Can you form a wildcat cartridge such as the 6 Dasher without expending primer, powders, and bullets? Absolutely. Using the hydro-forming method you can form improved cases in your workshop with no firing whatsoever, so there is no wear on your precious barrel. Watch this video to see how it’s done:
6 Dasher Case Hydro-Forming Demonstration:
Forum member Wes J. (aka P1ZombieKiller) has produced a helpful video showing how to form Dasher cases use the Hornady Hydraulic forming die kit. This includes a two-part die (body and piston), and a special shell holder. To form the case, you insert a primer in your virgin brass, top the case off with with a fluid (water or alcohol), then run the case up into the Hydro-forming die. A few stout whacks with a hammer and your case is 95% formed.
This same procedure can be accomplished with a Whidden Gunworks 6mm Dasher hydraulic form die. We like the Whidden hydro-forming die for its production quality and consistent results. This Whidden system works great according to our Forum members.
Hydro-Forming Procedure Step-by-Step:
1. Insert spent primer in new 6mmBR brass case.
2. Fill with water or alcohol (Wes prefers alcohol).
3. Wipe excess fluid off case.
4. Place case in special Hornady shell-holder (no primer hole).
5. Run case up into Hydraulic forming die.
6. Smack top piston of forming die 3-4 times with rubber mallet or dead-blow hammer.
7. Inspect case, re-fill and repeat if necessary.
8. Drain alcohol (or water) into container.
9. Remove primer (and save for re-use).
10. Blow-dry formed case. Inspect and measure formed case.
Wes achieves very uniform cartridge OALs with this method. He measured ten (10) hydro-formed 6 Dasher cases and got these results: two @ 1.536″; 2 @ 1.537″; and 6 @ 1.538″.
Three or Four Whacks Produces a 95%-Formed Case
With a Whidden or Hornady hydro-forming die, hydraulic pressure does the job of blowing out the shoulders of your improved case. The process is relatively simple. Place a spent primer in the bottom of a new piece of brass. Fill the case with water, and then slip it into a special Hornady shell-holder with no hole in the middle. Then you run the case up into the forming die. Now comes the fun part. You gently insert a plunger (hydraulic ram) from the top, and give it three or four stiff whacks with a mallet (or better yet, a dead-blow hammer). Remove the plunger and you have a 95% formed case, ready to load.
Special Shell-Holder
Hornady supplies a shell holder made specifically for the hydro die; there’s no hole in the bottom of it. Just insert a spent primer into the primer pocket and you’re ready to go. The spent primer, combined with the solid shell holder, keeps the water from seeping out of the primer pocket. The primer pushes out a little bit during this process, but it’s impossible for it to come out because of the way the shell holder is designed. The shell holder has a grove which allows the case to slide out of the shell holder even when the primer protrudes a bit.
The 6mm Creedmoor has become one of the most popular cartridges for PRS/NRL competition, and it also works great in the varmint fields. Good Lapua 6mm Creedmoor brass is available, and there are many 6mm Creedmoor factory rifle options now, such as the Savage Model 110 Elite Precision with MDT chassis and the Ruger Precision 6mm Creedmoor with 26″ barrel.
Do-It-Yourself 6mm Creedmoor Rifle Project — UltimateReloader.com
Another smart, cost-effective option for 6mm Creedmoor fans is to build your own rifle, starting with a Howa barreled action. The Howa 1500 is a mag-fed, flat-bottomed bolt action that ships with the excellent HACT 2-stage trigger. Howa 1500 full-size barreled actions have been available with a variety of barrel lengths and contours, starting at $429.99 at Brownells. Howa 1500 Mini barreled actions are available starting at $399.99 at Brownells.
There are quite a few good stocks/chassis systems now offered for Howa 1500 actions, including the excellent KRG Bravo Chassis, which features an ergonomic composite outer shell over a precision-machined inner chassis.
Gavin Gear fitted a KRG enclosed fore-end and Mystic Precision MPOD to his 6mm Creedmoor rifle.
Our friend Gavin Gear of UltimateReloader.com has built a nice 6mm Creedmoor rifle using a Howa 1500 heavy-barreled action and KRG Bravo Chassis. This project has proven very successful. The rifle has shown impressive accuracy and outstanding reliability. Gavin has used this rifle in some practical/tactical competitions, and it did well.
In this video, Gavin fits KRG’s enclosed fore-end to the KRG Bravo chassis. This accessory fore-end features a top Picatinny rail and various attachment options on the sides and lower section. Here you can see the enclosed fore-end (upper right) next to the factory forend included with the KRG Bravo (lower left):
Gavin then fits a Mystic Precision MPod from EGW. This stable, wide-base bipod uses a T-Slot rail for rifle attachment, and has legs that adjust independently for height. The video shows the rifle coming together step-by-step. This is something the average guy can do with simple tools — no gunsmithing is required, because the Howa barreled action is pre-chambered for the 6mm Creedmoor cartridge.
In the video above Gavin unboxes his Howa 1500 barreled action from Brownells. He then mounts the barreled action to the KRG Bravo stock, checking the torque levels. Next Gavin borescopes the hammer-forged barrel (5:55) noting: “What I saw I liked — there are practically no tooling marks. The finish on the lands and grooves looks really good”. Lastly, Gavin tested the trigger with his TriggerScan TS-11 (6:24), confirming a two-stage pull weight of about 2.25 pounds out of the box.
BONUS: PRB 6mm Creedmoor and 6.5 Creedmoor Load Survey
The Precision Rifle Blog (PRB) has compiled Load Data from PRS Competitors, for both 6mm Creedmoor and 6.5 Creedmoor. For new 6mm Creedmoor shooters, this PRB study is a good place to start. PRB surveyed the match loads for “173 of the top-ranked precision rifle shooters in the country”. One cautionary note: These PRS guys may be loading fairly hot, so work up gradually, 0.3 grains at a time. CLICK HERE.
Sierra Bullets has published load data for the 6mm Creedmoor cartridge. Sierra has released very comprehensive 6mm Creedmoor load data in printable PDF format, covering fifteen (15) different bullets from 55 to 110 grains. NOTE: Hornady brass was used for Sierra’s 6mm Creedmoor load tests, not the superior, stronger Lapua 6mm Creedmoor brass with small primer pockets. Hand-loaders using Lapua brass may have to adjust their loads.
Here are Sierra’s 6mm Creedmoor Load Data Charts for 90-95 grain bullets plus the 107gr MK. There are six more tables for other bullet types on Sierra’s 6mm Creedmoor Load Data Page.
Many shooters prefer to deprime their brass before resizing. That way they can tumble cases or keep primer debris off their main press. To deprime cases before sizing or cleaning you can use a Decapping Die. This pushes out the spent primer without changing the neck or body of a case. Such decapping dies work fine, but they do require the use of a press. Here is a handy alternative — a cool tool that allows you to deprime brass anywhere — no press needed.
Handheld Primer Removal Tool From Frankford Arsenal
This cleverly-designed Hand Deprimer Tool allows you to deprime cartridge cases without a press. This hand-tool from Frankford Arsenal will deprime brass and capture primers conveniently. You can deprime your cases while watching TV or relaxing in your favorite chair.
This device lets you remove spent primers anywhere — no press needed and all the mess (cups/anvils/residue) stays in the capture chamber. This tool comes works with nearly all common case types up to .338 Lapua Magnum. With good leverage, this tool does the job quickly and efficiently. Forum members have praised this handy tool, but recommend wearing a thick glove if doing more than 100 cases in a session.
This handy depriming tool is very versatile. With a universal, cylinder-style cartridge-holder, the tool can deprime a wide variety of cartridge types from .20 caliber up to .338 caliber. Three different plastic collets are provided to handle for different diameter cases. Spent primers are captured in a removable spent primer catch tube. Simply twist off the clear catch tube to dump the spent primers. With die-cast metal construction, this tool should last through many thousands of depriming cycles. MSRP is $54.99. Right now it is $47.98 on Amazon with 82% 5-star ratings.
User Modifications — Grip Padding and High-Volume Capture
Many users recommended putting some kind of padding on the grip and front lever to reduce pressure on the fingers. This can be done with a wrap or a rubber covering. In addition, users have adapted the unit with an attached hose and large primer capture jug. If you depriming hundreds of cases at a time, this hose conversion may make sense.
Review from actual owner: “I have owned one of these for about eight years and deprimed over 10,000 cases with this tool. I have never had to replace a single part on it. You will have to adjust the return spring every so often, but that is a very easy task. If you are depriming a LOT of brass, the handle can tear up your hand a bit. Solution: Wear a Mechanics Glove. Easy Peasy! You will NOT regret this purchase.”
How to Adapt Tool for Small Flash Hole Brass
The Frankford Arsenal Deprimer Tool was designed for LARGE flash-hole brass. To deprime brass with small (1.5mm/0.59″) small flash-holes, as found on Lapua .220 Russian and 6mmBR cases, you will need to reduce the pin diameter. Frankford Arsenal currently recommends purchasing a replacement pin and “sanding it down” to the smaller diameter. NOTE: This is NOT difficult — simply spin the stock pin in some sandpaper.
The CMP National Matches at Camp Perry, Ohio kick off July 7, 2023 with smallbore events. The Camp Perry matches are historic, having been held since 1907 at this location on the shores of Lake Erie. The 2023 First Shot Ceremony takes place Monday, July 10, at 4:30 p.m. on the grounds of Camp Perry. Multi-time Nat’l High Power Champion SFC Brandon Green will speak and make the traditional First Shot to officially open the National Matches.
For this week’s Saturday at the Movies, we offer six videos from Camp Perry. These cover both rimfire and centerfire shooting, team matches (including the famous “Rattle Battle”), along with pistol shooting. If you’re heading to Camp Perry this summer, today’s video showcase provides an informative preview.
CMP National Matches at Camp Perry — 2023 Preview
This 3-minute video shows the Camp Perry ranges and shooting facilities and explains the programs scheduled for summer 2023, including training courses. The video also covers nearby accommodations and explains how to register for the National Matches on the CMP website.
NTIT Team Match — “Rattle Battle” at Camp Perry
The CMP’s National Trophy Infantry Team Match (NTIT) has been a staple at the National Matches since 1922. Also known as the “Rattle Battle,” the event is one of the most unique in the competitive rifling world — scoring is based on how many hits six-person teams can score on a bank of targets during a series of 50-second firing periods at four yardages.
Watch CMP ‘Rattle Battle’ Video — 50 Seconds of Rapid Fire…
Teams fire upon eight silhouette targets from 600, 500, 300 and 200 yards during successive 50-second periods. After each rapid-fire string, team members move forward (to the next-closest distance) carrying all equipment from firing line to firing line. The video shows the California Grizzlies, one of the top junior squads. The lead photo shows the U.S. Army Reserve (USAR) Team in action during the NTIT match. See more in USAR “Rattle Battle” Video.
Camp Perry M1 Garand Competition — Vintage Military Rifle
The John C. Garand match is a Camp Perry classic. Note the signature Garand clip in the air.
The CMP hosts the popular M1 Garand Match as well as the Springfield M1A Match. This writer’s father carried a Garand in WWII — reason enough for me to want one. But I also loved the look, feel, and heft of this classic American battle rifle. And the unique “Ping” of the ejected en-bloc clip is music to the ears of Garand fans. Some folks own an M1 Garand for the history, while others enjoy competing with this old war-horse. The CMP’s John C. Garand Match is one of the most popular events at Camp Perry every year. There are other vintage military rifle matches.
Rimfire Sporter Event Draws Hundreds of Competitors
If there is a single CMP event at Camp Perry every summer that offers the highest level of shooter satisfaction, the most diverse group of competitors, and the lowest cost of entry, that would have to be the annual Rimfire Sporter Match. This year’s match will be held on Saturday, July 8, 2023, during the first weekend of the National Match Schedule at Camp Perry. One of the most popular annual Camp Perry events, the Rimfire Sporter Rifle match features .22 LR competition in open sights (O-Class), telescopic (T-Class) and tactical/unlimited (TU) classes, fired at 25 and 50 yards. A CMP Rimfire Clinic will be held prior to the match.
Each year, the Rimfire Sporter Match attracts hundreds of shooters to the shore of Lake Erie at Camp Perry. The CMP National Rimfire Sporter Rifle Match offers shooters a recreation-oriented competition where they use affordable, smallbore sporter rifles with either scopes or iron sights. All you need are a .22 LR rifle, sling, and ammo.
Service Rifle Matches — AR-Platform Rifles, Now with Optics
Service Rifle shooting is fun yet challenging. You need to develop skills with multiple positions and be able to make rapid wind calls. However, the modern AR-based service rifle is affordable and has relatively low recoil. Highly-customizable, modern service rifles can be fitted with adjustable stocks and optional magnified optics. Older military rifles, such as the M1A and M1 Garand, offer different challenges with heavier-recoiling cartridges, greater weights, and classic iron sights. Hi-Lux asked competitors at Camp Perry during CMP’s 2021 summer games what they enjoyed most about competition with service rifles and Military rifles such as the M1 Garand. The shooters’ responses had four key themes: Self-Improvement, Comradery, History (enjoying shooting rifles with heritage), and Challenge.
Camp Perry Bullseye Pistol Competition
Camp Perry hosts the most prestigious annual trophy matches in our nation’s history. And in a venue renowned for service rifle matches, the sport of precision pistol is no less important, no less challenging, and no less respected. The National Trophy Pistol Matches are all about traditional handgunning — the stance, the intense concentration, and of course, the one-handed grip. It’s all unmistakable as the game of Bullseye Pistol. Every year there are 20+ match trophies for the top Bullseye Pistol shooters, both military and civilian. And the very best will claim National Match Trophies and receive the President’s 100 Tab.
CMP Camp Perry National Matches Registration Links
The 2023 CMP National Matches at Camp Perry commence Friday, July 7, 2023 with the Rimfire Sporter Clinic and Smallbore check-in/practice. The summer schedule concludes Saturday, August 5 with the Palma Match and awards. Here is the full CMP schedule (click to zoom):
NOTE: This CMP Calendar is hosted online in spreadsheet format. This allows you to increase display size, and also to search for specific words. CLICK HERE to view full spreadsheet calendar.
History of Camp Perry
“In the year 1907 the machinery of the National Matches, now grown to immense proportions, was moved to the mammoth new range at Camp Perry.”
—James Drain, Arms and the Man, August 1911
Federal legislation originally launched the National Matches. The 1903 legislation also established the National Matches, commissioned the National Trophy and provided funding to support the Matches. The National Matches have been held at Camp Perry since 1907. The range is located along the shores of Lake Erie in northern Ohio near Port Clinton. The site was first acquired in 1906, in response to the need for a larger facility for military training and the NRA’s shooting programs. The original land for Camp Perry was purchased in 1906, and the reservation was named after Commodore Oliver Hazard Perry, the American naval commander who won the Battle of Put-in-Bay during the War of 1812.
On August 19, 1907, Cpl. L. B. Jarrett fired the first shot at the new Camp Perry Training Site. And that year, 1907, Camp Perry held its first National Pistol and Rifle Championship events. This location has hosted the annual National Matches ever since. Typically over 4,000 competitors attend the National Matches each year, making it the most popular shooting competition in the western hemisphere.
If the battery on your safe’s electronic lock is more than a year old, or if it is not giving you the right voltage, replace it today!
Check Your Gun Safe Batteries
We’re halfway through 2023. Hey guys — when was the last time you replaced the batteries in your gun safe? Has it been more than a year? If so, it’s time you get a new battery (or two) for that safe. The electronic keypad won’t work with an insufficient charge, and the lock system could potentially lose its combination memory if you wait too long.
IMPORTANT: If you have a safe with an electronic keypad, you should replace the battery every year as a precautionary measure. Trust us, you don’t want to come back in a few months and find that the keypad memory is kaput, and you’re locked out. That can lead to frustration and an expensive locksmith visit.
Here’s a true story. I have one safe with a Sargent & Greenleaf (S&G) keypad. A couple years back, in early December, I went to get into the safe. I punched in the correct combination, but all I got was a rapid “beep, beep, beep, beep” after I finished the last combination entry. I tried again to ensure I entered the combination correctly (I did). But again, the locking system responded with multiple rapid beeps indicating something was wrong. And the safe would not open. Now I was worried….
I popped out the battery holder (which slides in from the bottom of the keypad housing on the door). I removed the battery and tested it with a volt-meter. The 12-month-old Duracell 9-volt battery only registered 6.1 volts.
Low voltage was the problem. I went down to the store and got a couple new 9V batteries. I tested the new batteries and both measured 9.4 volts output. I slipped one of the new 9V batteries into the keypad housing, punched in the combination and everything worked OK again. Eureka.
Most electronic locks for safes WILL “remember” the combination for a period of time even when the battery is low (and the keypad’s “brain” should retain the combination when you remove the battery for replacement). However, a dead battery, or extended periods of low voltage can give you problems. Don’t rely on wishful thinking…
The 44th Edition of the Blue Book of Gun Values is now on sale, for immediate delivery. Purchase this popular price guide through Blue Book Publications for $59.95. Or you can order from Amazon for $54.99 as well. The Blue Book of Gun Values by S.P. Fjestad is the leading gun valuation resource. There are now over 1.8 million copies in circulation worldwide. This book continues to be the “Bible” for buyers, sellers, collectors, and connoisseurs in the firearms industry.
Blue Book of Gun Values, 44th Edition, May 2023
The 44th Edition contains 2,528 pages covering over 1,800 manufacturers/trademarks, with over 35,000 gun model descriptions, and over 180,000 values, with new-for-2023 data!
Review by Tom Gresham, Gun Talk Radio Host
“At some point, every gun owner asks the question, ‘What’s it worth?’ The leading reference for decades has been the Blue Book of Gun Values. Whether you are a seller, a buyer, a shopper, or just curious, this constantly-updated gold mine of research is your friend.”
Features of the new Blue Book of Gun Values:
· Includes the new 2023 makes and models, with many new handguns and rifles, and important pricing updates.
· 2,528 pages covering over 1,800 manufacturers and trademarks, with over 35,000 gun model descriptions.
· 180,000+ up-to-date values are provided — most complete resource in print.
· Important pricing updates on major trademark current, antique, and discontinued models, including Colt, Winchester, Smith & Wesson, and Ruger.
· Color Photo Percentage Grading System (PPGS) makes firearms grading even easier and more accurate.
· More information, more values, more illustrations, and more history than any other gun price guide on the market.
Our nation’s birthday, the 4th of July, is just two weeks away. You can celebrate this special time by adding a Patriotic Stars and Stripes rifle or pistol to your collection. Legacy Sports offers a USA Flag series with red, white and blue graphics. From pistols to rifles, the USA Flag collection of handsomely Cerakoted firearms will stand out from the crowd.
The Howa flag collection includes the APC Chassis models (steel and carbon barrel versions), the Mini Action EXCL Lite, and the TSP X chassis rifle. The USA Flag APC carbon-wrapped barrel version is the latest model. For rimfire fans, the CITADEL Trakr .22 LR rifles are also available in the USA Flag and Grayscale options for both the semi-auto and bolt-action models.
Flag Collection Rifles
• Howa APC Flag Chassis with Carbon-Wrapped Barrel (NEW) – 6.5 Creedmoor / .308 Win
• Howa APC Flag Chassis Steel Barrel – 6.5 Creedmoor / .308 Win
• Howa Mini EXCL Lite – .223 Rem /6.5 Grendel / 7.62×39 / 6mm ARC / 350 Legend
• Howa TSP X Chassis Rifle – 6.5 Creedmoor / .308 Win
• Citadel Trakr – .22 LRs in Semi-Auto and Bolt-Action
CITADEL Flag Collection Pistols
• 1911 .45 ACP
• 1911 .380 AUTO
• CP9 9mm Series
Howa APC American Flag Version
The American Flag Edition of Howa’s APC rifle features USA flag-theme red, white, and blue Cerakote finish and 3-chamber muzzle brake. This special edition is available with a scope and rings and shipped in a hard case. See VIDEO of Stars and Stripes APC Rifle.
Howa TSP X Chassis Rifle
The Howa TSP X Chassis rifle has a Cerakoted T-6 Aluminum Chassis and excellent adjustable, 2-stage HACT trigger. This rifle comes with a sub-MOA guarantee and Lifetime Warranty. The flat black version is offered in four chamberings: 6.5 Creedmoor, 6.5 PRC, .308 Win, and 300 PRC.
Howa Sub-MOA Accuracy Guarantee
Howa rifles are guaranteed to deliver sub-MOA performance of 1 inch or less at 100 yards with premium factory ammunition. Guarantee is not transferable. All Howa rifles purchased in the U.S. on or after January 1, 2017 are covered by this offer.
CITADEL Flag Collection Handguns
The CITADEL USA flag pattern handgun collection includes the new 100% USA-made CITADEL CP9 9mm series, the popular CITADEL .45 ACP full-size 1911 (shown above) and the CITADEL 1911 Baby .380 Auto pistols. Cerakoted ammo cans in the USA Flag and Grayscale Flag versions are also available with the CITADEL handgun options.
PDF Product Catalog Available CLICK HERE to view full Howa/Citadel Product Catalog with all patriotic color options. The Citadel Trakr .22 LR Rimfires and Boss 25 shotgun are also available in the USA Flag and Grayscale options. Cerakoted ammo cans in the USA Flag and Grayscale Flag are available with the Citadel handguns.
In our Shooters’ Forum there is a popular photography thread. Along with some great nature and hunting images, you’ll find quality photos of handsome firearms. Among the many images were head-turning photos of some very impressive pistols belonging to Forum member Beiruty from Texas. He has some of the most handsome mag-fed handguns we’ve ever seen. Here are six of his favorite semi-auto pistols from his collection. Three of these handguns boast beautiful engraving.
FN Browning High Power Renaissance
This 9mm hand-engraved High Power with silver finish was made in Belgium in 1971:
NOTE: This is one of a near-matching pair of FN HP Renaissance pistols featured in the top photo.
Hämmerli .22 LR Model 208, Special Edition
This Special Edition, one of 500, marks 125 years of Hämmerli Sportwaffenfabrik (1863-1988):
The handsome grip is factory carved. This Model 208 pistol shipped in a fitted case, shown below.
Colt .45 ACP 1911 Commander
This 1975-vintage Colt Commander 1911 sports fully-engraved frame and slide:
Smith & Wesson .22 LR Model 41 Long Barrel
This target pistol features a 7-3/8″ barrel with factory compensator. Grip is custom:
Browning .22 LR Medalist Pistol
This handsome Browning Medalist, all factory standard, was made in Belgium in 1964:
The video below shows another Browning Medalist of the same design and relative vintage:
Stoeger Arms American Eagle Navy Model Luger
This stainless Stoeger Navy Model 6″ Luger Pistol is vintage 1978-1980:
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
This RCBS Rock Chucker Supreme Master Reloading Kit makes it easy to get started reloading — with everything you need into one package. The kit includes: RockChucker Supreme Master Reloading Press, Universal Case Loading Block, .17-.60 Debur Tool, M500 Mechanical Scale, Uniflow III Powder Measure, Hand Priming Tool, Hex Key Set, Case Lube Kit, Powder Funnel, and Speer Reloading Manual. Right now this kit is just $343.99, a 33% savings!
2. MidwayUSA — Vortex Optics Sale with 15% Savings
⏺ Major Savings plus 15% Discount Code: VTX060123
If you’re in the market for a new scope, spotting scope, or red dot sight, check out the Midway Vortex Optics Sale. A wide variety of optics products are on sale this week with a special 15% Off promotion. Hunters should check out the Fury HD5000 Rangefinding Binoculars. These are now $1499.99 — $500 off MSRP. NOTE: Along with the discounted list prices, on qualifying Vortex optics you get an additional 15% Off with Discount Code VTX060123.
3. EuroOptic — Sako S20 Close-out Sale, Save $400-$600
⏺ Save HUNDREDS on outstanding SAKO S20 rifles, multiple calibers
The SAKO S20 is a truly outstanding hunting rifle. It offers a smooth action, great trigger, excellent accuracy, and a convertible stock. Right now at EuroOptic.com you can save $400-$600 on a new SAKO S20 in a variety of popular chamberings. 15 different caliber/stock combinations are on sale, with discounts from $450-$600. Shown above are six notable deals, but there are many more. CLICK HERE to see all S20 Close-out offerings.
4. Locked & Loaded — SAR USA 9mm Pistol w/optic, $319.99
⏺ Accurate, 9mm pistol with installed Red Dot at great price
Here’s a quality 9mm pistol with a slide-mounted red dot sight for under $320 — a truly great deal. This SAR USA Mete 9mm pistol comes complete with a modern red dot sight fitted on the slide. This pistol features a Safari tan frame, black slide, and 17-round magazine. If you want to get started in IDPA or action pistol competition, this is a great option. The SAR pistol grip is very comfortable with good ergonomics — better than Glock in our opinion.
5. Graf & Sons — Caldwell Accumax Carbon Fiber Bipod Sale
⏺ Save up to 23% on carbon-legged bipods
Caldwell Accumax Carbon Fiber Bipods offer excellent performance for the price — and you can save 13% to 23% right now at Grafs.com. Caldwell’s Carbon Fiber Bipods feature quick-deployment carbon fiber legs with 90-degree forward or backward locking with spring-loaded buttons. The Premium Carbon Fiber Bipod also features an omni-directional ball mount for 360-degree panning, a lever lock handle for fast adjustments, and twist-lock leg length adjustments. Seven different Caldwell carbon bipods are on sale.
⏺ New advanced turret with wedges to hold multiple die diameters
The T-7 Adaptive Press is the result of collaboration between Creedmoor Sports and Redding. The Creedmoor Sports T-7 Adaptive Press combines the time-tested Redding T-7 turret press with the precision-machined, stainless steel Creedmoor Sports Adaptive Press Head. The T-7 Adaptive Press incorporates an innovative Wedge die insert system. This allow handloaders to use more robust 1-1/4″ dies as well as standard 7/8″ dies.
7. Amazon — Digital Micrometer, $39.99
⏺ Very good unit for the price, with nice, large display
Want to upgrade to a digital micrometer? The REXBETI Digital Micrometer is a very good value at $39.99. With accuracy to 0.0001″, this will provide ultra-precise measurements. The unit is easy to use and has a large, clear LCD display. This comes with a nice hard case for storage and protection. NOTE — this type of micrometer does NOT work for measuring case-wall thickness. You’ll need a ball micrometer for that task.
8. Palmetto SA — Leupold Binoculars and Harness Kit, $119.99
⏺ Save 40% now on Leupold Binoculars and Harness
Hunters and varminters need binoculars. A great option is the Leupold BX-1 Timberline 10×42 Binoculars with Go Afield Harness. Right now this combo is just $119.99, a 40% savings off the regular $199.99 price. But act soon — we expect this deal to expire soon. These Leupold binoculars offer solid reliability and quality glass in a lightweight package. This combo includes the excellent, adjustable GO Afield binocular harness, that will hold your binocs and other items securely all day long.
9. Amazon — Frankford Arsenal Brass Dryer, $54.49
⏺ Very good brass drying unit, now with a big discount
Do you wet-tumble your brass but hate drying it? For a fast and easy way to dry cartridge brass, we like the Frankford Arsenal Brass Dryer. The-top mounted fan and temperature adjustment of up to 160 degrees allows for quick drying of up to 1000 pieces of brass. There are 5 removable, internal trays. That makes it convenient to dry multiple types of brass at the same time.
10. Amazon — Walker’s Slim Electronic Muffs, From $39.99
⏺ These NRR23 muffs have earned excellent customer reviews
All shooters need quality ear protection — and electronic muffs are a good option. The Walker’s Slim Electronic Muffs, with 23 dB Noise Reduction Rating, offer excellent performance for the price. These ear muffs protect against hazardous noises, while still letting you hear range commands. These comfortable, low-profile design muffs have earned an 86% 5-star rating among buyers. A number of color options are offered, starting at $39.99. One recent buyer posted: “At this price point, these are as good as it gets. They do a great job at the gun range and allow you to still talk to people at a normal conversational level.”
Summer Solstice is just four days away. That means shooters nationwide will soon be dealing with peak summer ambient temperatures. When it’s hot outside your barrels will heat up even faster during use — and that’s not good for barrel longevity or consistency during long strings of fire. If you want a barrel to have maximum useful life you need to keep it from getting very hot. That’s why you should have a barrel cooler. There are many variations, but the most popular models blow cooling air through the bore. This can reduce barrel temps significantly in a relatively short period of time.
For this Saturday Movies feature, we’ve found 7 videos that review commercial barrel coolers or show how to build your own cooler with a hose, small electric fan, and modified case. There are a variety of barrel coolers on the market currently. Three of the most popular coolers are the yellow BarrelCool, $39.99 at MidwayUSA, the red Magnetospeed RifleKuhl, $56.89 on Amazon ($59.99 MSRP), and the black/yellow Chamber Chiller BA PRO, $80.40 on Amazon.
Barrel Coolers — Why You Should Use Them
This video explains why it’s vitally important to keep your barrel cool, particularly when running a suppressor. The host, a long-range shooting instructor, explains: “The best way to extend your barrel life [is using] barrel coolers. We have learned through decades of shooting that keeping the barrel cool and cooling it as fast as possible between relays and strings of fire will return meaningful results in the longevity of your rifle barrel. If you shoot suppressed like we do, this brings the level of importance up to a whole new level. Keeping it cool will keep it running at its best longer than you ever thought possible.” The barrel cooler featured in this video is $65.00 on the Wolf Precision website.
Barrel Cooler Comparison Tests — Four Options
Barrel coolers are vital accessories that let you get more shots downrange with less time waiting. In this excellent, comparison test video LongRangeOnly’s Ryan Furman shows which barrel coolers will remove the most heat with the rate of air flow comparison. Ryan also covers some basic differences and attributes of each unit tested and tests the units with temp gauges. Units tested are the BarrelCool, Magnetospeed RifleKuhl, the blue-bodied Original Barrel Cooler (6:48 time-mark), and a large Coleman rechargeable Quick-Pump (8:12 time-mark). The latter two units provided the most airflow when fitted with an appropriate hose.
Build Your Own Barrel Cooler — New and Improved
Popular YouTube host F-Class John was one of the pioneers in building very affordable, yet very effective do-it-yourself barrel coolers. John initially used a hose fitted to a battery-powered black Rechargeable Mini Air Pump. John then tapered a hose to fit a cartridge case for a perfect fit in the chamber. The case-head was cut off to better fit the hose for maximum airflow.
F-Class John later created an upgraded barrel cooling system using smaller, more compact pumps. He would charge these with a high-capacity battery pack (see above) and a USB charging cord. As shown in the video above, this Gen 2 system proved to be very effective. John notes: “Make sure you watch how long you the pump runs and don’t let it overheat”. One of these USB-port Mini Air Pumps is currently available on Amazon for $29.98, and there are similar compact pumps for a bit less.
Chamber Chiller BA Pro vs. Magnetospeed RifleKuhl
This video compares two compact barrel coolers, the red Magnetospeed RifleKuhl, $56.89 on Amazon and the yellow Chamber Chiller BA PRO, $80.40 on Amazon. Hear the tester’s conclusions starting at the 2:40 time-mark. The tester reports that both the RifleKuhl and the Chamber Chiller fit well in the chambers. The two units cooled down barrels pretty much identically in the field. Measured with a Kestrel, the RifleKuhl had a 12 mph flow vs. 11 mph flow for the Chamber Chiller (3:03 time-mark). The deciding factors for the tester (1:32 time-mark) were the superior battery life of the Chamber Chiller (with an extra USB battery attached) and the quietness of the Chamber Chiller.
Riflekühl Barrel Cooler by MagnetoSpeed
The MagnetoSpeed Riflekühl barrel cooler is designed to get barrel temperatures down to intended operating levels quickly. The turbocharger-inspired impeller is engineered to produce great airflow in a small package. Powered by a single CR123A Lithium battery (included), ambient air is forced through the extendable nozzle down the bore of the rifle. This is pretty efficient and can typically cool a barrel in under 8 minutes. The Riflekühl doubles as a chamber flag and features an exclusive built-in air filter to prevent dust and dirt from being blown into your rifle.
DIY Barrel Cooler Made with Mattress Inflator and Hose
An average gun-owner can build a good barrel cooler relatively easily with low-cost components. In this GunMart.TV video from the UK, the host showcases a very effective barrel cooler he crafted with an electric mattress inflator and a hose. The unit has good flow and can cool a barrel in a couple of minutes (3:10 time-mark). These components can be purchased for under $30.00. The tester purchased his cooler fan for $14.99 on Amazon (3:40 time-mark).
Thanks to Boyd Allen for help finding these videos.
Hydro-Forming Procedure Step-by-Step:Special Shell-Holder
Check Your Gun Safe Batteries
Flag Collection Rifles
