Posted Courtesy of the Civilian Marksmanship Program, www.TheCMP.org
Author: Ashley Brugnone, CMP Writer/Editor
Share the post "Wounded Warrior Earns Distinguished Rifleman’s Badge"
August 6th, 2015
Victor Betzold had a Camp Perry experience for the ages. At the 2015 CMP Games, Betzold won the Garand Match, won the M1 Carbine Match (setting a new Record), and took the 3-Gun Aggregate for the second year in a row. Now that’s an impressive performance. Betzhold is no stranger to shooting – beginning in junior high and firing well into college, then taking his love for guns into the Army. After the years went on and work and family became higher priorities, he fell away from the sport he loved. But now that he’s retired at age 60, he’s had time to practice again – practice that has certainly paid off.
During his remarkable showing at the National Games Matches, Betzold won the Carbine Match with a score of 375-6X, setting a new National Record in the process. In the National Garand Match, Betzold fired a score of 290-7X to become the overall winner of a field of 1213 competitors.
“It feels great,” he said. “I’ve been working at this for a long time.” The 60-year-old Betzold was also the top senior for both the Garand Match and the Carbine Match.
With his outstanding performances in the Garand and Springfield Matches, as well as an exceptional seventh-place finish in the Vintage Military Match, Betzold claimed the 3-Gun Aggregate title for the second year in a row — with a combined score of 865-19X.
Lady Competitor at the Garand Match (file photo).
To review complete results for all CMP National Match events at Camp Perry, visit the CMP 2015 Trophy Matches and SAFS Results Page.
Share the post "Old Guys Rule! 60-y/o Betzold Wins Garand and Carbine Matches"
November 19th, 2014
Here’s a shocking video showing a massive Kaboom (KB) that literally destroyed an M1 Garand in the hands of a lady shooter. One second she has a classic .30-06 battle rifle in her arms, and the next second she has nothing but a pile of parts. She is fortunate to have survived this incident without apparent serious injury. She may have had a squib (undercharged round) in her prior shot at the 00:12 time-mark. At 00:15 it seems she may have experienced “click no bang” (we can’t tell for sure). The detonation occurs at time-mark 00:25, and is then replayed in slow-motion.
 If this Kaboom wasn’t caused by a squib, there might have been a catastrophic failure of the cartridge that failed to fire at 00:15. The shooter herself, posting as ArizonaGirl24 on YouTube, thinks the gun may have fired out of battery. What do you think?
Text accompanying the posting of this video on LiveLeak, states: “A woman, her shooting partner, and their cameraperson are lucky to be alive. Her M1 Garand detonated after she failed to check the barrel for an obstruction due to an apparent squib round….
[After the shot at 00:12] she is obviously aware that something is amiss and seems to check the chamber, but does not unload the rifle to check for the presence of a barrel obstruction.
She raises the rifle and fires it again, causing a catastrophic weapon failure. Parts of the weapon fly in all directions. The video then terminates.”
What happened to the shooter? She reported: “I was very lucky with the outcome. I have lots of splinters and bruising, but nothing broken. My left hand took the brunt of the blow to my wrist and palm of my hand. Still pretty painful, but I will be fine.”
LESSON ONE: If you experience any kind of malfunction, or what appears to be a light-recoiling (or soft-sounding) shot, you should STOP shooting immediately. Clear the firearm and check for barrel obstructions.
LESSON TWO: Always wear ear and eye protection when shooting any firearm, even rimfires.
LESSON THREE: With a semi-auto gun, ensure the bolt is completely in battery after every shot.
LESSON FOUR: When hand-loading check EVERY round for powder charges prior to seating bullets, and weigh your loaded rounds before boxing them. Also check for high primers on EVERY round. If using a progressive press, use a Lock-Out Die that will alert you to any under-loaded cartridge. Be wary of commercial reloads.
Video tip from Mark LaFevers. We welcome reader submissions.
Share the post "Shocking Video: M1 Garand Explodes in Woman’s Hands (Squib?)"
October 3rd, 2014
 Classic American battle rifles have regained popularity via M1 Garand matches, service rifle matches, the M1A Match at Camp Perry, and Vintage Sniper competitions. If you own a classic M1 Garand, or an M1A, the modern semi-auto descendant of the M14, you should enjoy the two videos presented here. With help from our friend Grant G., we managed to located two original U.S. Army training films, one for the M1 Garand, and one for the M14. Both films use clever animated drawings to show the gas guns’ internal operations and cycling processes.
M1 Garand Training Film
Here is a U.S. Army training film for the M1 Garand (officially the United States Rifle, Caliber .30, M1). The M1 Garand was the first semi-automatic battle rifle to be generally issued to the infantry of a major nation, though other countries issued semi-auto rifles to special units. Gen. George S. Patton called the Garand “The greatest battle implement ever devised.”
Animated Diagrams Show M1 Garand Operational Cycle starting at 2:00-Minute Mark:
M14 Training Film
The successor to the M1 Garand was the M14. The 27-minute official U.S. Army video below demonstrates the operation of the M14. Field-stripping is shown from the 5:13 time-mark through 8:30. Cut-away drawings show the M14’s gas operation at 8:40.
The complete 8-step functioning cycle is demonstrated from the 9:25 time-mark through 22:41. These eight operations are: 1) Feeding; 2) Chambering; 3) Locking; 4) Firing; 5) Unlocking; 6) Extracting; 7) Ejecting; and 8) Cocking. This movie is fairly long, but fans of battle rifles will find it well worth their time. Every M1A owner should definitely watch this video start to finish.
Watch M14 Functioning Cycle Starting at 9:25 Mark:
Share the post "Blast from the Past: M1 Garand and M14 Training Films"
|
