What are the hottest-selling firearms in the “previously-owned” marketplace? As you might expect, the Remington Model 700 tops the list as the best-selling used bolt action rifle. The leading semi-auto rifle is the little Ruger 10/22 rimfire, followed by another Ruger, the Mini-14. Despite the high cost ($2K+ for the best examples) the Colt Python is the best selling used revolver. (People have realized that Pythons have proven to be good investments.)
These rankings were recently released by GunBroker.com. Every month, GunBroker.com publishes the Top 5 Best Sellers List for each major category of firearms sold on the popular gun auction site.
Share the post "Most Popular Used Firearms Ranked by Gunbroker.com"
Remington has just introduced an all-new series of “Ultimate Muzzleloaders” that promise to “raise the bar” for muzzle-loading performance. These rifles, based on Rem 700 actions, feature a new type of ignition system with a special breech plug and a primed, brass case. The magnum-primer-fitted ignition casing is pushed onto the breech plug by the bolt (see illustration below). This creates a tight gas seal for the magnum primer, allowing reliable ignition of up to 200 grains of powder. That translates to higher velocities and more energy.
Video Shows How New AMP Ignition System Works:
Remington reports: “The Ultimate Muzzleloader sets a new performance threshold with the use of a closed breech system that provides a cleaner and hotter ignition. The AMP (Accelerated Muzzleloader Performance) ignition system uses a uniquely-sized brass case with a Remington 9 ½ large magnum rifle primer that is push fed into the breech plug creating a gas seal in the flash hole of the primer (see cutaway below). The result allows the shooter to load up to 200 grains of powder for increased range, energy, and on-game performance.
Using 200 grains of Triple Seven® Pellets in combination with Barnes’ Spit-Fire T-EZTM 250-grain muzzleloader bullets, the Model 700 Ultimate Muzzleloader gives the shooter the ability to reach velocities over 2400 fps. [A 300gr bullet can travel 2200 fps with 3300 ft-lbs. of energy.]”
Remington claims its new system yields “centerfire-like performance and accuracy out of a muzzleloader” with “higher velocities, greater energy, and further effective range.” In addition, the primed casings are easier to handle in the field compared to small 209 shotshell primers. Spare primed cases can be stored in a compartment below the receiver (see below).
Two stocks are offered — a gray/brown laminated stock or a gray Bell & Carlson M40 fiberglass stock. Both versions come with a 26″ stainless barrel. On the laminated model the barrel is fitted with rifle sights front and rear. The Rem 700 muzzleloader features an adjustable X-Mark Pro trigger, factory-set at about 3.5 pounds pull weight.
M700 Ultimate Muzzleloader – Synthetic
26-inch SS Fluted Barrel
Bell & Carlson Medalist M40 Stock with Storage
X-Mark Pro® Adjustable Trigger, 2.5-5 Pounds
24 Primed Cases and 24 Projectiles
Ships in a Hard Case
MSRP – $1295
M700 Ultimate Muzzleloader – Laminate
26-inch SS Fluted Barrel with Rifle Sights
Laminate Stock with Primed Case Storage
X-Mark Pro® Adjustable Trigger, 2.5-5 Pounds
24 Primed Cases and 24 Projectiles
Ships in a Hard Case
MSRP – $1295
Share the post "New Remington 700 High-Velocity ‘Ultimate Muzzleloader’"
Tech Tip by Mark LaFevers
Our “master fabricator” Mark LaFevers has installed some of the CG Mod 22 triggers from X-Treme Shooting Products. This is an excellent Two-stage Trigger for the Remington 700 type actions. Though advertised as a “drop-in”, Mark found some stock fitting was required when installing this unit in a wood stock. Here is Mark’s brief report.
CG Mod 22 Trigger Installation Tips
Having already installed a CG X-Treme trigger in my Borden-action Eliseo tube gun, I was looking forward to the same easy installation and adjustment process on a friend’s Remington 22-250 in a laminate varminter stock. Where there were no fit issues in the aluminum Eliseo stock, I had to relieve a fair amount of wood at the tang end of the laminate stock inletting. While not difficult, this took a little more time than I had anticipated, using a 3/8″ square file.
The end result was just as satisfying, a two-stage trigger fully independently adjustable with outstanding feel and sensitivity. The adjustment instructions for the CG Mod 22 trigger from X-Treme Shooting Products are clear and easy to follow.
I like to set the length of travel of the first stage long enough to define pulling up to the end of it clearly, with the second stage set just heavy enough that you don’t pull into it accidentally before you are ready. The trigger breaks very cleanly, helping to make the shot either on paper or hunting. It’s nice to find a two-stage trigger with this kind of precise adjustment that also has a safety — an important feature for a hunting gun.
Share the post "Installing a CG Trigger in A Wood Stock"
Here at AccurateShooter.com we tend to focus on highly-accurate (1/2-MOA or better), custom-built bolt-action rifles. But for home defense, deer hunting, or just having fun with the grand-kids, factory-built firearms serve their purpose. With that in mind, we wondered, “Just what are the most popular mass-production firearms these days?” To get a complete answer you must consider both new AND “previously owned” sales figures. Gunbroker.com, the biggest firearms auction site, recently tallied the top-selling firearms in various categories. Below we present Gunbroker’s January 2014 “Best Sellers” among rifles and pistols.
Some things we expected — the Rem 700 is the top-ranking bolt-action rifle, and the Ruger 10/22 was the leading semi-auto rifle. But in the pistol rankings, there were some surprises. Despite being out of production, the Colt Python is the best-selling revolver. Why is an out-of-production gun a top-seller? First, high-grade Pythons are actually increasing in value, making this “snake” a good investment. Pythons are also highly accurate, beautifully-finished revolvers with superb triggers. These qualities make the guns highly desirable to serious shooters as well as collectors.
Are you thinking thinking about a low-budget Remington 700 project? Perhaps you want to build a basic hunting rifle for a young family member. Or maybe you want to re-stock or re-barrel an old Rem 700 that’s sitting in the safe. Well here’s your opportunity. CDNN Investments has attained a large inventory of brand new “Take-Out” factory parts from Remington rifles. You’ll find triggers for $49.99, barrels for $49.99/$69.99, and synthetic stocks for $49.99/$59.99. If you already have a Rem 700 action, this will let you assemble a complete rifle for very little money. These are new Remington-made parts. NOTE: Though chambered as indicated, gunsmithing is required for installation of these barrels.
For more information, or to order, visit CDNNinvestments.com or call (800) 588-9500.
Share the post "Hot Deal: Remington ‘Take-Out’ Stocks, Barrels, and Triggers"
Rem 700 Action Sale
Need an action for your next varmint, hunting, or tactical rifle project? How about a brand new, short action Remington 700 receiver for $389.99? Sound good? Then visit Brownells.com to take advantage of this special offer. These .308-size-bolt, blued-finish Rem 700 actions have been marked down from $449.99 to $389.99 — a $60.00 savings. (Brownells also has Rem 700 Long Actions priced at $499.99). You should act soon, as supplies are limited. FFL is required for purchase.
Factory-Original, Current Production Actions with X-Mark Pro Triggers
These receivers are from a current factory production run and meet the latest design specifications and quality control standards at the Remington factory. The $389.99 versions have a .308-Win diameter bolt face. Each is precision-machined from either carbon steel or stainless steel barstock for uniform strength, drilled and tapped for scope bases, and ready to accept your choice of barrel and bottom metal. Remington’s bolt assembly features two, up-front bolt lugs for tight lockup and reliable pressure retention, plus 2-panel checkering on the bolt handle. A rivetless, circlip-type extractor and spring-loaded plunger ejector provide positive case extraction. Each action is equipped with Remington’s new X-Mark Pro trigger for improved trigger pull and easy adjustment. The easy-to-reach, two-position thumb safety engages quietly, and allows unloading while in the “safe” position.
EDITOR’s NOTE: The following commentary by Brownells explains why the availability of new production Rem 700 actions is unpredictable, and why Rem 700 actions are a good choice for a rifle build.
Remington 700 Actions — Availability
It’s been many years since Brownells has been able to offer Remington 700 actions in its catalog. The problem has been unsteady supply: Remington Arms Co. will release actions to the commercial market only when it is sure it has enough supply to satisfy its own production needs for complete guns. Now, however, through a new arrangement with Remington, we are able to offer both Long and Short 700 actions (but supplies are limited).
Why The Rem 700 Action?
It’s simple. For 50 years, the Remington 700 has been the flagship of commercial rifle actions, providing proven reliability, fine accuracy, plus the largest selection of aftermarket bolt action parts in the industry. The Remington 700 action has proven itself for hunters and target shooters alike. The Rem 700 action still ranks as the number one choice of custom gun makers. Consequently, you will find a large selection of Rem-700 inletted stocks, along with aftermarket triggers, bottom metal, scope rails, and other accessories.
When They’re Gone…
There is, indeed, a limited number of commercial suppliers for these actions, and we are proud to be one of them. Although steadier now, the supply is still not certain enough that we’re ready to catalog them in our Big Book. We can only offer what we have in stock — and simply cannot guarantee permanent availability in the future. If they sell out, we all may be back to scrounging the gun shows and searching the Internet for a lucky deal on something used, or pirating the action from a brand new gun.
Share the post "Factory-New Remington 700 Short Actions for $389.99"
Remington will introduce a new bolt-action rifle at SHOT Show, the Model 783. Remington positions the new model 783 as a mid-level offering between the Model 770 and Model 700 SPS, according to John Fink, Freedom Group Rifle Product Manager. This new rifle was first revealed in an American Rifleman article by Richard Mann, who tested an early production version in September 2012. Mann reports: “The ‘7’ in the model designation comes from the 700 line of rifles, the ‘8’ is kind of a throwback to the affordable but reliable model 788, which was discontinued 20 years ago, and the ‘3’ is for the three in 2013. The suggested retail price is $451, but you can expect street prices to be closer to $400.”
Remington is claiming sub-MOA accuracy for the Model 783, as demonstrated by the “teaser” photo sent out to Remington customers earlier this week:
Adjustable Trigger with Insert
The rifle features a polymer stock, cylindrical action, and an adjustable trigger with a control insert (as used on the Savage AccuTrigger and Marlin Pro-Fire trigger). Remington’s “CrossFire Trigger System” is pre-set at 3.5 lbs pull weight. According to the reviewer, Remington’s CrossFire Trigger is “similar in appearance to the Savage AccuTrigger and the Marlin Pro-Fire Trigger; it has a center lever that locks the trigger until it is fully depressed.” (We think selecting “CrossFire” as a product title was a dumb move by Rem’s marketing guys.)
Model 783 Has Barrel Nut System
Remington has borrowed a trick from Savage, employing a barrel nut system for fitting barrels to model 783 actions. The model 783’s two-lug bolt features a Sako-style sliding-plate extractor — this is a departure from the system on a Rem 700. Scopes can be mounted with two Model 700-spec front scope bases. However, Remington plans to offer integral scope mounts in the near future.
Designed for game hunters, the model 783 will initially be offered in four chamberings: .308 Winchester (short action), .270 Winchester, .30-06 Springfield, and 7mm Rem. Magnum. Remington says it will roll out more chamberings by the middle of 2013. In addition a compact-stock version with a shorter length of pull will be offered. Barrels are 22″ or 24″ with a “magnum contour”. Model 783 rifles will be produced in the Freedom Group’s Mayfield, Kentucky manufacturing plant.
Share the post "Remington Introduces Affordable Model 783 Bolt Gun"
There was a lot of buzz at the Defiance Machine booth at SHOT Show. The new Defiance actions are beautifully made, and they have already been used in some impressive custom rifle builds. Defiance, based in Columbia Falls, MT, has rolled out a line-up of four (4) custom actions: Rebel, Mutant (for tubeguns), Renegade (for .408 CheyTac), and Titan (for 50 BMG). These actions all feature beautiful machining, with Wire EDM-cut lug ways, advanced-design extractors, and a true one-piece bolt. All action materials are pre-hardened before machining to prevent changing tolerances during heat-treating. Southpaws will be happy that both right and left-hand versions of all four actions are offered.
The Rebel actions feature a Remington 700 footprint for ease of inletting and stock compatibility. Notably, the Rebel actions are available in four lengths. Buyers can choose Medium, X-Medium, Long, or X-Long lengths to accommodate all popular factory chamberings and extended-length handloads. Multiple magazine well cuts are available for all of today’s popular magazine types including hinged floorplates, DBMs, or single-shot. For a rock-solid optics installation, Defiance can supply Mil-spec Picatinny rails with various built-in MOA geometry. This stout rail is secured to the action with five pins and 1/4-28 X 1/2″ screws. Base price on a Rebel is $1270.00 (Medium) or $1300.00 (Long), with many available extra-cost options. Defiance says delivery will take at least 60 days from order date.
We were very intrigued by the Mutant action with its integrated recoil lug. Offered in Medium and Long action lengths, Defiance’s new Mutant receiver is made specifically for the Eliseo RTM and RTS Chassis Systems. The Mutant features an extended tenon length for increased barrel thread contact and bedding surface. (Extended tenon is optional on the Rebel). The Mutant’s integral recoil lug adds rigidity and simplifies tubegun assembly. Medium-action Mutants are typically built with a Guardian mag-well cut to accommodate AI and AW magazines, while Long-action Mutants fit AI single-stack magazines and can be of Badger length or the longer CIP length for extended-OAL cartridge loading. The starting price on a Mutant action is $1200.00 (before options), and delivery is at least 60 days out.
The beefy Titan (50 BMG) and Renegade (.408 CheyTac) actions look like they will become very popular with the big-caliber shooters. These jumbo actions share the advanced features of their smaller cousins, but they are sized up significantly to provide additional strength, stiffness, and bedding surface. On both big actions double-plunger ejectors are used in combination with M16 extractors for reliable case ejection. Both Titan and Renegade actions are offered either as a single-shot or repeater. The Titan is currently sold exclusively through Proof Research, while the Renegade is not yet in production. Defiance plans to build 600 Renegade actions later this year, after demand is filled for the Rebels and Mutants. The anticipated price for the Renegade is $1750.00.
OK, we suspect we’ve whet your appetite. For final pricing (with customer-ordered options) and availability call Defiance at (406) 756-2727. For specs, features, and lots more photos, visit DefianceMachine.com. Contact Proof Research, 406-756-9290, with order questions about the 50 BMG Titan action.
.
Share the post "SHOT Show Highlight: New Actions from Defiance Machine"
Remington once again showcased a “civilian” production version of the Remington Arms Chassis System (RACS), first shown at the 2011 SHOT Show. The full-adjustable, modular RACS are designed as drop-in upgrades for any Rem 700 action. A Rem 700 action is clamped directly (metal on metal) to the center section of the RACS, which has a V-block type profile and central magazine well. There are both short-action and long-action versions of RACS. These look nearly identical in design, other than the length of the action section (see photos below by EdLongrange.)
The RACS features a folding stock, with adjustable cheekpiece, LOP, and buttplate height/cant/cast-off. This stock will accept AI magazines which also come with the kit.
No Release Date or Price Yet
What we still don’t have is a firm price and a date when RACS will actually be released to vendors. This system attracted much attention when first introduced, and it appears Remington has made evolutionary upgrades, but right now Remington is still not disclosing a final prices or a reliable delivery date. So keep your figures crossed, but don’t get too excited. Rem’s RACS may remain “vaporware” for an extended time.
Video from SHOT Show 2011
2012 Photos by EdLongRange, used by permission
Share the post "SHOT Show: Remington RACS Modular Stock for Rem 700s"
We met up with Justin Juarez of Kinetic Research Group (KRG), producers of after-market stocks for SAKO TRG 22/42, and the new Whiskey 3 Chassis (W3C) system for Tikka T3 and Remington 700.
We were pleased to get a first-hand look at a Whiskey 3 rifle build because Zak Smith is currently testing a KRG Whiskey-3 tactical rifle for AccurateShooter.com. We hope to publish Zak’s field report in February. While Zak’s W3C-fitted rifle is chambered as a Rem .260, Justin showed us a .223 Rem version with an innovative carbon-wrapped barrel. This rifle, shown at right, recently won a F-TR match — no mean feat for a .223 competing against a field of .308 Win rifles.
The modular W3C combines tool-less adjustments, (length-of-pull and cheek piece height) with good ergonomics and very durable construction. Rounds feed through the reliable AICS-type magazines. The W3C Gen II is currently available in fixed and folding stock versions for Tikka T3 (non-magnum length calibers) and Remington 700 short action (and 700 clones). KRG currently taking pre-orders (no money down required) with an open delivery date for other versions such as the Sako M995/TRG-S and Badger M2008. Price: Fixed $890; Folding $1260.
Share the post "SHOT Show: Whiskey 3 Chassis System from KRG"
For 2012, Pierce Engineering Ltd. plans to offer Titanium (Ti) versions of its popular Remington-footprint custom actions. Just 42% the weight of steel, Titanium is light yet very strong, with a strength to weight ratio of 1.5+. By producing action bodies from Titanium, Pierce Engineering is able to shave eight ounces (8 oz.) off the weight of a long action (compared to 4140 steel). What’s more, Pierce is now working on Titanium internals and Titanium bolt handles. This could bring the total weight savings to nearly one pound (16 ounces).
John Pierce tells us: “To add to weight reduction we will offer a Titanium recoil lug and install a Titanium handle to the bolt, and possibly a lightened firing pin assembly. I really want to get close to a one-pound reduction overall.”
The new Pierce Titanium actions were inspired by customer requests. One domestic customer wanted an ultra-light action for a sheep rifle, while an Aussie buyer requested a Ti XP action for a silhouette pistol build. John Pierce reports: “After many requests and having a bar of Titanium lying on the shelf for more than three years, [I decided] well ‘Why not have a go?'”
Price and Ordering Info
What will the new Titanium actions cost? Expect to pay an extra $350.00 or so above the cost of Pierce’s stainless and chrome-moly actions. John Pierce explains: “Titanium does cost a lot more and Titanium offers challenges in machining and special tooling. We are estimating that a Ti action will sell in the range of $350.00 more than the steel counterpart.” For more info, visit PierceEngineeringLtd.com, email jpierceltd [at] tds.net or call (517) 321-5051. You can also write to the address below:
Modular Driven Technology (MDT) has created a new 6061-T6 aluminum chassis for Rem 700 actions (and Rem 700 clones). MDT’s new TAC21 chassis has four (4) main components: action housing, lower unit (with trigger guard and mag well), forearm, and a quick-detach buttstock adapter that mates with the action housing. The main section has a +20 MOA milspec Picatinny rail on top. The action is seated on a V-Block style base inside the action housing. The short action TAC 21 chassis employs AICS-style magazines for .223 Rem or .308 Win-sized cartridges. The fore-end/handguard allows for free-floating barrels up to 1.350″ diameter. The chassis is built to accept any AR15/M16 stock and pistol grip.
Purchase from Sinclair Starting at $849.99
Currently Sinclair Int’l is the exclusive USA distributor of MDT’s TAC21 chassis. Sinclair’s price for the short-action version (right-hand or left-hand) is $849.99, while the long-action version will be $942.99. At present, only short action-versions are in stock, but MDT will be making long-action versions soon, and Sinclair is taking pre-orders. NOTE: these prices do NOT include buttstock, barrel, action, trigger, or optics. For more information, visit www.mdttac.com.
TAC21 Performs Well for Varmint Hunting
Al Voth from the Coyote School Blog did a field test of a .204 Ruger rifle built with the TAC21 chassis and conventional wood buttstock. Voth was able to assemble the rifle in 40 minutes with the MDT chassis kit and “everything fit perfectly.” CLICK HERE to Read Coyote School TAC21 Review.
Share the post "MDT Offers New TAC21 Chassis for Rem 700 Actions"
What are the hottest-selling firearms in the “previously-owned” marketplace? As you might expect, the Remington Model 700 tops the list as the best-selling used bolt action rifle. The leading semi-auto rifle is the little Ruger 10/22 rimfire, followed by another Ruger, the Mini-14. Despite the high cost ($2K+ for the best examples) the Colt Python is the best selling used revolver. (People have realized that Pythons have proven to be good investments.)
CG Mod 22 Trigger Installation Tips
Adjustable Trigger with Insert
We met up with Justin Juarez of 
