This website focuses on rifle accuracy and precision — normally indicated by small groups and high scores. But sometimes reactive targets are fun too — particularly when you can hit them at very long range. Here’s a video of a 6-6.5×47 Lapua hitting a milk jug at 1000 yards. This video was filmed during the Long Range Shooters of Utah 1000-Yard Milk Jug Challenge a while back. A remote camera shows a 95gr Sierra MatchKing penetrating a filled jug. The jug was hit with the fifth shot — you can see the fluid leaking out at 0:57. NOTE: Because the remote camera is positioned well off to the side, the jug-penetrating shot appears to impact low and slightly right (as seen in the inset close-up frame). The jug is actually suspended in front of the white square, and that’s where the fifth shot went, right through the bottom section of the jug.
Congrats to Mr. Clint Bryant of Green River, Wyoming for hitting the jug in challenging conditions. Clint had to dial 11 minutes of windage to compensate for a strong cross-wind (see 2:30 time-mark). Clint’s 6-6.5×47 cartridge is a variant of the 6.5×47 Lapua cartridge, necked down to 6mm. This 6-6.5×47 case drives the 95gr SMKs at 3100 FPS, making for a very effective (and accurate) coyote cartridge. Rick’s rifle was a Savage Model 12, with 30″ barrel, in an aftermarket stock, topped by a Leupold scope.
Here is the parent case, the 6.5×47 Lapua:
Share the post "6-6.5×47 vs. Milk Jug at 1000 Yards in Crazy Winds"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. CDNN — DPMS A15, Magpul Stock, Match Trigger, $499.89
The DPMS A15 is a good basis for a .223 Rem varmint rifle. It’s an excellent value at $499.89, given the components. The Magpul stock works well with a rear bag. And we like the 1:9″-twist 24″ stainless barrel with target crown. For varminting, it’s nice to have a 24″ barrel for extra velocity. Be aware this barrel has an unusual triangular profile forward of the handguard. This DPMS rig also features a 2-stage Bushmaster target trigger and durable Cerakote finish. NOTE: This is NOT a complete rifle — you need to supply a bolt carrier group and charging handle. But if you already own an AR15, you can use those components.
2. MidwayUSA — Dual Steel Gong System with Frame, $71.99
Who doesn’t like shooting steel? The “clang” of hitting a steel target at long range provides instant gratification. This patented Viking Solutions Gong Target System features two 3/8″-thick, AR500 Steel Gongs (8″ and 10″) suspended by chains. The support frame consists of 2 leg stands and 2 crossbar sections. Assembled, the crossbar is 32″ above ground level. Right now this unit is on sale for $71.99 — 20% off the regular price.
3. Natchez — Big Weaver Scope Sale, Save Hundreds
Weaver makes very good optics for a variety of disciplines — hunting, tactical, even benchrest. With Natchez’s June Weaver Optics Sale you can save up to $585! For centerfire benchrest the 48X T-Series XR scope can do the job at 1/3 the price of a Leupold. And for rimfire benchrest rifle, the 24X Weaver T-Series XR is a fine choice. Hunters will find suitable Weaver zoom scopes at crazy low prices. The 3-9x40mm Kaspa Hunting Series scope is just $79.99 on sale.
4. Midsouth Shooters — SK .22 LR Rimfire Ammo Sale
Right now Midsouth is running a big SALE on SK .22 LR Rimfire ammo. This quality ammo has shown fine accuracy in our rifles. A variety of types are offered starting at $5.59 for 50 rounds. For target rifles we recommend SK Flat-Nose Target ammo at $7.10 per box or $64.79 for 500 rounds. For many folks it performs close to high-end match ammo costing much more. Also, if you are looking for bulk .22 LR ammo, you can get 1000 rounds of Browning BPR 36gr copper-plated HP ammo for just$44.99 at Cabela’s. That’s just 4.5 cents per round.
Varminters rejoice! Here is a killer deal on excellent “dogtown” bullets. These 55gr .224-caliber V-Max bullets deliver explosive results on ground squirrels, p-dogs, and other small varmints. The BC is pretty low, but you can drive these V-Maxs over 3300 FPS with a standard .223 Rem cartridge using Varget or CFE223. With this sale, you can grab these excellent bullets for less than $17 per hundred — that’s a steal. If you’re a V-Max fan, act soon before this deal sells out.
6. Amazon — The Wind Book for Rifle Shooters, $22.99
This is the NEW May 2020 Edition, Just Released!
Readers often ask: “Is there a good, easy-to-comprehend book that can help my wind-reading?” Many of our Forum members have recommended The Wind Book for Rifle Shooters by Linda Miller and Keith Cunningham. Other books cover wind reading in a broader discussion of ballistics or long-range shooting. But the Miller & Cunningham book is ALL about wind reading from cover to cover, and that is its strength. The book focuses on real world skills that can help you accurately gauge wind angle, wind velocity, and wind cycles. Here’s a video review explaining what makes this book so good.
Need a small vertical safe for your workshop, loading room, remote cabin, or RV? This Legend Range & Field 4-Gun Safe can fill the bill. It has an electronic lock and backup key, and secures with five 1″ locking bolt. This small safe also includes a bolt-down kit for added security. At $183.30 this safe offers significantly more protection than a thin-walled security locker, for not much more money. Save $37 with this promotion at Gander Outdoors. NOTE: If you have the safe shipped to your house, there is a $50.00 Shipping Fee. Exterior Dimensions: 55″H x 11.6″W x 11″D
8. Cabela’s — Catch-All Gear Bag $12.99, Many Colors
This versatile bag holds lots of gear, and you can’t beat the price — just $12.99. At 16″x10″x6″ it’s big enough to hold rifle ammo, muffs, a Kestrel, and other accessories. It can also serve as a general utility bag for car camping trips. Six exterior pockets, including zippered mesh pockets on top and side, provide multiple storage options.Sturdy 1-1⁄2″ nylon web carry straps can be joined by a hand-friendly wrap handle. Cabela’s Catch-All Gear Bag available in a variety of colors including True Timber Camo, 02 Octane Camo (3 versions), Lt. Gray, Blue, Green, Tan, Orange Gold, and Dark Gray.
Here’s a great Father’s Day gift that you and your Dad can use together. Walkie-Talkies are “must-have” items for long-range shooting. The 22-CH Motorola T100 Two-Way Radio is an Amazon Favorite among FRS/GMRS Handheld Radios. Motorola says the T100 has a range up to 16 miles (with ideal conditions), and the T100 units can receive communications from all FRS/GMRS two-way radios. Price for a Two-Radio T100 Set is just $29.00
10. Brownells — Wipeout Foam Cleaner, $14.99
Walking the firing line of the Berger SW Nationals this year, one cleaning product was mentioned over and over again and for good reason. Sharp Shoot R Wipe-Out foaming bore cleaner is a no-nonsense, easy-to-use bore cleaner that does a great job. We get best results with two applications of Wipe-Out after some wet patches. If you’re tired of long brushing sessions, give Wipe-Out a try — it really reduces brushing required. This is a great deal. The same 5 oz. can is $23.95 on Amazon.
Share the post "Bargain Finder 247: AccurateShooter’s Deals of the Week"
Good news — shooting clubs can once again hold NRA-sanctioned matches at their facilities. The NRA is now accepting tournament registrations for events to be held July 1, 2020 or later. This is good news for high power competitors, smallbore shooters, silhouette shooters, air rifle competitors, BPCR marksmen, and target pistol shooters.
The NRA has announced that beginning June 15, 2020, the NRA Competitive Shooting Division will begin accepting tournament registrations for sanctioned matches taking place on or after July 1, 2020. Clubs and match directors are urged to comply with federal, state and local guidelines regarding the COVID-19 pandemic. The NRA will continue to monitor the COVID-19 situation and/or make additional statements as needed. Please contact the NRA Competitive Shooting Division at comphelp@nrahq.org, visit the website at Competitions.NRA.org.
You’ll find current news, event info, and shooting tips on the NRA Competitive Shooting Facebook Page. There is also a large photo archive and many videos showing shooters in action at matches. Topics are shown on the left below:
Click Image to visit NRA Competitive Shooting Facebook Page.
NRA Sanctioned Tournaments are a series of matches covered by an official program. Such matches may be all individual matches, all team matches, or a combination of both. They may be all fired matches or a combination of fired and aggregate matches. A tournament may be conducted on one day or successive days.
Registered Tournaments, Approved Tournaments, Regional Championships, Sectional Championships and Sanctioned Leagues may be authorized by the NRA after application has been filed by a local group or organization. See the NRA rules for specific rule questions.
Share the post "NRA Resumes Match Registrations for Sanctioned Events"
Gage Pin Die System Product Review by F-Class John
Consistent neck tension is often considered key to precision reloading. Neck tension (or interference as it’s more accurately known) helps ensure that the bullet is held with a known amount of pressure ensuring a consistent release each time. The more common expansion method employs expander mandrels. However, there is another lesser-known but very effective method — using GAGE PINS. This article reviews a unique Porter’s Precision Products Reloading Die designed to work with high-quality Gage Pins.
Gage Pins, long-time tool of machinists, are used to measure the size of a bored hole. They come in a variety of sizes and classes. In the reloading world, most people use ZZ Gage Pins that are sized .0005″ apart and are accurate to .0002″. The nice thing about Gage Pins is that you can order them in either a + or – size which means their accuracy errors on one side or the other so by ordering sets of + and – you can effectively make half-sizes. It’s this flexibility and great range of sizes that make Gage Pins so attractive.
For all the good that Gage Pins can do, until now there has not been a handy way to use them in a reloading press. Some folks tried using a bullet puller to hold the Gage Pin. But on many presses, this can be inconvenient because of long handles or unusual height requirements. As a result, I have mostly resorted to using conventional expander mandrels.
But now I have started using precision Gage Pins, thanks to a special new Gage Pin die system from Porter’s Precision Products in Texas. Not long ago I received a video from a friend showing someone using a custom die specifically made for holding Gage Pins. It turns out that Porter’s Precision Products out of Texas makes a custom Gage Pin Die product that consists of a die body, collet, and die cap. Porter’s Precision also sell a wide range of Gage Pins that have been nicely tapered to prevent damage to brass.
Using the Porter’s Precision Gauge Pin Die for Expanding Necks
Using the Porter’s Precision Gage Pin die is pretty straight forward with one caveat. The instructions are very clear that the collet must be inserted at an angle into the threaded cap to help ensure it tightens correctly otherwise damage to the collet may occur. Once you do this a couple times it becomes very simple and shouldn’t be a concern, especially since there’s rarely a ready to actually remove the collet unless you’re changing from one caliber range to another.
With the cap and collet now threaded onto the die body, choose the Gage Pin you want to use, insert it into the collet and tighten the cap down. Once the pin is where you want it, use a set of wrenches to firmly tighten the cap down and you’re ready to go. Thread the die in your press and simply adjust the height to ensure the Gage Pin is being inserted fully into the neck of your brass. You want to make sure the entire neck is being expanded without damaging the rim by pushing it to far up inside the die.
General Thoughts — Gage Pins vs. Expander Mandrels
The actual use of Gage Pins on case neck doesn’t vary from expander mandrels. They both accomplish the same goal and which tool you choose really comes down to personal preference. Where Gage Pins really shine is in their durability and the vast selection of sizes/diameters/tolerances. You can even find long-wearing, reduced friction carbide Gage Pins, but they do cost more.
For me, using the Porter’s Precision Die allowed smooth operation and Porter’s Gage Pins are really well-made. This makes expanding a dream even without any lube in the necks (although I still recommend lube when using a steel Gage Pin, as opposed to carbide). If you’ve been in the market for a way to help expand your necks with enhanced consistency, give Gage Pins a try using the Porter’s Precision Gage Pin Die.
Share the post "Precise Neck Expansion with Gage Pin Die from Porter’s Precision"
A multi-time F-TR National Champion, James “Jimmy” Crofts is one of America’s top F-Class competitors. And now this F-TR ace has a stunning new rifle in his arsenal. AccurateShooter Forum member CigarCop, head honcho of KW Precision LLC, recently completed a new F-TR rig for Crofts. This handsome, state-of-the-art rifle features top-tier components: Borden action, twin Brux barrels, Cerus RifleWorks F-TR Stock, and Jewell trigger, all resting on a wide-base Phoenix Bipod.
James Crofts photo by Kent Reeve.
Have a good look at these photos below. Yes, envy is the appropriate reaction. With the smooth operation of the Borden action and the predictable accuracy of Brux barrels, we bet James’s new rig will shoot as good as it looks.
CigarCop actually chambered two barrels for James, with different fluting patterns — conventional linear flutes for one tube, and lines of staggered ovals for the other. Finished length for both barrels is 30″. Yes it looks cool, but the fluting was done mainly to save weight with the 30″-long lengths. CigarCop tells us the complete rifle, without scope and rings, weighs just under 15 pounds. Max allowed weight for an F-TR rifle, with scope, is 18.18 pounds (8.25 kg).
When James Crofts is not shooting his .308 Win F-TR rig,
he often trains with a .22 LR Rimfire rifle. Read on…
Rimfire Training for F-Class Competitors
2014 and 2012 U.S. National F-TR Champion James Crofts is one of America’s top F-Class shooters. A member of 2013 World Championship-winning F-TR Team USA squad, James knows a thing or two about long-range shooting. But you may be surprised to learn how James sharpens his shooting skills at relatively short distances. You see, James often practices with a .22 LR rimfire rifle at distances from 50 to 200 yards. James tells us: “Shooting my F-Class rimfire trainer saves me money and improves my shot process and wind-reading abilities.”
Remington rimfire 40X barreled action in PR&T LowBoy stock with PT&G bolt.
Rimfire Training Teaches Wind-Reading Skillsby James Crofts
Training with the rimfire is extremely useful and can be done from 25 yards out to 200 yards. I am lucky and can shoot 50 yards right off my back deck. That is far enough that any miscue on rifle handling will show up on the target. I use a two dry-fire to one actual shot routine for my practices. This gives me much more positive reinforcement without any negative reinforcement.
Wind reading is extremely important with a .22 LR rifle. I use a set of smallbore flags to aid my wind calls. The smallbore flags are a must and force you to look at the flags and mirage on each and every shot.
This Rimfire rifle features a CMP-sourced Rem 40X barreled action, PR&T Low Boy stock, Jewell trigger, and Phoenix bipod. The gun was built by Ray Bowman of Precision Rifle & Tool. James Crofts told us: “The project turned out awesome — the rifle was a hammer from the beginning even with the stock barrel.”
Rimfire Training Is Cost-Effective
Rimfire ammunition is much less costly than centerfire ammo. Though .22 LR prices have risen, you can still get a 500-round brick of very good .22 LR match ammo for around $75.00. That works out to fifteen cents a round. That’s a fraction of the cost of handloading .308 Win match ammo. The top match-grade, .308-cal centerfire bullets can cost around $60 per hundred. Then you have to figure in brass, primers, and powder. Finally you have to consider your precious centerfire barrel life lost to practice.
Share the post "Sunday GunDay: Handsome F-TR Rig Built for James Crofts"
We are coming into peak Prairie Dog season. For long shots you’ll definitely want a centerfire. We like the 20 Practical in an AR and a 22 BR/BRA in a bolt-action. That will have you covered out to 700 yards. But for shorter shots on small critters — say inside 150 yards — it makes sense to have an accurate 17 HMR rimfire rig. Today’s 17 HMRs are capable of surprising accuracy, rivaling a good centerfire rig, but with less recoil and much lower cost per shot. And the 17 HMR offers more than double the velocity of a .22 LR — up to 2650 fps with a 17-grain bullet.
Top Shot former Champion Dustin Ellerman likes his Volquartsens, and we can see why. With one of his favorite 17 HMR rimfire varmint rigs, he’s seen some outstanding accuracy with CCI ammo. A few seasons back, on his Facebook page, Dustin reported: “Prepping for prairie dogs and I’m floored by this cold, sub-half-inch group shot with the Volquartsen Custom 17 HMR at 100 yards.” This thumbhole-stock rifle features a Bowers Group USS suppressor, and 3-12x56mm Meopta Scope. Dustin tried different types of CCI 17 HMR ammo. This small group was shot with CCI A17 ammo.
What’s the effective range of a 17 HMR on prairie dogs? You might be surprised. in 2015, Dustin took another Volquartsen 17 HMR on a Prairie Dog hunt in Wyoming. He was impressed with the rifle (shown below) and the little rimfire cartridge. Dustin says the effective range of the 17 HMR is farther than one might expect: “I made hits out to 300 yards. 200 yards was easy as long as the wind wasn’t too bad.”
Here’s the Volquartsen 17 HMR Dustin used in Wyoming in 2015:
After that 2015 P-Dog expedition, Dustin became a fan of the 17 HMR cartridge: “Never paid it much attention before now because the ammo is five times more expensive than .22 LR and I mostly target shoot. However, for prairie dogs, the 17 HMR is amazing!” Consider this — Hornady’s 17 HMR ammo pushes a 17gr V-Max bullet at 2550 fps, twice as fast as typical .22 LR rounds.
Prairie Dog Adventure with Savage A17
This video shows a successful Prairie Dog hunt. Watch and you’ll see hits out to 160 yards (00:50), proving the effective range of the 17 HMR cartridge. The host is shooting a Savage A17 semi-auto 17 HMR rifle in a Boyds laminated stock.
Share the post "Got a P-Dog Trip Planned? Bring along a 17 HMR Rimfire Rig"
June is National Firearms Safety Month. As part of that effort, the National Shooting Sports Foundation (NSSF) has prepared tips for gun owners transporting firearms in their vehicles. Project ChildSafe and NSSF are emphasizing gun safety as National Safety Month kicks off, and as the nationwide surge in firearm sales continues and includes millions of first-time buyers.
HERE Are Key Guidelines for Safe, Secure Handling of Firearms in Vehicles:
• Take note of and safely control the muzzle direction of firearms in vehicles. This is one of the main rules of gun safety and applies to the inside of vehicles as well as any other location.
• When finished using your firearm outside your vehicle, unload it before you re-enter your vehicle.
• Even after a long hunt or a day in the sun at the range, always check, and then double check, that guns are unloaded before placing them in a car or truck.
• Be very careful if you must unload a firearm in the confined space of a vehicle so as not to have an accidental discharge. If your location allows, it is safer and easier to unload the firearm outside the vehicle.
• Never leave firearms in parts of the vehicle accessible to children or pets.
• Keep firearms and ammunition out of sight to avoid tempting thieves.
• Use secure temporary storage for firearms in vehicles.
• A lockable gun case or a lock box may be the most practical choice to securely store a gun in a vehicle. These come in a range of prices and models.
• If you’re concerned about quick access to your firearm, many types of lockable safes allow for extremely fast access of your gun while at the same time helping to prevent unauthorized access.
• Secure the lock box to the vehicle, if possible. Some companies make custom concealed compartments for specific model vehicles.
Storing Firearms in Vehicles to Prevent Theft and Misuse
We travel with our firearms all the time, taking them to the range, on hunting trips or carrying them on our person, as permitted by law. As a result, there will be times when you might have to leave your firearm in your vehicle. This creates a situation that deserves careful consideration. The last thing you want is to have your gun stolen and potentially misused by a criminal. In some states, you could even be subject under the law to serious penalties and fines for failure to properly secure a firearm. Unfortunately, thefts of firearms from vehicles are on the rise. Thieves commonly steal cars and trucks even when they don’t obviously contain firearms — a reminder that vehicle door locks are not totally secure.
As a responsible gun owner concerned about your firearms falling into the wrong hands, it’s best to always remember this rule: Your firearm must be under your control at all times; when it’s not, it should be placed in locked storage and out of sight. Locking the doors on your vehicle does not constitute secure firearm storage. As one writer put it: “Cars and trucks aren’t safes. And they’re not holsters. They’re not storage containers.”
The glove compartment or console of your car or truck, even if lockable, should not be considered a secure storage device either, as it can be pried open too easily. If you need to leave your firearm in a vehicle, here are some important safety considerations to keep in mind to help prevent theft and unauthorized access.
Share the post "How to Store and Transport Firearms Safely in Vehicles"
Many guys getting started in long range shooting are confused about what kind of scope they should buy — specifically whether it should have MIL-based clicks or MOA-based clicks. Before you can make that decision, you need to understand the terminology. This article, with a video by Bryan Litz, explains MILS and MOA so you can choose the right type of scope for your intended application.
You probably know that MOA stands for “Minute of Angle” (or more precisely “minute of arc”), but could you define the terms “Milrad” or “MIL”? In his latest video, Bryan Litz of Applied Ballitics explains MOA and MILs (short for “milliradians”). Bryan defines those terms and explains how they are used. One MOA is an angular measurement (1/60th of one degree) that subtends 1.047″ at 100 yards. One MIL (i.e. one milliradian) subtends 1/10th meter at 100 meters; that means that 0.1 Mil is one centimeter (1 cm) at 100 meters. Is one angular measurement system better than another? Not necessarily… Bryan explains that Mildot scopes may be handy for ranging, but scopes with MOA-based clicks work just fine for precision work at known distances. Also because one MOA is almost exactly one inch at 100 yards, the MOA system is convenient for expressing a rifle’s accuracy. By common parlance, a “half-MOA” rifle can shoot groups that are 1/2-inch (or smaller) at 100 yards.
What is a “Minute” of Angle?
When talking about angular degrees, a “minute” is simply 1/60th. So a “Minute of Angle” is simply 1/60th of one degree of a central angle, measured either up and down (for elevation) or side to side (for windage). At 100 yards, 1 MOA equals 1.047″ on the target. This is often rounded to one inch for simplicity. Say, for example, you click up 1 MOA (four clicks on a 1/4-MOA scope). That is roughly 1 inch at 100 yards, or roughly 4 inches at 400 yards, since the target area measured by an MOA subtension increases with the distance.
MIL vs. MOA for Target Ranging
MIL or MOA — which angular measuring system is better for target ranging (and hold-offs)? In a recent article on his PrecisionRifleBlog.com website, Cal Zant tackles that question. Analyzing the pros and cons of each, Zant concludes that both systems work well, provided you have compatible click values on your scope. Zant does note that a 1/4 MOA division is “slightly more precise” than 1/10th mil, but that’s really not a big deal: “Technically, 1/4 MOA clicks provide a little finer adjustments than 1/10 MIL. This difference is very slight… it only equates to 0.1″ difference in adjustments at 100 yards or 1″ at 1,000 yards[.]” Zant adds that, in practical terms, both 1/4-MOA clicks and 1/10th-MIL clicks work well in the field: “Most shooters agree that 1/4 MOA or 1/10 MIL are both right around that sweet spot.”
The National Rifle Association (NRA) has announced that the 149th Annual Meeting of Members, previously scheduled in Nashville, TN in April, has been rescheduled for Saturday, September 5, 2020 in Springfield, Missouri. The 2020 NRA Annual Meeting will be held at the Springfield Expo Center. The NRA has not yet released a full schedule of events. But this will be a meeting of members only — not a large trade show with entertainment and celebrity guests.
We’re told that this will be a much smaller event than originally planned for April 16-19 in Nashville. The rescheduled NRA Meeting will take place in Halls A/B/C at the Springfield Expo Center at 635 E. Saint Louis Street, Springfield, Missouri. The meeting will sart 9/5/20 at 9:00 am Central Time. All NRA members are invited to attend.
The Springfield News Leader reported that this event will NOT be a large trade show. It will be a meeting of members only — there will be no large trade show with hundreds of exhibitors.
Dana Maugans with the Springfield Visitors and Convention Bureau, said that, due to the COVID-19 pandemic, the NRA had to cancel the large NRA Convention originally scheduled for April in Nashville. “But with their bylaws, [the NRA] still has to have the membership meeting,” Maugans said. “They are going to have their membership portion of the meeting here. But it will not be nearly as large as the Convention/Trade Show that was planned.” Maugans revealed that, to allow for social distancing, the NRA reserved double the amount of space normally need for the 1,000 to 1,250 people expected to attend.
Share the post "NRA Annual Meeting Set for September 5, 2020 in Missouri"
Sightron’s Latest and Greatest Long Range Scope Field Test and Review by James Mock
When I was writing for Precision Shooting Magazine I appreciated those vendors who would trust me to test their products. One such person was Alan Orr of Sightron. Alan was willing to send his scopes to me for testing and I found them to be some of the best values. I have shot Sightron’s SII 36X BR, the Sightron SIII 10-50x60mm Long Range (30mm tube). Recently I tested latest and greatest (in my opinion) high-magnification Sightron — the SVSS ED 10-50x60mm with MOA-H reticle. This unit boasts ED Glass and has a fat 34mm main tube.
Sightron’s SIII 10-50x60mm riflescope (30mm tube) is a fine value at $1050-$1190 street price. That popular 10X-50X LR optic (PHOTO HERE) delivers great performance for the price. However, long range shooters wanted more and Sightron has delivered with the new-generation SVSS ED 10-50x60mm ZS MOA-H optic (34mm tube). This impressive new scope features higher-grade ED (Extra Low-Dispersion) glass and many great features. These features include illuminated reticle, zero stop, and FAST parallax adjustments with coarse and fine adjustments. Also, there is a locking windage turret for the models NOT fitted with zero stop. I tested the Zero-Stop (ZS) version.
This new scope has exactly what I look for in a scope since most of my shooting is at 600 yards. This boasts Sightron’s proprietary “Exact Track” and a 7-layer lens coatings. One feature that is drawing rave reviews is the new parallax side focus control. This employs BOTH a coarse and a fine adjustment, as found on premium spotting scopes. This seems like a minor point, but it allows one to fine-tune the parallax with little effort. This, along with the fast-focus eye piece, enables one to get a crystal clear and sharp image quickly. The 1/8 MOA clicks are positive and the clicks are very audible.
Review in a Nutshell — This scope is amazing and I have used some of the best scopes to be found. It is as good or better than some scopes costing $1200-$1500 more. What does a Sightron 10-50X SVSS ED cost? If you shop around aggressively you can find the basic (non-illuminated) version for under $2000 (See footnote*). I know that seems like a lot of money and it is, but this product represents true value, as it performs with scopes costing $1000 more.
With its large 60mm objective lens with ED glass and the 7-layer coating, this scope has the brightest image of any that I have tested at high power settings. (Of course there are premium scopes that I have not yet tested that may equal or exceed this one.) A person must choose a scope best suited for the type of shooting planned. For long range benchrest competition, I don’t think that there are many optics that exceed the quality of this riflescope (especially for the cost).
The test scope has 1/8 MOA adjustments and illuminated MOA-H reticle. The MOA-H has hash marks that subtend 2 MOA at 24X; therefore the hash marks are 1 MOA apart at 48X. Since this scope is so bright and clear, I tend to leave it at 48X for most of my shooting. During very bright conditions, the depth of field can be increased with an aperture ring that can be purchased from Sightron. The illuminated reticle has 11 brightness settings. The above picture displays a high brightness level. Personally, I don’t envision using illumination during my shooting sessions.
This reticle is a little “busy” for many shooters who use the scope at close range. But for longer range, it seems ideal for my old eyes. If you wish, you can order a 10-50X SVSS ED with a 1/10th-MOA target dot reticle, non-illuminated. You’ll save money with that more basic version, model #27008.
Competing with New Sightron Scope at 300 Yards
I shot the scope in its maiden match at 300 yards. Spotting my 6mm bullet holes was easy, even in Louisiana’s famous mirage. I shot the entire match at 48X. The scope tracked perfectly during the match and the 1/8 MOA adjustments were spot on. At this 48X power, the MOA hash marks serve as a great aid in determining how far one needs to adjust his aim. The set-up for the match is shown in the photo above. The scope performed excellent even in tough conditions — it was hot, windy, and mirage was very bad. Today really tested my ability to battle the conditions with this new scope. The sun was bright; the ground was wet; and the wind was blowing; and it was hot. I shot the four score targets with a 49/50, a 50/50, another 49, and finished with a 48.
What Things Could Be Better
What, if anything, are things I dislike about this scope? Most reviews that I have seen object to the 42-ounce weight, but with my benchrest rifle, this is not a problem for me. Another complaint that I have seen is the indicator line for the elevation turret. This scope has a Zero Stop and that stop obscures the indicator line. I added a line with a pencil and the problem is solved.
Tester Was So Impressed He Bought this Sightron SVSS ED
I have tested many premium scopes in the past and have chosen to purchase two of them after testing. This is one of the two I bought. If you are in the market for a $2000-$2500 (street price) scope that will compare favorably with $3500 scopes, this may be the one for you.
This is a quality scope in every way and there are few things with which to find fault. The reticle seems too busy for me, but many long range shooters use the tree-shaped series of dots that are 1 MOA apart at 48X and 2 MOA at 24X. Part of my problem is 76-year-old eyes that need cataract surgery. One cannot fault a scope for this problem.
I can recommend this scope for the long range shooter without reservation. If your type of shooting can tolerate the weight and the cost, I believe that you will find this scope to your liking. Good shooting — James Mock
Here is a European video review of the Sightron SVSS 10-50x60mm with ED Glass:
* There are TWO different Sightron SVSS 10-60X scopes. The basic model (#27008), non-illuminated without Zero Stop, can be found for under $2000, but typically retails for around $2300. As tested in this review, the Zero Stop Model with illuminated MOA-H Reticle (#27011) is about $2450 street price.
Share the post "James Mock Reviews Sightron SVSS ED 10-50x60mm Scope"
Gun guys are always shipping stuff around the country — whether it’s a barrel to be chambered, or a scope that needs to go back for warranty repair. Or maybe you’ve sold some bullets or reloading dies you no longer need. To ensure your precious packages get to their destination in one piece, it’s important to take precautions when boxing up your items. And by all means insure packages for full value — even if your packaging is perfect, there is always the possibility that your shipment might be lost altogether. Sadly, that can happen, no matter which carrier you choose: Fedex, UPS, or the U.S. Postal Service (USPS). Here are some tips for shipping gun stuff — we explain how to pack items properly and how to minimize the risk of loss.
Tips for Shippers
Dennis Haffner from McGowen Precision Barrels offers some advice on how to avoid damage when shipping gun parts or other valuable or heavy items. Dennis explains:
“First, I started double-packing the contents and in many cases double-boxing. I spend a fortune on heavy-reinforced shipping tape. If the contents are loosely packed, the package is going to get crushed. On real important items or delicate items, wrap the content in plastic and spray the inside void areas with non-expanding foam. They make shipping foam just for this. This method really works. Since I started paying more attention to packaging, I have just about wiped out my issues with all three companies (Fedex, UPS, USPS). Yes, I hate doing it, but in the long run for us, it’s cheaper.
Bullet shipments are the worst — a shipment of 500+ bullets can destroy a cardboard box. I have ordered bullets from individuals who put them in baggies and filled the remainder of the box with foam peanuts. That is not going to work. Any piece of metal, including a die, will puncture a cardboard box, or destroy a padded envelope. Just look at the tracking information and imagine your package bouncing around in the back of the shipping truck, probably under many other packages. My advice is to NEVER use padded envelopes. Barrel nuts or recoil lugs will most likely never make it.
ORM-D items are required to be shipped in heavily-reinforced, double-walled containers. The packages still get a little damage, but the contents usually survive.
How do shipments get damaged? Consider this — one of the shipping companies this year flipped (overturned) one of our new CNC machines (which rendered it useless). Maybe your small packages were in the same delivery truck as my CNC machine. I wonder how many little boxes were crushed underneath it.
As for USPS flat rate boxes — you would not believe what people try to stuff in these boxes. USPS finally put a weight limit on the boxes — they had to. I sometimes take my delicate items packed in an envelope or small box. I spray foam in a larger flat rate box and insert the smaller package, then fill the remainder of the void with foam. It works, and part usually arrives undamaged.”
Shipping Rifle Barrels (PVC Tube and Tennis Ball Method)
A new match-grade barrel can cost $350 or more, and it might take six months (or more) to replace it, given the current wait time with top barrel-makers. So, you don’t want your nice new tube to get damaged in transit. Forum Member Chuck L. (aka “M-61″) offers these tips for shipping rifle barrels:
“Packing a barrel can be a problem. Here’s a shipping method that won’t stop lost shipments but so far has stopped damage. Get a PVC pipe (of size appropriate to your barrel) with fitted caps for each end. Attach a cap to one end. Tape the barrel threads and tape over the muzzle. Then drop one standard tennis ball into the pipe. Place barrel in pipe. Next add whatever peanuts or foam you can jam in to support the barrel on the sides. Then place a second tennis ball into the opposite end of the PVC pipe. (So now you have a tennis ball on either end of your barrel.) With everything secure inside, attach the upper cap and tape it down securely. With this packing procedure, when the carrier launches the pipe like a javelin, at least the barrel will not come through like a spear and be gone. Label the pipe with very large address labels so no one suspects it’s just garbage laying around. This procedure may seem ridiculous but it has worked for me. Oh and definitely get insurance. If your item is insured, the shippers will look harder to find it.”
Editor’s Note: Fedex also makes a triangular-profile cardboard shipping box. This 38″ x 6″ x 6″ x 6″ Fedex Tube (designed for blueprints and posters) is free for the asking. For most barrels, there should be enough clearance to hold your PVC tube (with barrel packed inside tube). However, don’t ship the barrel inside the cardboard box by itself. Cap and pad the ends and bubble wrap it heavily, or better yet, use the PVC tube method described above, with the PVC tube inside the box.
The anvil is the tripod-shaped thin metal piece protruding above the bottom of the primer cup. Getting the primer sitting fully flush on the bottom of the case primer pocket, without crunching it too much, requires some keen feel for the progress of primer seating.
In two informative Midsouth Blog articles, Glen Zediker offers helpful advice on priming. First he examines what happens to the primer itself as it is seated in the cup. Glen explains why some “crush” is important, and why you never want to leave a high primer. Glen also reviews a variety of priming tools, including his favorite — the Forster Co-Ax Bench Primer Seater. Then he offers some key safety tips. Glen provides some “rock-solid” advice about the priming operation. You’ll find more great reloading tips in Glen’s newest book, Top-Grade Ammo, which we recommend.
Priming Precision vs. Speed
Glen writes: “The better priming tools have less leverage. That is so we can feel the progress of that relatively very small span of depth between start and finish. There is also a balance between precision and speed in tool choices, as there so often is.”
Benchtop Priming Tools — The Forster Co-Ax
Glen thinks that the best choice among priming options, considering both “feel” and productivity, may be the benchtop stand-alone priming stations: “They are faster than hand tools, and can be had with more or less leverage engineered into them. I like the one shown below the best because its feeding is reliable and its feel is more than good enough to do a ‘perfect’ primer seat. It’s the best balance I’ve found between speed and precision.”
Load Tuning and Primers
Glen cautions that you should always reduce your load when you switch to a new, not-yet-tested primer type: “The primer is, in my experience, the greatest variable that can change the performance of a load combination, which is mostly to say ‘pressure’. Never (never ever) switch primer brands without backing off the propellant charge and proving to yourself how far to take it back up, or to even back it off more. I back off one full grain of propellant [when I] try a different primer brand.”
Priming Safety Tips by Zediker
1. Get a good primer “flip” tray for use in filling the feeding magazine tubes associated with some systems. Make double-damn sure each primer is fed right side up (or down, depending on your perspective). A common cause of unintentional detonation is attempting to overfill a stuffed feeding tube magazine, so count and watch your progress.
2. Don’t attempt to seat a high primer more deeply on a finished round. The pressure needed to overcome the inertia to re-initiate movement may be enough to detonate it.
3. Don’t punch out a live primer! That can result in an impressive fright. To kill a primer, squirt or spray a little light oil into its open end. That renders the compound inert.
4. Keep the priming tool cup clean. That’s the little piece that the primer sits down into. Any little shard of brass can become a firing pin! It’s happened!
Gun guys are always shipping stuff around the country — whether it’s a barrel to be chambered, or a scope that needs to go back for warranty repair. Or maybe you’ve sold some bullets or reloading dies you no longer need. To ensure your precious packages get to their destination in one piece, it’s important to take precautions when boxing up your items. And by all means insure packages for full value — even if your packaging is perfect, there is always the possibility that your shipment might be lost altogether. Sadly, that can happen, no matter which carrier you choose: Fedex, UPS, or the U.S. Postal Service (USPS). Here are some tips for shipping gun stuff — we explain how to pack items properly and how to minimize the risk of loss.
“First, I started double-packing the contents and in many cases double-boxing. I spend a fortune on heavy-reinforced shipping tape. If the contents are loosely packed, the package is going to get crushed. On real important items or delicate items, wrap the content in plastic and spray the inside void areas with non-expanding foam. They make shipping foam just for this. This method really works. Since I started paying more attention to packaging, I have just about wiped out my issues with all three companies (Fedex, UPS, USPS). Yes, I hate doing it, but in the long run for us, it’s cheaper.
How do shipments get damaged? Consider this — one of the shipping companies this year flipped (overturned) one of our new CNC machines (which rendered it useless). Maybe your small packages were in the same delivery truck as my CNC machine. I wonder how many little boxes were crushed underneath it.
“Packing a barrel can be a problem. Here’s a shipping method that won’t stop lost shipments but so far has stopped damage. Get a PVC pipe (of size appropriate to your barrel) with fitted caps for each end. Attach a cap to one end. Tape the barrel threads and tape over the muzzle. Then drop one standard tennis ball into the pipe. Place barrel in pipe. Next add whatever peanuts or foam you can jam in to support the barrel on the sides. Then place a second tennis ball into the opposite end of the PVC pipe. (So now you have a tennis ball on either end of your barrel.) With everything secure inside, attach the upper cap and tape it down securely. With this packing procedure, when the carrier launches the pipe like a javelin, at least the barrel will not come through like a spear and be gone. Label the pipe with very large address labels so no one suspects it’s just garbage laying around. This procedure may seem ridiculous but it has worked for me. Oh and definitely get insurance. If your item is insured, the shippers will look harder to find it.”
