June 20th, 2019

How To Pull Bullets Using Press-Mounted Collet Tools

Collet Bullet Puller Hornady RCBS Press Mount Reloading

Do you have some ammo that got loaded incorrectly, perhaps with the wrong powder? Then you’ll want to disassemble the ammo for safety’s sake. You can use an impact puller to do this task, but if you have more than a dozen rounds or so, you may prefer to use a collet-style bullet puller. These work very quickly and positively, making quick work of big jobs. The efficiency of the collet-style puller is worth the investment if you frequently disassemble ammo. These devices retail for under $25.00 (collets sold separately). Normally, you’ll need a specific collet for each bullet diameter. But collets are not that costly, so this isn’t a big deal, particularly if you only load a few calibers, such as .223, 6mm, and .308.

Hornady and RCBS use different mechanisms to tighten the collet around the bullet. On Hornady’s Cam-Lock Bullet Puller, a lever-arm on the top of the bullet puller serves to tighten the collet around the bullet. Simply rotate the lever from the vertical to the horizontal position to grab the bullet. Lower the ram to remove the case. The bullet will drop out when you return the lever arm to the vertical position. This is demonstrated in the video below:

Hornady Cam-Lock Bullet Puller Demonstrated

Collet bullet-pullers resemble a loading die with a lever or handle on the top. They screw into a standard reloading press. Hornady and RCBS both make collet-style bullet pullers. They use the same basic principle — the device tightens a collet around the bullet, and then the bullet is separated from the case by lowering the press ram. NOTE: Collet pullers may leave small marks on your bullets, unlike impact (kinetic) pullers.*

Hornady collet bullet pullerLike the Hornady tool, the RCBS Bullet Puller employs a collet to grab the bullet. However, the RCBS tool tightens the collet in a different way. The head of the RCBS tool is threaded internally. By rotating the lever arm clockwise in a horizontal circle you squeeze the collet around the bullet. To remove the bullet, after lowering the press ram, simply spin the lever arm back in the opposite direction. The use of the RCBS tool is demonstrated in this video:

RCBS Collet Bullet Puller Demonstrated:

WARNING: When removing bullets from loaded cartridges, always make sure there are no obstructions or debris in your shell-holder or under the loaded round. NEVER engage a primer seating accessory on your press when working with loaded rounds. You can cause a round to discharge by contacting the primer! Also, we recommend you keep your head and torso away from the bullet puller tool at all times.

*By contrast, impact pullers rarely mark bullets, particularly if you put a little bit of foam or paper wadding in the closed end of your impact puller. When dismantling loaded rounds, powder kernels can get trapped in the wadding, so you should remove and replace the wadding before changing to cartridges loaded with a different powder type (assuming you intend to save the powder).

Permalink Reloading, Tech Tip 1 Comment »
January 21st, 2018

Pulling Bullets Safely and Efficiently with a Collet Puller

Hornady cam-lock bullet puller ammunition UlimateReloader

When you make a reloading mistake, you may need to “pull down” assembled ammo. The embedded UltimateReloader.com video demonstrates how to use the Hornady Cam-Lock bullet pulling system.

When Reloading Goes Bad — The Danger of Over-Charging
Our friend Gavin Gear of UltimateReloader.com was recently reloading some 9mm pistol ammo with his Hornady progressive press. As part of his reloading procedure, he visually checks the cases — and he noticed that the charges seemed high. Sure enough, his most recently-produced rounds were about two grains over spec. He diagnosed the issue: “I was using a powder measure without a baffle. What happened was, over the course of the loading session, things settled in, and the charge level increased.”

Not knowing just when his powder measure started delivering too much powder, Gavin decided, for safety’s sake, to pull down all the ammo he had just reloaded. Yes that’s time-consuming, but it’s better than the alternative — having a dangerous Kaboom while shooting. With fast-burning pistol powders, a two-grain over-charge could cause a blown case, damaged firearm, and/or serious injury.

Watch Cam-Lock Bullet Puller Used to Remove Bullets from Loaded Ammo:

Use of Bullet Puller starts 4:00 minutes into video.

Gavin says it is vitally important to perform safety checks during the reloading process: “You’ve got to do it — check every single round to make sure there IS powder, and that there’s not too MUCH powder. Double, Triple, Quadruple check your components… and your powder charges. You can’t be too careful.”

To pull down a loaded round, first place the cartridge in the shellholder on your press ram. Then raise the round up into the bullet puller device installed where a die would go. The Hornady Cam-lock bullet puller works by clamping the bullet in a collet when you flip down the red-coated lever. Then, with the case held by the rim in the shell-holder, the bullet exits the cartridge as the press ram is lowered. It takes time, but it’s pretty fool-proof once you get the hang of it. This entire process is illustrated in Gavin’s video, starting near the four-minute mark.

Hornady Cam-Lock Bullet puller Gavin Gear Ultimate Reloder.com

The Hornady Cam Lock Bullet Puller has four (4) key components: 1. Cam-Lock die body; 2. Cam-Lock lever; 3. Stem; and 4. Collet (Caliber-specific).

NOTE: In order to use this tool, you’ll need the appropriate collet for each diameter range of bullets you intend to pull. For example use collet #3 for 6mm, collect #6 for 7mm, and collet #7 for .308 Caliber.

Hornady cam-lock bullet puller ammunition UlimateReloader

Permalink - Videos, Reloading, Tech Tip 1 Comment »
April 27th, 2016

Press-Mounted Bullet Pullers — How to Use Them

Collet Bullet Puller Hornady RCBS Press Mount Reloading

In our Shooters’ Forum, a member recently noted that he needed to pull down (disassemble) some ammunition that was loaded incorrectly by one of his shooting buddies. You can use an impact puller to do this task, but if you have more than a dozen rounds or so, you may prefer to use a collet-style bullet puller. These work very quickly and positively, making quick work of big jobs. The efficiency of the collet-style puller is worth the investment if you frequently disassemble ammo. These devices retail for under $25.00 (collets sold separately). Normally, you’ll need a specific collet for each bullet diameter. But collets are not that costly, so this isn’t a big deal, particularly if you only load a few calibers, such as .223, 6mm, and .308.

Hornady and RCBS use different mechanisms to tighten the collet around the bullet. On Hornady’s Cam-Lock Bullet Puller, a lever-arm on the top of the bullet puller serves to tighten the collet around the bullet. Simply rotate the lever from the vertical to the horizontal position to grab the bullet. Lower the ram to remove the case. The bullet will drop out when you return the lever arm to the vertical position. This is demonstrated in the video below:

Hornady Cam-Lock Bullet Puller Demonstrated

Collet bullet-pullers resemble a loading die with a lever or handle on the top. They screw into a standard reloading press. Hornady and RCBS both make collet-style bullet pullers. They use the same basic principle — the device tightens a collet around the bullet, and then the bullet is separated from the case by lowering the press ram. NOTE: Collet pullers may leave small marks on your bullets, unlike impact (kinetic) pullers.*

Hornady collet bullet pullerLike the Hornady tool, the RCBS Bullet Puller employs a collet to grab the bullet. However, the RCBS tool tightens the collet in a different way. The head of the RCBS tool is threaded internally. By rotating the lever arm clockwise in a horizontal circle you squeeze the collet around the bullet. To remove the bullet, after lowering the press ram, simply spin the lever arm back in the opposite direction. The use of the RCBS tool is demonstrated in this video:

RCBS Collet Bullet Puller Demonstrated:

WARNING: When removing bullets from loaded cartridges, always make sure there are no obsructions or debris in your shell-holder or under the loaded round. NEVER engage a primer seating accessory on your press when working with loaded rounds. You can cause a round to discharge by contacting the primer! Also, we recommend you keep your head and torso away from the bullet puller tool at all times.

*By contrast, impact pullers rarely mark bullets, particularly if you put a little bit of foam or paper wadding in the closed end of your impact puller. When dismantling loaded rounds, powder kernels can get trapped in the wadding, so you should remove and replace the wadding before changing to cartridges loaded with a different powder type (assuming you intend to save the powder).

Permalink Bullets, Brass, Ammo, Reloading, Tech Tip No Comments »
June 10th, 2015

How to Use Press-Mounted Bullet-Pulling Tools

Collet Bullet Puller Hornady RCBS Press Mount Reloading

In our Shooters’ Forum, a member recently noted that he needed to pull down (disassemble) some ammunition that was loaded incorrectly by one of his shooting buddies. You can use an impact puller to do this task, but if you have more than a dozen rounds or so, you may prefer to use a collet-style bullet puller. These work very quickly and positively, making quick work of big jobs. The efficiency of the collet-style puller is worth the investment if you frequently disassemble ammo. These devices retail for under $25.00 (collets sold separately). Normally, you’ll need a specific collet for each bullet diameter. But collets are not that costly, so this isn’t a big deal, particularly if you only load a few calibers, such as .223, 6mm, and .308.

Hornady and RCBS use different mechanisms to tighten the collet around the bullet. On Hornady’s Cam-Lock Bullet Puller, a lever-arm on the top of the bullet puller serves to tighten the collet around the bullet. Simply rotate the lever from the vertical to the horizontal position to grab the bullet. Lower the ram to remove the case. The bullet will drop out when you return the lever arm to the vertical position. This is demonstrated in the video below:

Hornady Cam-Lock Bullet Puller Demonstrated

(more…)

Permalink Bullets, Brass, Ammo, Reloading No Comments »
April 4th, 2013

Reloading TIP: Use Shell Holder with Impact Puller

Here’s a clever tip from Theodor Pettersen, one of our readers from Norway. Theodor writes: “I am an Norwegian shooter and reloader with 40 years of experience and practice. I would like to pass on a tip on how to improve the kinetic bullet puller (also known as an ‘impact puller’). Most of them use a 3-section collet which has three jaws held together with a rubber ring. It is very time-consuming when they pull apart, and have to be put together.

The three-piece collet can be exchanged with a shell holder that fits the cartridge from which you need to remove a bullet. The shell holder fits right into my RCBS bullet puller, and is much easier to use. I think it also will fit other makes of impact pullers.”

Thanks for the tip Theodore. We’ve tried it with a MidwayUSA-brand impact bullet puller and it works. We agree that the collets can be awkward to use, as the jaws can flip over when you’re installing the rubber retaining ring. Still, this editor normally prefers to use the collet, because it seems to be faster than a shellholder — so long as the rubber ring stays in place. The shellholder method is a good alternative though — if you’ve lost your collets or don’t have one that fits your brass.

Quick TIP: For ballistic tip bullets or bullets with tightly-pointed meplats, try putting a small wad of paper (or closed-cell foam) in the bottom of the impact puller chamber. This will cushion the bullet tip, preventing damage when the bullet drops out of the case.

Kinetic Bullet Puller in Operation
Never used a kinetic bullet puller before? Here’s a video that shows you the proper technique. The best surface for the impact is something like a linoleum floor — very firm but not so hard that the plastic head cracks on impact. Note: In this video demo, there is no powder in the cartridge. If you are pulling bullets, powder will come out and you’ll want to have a pan to pour that into, as you recover the bullet.

YouTube Preview Image
Permalink Reloading, Tech Tip 8 Comments »