For a benchrest, F-Class, or ELR competitor, the optic may easily be the most expensive component of the rifle. Even a hunter may spend as much on glass as he/she does on the rifle itself. Because scopes represent such a big investment, it is important to do some research before deciding what to buy.
Unfortunately, it is pretty much impossible to “test drive” a half-dozen or more optics. Thankfully, there are some video reviews on the internet that are, for the most part, helpful. Here we provide five scope comparison tests, with different price points, high to low.
1. Nine Long Range Scopes Compared by Pew Pew Tactical
Pew Pew Tactical (PPT) published lengthy comparison of nine long range scopes. For each model PPT examined clarity, eye relief, reticle design, parallax, and windage/elevation travel. PPT also provides short videos for all the scopes showing the operation of the controls. FULL PPT REVIEW HERE.
NINE Long Range Scopes Compared
1. Vortex Strike Eagle 4-24×50mm
2. Vortex Viper PST II 5-25×50mm
3. Leupold VX3i LRP 8.5-25×50mm
4. Leupold Mark 5HD 5-25×56mm
5. Burris XTR II 5-25×50mm
This 5-scope comparison test by Armslist Media yielded some surprises. All the scopes in the review retailed for $1500 or less. Most offer 5X at the low end and 20X or 25X at the high end. Three provide a four times zoom ratio, while the SIG Whiskey5 has a five times ratio and the Leupold VX6 has a full six times zoom ratio, with its 3-18X lens. That’s good for varmint hunters who often scan a wide field of view and then zoom in on a critter to make the shot. We think all these scopes offer good value for the money. We add that anyone considering these optics should also look at the Zeiss V4 line which offers outstanding glass at very competitive prices. The Zeiss Conquest V4 6-24x50mm is just $1199.00 at EuroOptic. The Zeiss V4 would be one of our first choices for a SFP varmint scope, no doubt about it.
4. Trijicon TR23 5-20×50mm
5. SIG Sauer Whiskey5 5-25x50mm
3. Five Sub-$1000 Scopes Reviewed by Precision Rifle Network
If you are looking for a moderate-priced optic for a PRS or hunting rifle, consider one of the scopes featured in this comparison review. These all offer 24-25 powder at the high end, plenty of magnification for PRS/NRL matches. This video compares the controls of all five optics, and there are through-the-lens views showing the reticles on each optic. The tester criticized the SIG Tango for “scope shadow” in view, and overly complex labeling on the knobs. He liked the Burris XTR2 saying it “is a well-respected optic in the precision rifle community … it is basically ‘bomb-proof'”, but he felt that Burris glass color fidelity was not on a par with the Vortex or Nightforce. (7:58). NOTE: the Nikon Black FX1000 series has been discontinued so these optics are available now at very attractive prices. Even before the price cut, the reviewer said “Guys, for the money, I’m not sure there’s another scope on the market that can compete with this thing.” (7:12). The 4-16x50mm FX1000 is just $649.99 at EuroOptic.com — a steal. We’ve used the 5-25x50mm FX1000 scope reviewed in this video — it has truly excellent glass, albeit stiff knobs.
FIVE $1000 Scopes Compared
1. Burris XTR2 5-25×50mm
2. Nightforce SHV 4.514x50mm
e. Nikon Black FX1000 6-24×50mm
.22 Plinkster is an honest tester who shoots thousands of rimfire rounds every year. So he’s in a good position to review budget-priced scopes designed for rimfire rifles. Because rimfire rifles have a different kind of recoil pulse than centerfire rigs, and because rimfire rifles are often shot rapid fire at plates, with hundreds of rounds fired in an afternoon, you want to find a scope that has been thoroughly tested to ensure long-term durability. Among the dozen scopes he tested, .22 Plinkster favored the Bushnell Rimfire Series: “I’ve used these [Rimfire Series] scopes a lot. These scopes, for the price point… you can’t go wrong.” He also recommended the Vortex Crossfire scope, noting that it had very clear glass and a rock-solid, transferrable lifetime warranty: “Vortex is one of my favorite scope to use, and as a company they really stand behind their products.”
5. Budget Optics for AR-Platform and Defensive Rifles
AR-platform rifles used for 3-Gun matches and home defense purposes don’t need high-magnification optics. Instead you want something that allows rapid target acquisition and has illumination for low-light situations. This video covers three budget-priced AR optics, two one-power Red Dots, and a Primary Arms 1-6x24mm SLx ACSS scope, which is offered in both SFP and FFP versions starting at $389.99 (not $289.99 as stated in video). A similar illuminated scope (with a better warranty), is the Vortex 1-6x24mm Strike Eagle, currently $299.99 on Amazon with BDC3 reticle.
The U.S. Military has a new machine gun and a new rifle in a new caliber. SIG Sauer has confirmed the final delivery of the Next Generation Squad Weapons (NGSW) systems to the U.S. Army, consisting of new 6.8x51mm Hybrid ammunition, the NGSW-AR lightweight belt-fed machine gun, the SIG NGSW-R rifle, and SIG suppressors. Ron Cohen, SIG Sauer President/CEO stated that work with U.S. soldiers has “led to rapid advancements over the current weapons systems and resulted in our delivery of the most innovative Next Generation Squad Weapons system to the U.S. Army.”
The new systems will shoot 6.8×51 Hybrid ammunition — a lightweight cartridge designed to handle higher pressures resulting in increased velocity and terminal performance. In civilian form, SIG Sauer calls this cartridge the 277 SIG FURY. The 277 SIG Fury and the military 6.8x51mm cartridges feature a conventional brass upper case body with a steel alloy bottom, case-head section. The hybrid design allows the ammo to run at significantly higher pressures than conventional ammunition. SIG Sauer states that “despite its revolutionary design, [this] hybrid ammunition can be manufactured on a widespread basis immediately.”
The SIG Sauer 6.8mm hybrid ammunition is designed for increased penetration at greater distances. Cohen continued, “using patent-pending technology the SIG Sauer Ammunition Division has engineered a completely new cartridge resulting in a more compact round, with increased velocity and accuracy, while delivering a substantial reduction in the weight of the ammunition.”
This video shows gun features and includes firing sequences with thermal cameras (1:50 time).
The new 6.8x51mm Hybrid ammo gives the new guns significant advantages: “The SIG Sauer Lightweight Belt-Fed Machine Gun (NGSW-AR) doubles the effective range and is 40% lighter than the current M249 while maintaining the preferred belt-fed operation, with reduced felt recoil to increase accuracy. The SIG SAUER Rifle (NGSW-R) is built on the foundation of the battle tested MCX platform with the added firepower of the 6.8×51 round; both the NGSW-AR and NGSW-R feature familiar AR-style ambidextrous ergonomics designed for a seamless transition from the legacy weapons to the SIG NGSW system.”
SIG SAUER Lightweight Machine Gun (NGSW-AR)
The SIG Sauer NGSW-AR is a light-weight (under 15-lb.), medium-caliber machine gun chambered for 6.8x51mm Hybrid ammunition. SIG Sauer designed the NGSW-AR to be 40% lighter than current systems, and dramatically reduce felt recoil while maintaining traditional belt-fed operation to increase downrange capability. This 6.8mm machine gun features ambidextrous AR-style ergonomics, quick detach magazines, increased M1913 rail space for optics, folding buttstock, and quick-detach suppressor. SIG Sauer claim this NGSW-AR “vastly improves upon the operation and function of the legacy M249.”
SIG SAUER Rifle (NGSW-R):
The NGSW-R lightweight rifle (aka MCX-Spear) is derived from existing SIG military rifles with the added firepower of the 6.8mm round. Features include a fully collapsible and folding stock, rear and side charging handle, free-floating reinforced M-LOK™ handguard, fully ambidextrous controls, and quick-detach suppressor.
277 SIG FURY (6.8x51mm) from SIG Sauer
The 6.8x51mm cartridge will be offered by SIG Sauer in a civilian version called the 277 SIG FURY. This boasts a SAAMI maximum average pressure of 80,000 psi, driving a 135-grain bullet to 3,000+ fps. That 80K PSI pressure is WAY higher than almost all other cartridge types. To achieve these high pressures, the 277 FURY uses a hybrid case with a brass body and harder alloy metal case head. This design allows the cartridge to run very high pressures. Dan Horner of SIG Sauer told us: “When the handloaders get hold of this brass, it will be a game-changer for sure”. We envision this cartridge could be necked down to 6.5 mm and it would dramatically out-perform the 6.5 Creedmoor. And yes the official name of the cartridge is all caps “277 SIG FURY”.
This story is about the purchase of a super-sized spotting scope with a notable history. Forum member David Buffington explains how he located a rare Unertl 100mm-objective spotter that had served Team USA in international competitions.
It is a rare pleasure to acquire a gun with a history. It is simply extraordinary to acquire a scope – in this case, a spotting scope – that has quite literally seen some of the best shots ever taken. The scope is an Unertl Team Spotting Scope, a beast of a 100mm scope especially made for long-range shooting matches. (For technical details, see: http://unertl.alexweb.net/100team.htm.)
And recently, I was pleased and proud to become its custodian …
In the AccurateShooter Forum Classifieds my friend, dgeesaman, found an ad for an Unertl “Team” spotting scope, a 100mm beast built by the famed Unertl company specifically for long range shooting spotting. I had tried to find one years earlier, but I had no luck. This time I struck gold. The Unertl Team was being sold by an accomplished shooter, Mike Dunia, and was in excellent condition complete with all the goodies, including the monster travel case you see above.
Now, because of its sheer size – about 60 pounds with the case – this scope is definitely NOT practical for casual spotting, but the image, well, it’s like being there. The image is extremely bright and sharp edge-to-edge with no hint of chromatic aberration. And once you get the beast to where you want to be, setup is remarkably simple, with a tripod, mount and scope all beautifully machined to move smoothly and easily.
Vintage Unertl optics can be purchased from Dewayne (Dewy) Greiner in MN, Classic Unertl Scopes.
The scope was sold to me by Mike Dunia, an accomplished marksman who served with the U.S. Army Marksmanship Unit and represented San Francisco’s famed Olympic Club in competitions around the world, for example, winning the British Columbia Target Rifle Championship in 2002 and the California Palma Championship in 2003. Dunia has had a notable 50+ year shooting career, starting in college when Dunia was Captain of the Stanford University Rifle Team. The scope was owned by Dunia’s friend, Larry Wilkins, who also served in the U.S. Army, was also an accomplished marksman, and also represented San Francisco’s famed Olympic Club.
Below is a photo of the USA Palma Team in 1995 with multiple Unertl 100mm spotting scopes:
The names of the individuals in this 1995 photo were provided by tool-maker Alan Warner, who was there that day many years ago. In the same Shooters’ Forum thread, Alan posted: “Far left, white shirt and hat, squatting is Burt Rallins. Prone — close left with small scope is me, Alan Warner. Standing in team jacket is Ken Erdman. Next in background is Mike Dunia. The Coach, sitting, is Bob Jensen. The Next coach is Eric St. John. Can’t make out the other coach or shooters. Last coach is Bill Meek.”
Here is just a bit of the vaunted history of the San Francisco Olympic Club (click photo to read full screen):
Although I do plan to use the scope, I feel an obligation to preserve as much of its history as I can, including, most importantly, the stories of the shooters who used it before it came to me. I should also mention that Wilkins served with the famous “Task Force Smith” at the start of the Korean War. If you’re not familiar with that horrific story of courage, do look it up.
Unertl Spotting Scope Original Cost … And in Current Dollars
What might this line of 100mm monsters have cost back in the day? Well, I’ve tracked down an Unertl price list from sometime after 1963 — we know that because it has a ZIP code in the address — and the price then was listed as $450, but another price list, dated 1994, puts the price at $2,200.
Of course, that’s $2,200 in 1994 dollars. That would be $3,842 in today’s 2021 money, according to USinflationcalculator.com. So the seven Unertl Team scopes seen here would cost $26,894 at present! — David Buffington
100mm Spotting Scope Operation
Were these scopes used to see bullet holes? Actually that was not their primary purpose. Shot locations on target were shown by shot markers placed by pit workers. But the scopes did serve important purposes, as explained by Forum member Dave Marshall: “You won’t be able to see any bullet holes past 300-400 yards with those scopes. They usually used a fixed 24X eyepiece. I don’t think there is a scope in existence today that can see bullet holes at 1000 yards. [It is possible — but only under very rare, perfect conditions. That said, spotting scopes ARE used all the time to see 1000-yard shot markers and thereby record scores. — Editor]
The main reason those scopes were used [in addition to seeing shot markers] was for better ability to read mirage and the larger objective made it possible to see bullet trace at longer ranges. Once the trace leaves the field of view due to steep trajectory, you can’t see it when it comes back down into the field of view.”
Description of Unertl 100mm Team Spotting Scope by Classic Unertl Scopes
The Unertl 100mm Spotting Scope is a large instrument which was designed to meet the requirements of team coaches to enable critical spotting of long range big bore matches. The coated prismatic optical systems, with a 100mm aperture objective and four element orthoscopic oculars is critically tested and hand-corrected so that the final system will yield matchless resolution. The objective cell has a sunshade which can be extended about 5″ when required and the eyepiece is screw focusing with a fast over-running push-pull travel. Dust covers are provided for each end. Workmanship is of the highest quality and the majority of the instrument is made from aluminum alloy and finished in a light gray wrinkle. The yoke mounting enables easy insertions and removal of the telescope from the yoke and tripod. By tensioning the binding screws the scope can be fixed by locked in position or so set to per-mit scanning of a series of targets. The lower portion of the yoke fits the cylindrical column of a floating action metal tripod. Within the tripod ram is a helical spring which counter-balances the scope and it can be raised or lowered with ease. A wooden carrying case of substantial construction houses the telescope, yoke, tripod and extra interchangeable eyepieces. Standard oculars are 6X, 24X. and 32X.
Above: FN’s new 509 LS Edge is a 9mm Long Slide “factory custom” with Low-Profile Optics-Mounting System, slotted slide, and 5″ hammer-forged target-crown barrel.
In the latest February 2021 edition of Shooting Industry Magazine you’ll find Part III of the publication’s 2021 New Product Showcase. This latest installment of SI’s features over 40 new products, all presented with photos and product details.
If you missed the previous showcases, visit ShootingIndustry.com to see the December 2020 and January 2021 issues or click the links above. Across all three editions, hundreds of products from more than 120 companies were featured in Shooting Industry’s 2021 New Product Showcase.
From the Shooting Industry Part III Showcase, we present four notable handguns:
1. Colt Mfg. and Davidson’s — Engraved 6″ Stainless Python
Davidson’s has collaborated with Colt’s Manufacturing on a special edition Colt Python revolver. Automated Finishing has created a deluxe engraved version of Colt’s new 6″ barreled stainless Python. The engraving is armory-grade cut and encompasses the barrel, full underlug, frame and backstrap. The top of the rib is left matte stainless to cut glare while sighting. The special Python is chambered in .357 Magnum, and has a walnut grip, red-ramp front sight and adjustable rear sight.
2. Volquartsen Black Mamba-X .22 LR Pistol
The Black Mamba-X .22 LR Pistol from Volquartsen features a LLV-4X upper with multiple mounting locations allowing for red dot sights. The pistol has a 1/2×28 threaded stainless steel 4.5″ barrel with stainless steel laser-hardened breech in a type III hard-anodized aluminum shroud. Additional features include the Volquartsen Accurizing Kit for a 2.25-lb trigger pull, DLC coated Volquartsen Competition Bolt and Volquartsen Single-Port Compensator. The LLV-4X Upper will be available as a stand-alone product and is compatible with both the Volquartsen Competition Bolt as well as the Ruger MK IV factory bolt.
3. Heckler & Koch VP9L 9mm Pistol
Combining optics-ready features for competition use, the Heckler & Koch (HK) 9mm VP9L OR (Optics Ready) is based on the popular VP9 platform. HK supplies an O-Ring bushing on the longer 5″ barrel to tighten the lockup, aiding accuracy. This ships with 20-round magazines provide additional rounds for longer stages. A machined slot in the slide accommodates most popular red dot pistol sights with one of 5 available mounting plates (sold separately).
MasterPiece Arms now offers the Freedom Gunworks double-stack 1911 pistol line. The handsome 9mm DS9 Hybrid Pistol shown above is machined from barstock and billet. It boasts an FGW slide serrations with slide lightening cut, Koenig hammer/sear, with a 2-lb. trigger pull. Notably, Each FGW pistol is hand-built, including lapping the slide/frame interface, and comes in a custom MPA single pistol case with one MPA 140mm magazine. A variety of configurations are available, including iron sights or optics-ready models.
Retro is back — at least in the CMP’s Standard Modern Military Rifle AR class. Though Service Rifle competition has evolved to allow optics and heavy barrel profiles, the Standard Modern Military Rifle (AR category) is truly a “blast from the past”. Overall weight is limited to 7.5 pounds, and the rifle must be equipped with iron sights (Rule 5.2.3). In addition, the rifle “be based on the M-16 rifle or be based on an AR design” with “exterior configuration similar [to] the original military or military-type rifle”. See Rules.
With this in mind our friend Dennis Santiago recently put together his own AR-platform Standard Modern Military Rifle for matches run under CMP Competition Rules. This is not quite a classic AR, as it has a metal free-float handguard (vs. plastic handguards), but it IS light (7.3 pounds), and it does have iron sights — a key requirement for Standard Modern Military class rifles.
Here is Santiago’s CMP Modern Military Rifle (Standard Class) with an ultralight free float tube that has a titanium barrel nut, and mechanical, center-able front sight. The barrel is an AR-Stoner brand 20″-long 1:7″ Government contour chambered in 5.56×45 NATO. Dennis says: “This makes the 7.5-lb weight limit with a few ounces to spare. We’ll see how well it drives soon enough.”
Dennis explains: “The Standard Modern Military (AR) is a category of military-style rifle that shoots the 200-yard, 30- or 50-shot courses alongside the M1 Garands, Springfields, Vintage, and M1 Carbines. This one boasts a Midwest Industries (MI) ultralight Free-float Handguard and a Yankee Hill folding front sight. Any Government contour or thinner profile rifle-length gas tube barrel with a 0.750″ gas block will work.” Colt makes a suitable Government Contour 20″-long, 1:7″-twist barrel, sold by MidwayUSA.
To test the accuracy of his rifle, Dennis fitted a Mantis-X unit on the top of the float tube. The Mantis-X records the movement of the rifle to interpolate shot placements. Dennis reports: “I spent some extra time at the range grabbing a decent zero for my Modern Military rifle. I stuck a Mantis-X on it to record a few shots shooting offhand at the plates at 200 yards. It drives very easily even with no shooting coat or glove.” The Mantis-X is attached just forward of the carry handle, on top of the MI free-float handguard. The Mantis-X works with live fire as well as dry fire. It communicates via BlueTooth to a smartphone App.
Rifle Shoots Well with 77gr Sierra MatchKings
The gun is presently zeroed with 77gr Sierra MatchKing ammunition. Dennis reports his rifle “can easily hold the X-Ring on an SR target for both 100-yard and 200-yard CMP Modern Military Games matches. And it’s fun to shoot!”
CMP Standard Modern Military Rifle (AR Class)
This rifle is built from carefully selected and fitted parts to conform to the CMP’s 7.5-pound weight limit iron-sighted rifle rule. Officially, this is a CMP Standard Modern Military Rifle, Class “A” (AR type).
1. S&W M&P lower receiver
2. White Oak Armament match upper receiver with 1/4×1/4-MOA pinned rear sights
3. AR-Stoner 20″ 1:7″-twist 5.56x45mm NATO Government contour barrel from MidwayUSA*
4. MidWest Industries ultralight free-float handguard with a Titanium barrel nut
5. Yankee Hill Machine folding front sight with a 0.072″ square front pin
6. RRA 2-stage trigger
7. A2 length buttstock
Easy Rifle Build Using Mostly Existing AR Parts, Plus New Barrel and Free-Float Handguard
Dennis was able to put his Modern Military AR together using components he had collected over the years: “Most of these parts were already in my bin of old AR parts available to be recycled. The barrel and free-float handguard were the only new acquisitions.” And with the AR’s modular format, this was an easy build: “Assembly time was about 30 minutes. I’ve done these parts swaps so many times now.”
Key Rules for Standard Modern Military Rifle (AR Type)
Dennis Santiago’s new AR rifle was built as a “Standard U.S. Modern Military Rifle”, Class A (AR Type), as specified in the CMP Competition Rules.
5.2.3 Standard U.S. Modern Military Rifles, Class A
Category A Standard Modern Military Rifles must comply with these requirements:
a) Rifles must be based on the M-16 rifle or be based on an AR design;
b) Rifles must be manufactured by a USA manufacturer;
c) Rifles must be equipped with issue-type metallic front and rear sights; rear sights with adjustments finer than one minute of angle are permitted;
d) Total rifle weight, with sights and without sling, may not exceed 7.5 pounds;
e) Rifles may be fitted with a float tube or free-floating handguard. A nonadjustable sling swivel may be attached to the forward end of the handguard; and…
f) The rifle must be chambered for the 5.56x45mm or .223 Remington cartridge.
Also, from Rule 5.2.2:
a) The exterior configuration of the rifle must be the similar to that of the
original military or military-type rifle;
b) The trigger pull may not be less than 4.5 lbs.;
Comments from other Modern Military Rifle Shooters:
“I built a Modern Military [Standard]. It was tough getting below the 7.5-lb [limit]. I had to carve off a bunch of the 20″ barrel diameter but wanted to stay with it for sight radius (over a 16″). I would just as soon shoot that little iron-sighted rifle at 200 yards as my 15-lb Nightforce-scoped Service Rifle. I love that little rifle.” — Kenneth S.
“I’m building one of these that will make 7.5-lb [Standard Modern Military] weight limit, with the long barrel and long sight radius. This has been on my list this winter.” — Tom K.
“We found that turning down a National Match barrel and taking a few inches off of it made a very accurate rifle.” — Jack A.
“My old (complete) A2 upper has been sitting forlorn on a shelf for a couple of years now. Perhaps I need to do a [Standard Modern Military] build of my own.” — Derek D.
Dennis Santiago replied: “Derek — that’s the reason I was attracted to this. I had bought a brand new WOA A2 pin upper receiver to make a new upper then the scope rule was adopted and it was all flat tops. This gives new purpose to the old parts.”
CMP Rules Defining Modern Military Rifles
Standard vs. Unlimited, Class A vs. Class B
There are actually two different classes of Standard Modern Military Rifles, Class A for AR-type rifles and Class B for other military-style rifles, such as the M1A and FN-FAL. Ok, got that? Now, in addition, there is also a second division for UNLIMITED Modern Military Rifles, again with two classes (Class A — AR-type and Class B — other military rifles). These unlimited rifles can have optics, heavier weights, modern-design adjustable-length stocks, and other upgrades. Here is Rule 5.2.2 from the current CMP Games Rifle and Pistol Competition Rules:
Every month, GunGenius.com publishes a Top Selling Report. This reveals the Best Selling Guns for each category of firearms sold on GunBroker.com. This culminates in a GunGenius year-end report on the Top Selling Firearms of the Year in a dozen categories, both new and used. As a special Feature, GunGenius now offers the “Top 20 of 2020″ for each category.
Here are the top-selling handguns for the year 2020, with the Top 20 Semi-auto pistols and Top 20 Revolvers listed separately (all first-time sale, not used). Visit the GunGenius Top 20 Page for more details.
Top 20 Handguns for 2020 (Semi-Auto Pistols and Revolvers)
Buying a Handgun? See What Others Choose
Looking to acquire a handgun for personal protection of home and family? There are countless options on the market. Your buying decision may be simplified by seeing what other consumers have chosen, as revealed by nationwide sales trends. You can check firearms sales figures using “Gun Genius”, a new data-crunching service of Gunbroker.com. On GunGenius.com you can select any type of firearm (handgun, rifle, shotgun) and see the top sellers for that category.
Along with pistols and revolvers as shown above, there are separate categories for: semi-auto rifles, bolt-action rifles, lever-action rifles, single-shot rifles, pump rifles, semi-auto shotguns, pump shotguns, over-and-under shotguns and more. You can also filter for sales trends (upwards and downwards). Drill down to see detailed product specifications and current prices.
Hot News! We just learned that Frankford Arsenal will offer two new reloading presses this year. It may be a while before these two presses arrive on dealers’ shelves but we wanted to give you a preview. Both presses are impressive. The new FX-10 is a TEN-station, auto-indexing progessive press. It will sell for $699.99, what you might pay for a different brand progressive with fewer stations and more limited capabilities. This FX-10 press offers a smooth, gear-driven shellplate, plus dual decapping stations and primer pocket swaging capability. There are optional (extra cost) bullet and case feeders. The press even offers a built-in LED light.
The F-1 is a robust single-stage press offering power, easy (open front) case access, and smooth cycling. The F-1 boasts a linear ball bearing system for smooth operation, an integrated LED light, a fully-contained primer catch system, and precision-machined solid steel construction.
Frankford Arsenal FX-10 Progressive Press
10-Station, Auto-Indexing
Manufacturer’s Product Description:
The Frankford Arsenal FX-10 is a 10-station automatic indexing reloading press purpose-built from the ground up to be the ultimate progressive reloading press. At its core, the FX-10 features rigid steel construction, multiple ball bearings, and a proprietary 10-station, gear-driven, rotating shell plate which all combine to virtually eliminate powder spillage and bullet tipping.
The FX-10 offers innovative improvements like dual de-capping stations to prevent primer drawback, in-line primer pocket swaging capability (for both small and large primers), and the ability to run powder check and case trimming dies. The FX-10 includes a case-actuated powder measure with a positive reset that guarantees you’ll never have to worry about squib loads resulting from a sticking powder measure. When it’s time to swap calibers, the FX-10’s innovative design allows the user the ability to quickly and easily swap-out tool heads and shell plates to reload anything from 9mm to 30-06 Springfield length cartridges. The FX-10 goes further and offers refined details like a roller handle, integrated LED light, and spring-loaded case locator buttons, which allow easy one-handed case feeding and lever operation, making the FX-10 exceptionally smooth and easy to operate. Compatible with our Frankford Arsenal Case Feeder and Bullet Feeder (sold separately), the FX-10 is the ultimate solution for progressive reloading. MSRP for the FX-10 is $699.99.
FRANKFORD ARSENAL FX-10 PROGRESSIVE PRESS FEATURES
OPTIONAL CASE AND BULLET FEEDER
CASE-ACTIVATED POWDER MEASURE
INTEGRATED BEARINGS FOR SMOOTH OPERATION
IN-LINE PRIMER POCKET SWAGING
SPRING-LOADED CASE LOCATOR BUTTONS
LOADS CARTRIDGES UP TO .30-06 SPRG LENGTH
SHELL PLATES FOR POPULAR CALIBERS
Frankford Arsenal F-1 Single-Stage Press
Manufacturer’s Product Description:
The Frankford Arsenal F-1 Single Stage Press is packed with innovative features to help you reload precisely and quickly so you spend less time reloading and more time on the range. At its core, the F-1 features a linear ball bearing system for smooth operation, an integrated LED light, a fully contained primer catch system, and precision-machined solid steel construction. Compatible with standard 7/8″x14 dies, this press will load up to .338 Lapua Magnum size cartridges. MSRP for the F-1 is $149.99.
FRANKFORD ARSENAL F-1 PRESS FEATURES
RAM RIDES IN BALL BEARINGS FOR SMOOTH OPERATION
LOADS UP TO .338 LAPUA Magnum LENGTH CARTRIDGES
INTEGRATED LED LIGHT
COMPATIBLE WITH STANDARD 7/8″ x 14 DIES
USES STANDARD SHELL HOLDERS
NO-MESS PRIMER CATCH USES BOTTLE OR HOSE
SELECTABLE CAM-OVER OR STOP OPERATION
SOLID STEEL ROD FRAME PILLARS
Credit EdLongRange for Frankford Arsenal New Product Tips.
Although the 2021 SHOT Show was cancelled, you can find many new-for-2021 products online. The NRA’s Shooting Illustrated website has put together a collection of 28 new products including rifles, pistols, shotguns, optics, safety gear and more — all from top manufacturers. Some of the features include test videos, such as a report on a S&W M&P fitted with the new Leupold DeltaPoint Micro red dot optic.
The Shooting Illustrated article reviews 28 products total. Here are two rifles, two pistols, and one shotgun featured in Shooting Illustrated’s New Products Showcase:
Winchester Wildcat .22 LR SR, Suppressor-Ready Model
Winchester has introduced a Wildcat SR, a suppressor-ready version of its popuplar Wildcat 22 semi-auto .22 LR rifle. This new Wildcat SR comes with a 16.5″ barrel threaded 1/2-28 TPI at the muzzle (with muzzle cap). This will allow the Wildcat SR to fit most rimfire suppressors as well as many muzzle brakes. Shooting Illustrated liked the general features of the Wildcat SR: “The rifle… has a rugged polymer upper assembly, lower receiver assembly and ambidextrous skeletonized buttstock for light weight and strength. The rear sight is adjustable for both elevation and windage and there is also a ramped post front sight.” We are pleased to see that the Winchester Wildcat SR boasts an integral Picatinny Rail for mounting optics.
Browning X-Bolt Mountain Pro Carbon
We like the Browning X-Bolt rifles. Browning offers good protective coatings on the barreled actions, and the camo treatments are nicely done. For 2021, Browning has a new line of X-Bolt Mountain Pro rifles. These include a new-generation carbon fiber stock that is even lighter, with noise-dampening foam for added comfort. The X-Bolt Mountain Pros also come with a Recoil Hawg muzzle brake that Browning says can reduce felt recoil by as much as 73%. The stainless steel action and barrel come with a protective Cerakote Burnt Bronze or Tungsten finish. And internally the barrel boasts a “proprietary lapping process” for easier cleaning and quicker break-in times. For that custom touch, the bolt and bolt knob are spiral fluted. These new X-Bolt Mountain Pros are not inexpensive. Browning lists an MSRP of $2,399.99 – $2,459.99. Expect “street price” around $2000.00.
Savage Renegauge Competition 12ga Shotgun
Here’s an impressive new 12 gauge shotgun from Savage. This boast an extended magazine tube that holds 9+1 rounds. The looks are notable, with Red Cerakote on the Receiver and mag tube, with a black melonited fluted barrel with ventilated ridb and HI-VIZ front site. The stock adjusts for LOP, comb height, drop and cast and there is a rod recoil buffer in the buttstock. Shooting Illustrated notes that the Savage has an advanced gas system: “The Savage Renegauge Competition shotgun features the DRIV gas system (Dual Regulating Inline Valve) gas system which ensures excess gas vents before it drives the bolt, resulting in consistent ejection, less felt recoil, and a … fast cyclic rate[.]”
Volquartsen Black Mamba-X .22 LR Pistol
Volquartsen has released its new Black Mamba-X pistol for .22 LR competitors in speed matches. This features a Volquartsen’s LLV-4X 4.5-inch Competition Upper with integral universal red-dot mount. The Black Mamba-X features a push-button takedown configuration. Other standard features include: A ½x28 threaded stainless steel, 4.5″ barrel, Volquartsen Accurizing Kit allowing 2.25-pound trigger pull.
FN America FN 509 LS Edge
This new FN 509 LS Edge pistol has a longer slide with cut-outs, aggressive checkering, and good controls. Shooting Illustrated notes the benefits of FN’s smart signt attachment design: “The real key to the FN 509 LS Edge is the sighting system. It has a high front sight with a green fiber-optic insert and serrated front blade to reduce glare. The rear sight is a deep trough.” This patented rear sight design allows a very low red dot position, which gets “the sight real low in the slide and helps it co-witness perfectly with the iron sights.” Various inserts are available for many types of pistol optics.
Right now reloading presses are in high demand. If you are shopping for a single-stage press, here’s a good press you may still find available at many vendors. The Hornady Iron Press™ features a super-strong, pyramid-style cast-iron frame with an open front. A clever optional “automatic” priming system shuttles primers from a vertical tube in the back to the shell-holder in the front. This is very clever engineering. You really should watch the video — it shows the patented auto-priming system in action. The Auto-Prime system is sold separately or as part of the Iron Press Reloading Kit.
Watch this Video to See Gravity-Fed Shuttle Priming System (00:45, 01:00):
Optional Automatic Priming System
The optional auto-priming system is a real selling point for this new press we think. When you move the press handle rearwards, a horizontal bar toggles back to pick up a primer from the column in the rear of the press. Then this same bar move forwards to place the fresh primer in the center of the shell-holder. Hornady explains: “The available gravity-fed Automatic Priming System (sold separately or with the Lock-N-Load® Iron Press™ Reloading Kit), combined with the Accessory Mounting Deck, increases reloading efficiency by allowing more processes to occur simultaneously. The Iron Press™ is the first of its kind to allow the ability to deprime, pause, and remove the case to chamfer & deburr … then replace and prime.” Do watch the video to see the priming system in action.
The broad top of the beefy (26-lb.) Iron Press can hold case prep tools (such as chamfer tool and case-neck brush) and/or a box for bullets or brass. NOTE: This is NOT a turret press — you can only use one die at a time. However, Hornady offers an accessory “Die Caddy” (sold separately) that can hold up to three (3) more dies. That way you can quickly switch from a sizing die to a seater die (or vice-versa). What Hornady calls the “Accessory Mounting Deck” gives quick access to items such as trays for bullets or cases, chamfer and deburr tools, case neck brushes, primer pocket cleaners and other accessories. The Iron Press comes with the Lock-N-Load® bushing system which allows for rapid die changes.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. CZ 457 .22 LR Varmint Precision Chassis Rifle, $899.99
⏺ CZ 457 offers good .22 LR accuracy/function with modern chassis stock
NRL22 rimfire tactical matches are hugely popular. You see a lot of press about centerfire PRS. But there are more NRL22 matches every month than official PRS matches every year! If you want to get started in NRL22 competition, here is a great option. Choose either 16.5″ or 24″ barrel. We like the longer barrel for the extra velocity, but either choice works. Palmetto State Armory has the 16.5″ version for $899.99 while Midway USA has both 16″ and 24″ models for the same $899.99 price. Either way, just add an optic and you’re good to go. Top photo by owner MealTeam6ix9ine who is “super impressed by the rifle” which has the 16.5″ barrel with Rugged Oculus suppressor. The optic is a Vortex Gen II Viper 5-25x50mm on a +15 MOA Area 419 base.
2. Natchez — RCBS ChargeMaster Lite, $239.99
⏺ Best Deal on popular, speedy Scale/Dispenser
Do you need an electronic powder scale/dispenser? Most vendors charge $290-$310 for the popular RCBS ChargeMaster Lite. But now you can get it for just $239.99 at Natchez. You save $60.00, about 20%! The ChargeMaster Lite features an easy-to-use LCD touchscreen and claimed precision of plus/minus 0.1 grains. The unit comes with twin check weights and a convenient plastic cover for the powder pan.
⏺ Very good value for Tac Comp Scope; Good Lens Coatings
Do you enjoy PRS and NRL matches? Here is an excellent scope for that task, offered at a huge savings — 31% OFF normal retail. The Sightron S-TAC 4-20x50mm offers good glass, very accurate tracking, and a nearly ideal 4X to 20X power ratio. This FFP MRAD scope works great for tactical matches. It boasts 22.9 MRAD of elevation adjustment plus nice big, easy-to-turn turrets. This scope features a zero stop, throw lever, and side parallax control that works down to 10 yards. The S-TAC 4-20x50mm provides 22.9 MRAD of elevation adjustment. Note: This may say Duplex Reticle, but the Sightron product number 26016 on the Sightron site (and the product description) indicate this scope has the Mil-Hash-4 (MH-4) Illuminated reticle. That’s a good reticle for tactical disciplines.
4. Plano AirGlide Vertical Loading Rifle Case
⏺ Great case for range trips, sadly going out of production
The Plano AirGlide case is our favorite case for regular visits to the range. The rifle drops in from above. There is no pressure put on the scope turrets laterally or from above. This cases are good for rifles up to about 50″ overall (such as a benchrest rifle with a 27″-28″ barrel). We are listing this AirGlide case here because the AirGlide is being discontinued. In fact, it is no longer listed on the Plano website. So get one while you can. Here are two sources, but Airgun Depot is waiting for inventory:
Among injection-molded plastic rifle cases, Plano’s AirGlide™ case is unique in holding a rifle vertically, in foam cradles. This allows ample room for the 3″-wide fore-ends on BR and Varmint rifles. The foam blocks front and rear can even be trimmed for a custom fit, while velcro webbing straps hold the rifle securely. The AirGlide’s hinged top-opening lid provides ample clearance for large target scopes, with no side load on the turrets. Measuring 51 1/2″L x 7 3/4″W x 12 1/4″H, the AirGlide can handle rifles up to 50″ in length. SEE: Airglide Video Review.
5. Grafs.com — Frankford Platinum Case Prep Center
⏺ Versatile, easy to use unit with 4 powered heads
Grafs.com now has the Frankford Platinum Case Prep Center for $89.99 on SALE. This aluminum-body unit features 4 powered tool stations and comes with: (1) inside chamfer tool; (1) outside deburring tool; (1) small primer pocket scraper; and (1) large primer pocket scraper. The machine’s 8-32 threaded output shafts accept a wide variety of aftermarket case prep tools. The 200 RPM shafts are efficient. NOTE: If you want a tool that can TRIM cases, as well as prep cases, check out the Frankford Case Trim & Prep Center for $80 more — $169.95 at MidwayUSA.
6. EuroOptic — Trijicon Tenmile Scope Sale
⏺ These Trijicon optics compare well with NF for much less
Trijicon Tenmile scopes have quickly become popular with F-Class, PRS, and ELR competitors. Check out the Trijicon Tenmile scope sale where you can pick up any of these innovative scopes that feature lit reticles, large 34mm diameter tubes, and many other good features. These are really good scopes for the money. And now’s the time to buy with massive discounts during this sale. For example the Tenmile 4-24x50mm with MRAD ranging is marked down from $1799.00 to $1176.00. And the Tenmile 4.5-30x56mm LR scope is marked down from $2600.00 MSRP to $1699.99 — Save over $900!
7. Amazon — Tipton Best Gun Vise, $87.54
⏺ Versatile, stable, works with all rifles, including ARs
You need a stable platform when cleaning your long guns, but most gun cradles are too light or unstable to do the job properly. If you’re looking upgrade to a better solution, grab the Tipton Best Gun Vise. The vise was designed to accommodate the widest possible array of firearms for cleaning, maintenance, or gunsmithing. This vise is easily configurable to handle bolt-action rifles, break-open shotguns, AR-15s, and handguns. You can also purchase this excellent Gun Vise for $89.99 at Midsouth.
⏺ “Must Have” Upgrade for Harris Bipods — works great, low cost
This lever handle replaces the thumbnut on tilting bipods to make locking them down easier. With the Alpha-Bravo Bipod Lever installed, a quick rotation of the lever allows you to go from easily tiltable to completely locked down. That way you can level your rifle in seconds and then be rock solid. You can also set the tilt resistance to a medium level that holds steady but allows some rifle rotation (L/R tilt) when you want. The Long Model Bipod Lever is on sale now for just $10.99. You can also get a Shorter Lever for $14.99. Both lever handles fit Harris Model S and similar bipods.
⏺ A good deal at twice the price, with above average 27 dB NRR
This Walker’s Ultra Slim Muff and Eyewear Combo Kit is truly a GREAT deal. Buy this inexpensive kit as a spare Muffs/Glasses set to keep in your vehicle or range kit. Each combo kit includes earmuffs along with a nice set of wrap-around shooting glasses. The muffs have an excellent 27 dB Noise Reduction Rating (NRR). And the Z87.1-approved glasses boast impact-resistant, polycarbonate lenses with 99% UV Protection.
10. Amazon — Jialitte Scope Bubble Level, $10.99
⏺ Effective and affordable — works for both 30mm and 1″ tubes
All serious rifle shooters need a scope level. This nicely designed Jialitte Scope Bubble Level features a 30mm milled inside diameter, plus an inner insert ring so it will also fit 1″-diameter main tubes — that dual-diameter versatility is a nice feature. We also like the way the unit is nicely radiused, and has a low profile in the middle. Price is just $10.99 with free shipping. User reviews have been very positive. You could easily pay $35.00 or more for a 30mm scope level.
