|
|
January 6th, 2015
What can happen when the bottom-most primer in a primer feed tube goes off? A big bang, that’s what. Some or all of the primers in the vertical feeding tube can go off in a chain detonation. That’s exactly what happened to Dustin Ellermann, Top Shot Season 3 Champion. Scary experience, but thankfully Dustin was not injured. He writes: “Super thankful that I was wearing my Wiley X eye protection this weekend when I was reloading some .223 rounds. My press detonated nearly 100 small rifle primers. Shown here is the magazine feed tube. Not fun but it could have been much worse. Stay safe!”
When working with progressive reloading presses, you should definitely wear eye protection. Dustin’s chain detonation experience proves that — without a doubt. Remember you only have one set of eyes!
APS Strips — Alternative to Primer Tubes
 When you stack a column of primers in a single metal tube, you’re asking for trouble. As Dustin Ellermann learned, when one primer fires, the entire column can follow suit in a chain detonation. Thankfully, you do have options when it comes to primer feeding on a progressive press. RCBS developed an innovative primer system for its Pro-2000 progressive press. Instead of being stored in a vertical tube, primers are placed in flat, plastic “APS” strips, with a ring of plastic separating each primer. Moving horizontally, primers are never stacked, so the chance of a chain detonation is reduced dramatically. The re-usable APS strips are color-coded for different primer types. You can buy CCI “pre-loaded” primer strips, or you can insert any brand of primers into strips using an RCBS strip-loader tool.
RCBS Pro-2000 with APS Strip Priming System
AccurateShooter.com Editor Uses Strip Primers
This Editor owns an RCBS Pro-2000 progressive press (manual-indexing version). The RCBS strip-priming system was one key reason I selected the RCBS Pro-2000 over similar-priced progressives from Dillon and Hornady. I believe the strip primer system is safer, more positive, and easier to use. Before I purchased my RCBS progressive, I “road-tested” the competition. I loaded hundreds of rounds on each of four different progressives: Dillon 550B, Dillon 650, Hornady Lock-N-Load, and RCBS 2000. I was concerned about the primer feed tubes on the Dillons, and I found the RCBS rotary powder measure was much more precise (and easier to adjust) than the sliding bar system on the Dillon machines. The RCBS priming system was definitely more fool-proof than the system on the Hornady press (a first-generation L-N-L that had issues with primer feeding). After “test-driving” blue, red, and green brand progressives extensively, I settled on the RCBS Pro-2000. A decade later, I still think I made the right choice. I like the APS strips for big jobs, and I can also use them in the RCBS hand-priming tool (shown below). With the strips, its easy to prime 20 or 40 cases at a time, and then switch to another type of primer for comparison testing.
December 19th, 2014
The RCBS Rock Chucker is a rugged, classic design that can last a lifetime. If you are looking to get started with hand-loading, or just need another press for your reloading room, the Rock Chucker is a great choice. And now it’s easier than ever to purchase a Rock Chucker. Right now, Bullets.com has slashed the price on its RCBS Rock Chucker Supreme presses. As part of an inventory reduction sale, Bullets.com is now offering the RCBS Rock Chucker Supreme (with full RCBS warranty) for just $99.95. Act soon — this offer is limited to supplies on hand.
More Savings — $10.00 Rebate from RCBS
Getting a great press for under one hundred bucks is hard to beat. But get this — RCBS is currently offering a $10.00 rebate with any qualifying RCBS product purchase of $50.00 or more made before December 31, 2014. So… if you buy this press before the end of 2014, you can get a $10.00 RCBS rebate. That lowers your effective cost to $89.95 for the Rock Chucker Supreme. That is one amazing deal. CLICK HERE for REBATE INFO.
December 5th, 2014
 Here’s a clever, easy modification for your RCBS ChargeMaster electronic powder dispenser. Many folks use a McDonald’s straw to smooth kernel flow out of the dispensing tube. Forum member Mike S. (aka in2deep) found that, even with a straw in place, he sometimes got clumps, which dropped 5-6 kernels at once, throwing off his dispensed weight.
Mike looked at the situation and ingeniously decided to trim the straw into little v-shaped arms or prongs. This helps to break up the clumps, so the kernels flow out the end of the tube more consistently during the dispense cycle. Mike writes:
Soda Straw Modification
This is a further tweak of the popular soda straw modification as the original mod would still allow Varget powder to collect in the straw and dump sometimes as many as 6 or 8 or even more extra kernels in the pan. It would sometimes signal an overcharge, but even when it didn’t there could be as many as 6+ kernels too high or too low (total spread of 12+).
The little arms (prongs) on the straw tend to separate the kernels into groups of 1 or 2 or 3 and prevents piling and many times the throw is now within 1 or 2 kernels of the desired weight.
Straw Cutting Tips — Mike found the shape/angle of the “arms” is very important. If the cuts are too fine or too course it allows the kernels to collect almost like before but the illustrated angle seems to allow an average of only 2 or 3 kernels per trickle input from the machine. This means that more charges are much closer to the actual desired weight and max kernel variances will be cut in less than half and there will be almost no overthrows.
Credit Boyd Allen for sourcing this tip.
October 17th, 2014
Natchez Shooters Supplies just announced a major 3-Day SALE on big name reloading gear. Prices on high-quality RCBS, Redding, Hornady, Lyman, and MEC products have been slashed. But this sale runs for three days only — the deals expire 10/19/2014. (NOTE: we are not sure if this means end of day 10/19 or if the deals expire at 11:59 pm on 10/18 — be forewarned).
If you are in need of a reloading press, electronic powder dispenser, or a vibratory tumbler, this is a great opportunity to save some serious coin. For example, the RCBS Chargemaster, which sells elsewhere for $340.00 – $375.00, is just $289.99. That price is way lower than we could find elsewhere. CLICK HERE for Natchez SALE
CLICK graphic below to see larger version with more products:
Sale tip by EdLongrange. We welcome reader submissions.
August 30th, 2014
 The February 2013 edition of Shooting Sports USA magazine has an interesting feature by Glen Zediker. In this Transporting Success, Part I article, Zediker explains the advantages of loading at the range when your are developing new loads or tuning existing loads. Glen, the author of the popular Handloading for Competition book, discusses the gear you’ll need to bring and he explains his load development procedure. In discussing reloading at the range, Glen focuses on throwing powder and seating bullets, because he normally brings enough sized-and-primed brass to the range with him, so he doesn’t need to de-prime, re-size, and then re-prime his cases.
Zediker writes: “Testing at the range provides the opportunity to be thorough and flexible. You also have the opportunity to do more testing under more similar conditions and, therefore, get results that are more telling. Once you are there, you can stay there until you get the results you want. No more waiting until next time.”
Zediker starts with three-shot groups: “I usually load and fire three samples [with] a new combination. I’ll then increase propellant charge… based on the results of those three rounds, and try three more. I know that three rounds is hardly a test, but if it looks bad on that few, it’s not going to get any better.”
Glen reminds readers to record their data: “Probably the most important piece of equipment is your notebook! No kidding. Write it down. Write it all down.”
 There’s More to the Story…
Editor’s Note: In Zediker’s discussion of loading at the range, he only talks about throwing powder and seating bullets. In fact, Glen opines that: “there is little or no need for sizing.” Well, maybe. Presumably, for each subsequent load series, Zediker uses fresh brass that he has previously sized and primed. Thus he doesn’t need to de-prime or resize anything.
That’s one way to develop loads, but it may be more efficient to de-prime, re-size, and load the same cases. That way you don’t need to bring 50, 80, or even 100 primed-and-sized cases to the range. If you plan to reload your fired cases, you’ll need a system for de-priming (and re-priming) the brass, and either neck-sizing or full-length sizing (as you prefer). An arbor press can handle neck-sizing. But if you plan to do full-length sizing, you’ll need to bring a press that can handle case-sizing chores. Such a press need not be large or heavy. Many benchresters use the small but sturdy RCBS Partner Press, an “O-Design” that costs about $79.00. You may even get by with the more basic Lee Precision Compact Reloading Press, shown in Zediker’s article. This little Lee press, Lee product #90045, retails for under $30.00.
July 22nd, 2014
Bullets.com has launched a huge closeout on its entire RCBS inventory. Here’s a great opportunity to save big bucks on high-quality RCBS tools and reloading accessories, including RCBS Chargemasters and even RCBS Rockchucker presses. The folks at Bullets.com report: “We have slashed prices to levels at or below cost on hundreds of items.” Guys — take note: this is a unique opportunity to pick up some great gear at truly rock-bottom prices. In fact the deals are so good that your Editor plans to purchase a couple presses, a powder measure stand, and some accessories for my RCBS 2000 progressive press. I really don’t think you can beat these prices… and remember this is an inventory close-out sale, limited to stock on hand. When it’s gone, it’s gone. So don’t say we didn’t warn you!
GO to RCBS Sale at Bullets.com
Closeout items include:
 Reloading Presses
Electronic Powder Measures
Reloading Kits
Digital and Beam Scales
Tumblers
Ultrasonic Cleaners
Sizing and Seating Dies
Shell Holders
Bullet Casting Kits
Case Prep Tools and much more.
Here Are Some of the RCBS Presses on Sale:
Get RCBS Factory Rebates
In connection with this Bullets.com SALE, you can save even more with RCBS factory rebates. If you spend $50.00 you can get a $10.00 rebate. If you spend at least $300.00 on RCBS products you can save $50.00. These rebates are good through 12/31/2014. CLICK HERE for details.
Click for Detals
May 27th, 2014
|
New handloaders often ask us for advice on reloading techniques and equipment selection. It’s always best for novice reloaders to work under the guidance of an experienced mentor. Nothing beats “learning the ropes” with an experienced reloader at ones side. In addition, new handloaders should acquire one or more good reloading manuals, such as the Hornady Reloading Handbook (9th Ed.). We recommend reading the introductory chapters of a reloading manual to get a good understanding of the basic principles involved.
Along with print manuals, instructional DVDs are available. RCBS sells a 32-minute, step-by-step Precisioneered Handloading DVD, narrated by Shooting USA’s Jim Scoutten. This $9.19 DVD covers the basics of metallic cartridge reloading and shotshell reloading.
|
|
For those who have already mastered the basics, Redding offers a 45-minute instructional DVD, appropriately named Advanced Handloading: Beyond The Basics ($17.52 at Amazon.com). The Redding DVD, produced with help from Sierra Bullets, is narrated by John Barsness, field editor of Rifle and Handloader magazines. The Redding DVD does go “Beyond the Basics” but it really is more an intermediate resource — it doesn’t reveal some of the most sophisticated methods of case prep and load tuning used by competitive benchrest shooters. Nonetheless it is a good resource for those getting started with rifle cartridge reloading.
January 4th, 2014
RCBS is offering $10 or $50 rebates on reloading products purchased in the first half of 2014. Here’s the deal: from January 1, 2014 through June 30, 2014, reloaders who purchase $50 of RCBS tools and accessories can receive a $10 rebate, or those who buy $300 in RCBS products can get $50. To qualify, 2014 purchase(s) must be made before June 30th, and the rebate application must be submitted by July 31, 2014. Be sure to save your original receipts and UPCs from the product packaging: “Consumer submits rebate coupon, box UPCs and original cash register receipt and/or dated itemized sales invoice. Photocopies will not be accepted.” CLICK HERE for rebate form and further information.
Rebate tip from EdLongrange. We welcome reader submissions.
September 20th, 2013
 Using ultrasound in a liquid solution, you can clean your cartridge brass inside and out. Ultrasonic cleaning is nothing new — we described this process years ago. But with the increased cost of brass, more and more shooters are turning to this effective process to get their cases clean.
Now RCBS offers an affordable Ultrasonic Cleaning Machine with some great features. The new RCBS machine boasts a 3-liter capacty, user-friendly keypad, and a built-in 100-watt heater with four settings. The unit also includes a handy drain valve and drain tube.
Ultrasonic cleaning works fast, without the long processing time (and dust) of conventional tumbling. Cleaning cases with ultrasonic machines has become very popular, as the ultrasonic process reliably removes caked-on carbon and grime from brass cases inside and out, even in the primer pocket. We do recommend that, after ultrasonic cleaning, you consider using a dry neck lube to restore lubricity to your necks for the first and second firings.
The new RCBS ultrasonic cleaner features a large 3-liter capacity, 60 watt transducer, and 100 watt ceramic heater. ‘Street Price’ for the RCBS ultrasonic machine is under $150.00, and this unit qualifies for RCBS Rebates ($10 off $50 purchase or $50 off $300.00 purchase). RCBS also sells 32 oz. bottles of cleaning concentrate that will make up to 10 gallons of Ultrasonic Solution.
August 6th, 2013
 ATK (Alliant Techsystems Inc.), already a giant conglomerate, may soon get even bigger. Reuters reports that ATK “is in advanced talks to buy Bushnell Outdoor Products Inc. in a deal that could value the gun accessory maker at around $1 billion[.]” In addition to scopes, Bushnell makes rangefinders, binoculars, GPS units. Bushnell sells a myriad of other products for outdoorsmen through its brands Butler Creek, Hoppe’s, Millett, Night Optics, Primos, Simmons, Stoney Point, Tasco and Uncle Mike’s.
According to Reuter’s sources, ATK is engaged in high-level negotiations with MidOcean Partners, a holding company that currently controls Bushnell. Reuters cautioned that “a deal has not yet been finalized and negotiations could still fall apart”.
If the Bushnell deal goes through, this will be the second major acquisition for ATK in the past few months. In May 2013, ATK paid $315 million for Caliber Company, the parent company of Savage Sports Corporation which runs Savage Arms and Stevens. Savage is being integrated into ATK’s Sporting Group business which includes Federal Premium, Alliant Powder, CCI, RCBS, Speer, Weaver Optics, Champion Targets, and other outdoor sports brands.
ATK is also a major defense contractor, producing ammunition, weapons systems, aerospace products and much more. Currently valued at $3.1 Billion, ATK has been a top performer on Wall Street recently. ATK shares have more than doubled in the past 12 months, outpacing most stocks, even in a rapidly rising overall market. ATK shares were trading at $97.53 today, compared to $47.24 one year ago.
Bushnell was founded in 1948. The company makes scopes, binoculars, GPS units, laser rangefinders, GameCams, eyewear, and other outdoor gear. Bushnell is the parent of many other outdoor product brands, including: Bollé, Butler Creek, Final Approach, Hoppe’s, Millett, Night Optics, Primos, Serengeti, Simmons, Stoney Point, Tasco, and Uncle Mike’s. Last year the Bushnell group of companies had $100 million in earnings before taxes, interest, and depreciation.
|
