For years we have touted the advantages of Burris Signature rings, with polymer Pos-Align Inserts. PRS/NRL shooters take note — this technology is available in a beefier, heavy-duty ring system for tactical rifles. The impressive Burris XTR Signature Rings offer six (6) clamping bolts per ring plus strong, dual steel base-clamps that self-center on Weaver or Picatinny rails. These aluminum XTR Signature Rings provide strength and holding power, plus the key benefits of Pos-Align inserts. As impressive as XTR rings are — they aren’t that expensive, with 1″-diameter XTRs starting at about $90.00 per pair (30mm and 34mm XTRs cost a bit more).
The polymer inserts in Signature rings perform three key functions. First, the inserts provide full, uniform scope-to-ring contact, with no need for lapping. You get a very secure “grip” on your scope without ring marks. Second, the Pos-Align inserts can provide elevation “pre-load”. With eccentric (offset) inserts, you can raise the back of the scope relative to the front, gaining up to 54 MOA of built-in elevation, without the need for expensive tapered bases. Third, the offset inserts can be rotated clockwise or counter-clockwise to shift point of impact. This lets you zero your rifle easily while keeping the turrets in the center of their travel.
Burris XTR Signature Rings are offered in 1″, 30mm, and 34mm diameters, and three (3) different heights: 1″, 1.25″, and 1.5″. Each ring set includes two sets of concentric inserts and one set each of the following offset inserts: +/-5 MOA, +/-10 MOA, +/-20 MOA. These allow you to “pre-load” elevation and/or center up your cross-hairs.
– Pre-load Elevation. No need for expensive tapered bases for long-range shooting.
– Correct misalignment caused by off-center receiver holes.
– Correct for bases or rings being slightly off-center.
How to Pre-load Elevation
To add elevation, set the Pos-Align Offset Inserts to raise the rear of the scope and lower the front. As long as there remains sufficient clearance between the front objective bell and the barrel, Burris recommends lowering the front of the scope the most and raising the rear of the scope the least. The amount of actual elevation “pre-load” will depend on the ring spacing (see chart). In the illustration, with 4.75 inches between ring centers, a +/- 20 MOA pair in the front combined with a -/+ 5 MOA pair in the rear will yield +25 MOA of total elevation. (If the rings are positioned further apart, you’ll get less elevation pre-load.)
Using Inserts to Adjust Point of Impact in Any Direction
Although it is convenient and most understandable to refer to the ring inserts as a “bottom” or “top” insert, the inserts may be rotated to any angle within the scope rings. This allows the shooter to correct the point-of-impact in any direction. The drawings below show how the inserts can be rotated to induce both elevation and windage changes at the same time.
Product tip from Boyd Allen. We welcome reader submissions.
Looking for a very affordable first rifle for a young family member? Here’s one of the best low-cost options you can find among .22 LR rimfire rigs. The Rossi RS22 is a reliable, semi-auto rifle that comes equipped with barrel-mounted iron/fiber optic sights. There are also dovetails on the receiver for mounting scope rings. The RS22 also takes most Mossberg 702 magazines.
The Rossi RS22 features an 18″ free-floating barrel, adjustable fiber optic sights and a synthetic Monte Carlo stock. For added accuracy, 3/8″ dovetail mounts allow the mounting of a scope or other optic (and there is a model with a Picatinny rail).
There are multiple RS22 models. The basic RS22 with black stock and iron sights is $133.99 at KYGUNCO. An upgraded iron sights version with a threaded barrel (for suppressor) is $146.76 at Palmetto State Armory (PSA). If you will always be using a scope, consider the RS22 model with Picatinny scope rail and threaded barrel (but no iron sights) — it is on sale now for just $129.99 at PSA.
Rossi RS22 Specifications:
Model: RS22 Semi-Auto, .22 LR
Barrel: 18″ Free-floating
Stock: Black Monte Carlo Synthetic Stock
Overall Length: 36.25″
Weight: 4.1 lbs.
NOTE: The Rossi RS22 on sale has a matte black stock.
Two Video Reviews of Rossi RS22
The above video review of the Rossi RS22 confirms its reliability and build quality. The reviewer praised the fiber-optic iron sights and liked the magazines. After fitting a scope to the rifle’s built-in dove-tail, the tester got excellent accuracy with CCI ammo at 25 yards. Ten shots basically formed one half-inch hole. (See video 8:24 – 8:50 and target at right.) That’s good enough for an NRL22 match. Pretty impressive for a $134 rifle!
Gunblast.com also tested the Rossi RS22. This “dandy little rifle” performed great, with flawless semi-auto feeding and cycling for hundreds of rounds. Accuracy was quite good. The tester praised the fit and feel of the stock and noted it has sling swivel studs and well-protected sights. The RS22 can also use 25-round Mossberg magazines.
Today’s the day folks — the first full day of the 2023 NRA Convention. The 2023 NRA Annual Meetings & Exhibits will take place at the Indiana Convention Center on April 14-16, 2023 in Indianapolis, Indiana. The Exhibit Hall is open all three days and will showcase over 14 acres of guns and gear from over 600 manufacturers and retailers.
There are over 600 exhibitors at the large Convention Center. Leading companies including Berger Bullets, Lapua, Vihtavuori Powder, Hornady, Sierra, Kimber, Remington, Smith & Wesson, and countless more.
Organized events include the NRA-ILA Banquet and Auction, the NRA-ILA Leadership Forum, plus multiple seminars. There will be appearances from notable celebrities, and a major Saturday concert with leading musical artists. The NRA Foundation dinner and auction was held last night. Here are the major events set for Friday, Saturday, and Sunday, April 14-16, 2023:
Artistry in metal — Engraving has long been used to decorate fine firearms. The examples shown here prove that engraving is not a lost art. There still remain fine craftsman who can engrave beautiful designs into the metal components of pistols, rifles, and handguns. Above is a spectacular Dragon-engraved Korth revolver from Nighthawk Custom — an amazing example. Below are seven beautiful examples of engraved semi-auto pistols, from a tiny Colt .25 ACP to Chuck Yeager’s gold-plated Beretta.
Centennial 1911 from Colt — Marking 100 Years
In 2011, to celebrate the 100th birthday of the 1911 hangun, Colt created a spectacular, fully-engraved “Anniversary Edition” pistol. J.M. Browning’s 1911 pistol was officially adopted by the U.S. Army on March 29th, 1911. (The U.S. Marine Corps and U.S. Navy adopted the 1911 pistol roughly two years later). This Centennial 1911 is pimped to the max, complete with gold inlay and genuine ivory grips.
One-of-a-Kind Fully Engraved Walter Q5
On display at the 2019 IWA Outdoor Classics Show in Germany was this stunning fully-engraved Walther Q5 pistol. Note how even the magazine end plate is engraved. On the slide is an American Eagle and the quote “We the People”. Those rare wood grips are also very eye-catching and handsome. This may be the fanciest Walther pistol on the planet.
The Right Stuff — Chuck Yeager’s Gold-Plated Beretta
Here’s another pistol with a famous owner “The Right Stuff” Pilot, Chuck Yeager, the first human to break the sound barrier. This Beretta has extra value because it was owned by pilot Chuck Yeager. Photo NRA Museum.
Stunning Engraved Trio — Colt, Mauser, and Luger
Here is a matching set of three three beautifully engraved pistols by the late Indiana engraving wizard Ben Shostle — a Luger, a Mauser, and a diminutive Colt. By themselves, these three matching pistols would make a prized handgun collection. Photo courtesy Amoskeag Auction Company.
Smith & Wesson Model 41 — 50th Anniversary Edition
The .22 LR Smith & Wesson Model 41 is one of our favorite rimfire target pistol. First released in 2008, the engraved model 41 combines superior accuracy with stunning appearance.For $1700.00 to $2000.00 you can find the fully engraved, 50th Anniversary Model 41 in presentation case on Gunbroker.com.
Need a high-quality reloading scale, but can’t afford an $800 A&D force restoration scale? Then you’re in luck. Starting at 12:00 pm Central Time on Thursday, April 13th, 2023, you can get the excellent Creedmoor Sports TRX-925 scale for $249.95. The deal — a whopping $100 savings off the regular $349.95 price — works for the first 249 customers. Don’t delay — this is a limited $100 Off Sale.
NOTE: This $100 OFF Sale is Good for the First 249 buyers ONLY!
The Sale commences at 12:00 noon Central on Thursday, April 13, 2023
About the Creedmoor Sports TRX-925 Precision Scale
The Creedmoor Sports TRX-925 scales are produced in an ISO9001:2008 approved facility and utilize laboratory-grade electronics, including carefully-tuned and optimized strain gages. The TRX-925 also includes an anodized static-free powder pan, 925 Grain maximum capacity, and a modular draft shield.
The TRX-925 measures powder weights in GRAINS not grams. The vast majority of scales on the market utilize grams as their native unit of measure and simply convert the measured weight from grams to grains by using a formula. Unfortunately, this method of behind-the-scenes conversion can cause rounding errors that affect the reported weight. This TRX-925 scale offers true +/-.01 grain resolution for superior weighing accuracy.
To ensure that the TRX-925 maintains the level of precision that serious reloaders demand, each Creedmoor Sports TRX-925 comes standard with three F-1 class calibration weights (2g, 10g 50g) each with its own protective storage case.
A while back, RifleShooter Magazine released a list of the Ten Greatest Lever-Action Rifles of All Time. Writing for RifleShooter, Brad Fitzpatrick examined a wide selection of lever guns produced in the past 150 years, and came up with this short list of ten “all-star” lever action rifles:
Savage Model 99
Winchester Model 1873/73
Winchester Model 1888/88
Winchester Model 1892/92
Winchester Model 1894/94
As with all “Top 10″ lists, this will be controversial. Where is the Winchester model 1866 “Yellowboy”, the favorite of Native Americans? Where is the iconic Winchester model 1895, the beloved gun Teddy Roosevelt called “Big Medicine”? But other choices are hard to fault. The Henry Rifle, the first popular cartridge lever gun, surely belongs on the list. And, believe it or not, the Winchester Model 94 is the best-selling sporting rifle of all time in the USA, according to RifleShooter.
So what do you think of RifleShooter’s Top 10 list? Does it make sense, or did RifleShooter magazine get it wrong? NOTE, on the Rifleshooter Lever Gun Page, to see descriptions/photos of ALL the guns, you need to click the gray arrows that appear (barely) below each gun description (see below). That will scroll through the ten guns horizontally, back and forth.
Fitzpatrick writes: “The lever action played a very legitimate role in America’s westward expansion. It could bring meat to your table or protect your land and assets against rustlers. Nostalgia aside, the lever gun is an effective hunting tool for those willing to live within its limitations. While it can’t beat a bolt gun with a light trigger and free-floated barrel in a long-range shooting competition, a lever action in the right hands can be rather accurate, especially given new advancements in rifle design and bullet technology.”
Historic American Arms — Teddy Roosevelt’s Lever Guns
These two lever action rifles, owned by President Theodore Roosevelt, are part of the NRA Museum collection. First is a Winchester 1886 rifle known as the tennis match gun because Roosevelt used winnings from a tennis match to buy it. Below that is a suppressed Winchester model 1894 rifle. Roosevelt liked to shoot varmints around Oyster Bay (Long Island, NY) with this gun so he wouldn’t disturb his neighbors — the Tiffany and Du Pont families.
This week, Shooting USA TV spotlights the 2022 GAP Grind, the largest PRS Pro-Am Tactical match with nearly 400 competitors. The 10th Annual GA Precision/Elite Tactical GAP Grind PRO-AM was held September 30 through October 2, 2022 at the K&M Shooting Complex in Tennessee. The GAP Grind, the largest, most popular PRS match in the world, drew nearly 400 amateur and pro shooters. Recognized as the premier PRO-AM precision rifle match with both individual and team competition, the GAP Grind has introduced thousands of new shooters to the sport since its inception. It was great to see the GAP Grind successfully mark its 10th Anniversary.
SHOW TIMES: This Shooting USA Episode airs Wednesday, April 12, 2023 at 9:00 PM Eastern and Pacific; 8:00 PM Central. If you miss the regular broadcast, you can stream the show at any time on Vimeo for $0.99 per episode.
In this video Eagle Eye Shooting Shares Highlights from the 2022 GAP Grind
Big Prize Table at 10th Annual GAP Grind Event
The year’s largest PRS match drew hundreds of attendees, and more than 80,000 rounds were fired throughout the three-day event. Bushnell gave out $5,000 to the top place finishers and added over $5,000 worth of product to the prize table. Trophies were awarded to the top 5 teams, top 5 professionals, and to the top 5 amateurs.
Lots of Action, with 20+ Stages
The GAP Grind is a challenging, “high tempo” match with minimal down-time between stages. Over the course of 20+ stages, competitors will fire 200+ shots at a variety of steel, paper, moving, and reactive targets out to 1,200 yards. Targets vary in size/difficulty based on the shooter’s position, distance, and time allotted. Most stages include “stressors” — i.e. time limits or required movement(s).
This extensive, 45-minute video shows many of the 2022 GAP Grind Stages
GAP Grind Pro-Am Format — Seasoned Shooters Help Newcomers
The GAP Grind typically attracts nearly 400 competitors — half experienced shooters and the other half newcomers to the sport. The key to growing the shooting sports is attracting new shooters. The best way to bring in “new blood” seems to be the Pro-Am type format. At the GAP Grind, experienced shooters share their knowledge and guide the new shooters through the competition.
GAP Grind Hardware
You’ll find the latest and greatest PRS hardware at the GAP Grind. Over the past few seasons, most top competitors have “stepped down” from the 6.5/6mm Creedmoor to the smaller, more efficient 6mm Dasher, 6BRA, 6 GT and other 6mm cartridges. The Dasher offers excellent accuracy with less recoil than the 6.5 Creedmoor. Also, many competitors will be switching to the impressive new Zeiss FFP LRP S3 and S5 scopes in the months ahead.
Suppressor Processing at NRA Convention Silencer Central, America’s largest silencer dealer, will allow NRA Convention attendees to submit their ATF eForm 4 application onsite with purchase. This special program will be available at the Silencer Central booth (#7963) at the NRA Annual Meeting & Exhibits, April 14-16, 2023, in Indianapolis, Indiana.
To streamline the process of obtaining a suppressor, attendees will be able to purchase a silencer at the Silencer Central booth (#7963), have their photo and fingerprints taken, generate their free NFA Gun Trust, setup a no-fees, no-interest payment plan for just $199 down, receive assistance registering for their ATF.gov account, and get submitted to the ATF all at the event.
Silencer Central CEO Brandon Maddox stated: “This new process helps us deliver on that commitment by allowing our customers to purchase, certify, and submit right on the spot.” This can save suppressor buyers many days or even weeks in processing time.
“We make buying silencers simple,” said Maddox. “While others might say they share that claim, we continue to lead the pack with our investment in innovation and technology while approaching our customer experience with a lens for continuous improvement.”
Silencer Central delivers silencers directly to customers in the 42 states where silencers are legal. Silencer Central’s process has revolutionized the way suppressors are sold and reduced unnecessary hurdles to silencer ownership. For more information, call 888-781-8778 or visit SilencerCentral.com.
Berger’s James Fox won the 2023 California Regional High Power Service Rifle Championship shooting Berger factory ammunition and 80.5gr bullets. Fox had a Grand Aggregate score of 1282-48X. Notably, at the closer ranges, Fox shot Berger factory-loaded .223 Rem 77gr OTM ammunition in his AR-platform rifle. For the 600-yard targets, Fox shot ammo loaded with Berger 80.5gr Fullbore bullets. Fox noted: “The Berger 80.5 Grain Fullbore bullets are truly the ‘easy button’ for Service Rifle, because they seem to just shoot in any barrel I have[.]”
The 2023 California Regional Service Rifle High Power Championship was hosted by the Coalinga (CA) Rifle Club on April 1st and 2nd, 2023. With two days of shooting, Fox finished in first on Day One with a score of 792-33X, and first again on Day Two with a 490-15X. In High Power Service Rifle, competitors test their skill in four stages: 200yd Slow-fire Standing, 200yd Rapid-fire Sitting (or kneeling), 300yd Rapid Prone, and 600yd Slow-fire Prone.
With the vast amount of rain California has received in 2023, the Coalinga Range was lush and green. The shooting conditions were also quite good at this April match, with minimal mirage, and mostly consistent winds, making for fairly “easy” shooting and high scores. Competitor Greg Brown noted: “The weather conditions were very pleasant and the winds mild this year. This wind was not a factor for off-hand which helped everyone to generally good scores at the 200-yard line. The winds were somewhat swirly for 300-yard Rapid Fire stage both days and cost some points lost. Conditions for the 600-yard stage looked benign, but tricky enough to prevent any perfect scores, but several 199s were fired on Saturday.”
Archive photo from a past year. The Coalinga Range was far more green and lush in April 2023.
Berger Ammo and Bullets Used by James Fox
“The California Regional Service Rifle Championship was the start to my 2023 shooting season. It was 23 years since the last time I shot at the Coalinga Rifle Club, which both times have resulted in very favorable outcomes for me”, stated Fox. “The first time in 2000 I earned my last Leg Points to become a CMP Distinguished Rifleman, and this year winning the Championship for the first time. During the two-day Aggregate match, I found some early success in the Rapid-fire Sitting stage at 200 yards, where I shot a sub 1-MOA group using Berger’s .223 Remington 77gr OTM ammunition. And later in the day at 600 yards, I fired Berger 80.5gr Fullbore bullets as they held great elevation allowing me to keep rounds in the middle, despite the wind conditions. The Berger 80.5gr Fullbore bullets are truly the ‘easy button’ for Service Rifle, because they seem to just shoot in any barrel I have, with a wide range of powder charges, Vihtavuori N140 seemingly being the best.” Fox will compete next month at the CMP Eastern Games.
Abundant Grass After Much Rain Attracted Cattle to the Range
Greg Brown noted that there were some special challenges at this match — grazing cattle: “The Coalinga Range was at its most scenic this early April time with deep green hills and the grazing yearling steers getting fatter by the hour. Several times the cattle grazed too lose and the shooters turned cowboys had to wrangle them safely off the range.”
Do you occasionally get completely unexplained flyers, or have a shot land straight down at 6 O’Clock, right below your point of aim? That could be caused by poor or inconsistent trigger technique. How you pull the trigger can and does affect your accuracy.
Many gun enthusiasts start with pistols. When they later start shooting rifles they may carry over some not-so-good practices acquired from shooting handguns with heavy 4 to 6-pound trigger pulls. You may want to “re-learn” your trigger techniques to get better rifle results.
Shooting Sports USA has a good article on trigger technique that offers many useful tips. That article also has many helpful illustrations, including the one shown above. Another illustration shows different types of trigger shoes (straight vs. curved) and explains how each makes a difference: “With a lightly curved trigger, the shooter’s finger can contact the trigger either high or low according to preference. Higher contact will increase the resistance.” READ ARTICLE HERE.
The article analyzes common errors, such as pulling the trigger with the very tip of the finger rather than the pad of the index finger: “Using the tip of the finger can lead to lateral pressure on the trigger, which throws off the shot.”
The article also explains that you should check your trigger regularly to make sure it is functioning properly and is not out of adjustment: “Just like any other moving part, the trigger can suffer from wear. In such a precise mechanism, tiny amounts of wear can cause major problems.”
The ergonomics of the Eliseo Tubegun allow a nice, straight trigger pull.
Trigger Tips
Six Suggestions for Making your Trigger Control More Consistent.
1. If your triggers are adjustable, set the pull weight appropriate to the discipline. For a hunting rifle, you don’t want an ultra-light trigger pull. For High Power, you may want a two-stage pull, while on a Benchrest rifle you may prefer a very light trigger.
2. If you have a two-stage trigger, experiment with different combinations of First Stage and Second Stage.
3. Have a friend watch you as you pull the trigger, and maybe even take a close-up video as you pull the trigger. This can reveal a variety of flaws.
4. Practice dry-firing to see if flaws in trigger technique are causing gun movement.
5. As an experiment, try pulling the trigger with your middle finger. Ergonomically, the middle finger has a more straight alignment with the tendons in your hand. This exercise can help you identify alignment issues with your index finger.
6. For stocks with adjustable Length of Pull you may want to set the LOP differently for bench shooting vs. prone or F-Class shooting.
When Only the Best Will Do…
German-made Bix’N Andy triggers, available from BulletCentral.com, are among the very best you can buy. Available in both single-stage and two-stage, Bix’N Andy triggers are extremely precise, repeatable and smooth. The unique internal, friction-reducing roller ball system allows for extremely low reset force, yielding an ultra-crisp let-off. Bix’N Andy triggers can be fitted with a variety of trigger shoes according to shooter preference.
Suppressor Processing at NRA Convention
