When neck-turning cases, it’s a good idea to extend the cut slightly below the neck-shoulder junction. This helps keep neck tension more uniform after repeated firings, by preventing a build-up of brass where the neck meets the shoulder. One of our Forum members, Craig from Ireland, a self-declared “neck-turning novice”, was having some problems turning brass for his 20 Tactical cases. He was correctly attempting to continue the cut slightly past the neck-shoulder junction, but he was concerned that brass was being removed too far down the shoulder.
Craig writes: “Everywhere I have read about neck turning, [it says] you need to cut slightly into the neck/shoulder junction to stop doughnutting. I completely understand this but I cant seem to get my neck-turning tool set-up to just touch the neck/shoulder junction. It either just doesn’t touch [the shoulder] or cuts nearly the whole shoulder and that just looks very messy. No matter how I adjust the mandrel to set how far down the neck it cuts, it either doesn’t touch it or it cuts far too much. I think it may relate to the bevel on the cutter in my neck-turning tool…”
Looking at Craig’s pictures, we’d agree that he didn’t need to cut so far down into the shoulder. There is a simple solution for this situation. Craig is using a neck-turning tool with a rather shallow cutter bevel angle. This 20-degree angle is set up as “universal geometry” that will work with any shoulder angle. Unfortunately, as you work the cutter down the neck, a shallow angled-cutter tip such as this will remove brass fairly far down. You only want to extend the cut about 1/32 of an inch past the neck-shoulder junction. This is enough to eliminate brass build-up at the base of the neck that can cause doughnuts to form.
The answer here is simply to use a cutter tip with a wider angle — 30 to 40 degrees. The cutter for the K&M neck-turning tool (above) has a shorter bevel that better matches a 30° shoulder. There is also a 40° tip available. PMA Tool and 21st Century Shooting also offer carbide cutters with a variety of bevel angles to match your case shoulder angle*. WalkerTexasRanger reports: “I went to a 40-degree cutter head just to address this same issue, and I have been much happier with the results. The 40-degree heads are available from Sinclair Int’l for $13 or so.” Forum Member CBonner concurs: “I had the same problem with my 7WSM… The 40-degree cutter was the answer.” Below is Sinclair’s 40° cutter for its NT-1000, NT-1500, and NT-4000 neck-turning tools. Item NT-3140, it sells for $12.95. There is also a 40° cutter for the NT-3000 tool, item NT-3340 ($13.95).
Al Nyhus has another clever solution: “The best way I’ve found to get around this problem is to get an extra shell holder and face it off .020-.025 and then run the cases into the sizing die. This will push the shoulder back .020-.025. Then you neck turn down to the ‘new’ neck/shoulder junction and simply stop there. Fireforming the cases by seating the bullets hard into the lands will blow the shoulder forward and the extra neck length you turned by having the shoulder set back will now be blended perfectly into the shoulder. The results are a case that perfectly fits the chamber and zero donuts.”
Did you miss Black Friday? Well don’t fret. Sinclair International is still offering 10% off all orders of $149.00 or more. This hefty discount is valid through 11:59 pm on Monday, December 2, 2013. There are many good deals to be had. Remington 700 Short Action receivers are on sale for $389.99. Forum member JohnHenry notes that Sinclair has benchrest LV 1:14″-twist 6mm Bartlein barrels on sale for $299.99, and you’ll get an additional 10% off with Discount Code EBJ. Use Code EBJ at checkout to save today and on Cyber-Monday (12/2/2013).
Are you thinking, “Snow’s on the ground, winter’s here, I won’t be competing until spring.” Well think again — there are opportunities to compete indoors during these cold months.
The 2014 NRA National Indoor Rifle & Pistol Championships start January 1, 2014. There will be indoor matches around the country with a variety of disciplines including Air Pistol, Rimfire Pistol, Air Rifle, and Rimfire Rifles. There is even a BB gun class for Juniors. The Indoor Championships involve multiple sectional tournaments, held in a variety of states from January through mid-April. This is like a super-duper postal match. Your results are sent to the NRA where they’re compared to other shooters. Winners are determined in late May. It’s a fun way to compete with many other shooters and it’s easy to get involved. There will be nearly 300 sectionals in 2014, so you’ll probably find an event close to home. Here are dates for 2013:
For more information contact these NRA staffers: Dian Bullock, (703) 267-1482 (Rifle); Ann Boyd, (703) 267-1452 (Pistol); Tori Croft, (703) 267-1473 (Collegiate).
The 50m Free Pistol is one of the events in the NRA National Indoor Championship. It takes skill — the pistol is shot one-handed, with iron sights, and the Ten-Ring is only 50mm (about 1.97″) in diameter. A competitive world-class score is 560 or better out of 600 possible points. Learn more about this challenging discipline in this USA Shooting video:
The NRA’s American Rifleman Online website has an excellent article showing how to construct a rock-solid Reloading Bench. There are plenty of photos, and a detailed set of Bench Blueprints showing all dimensions and listing all needed materials. This bench is very well designed, with many deluxe features, such as an upper drawer with fitted slots for die boxes, and large lower drawers with 100-lb rated slides to store heavy materials or tools. If you have good wood-working skills this would be an excellent project.
The author, Dave Campbell, offers good advice on building the bench top: “I ripped a sheet of 3/4″ AC plywood into two 24″ wide pieces and cut them to 72″ long. Then I glued them together to form a 72″ long, 1 1/24″ thick top. The trick here is to keep the edges smooth and flat so that the laminate will adhere properly and without voids. I chose a light grey laminate finish for the top because it’s easier to see what I am working on and keep clean. If you have never worked with laminate, remember it’s prudent to glue and rout the edges flush before gluing on the top. The top was attached to the carcass with eight steel L-shaped angle brackets and No. 10×1 1/4″ wood screws.”
Our readers have been getting some great deals over at Brownells.com, with the big Black Friday Sale happening right now. Brownells’s Black Friday specials are good through 11:59 pm CST on December 2, 2013. Here is a Discount Code that can save you 10% on all Brownells orders over $149.00 (Use Code EBH at checkout). Happy shopping boys and girls….
When we first ran this video a couple years back, readers were amazed at the off-hand, rapid-fire shooting skills of this young, German hunter, armed with a Sauer 202 rifle.
Check out this video of a young German hunter, Franz Albrecht Öttingen-Spielberg. Shooting off-hand with a Sauer 202 bolt action, he makes multiple kills on wild boar running at full speed. Half way through the video, a pack of boar crosses right to left, running fast. You need slow motion to see all Franz’s hits as he engages one animal after another. He doesn’t hit with every shot, but a quick count shows that nearly half his shots, fired rapid-fire from a standing position, were solid takedowns. Notice how Franz “leads” his prey, moving the muzzle from right to left along the animals’ path.
Slow-Mo Video Reveals Knock-Down Power of 7mm Rem Magnum
Near the beginning of the video, slow-motion footage reveals bullet trace, and the bullet’s impact on a running boar. The shot takes the boar right at the top of the shoulder and the animal goes down in a heap. This is impressive shooting. The video shows what is possible with a skilled marksmen, a powerful cartridge (7mm Rem Magnum), and an accurate, smooth-cycling bolt gun.
Forum members have asked “what’s the best option in a spotting scope in the $500 to $1000 price range?” We’d certainly have to include Kowa spotting scopes on the “short list” for value-priced, high-performance spotters. And now Kowa spotting scopes are cheaper than ever, thanks to Bullets.com’s Holiday Kowa Promotion. Kowa Spotting scope and binoculars are on sale at Bullets.com for up to 26% off regular list prices.
If you need an affordable spotting scope for High Power matches or hunting, consider the 66mm or 82mm Kowas. If you want a no-compromise, ultra-low-dispersion glass, category-leading spotting scope, take a look at the 88mm Kowa Prominars. These have been rated among the “best of the best” in a variety of independent spotting scope comparison tests. Bullets.com is also discounting a wide range of Kowa binoculars.
Here’s the kind of sale we really like — serious savings on very high-quality products, the top name brands we respect. EuroOptic.com is running a Black Friday & Cyber-Monday Sale that should interest our readers. The brands are top-tier: Accuracy Int’l, Blaser, Benelli, Heckler & Koch, Leica, Zeiss. The deals are sweet: $100 off Accuracy Int’l Rifles, a Leica CRF Rangefinder at $379, Zeiss Conquest 3-9×40 scope for just $329.00 — and there are many more deals (see below). If you have been wanting an EOTech optic, these are now discounted 10% and a $60.00 Factory Rebate is available.
These discounted prices are good through Tuesday, December 3, 2013. And in the Sale Email Announcement, EuroOptic.com declared: “We will not be undersold — if you find a better price, call us at (570) 368-3920″.
Today is Thanksgiving. After partaking in the traditional Turkey Day feast, we know many of our readers will find time during the holiday to head to the range. A Thanksgiving Day shoot is a fun excursion, and a great way for young and old family members to share time together. For all you T-Day marksmen, we offer a special turkey target. This was created by our friend and Forum member Pascal (aka “DesertFrog”).
We’ve packaged the turkey target along with five (5) other varmint/animal-themed targets for your shooting pleasure. These are all offered in .pdf (Adobe Acrobat) format for easy printing.
Program Promotes Family Hunting Opportunities
Speaking of turkeys and families going shooting together, we’d like to give a plug for the “Families Afield” program. A joint effort of the Nat’l Shooting Sports Foundation (NSSF), U.S. Sportsmen’s Alliance (USSA), and National Wild Turkey Federation (NWTF), the “Families Afield” program works to expand the opportunities for young hunters with adult mentors. The goal of the program is to increase the number of young people getting involved in hunting. For every 100 adult hunters today, only 69 youth hunters are coming up to take their place. “Families Afield” works to reverse that trend. Several states that were restrictive to youth hunting have signed into law “Families Afield” legislation. These new laws make it possible for young hunters and their families to enjoy hunting traditions together. CLICK HERE to learn more.
Can a pumpkin be launched over a mile? Can a gourd go super-sonic? These vital questions will be answered on Thanksgiving Day as the Science Channel covers the annual Punkin Chunkin World Championship held in Sussex County, Delaware. The previous record, set in 2011 by the Second Amendment Too Air Cannon, is 4,329.37 feet, or 0.8199 miles (1443 yards). The heavy artillery will be out in force this year — trying to break that record, and maybe hit the mile mark in the process.
Each year, competitors roll out some amazing machines designed to propel pumpkins “farther, higher, faster”. The mighty air cannons are the distance kings, but the wild and crazy devices in the torsion, trebuchet, catapult, and centrifugal divisions are impressive to watch. Many of these fearsome-looking machines replicate the designs of medieval military siege weapons.
Team Builds $168,000 Air Cannon in Effort to Go Supersonic and Chunk One Mile
With the goal of launching a pumpkin one mile, considered the “Holy Grail” of Punkin Chunkin, the American Chunker team has developed one of the biggest, baddest air cannons ever. With a new 540-horsepower compressor pumping out 500 psi of pressure, the creators of this massive cannon hope to send a pumpkin supersonic. This cannon represents an investment of $168,000 and 2800 man-hours. State-of-the art sensors are used to gauge pressure and measure the pumpkin’s speed in flight. Will the team break the sound barrier? Watch the Science Channel special to find out.
Great Video on High-Tech Air Cannon (Amazing Stuff!)
To catch all the Punkin Chunkin action, tune your TVs to the Science Channel on Thanksgiving Day, November 28th. At 8:00 PM Eastern, the Science Channel devotes a full hour to America’s wildest display of agricultural artillery — Punkin Chunkin. This hour-long special TV event covers the 2013 World Punkin Chunkin Championship. This fun-filled event, held near Bridgeville, Delaware each November, draws up to 70,000 spectators, raising money for charity. The Punkin Chunkin special is hosted by Tory Bellici, Kari Byron, and Grant Imhara from Mythbusters. Like Big Guns? View Chunkin Air Cannons Gallery.