On Wednesdays, the U.S. Army Marksmanship Unit often publishes a reloading “how-to” article on the USAMU Facebook page. One “Handloading Hump Day” post covered bore-cleaning, specifically the use of pull-through style bore-snakes. Visit the USAMU Facebook page each Wednesday for other helpful tips.
Today, we’ll shift from handloading to rifle bore cleaning and maintenance, with information courtesy of the USAMU’s Custom Firearms Shop. We recently had some inquiries about bore cleaning, and this seems a good opportunity to share. After all, even the best handloads won’t yield their full potential in a poorly-cleaned and maintained rifle.
NOTE: Hoppes claims a trademark on the term “BoreSnake” (one word, no hyphen). For this article, the USAMU has used the term in hyphenated form, two words. We believe the USAMU is referring to a Hoppes Brand Boresnake, not a different bore cleaning rope.
BORE-SNAKES: MIRACLE REPLACEMENT FOR THE CLEANING ROD?
The experiences of both our firearms test specialist and this writer have given no evidence that proper use of a clean bore-snake will damage a match barrel. Of course, one does not pull the bore-snake at an angle to the crown when removing it — pull it straight out, parallel to the bore’s direction, to prevent crown wear over time.
Bore-snakes are very useful for some applications (primarily a hasty, interim wipe-down). In [my] experience they cannot replace a thorough cleaning with a proper rod and brushes. While the experiment cited here involves rimfire, it may help illustrate. Several years ago, the writer used his new, personal Anschutz to investigate the bore-snake issue. It had been fired ~350 rds with match ammo and had had 3 typical rod/brush cleanings.
Next, starting with a clean bore, the writer fired 300 more rounds without cleaning in order to build up a “worst-case” fouling condition. Afterwards, the writer examined the bore with a Hawkeye bore scope. There was a uniform, grey film down the entire barrel, with some small, intermittent lead build-up at and just forward of the throat.
Some bore-cleaning rope products feature separate, detachable bronze brush and bore mop segments. This allows more usage options (e.g. mop only), and makes it easier to clean the brush elements:
A new bore-snake was then wet with solvent and pulled through the bore. The Hawkeye revealed that the grey fouling was gone, and much of the visible fouling at the throat was reduced. However, nine more passes with the bore-snake, checking after each with the Hawkeye, revealed no further improvement in cleaning. The writer then cleaned with two wet patches, observed, then one stroke of a new, wet bronze brush, and one wet patch to clean out residue.
The Hawkeye showed a significant reduction in fouling at the throat; it was virtually gone. A second pass with a wet bronze brush and a wet patch removed the remaining fouling. Scrubbing the bore further, checking to see how much fouling was removed, revealed no significant improvement. The reason for this test was to learn what’s needed to get (and keep) this Anschutz clean with minimal cleaning rod use — and thus, minimal risk of bore damage/wear. Leaving fouling in the bore promotes corrosion over time.
Obviously, this applies to a nice, smooth rimfire match barrel, using good, well lubed ammo. It doesn’t apply directly to the use of copper-jacketed bullets, which leave a stubborn fouling all their own. However, it does suggest that while the bore-snake can be helpful and a useful field-expedient, to truly clean a rifle barrel one will still need a good quality rod, bronze brush and solvents. [Editor: Add a good-fitting cleaning rod bore guide.]
SO, WHAT ABOUT BORE SNAKES FOR BARREL BREAK-IN?
The goal of barrel break-in is to fire each shot through a clean barrel, preventing copper buildup and allowing the bullets their best chance at burnishing sharp edges. Thus, it seems this purpose would be best served by one’s usual rods, brushes and rod guides.
The 2023 Berger Southwest Nationals (SWN) will be held in Phoenix on February 15-19, 2023. After National Championships, this is the biggest event of the year for F-Class and Palma shooters. But the winds at the Ben Avery Range in Phoenix can be notoriously unpredictable this time of year. It can be calm and consistent one afternoon, then very breezy and switchy the next.
If you want to succeed at the Berger SWN event, you need to be a good wind-reader. One missed call could mean a 6 instead of a 10 and that can make a difference in final standings. The book featured here will help you improve your wind-reading skills. The Wind Book for Rifle Shooters is definitely a good investment for any serious long-range rifle competitor.
“The pessimist complains about the wind; the optimist expects it to change; the realist adjusts the sails.” — William Arthur Ward
Readers often ask us: “Is there a decent, easy-to-comprehend book that can help my wind-reading?” Many of our Forum members have recommended The Wind Book for Rifle Shooters by Linda Miller and Keith Cunningham.
Updated Edition Released in May 2020
A NEW hardback edition of The Wind Book for Rifle Shooters was released in May 2020. This 144-page book, first published in 2007, is a great resource. But you don’t have to take our word for it. If you click this link, you can read book excerpts and decide for yourself. When the Amazon page opens, click the book cover photo (labeled “Look Inside”) and another screen will appear. This lets you preview chapters from the first edition, and view some illustrations. Along with the new hardback edition ($22.99), Amazon offers a Kindle (eBook) edition for $14.99.
Other books cover wind reading in a broader discussion of ballistics or long-range shooting, such as Applied Ballistics for Long-Range Shooting by Bryan Litz. But the Miller & Cunningham book is ALL about wind reading from cover to cover, and that is its strength. The book focuses on real world skills that can help you accurately gauge wind angle, wind velocity, and wind cycles.
All other factors being equal, it is your ability to read the wind that will make the most difference in your shooting accuracy. The better you understand the behavior of the wind, the better you will understand the behavior of your bullet. — The Wind Book for Rifle Shooters
The Wind Book for Rifle Shooters covers techniques and tactics used by expert wind-readers. There are numerous charts and illustrations. The authors show you how to put together a simple wind-reading “toolbox” for calculating wind speed, direction, deflection and drift. Then they explain how to use these tools to read flags and mirage, record and interpret your observations, and time your shots to compensate for wind.
I believe this is a must-have book if you are a long-range sport shooter. I compete in F-Class Open and when I first purchased this book and read it from cover to cover, it helped me understand wind reading and making accurate scope corrections. Buy this book, read it, put into practice what it tells you, you will not be disappointed. — P. Janzso
If you have one book for wind reading, this should be it. Whether you’re a novice or experienced wind shooter this book has something for you. It covers how to get wind speed and direction from flags, mirage, and natural phenomenon. In my opinion this is the best book for learning to read wind speed and direction. — Muddler
This article is copyright 2023 AccurateShooter.com. Publication on another site is a willful violation of copyright law.
The 2023 Western Hunting and Conservation EXPO opens today at the Salt Palace Convention Center in Salt Lake City, Utah. The Western Hunting and Conservation Expo is the largest hunting convention open to the public in the Western USA. The EXPO features daily seminars, waterfowl and elk calling championships, auctions, drawings and more. Exhibit halls open 10:00 AM to 7:00 PM, Thursday through Saturday and 10:00 AM to 4:00 PM on Sunday. A partnership between the Mule Deer Foundation, Sportsmen for Fish and Wildlife, and Utah Office of Tourism. With over 400 hunting and outdoor business vendors, this year’s event should attract over 55,000 attendees.
CLICK HERE to register for the EXPO. Various packages are offered. There is a basic 4-day Hall Pass, and other deluxe packages including banquets and entertainment.
New Elite Hunter Bullets from Berger Berger Bullets will attend the 2023 Western Hunting EXPO this year in Utah. Berger’s hunting bullets — VLD Hunting, Elite Hunter, and Classic Hunter –are designed for controlled expansion and extreme hydrostatic shock at both short- and long-range distances. These bullets are available for handloaders, and these bullet options are also offered used in quality factory ammo.
New for 2023, Berger has expanded its successful Elite Hunter ammunition with the following offerings: 6mm Creedmoor 108 Grain Elite Hunter, 6.5 Creedmoor 140 Grain Elite Hunter, 6.5 PRC 140 Grain Elite Hunter, and 300 PRC 245 Grain Elite Hunter.
This article, as published in AccurateShooter.com, contains copyrighted content. It shall not be republished in whole or in part without advanced permission in writing. The act of republishing constitutes legal consent to licensing fees.
Back by popular demand, Hornady is now running its 2023 Get Loaded® promotion. With this promo you can get up to 500 FREE BULLETS with qualifying purchases of Hornady reloading products.
The 2023 Get Loaded program begins on February 1, 2023 and continues through December 31, 2023. Customers who purchase from the qualifying Hornady lineup of reloading presses and reloading tools will receive free bullets after submitting official redemption forms. Depending on the products purchased, customers can get 500 or 100 free bullets, valued up to $234.33.
For centerfire rounds, consistent ignition (and low ES/SD) all begins with the primer in the base of the cartridge. When the firing pin strikes the primer, it sets off a small flame/spark which lights the powder in the case. Energy from that burning powder pushes the bullet out of the cartridge, down the barrel, and out to the target. It’s fair to say, then, that accurate shooting all begins with the primer.
When seating primers, consistency counts. You want to make sure the primer is fully seated in the primer pocket in the base of the case. You want to ensure a slight bit of crush (flattening) for proper seating, and it doesn’t hurt to have very consistent primer seating depths. That’s why guys use tools to uniform their primer pockets.
Here’s a tool that lets you measure the consistency of primer seating depths. Forum members have reported it works really well — measurements are quick and repeatable. Will this tool lower your ES/SD or improve accuracy? That’s hard to say. However, it will definitely help you detect when a primer in a loaded round is seated too high or too low — that’s important. In addition, it can give you precise measurements for comparison testing with different types of primers.
Accuracy One Precision Primer Gauge
The Accuracy One Precision Primer Gauge will precisely measure primer pocket depth and the depth of seated primers in relationship to the face of the case head. The Precision Primer Gauge can also be used to measure the thickness of an unseated primer, allowing you to calculate the optimum seating depth for the particular primers and cases you are loading.
Precision Primer Gauge Features:
Digital Indicator with 0.01mm/0.0005″ resolution
Gauge Body is machined from 303 stainless steel
Small Primer Stem and Large Primer Stem
Both .223 Rem and .308 Win zeroing block
Magnum and .338 Lapua zeroing block
Case Compatibility: The Precision Primer Gauge works with 300 Win. Mag case head diameter (.532”) cartridges, .308 Win. case head diameter (.473”) cartridges, and .223 Rem case head diameter (.378”) cartridges using either large or small primers.
Precision Primer Gauge Pricing:
PPG Without Indicator: $150.00
PPG With Indicator: $210.00
PPG Main Body Only: $55.00
Gauge Stand: $55.00
Phone Orders: Call (814) 684-5322
How to Order the Precision Primer Gauge:
The Precision Primer Gauge can be ordered via phone, email, or postal mail. CLICK HERE for more info.
Assembly Tips: Nylon screw is provided for securing the gauge body to the indicator. The contact point of the indicator must be removed to provide proper function. Also, please note that the standard gauge body is not compatible with cartridges that share the .338 Lapua case head diameter unless the diameter of the magnum step is machined to .595” to accept the larger diameter case head. This modification of the gauge body is available upon request.
Product Tip from EdLongRange. We welcome reader submissions.
The Lapua Monarch Cup 2023 schedule has been finalized. The Lapua Monarch Cup (LMC) is a series of smallbore rifle silhouette matches held in Canada, the United States, and Mexico. Following an abbreviated schedule in 2022, this year’s LMC event features a competition in each country.
For the silhouette shooting community, we predict the Lapua Monarch Cup will be a highly popular event this year. Here are the locations and dates for 2023 Monarch Cup Matches:
1st Match – Canadian Metallic Silhouette National Championship
— Bull River Shooters Association, Cranbrook, British Columbia, Canada
— June 25-27, 2023
2nd Match – NRA Smallbore Rifle Silhouette National Championship
— NRA Whittington Center, Raton, NM, USA
— July 17-19, 2023
3rd Match – Lapua Monarch Cup
— Club De Tiro Saltillo Safari, Saltillo, Coahuila, Mexico
— Oct. 21-22, 2023
Competitors earn scores from each match within their respective classification (Master, AAA, AA, & A), giving all shooters an opportunity for $25,000 in cash prizes to be distributed within the three countries. The Monarch Cup has become one of the most prestigious smallbore silhouette match in the world. Monarch Cup Director Daniel Salazar Stated: “We are focused on taking this shooting sport to a new level, with new scoring system and new awarding system”.
Adam Braverman, V.P. Sales & Marketing with Capstone Precision Group added: “Lapua is very excited to see this match series take place in 2023. We are happy that we were able to include Canada in the 2023 version. The Lapua Monarch Cup is a world class match made even better with Canada’s inclusion.”
Lapua Monarch Cup Board Members are Erich Mietenkorte, Daniel Salazar, Jason Marsh, Alfredo (Pepe) Valdes, and newly appointed Chris Cawthorne. Adam Braverman serves as an advisor. For registration information and the full details on the Lapua Monarch Cup, visit www.lapuamonarchcup.com
For information on the newly created North American Silhouette Shooting Association (NASSA), visit nassasilhouette.org
About Capstone Precision Group
Capstone Precision Group produces Berger Bullets and Ammunition in Mesa, AZ, and is the exclusive distributor of Lapua Components and Ammunition, Vihtavuori Powders and SK Rimfire. Capstone Precision Group is a Part of Nammo Group. For more information, visit Capstonepg.com.
The Coriolis Effect comes into play with extreme long-range shots like this (2100 yards at Raton, New Mexico). The rotation of the earth actually moves the target a small distance (in space) during the long duration of the bullet’s flight.
When you’re out at the range, the Earth seems very stable. But it is actually a big sphere zooming through space while spinning around its axis, one complete turn every 24 hours. The rotation of the earth can create problems for extreme long-range shooters. During extended bullet flight times, the rotation of the planet causes an apparent deflection of the bullet path over very long distances. This is the ballistics manifestation of the Coriolis Effect.
Bryan Litz of Applied Ballistics discusses explains the Coriolis Effect in his Ballistics Books and Seminars. Bryan notes that Coriolis is “a very subtle effect. People like to make more of it than it is because it seems mysterious.” In most common shooting situations inside 1K, Coriolis is not important. At 1000 yards, the Effect represents less than one click (for most cartridge types). Even well past 1000 yards, in windy conditions, the Coriolis Effect may well be “lost in the noise”. But in very calm conditions, when shooting at extreme ranges, Bryan says you can benefit from adjusting your ballistics solution for Coriolis.
Bryan explains: “The Coriolis Effect… has to do with the spin of the earth. You are basically shooting from one point to another on a rotating sphere, in an inertial reference frame. The consequence of that is that, if the flight time of the bullet gets significantly long, the bullet can have an apparent drift from its intended target. The amount [of apparent drift] is very small — it depends on your latitude and azimuth of fire on the planet.”
Coriolis is a very subtle effect. With typical bullet BCs and velocities, you must get to at least 1000 yards before Coriolis amounts to even one click. Accordingly, Bryan advises: “Coriolis Effect is NOT something to think about on moving targets, it is NOT something to think about in high, uncertain wind environments because there are variables that are dominating your uncertainty picture, and the Coriolis will distract you more than the correction is worth.”
“Where you could think about Coriolis, and have it be a major impact on your hit percentage, is if you are shooting at extended range, at relatively small targets, in low-wind conditions. Where you know your muzzle velocity and BC very well, [and there are] pristine conditions, that’s where you’re going to see Coriolis creep in. You’ll receive more refinement and accuracy in your ballistics solutions if you account for Coriolis on those types of shots. But in most practical long-range shooting situations, Coriolis is NOT important. What IS important is to understand is when you should think about it and when you shouldn’t, i.e. when applying it will matter and when it won’t.”
So what does a “worn-out” barrel really look like? Tom Myers answered that question when he removed a 6.5-284 barrel and cut it down the middle to reveal throat wear. As you can see, there is a gap of about 5mm before the lands begin and you can see how the lands have thinned at the ends. (Note: even in a new barrel, there would be a section of freebore, so not all the 5mm gap represents wear.) There is actually just about 2mm of lands worn away. Tom notes: “Since I started out, I’ve chased the lands, moving out the seating depth .086″ (2.18 mm). I always seat to touch. My final touch dimension was 2.440″ with a Stoney Point .26 cal collet.”
Except for the 2mm of wear, the rifling otherwise looks decent, suggesting that setting back and rechambering this barrel could extend its useful life. Tom reports: “This was something I just thought I’d share if anyone was interested. I recently had to re-barrel my favorite prone rifle after its scores at 1,000 started to slip. I only ever shot Sierra 142gr MatchKings with VV N165 out of this barrel. It is a Hart and of course is button-rifled. I documented every round through the gun and got 2,300 over four years. Since I have the facilities, I used wire EDM (Electro Discharge Machining) to section the shot-out barrel in half. It was in amazingly good shape upon close inspection.”
Tom could have had this barrel set back, but he observed, “Lately I have had to increase powder charge to maintain 2,950 fps muzzle velocity. So to set it back would have only increased that problem. [And] I had a brand new 30″ Krieger all ready to screw on. I figured it was unlikely I’d get another full season on the old barrel, so I took it off.”
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Sportsman’s WH — Gun Sale + $100 Smith & Wesson REBATE
2. Midsouth — LEE Breechlock Challenger Press Kit, $144.99
⏺ Heck of a deal on a good press and complete reloading system
For under $150 you can get pretty much everything you need to reload, except dies. This LEE Breech Lock Challenger Kit includes Press, Powder Dispenser, Scale, Hand Primer Tool, Funnel, Chamfer Tool, Primer pocket tool, and more. We like the press — the handle is adjustable and the primer-catching system sends spent primers into a receptacle for no mess cleanup. This $144.99 LEE Kit comes complete with the Breechlock Quick Change die system. If you are looking to get started in handloading, or want a back-up second press with accessories, this is a great deal.
Shooting steel is fun — you get instant gratification from hearing the “clang” and seeing the gong swing. Shooting steel is also good practice for PRS/NRL events and ground-hog matches. Right now, you can get some great deals on quality AR500 steel targets. These Dragon Target Gongs start at just $12.99 for a 4″-diameter, 3/8″-thick gong. Larger 6″, 8″, 10″, and 12″ gongs are offered in 3/8″ and 1/2″ thicknesses, and a 3-pack of 8″ gongs is available. A 6″-diameter gong is $18.99 (3/8″ thick) or $23.99 (1/2″ thick). The largest 12″-diameter gong in the heavy 1/2″ thickness is $57.99. NOTE: All these Dragon gongs have a center hole allowing more hanging options.
⏺ Complete AR-15 rifle for less than you might pay for assembled upper
You can’t beat this price for a complete AR-15 — $399.99 from KYGUNCO with Free Shipping. You could easily pay MORE for an assembled upper alone. The Radical Firearms RPR AR-15 rifle features MIL-STD upper and lower receivers along with 15″ RPR rail system. The 16″ 1:7″-twist barrel is 4140 Chrome Moly Vanadium. The lower is forged 7075 T6 aluminum with Type III anodizing. The buttstock is adjustable and there is a long rail on the top of the aluminum forearm for mounting optics and accessories.
5. Palmetto SA — CCI 9mm 115gr FMJ 1000 Rounds, $299.99
⏺ Quality, reliable CCI 9mm ammo, 1K case works out to $15 for 50 rounds
This is reliable, made-in-USA 9mm ammo, with good brass and quality CCI FMJ bullets. The $299.99 case price works out to just $15.00 per 50 rounds — a great value. This isn’t much more expensive than remanufactured 9mm ammo, and you have the assurance of NEW brass and major brand quality control. Note: This is a loose pack with all 1000 rounds in a single large, heavy-duty box.
6. Powder Valley — 500 Sierra 9mm Bullets with Can, $99.99
⏺ Great price on 9mm bullets with bonus Sierra Ammo Can
A 500-ct can of Sierra 9mm 115gr FMJ bullets is on sale now for $99.99 at Powder Valley Inc.. You get 500 FMJ bullets PLUS a sturdy polymer ammo can at a $50 savings off the normal price. Act soon as this $50 savings ends at 11:59 pm on Friday 2/03/23, or while supplies last. Replenish your 9mm bullet stock and take advantage of this Sierra Bullets + Ammo Can Sale.
7. Midsouth — A-Zoom Snap Cap Sets, $7.15 and up
⏺ Snap Caps for dry-fire training — big selection of cartridge types
All shooters can benefit from dry-fire training. And for that you definitely need Snap Caps. A-Zoom offers a wide range of Snap Cap Kits for rimfire and centerfire rifles and pistols. There is even a jumbo Snap Cap for 12ga shotguns. For semi-auto pistols we recommend the orange StrikerCaps ($7.15 2-pack). These stay in place in the chamber — just rack the slide to reset the trigger. For a large pistol collection, try the $21.96 Pistol Variety Pack with five different cartridge types: .22 LR, .380 ACP, 9mm Luger, .40 S&W, .45 ACP. There’s also a $31.37 Military/LE Variety Pack with 9mm Luger, .40 S&W, .45 ACP, .223 Rem, .308 Win, and 12 Gauge shotshell.
8. Amazon — Walkie Talkies with LED Flashlight, $23.99
⏺ Popular 22 Ch FRS radio set with built-in flashlights
Campers, hunters, and hikers can all use this budget-priced MOICO Walkie-Talkie Set, now just $23.99 on Amazon. These offer 22 FRS channels, with a max 5 mile range (in open country). These work well when communicating between the shooting line and target pits downrange. One great feature is a built-in-LED flashlight — making these Walkie-Talkies great for camping and night-time use.
9. Amazon — Real Avid 19-in-1 Multi-Tool, $39.99
⏺ Versatile Multi-Tool with great features for gun owners
We’re big fans of multi-tools and this 19-in-1 Real Avid Multi-Tool is one of the best for gun guys. This compact 19-in-1 handgun multi-tool is a “must have” for any handgun owner. This tool can handle a multitude of tasks — e.g. changing grips, mounting accessories, field disassembly, adjusting laser sights, and even gunsmithing repairs. This tool does it all.
10. Amazon — Field Dressing Kit, $69.97
⏺ Must-have kit for game hunters — very useful
For the hunters out there, here’s a nice kit to prepare game meat. The versatile Knine Outdoors Field Dressing Kit offers a great selection of tools for a low price. This very complete Dressing Kit includes: 12″ Boning Knife, 9-1/2″ Gut-Hook Skinner, 8-1/2″ Hawkbill blade knife, 8-1/2″ Caping Knife, 12″ Gut-Hook Butcher Axe, 10-1/2″ Skinning Cleaver, 8-1/2″ Bone Saw, Ribcage Spreader (7″ to 12″), 9-1/4″ Game Shear, 11-7/8″ x 7-7/8″ Cutting Board, Knife and Shear Sharpener, and Cleaning Gloves.
11. AAF Nation — T-Shirt or Hoodie, $23.95 or $39.95
⏺ Popular hoodie and/or shirt with great message for older shooters
Let’s face it, many of us are not so young anymore… but we still can shoot! That’s the message of these clothing items. Against a background of a bullseye target, the illustration reads: “Too old to fight, too slow to run, but I can still shoot pretty darn good.” Choose either a hoodie version for $39.95, a regular T-shirt for $23.95, or long sleeve shirt for $29.95. Purchasers report the items are sized properly. One hoodie buyer posted: “This hoodie is warm and comfortable. It is well-made and has a good print job!”
On our main Accurateshooter.com website, you’ll find a comprehensive review of the STM system for cleaning cartridge brass with stainless media. To clean brass with stainless media, start with five pounds of small stainless pins sold by StainlessTumblingMedia.com. Place these along with a gallon of water, a little liquid cleaner, and two pounds of cartridge brass in a rotary tumbler, and run the machine for one to four hours.
Forum Member Tests STM System
Our reviewer, Forum member Jason Koplin, purchased the STM media and a new Thumler’s Tumbler. He then tested the STM cleaning procedure on his own brass, including some extremely dirty and tarnished “range pick-up” brass. Jason was thoroughly impressed with how well the STM process worked — as you can see from the “before and after” photos below. Brass which looked like it was ready for the scrap heap was restored to “like-new” appearance. Check it out:
Works Great on Both Rifle Brass and Pistol Brass
The process works equally well on both rifle brass and pistol brass (see below). Jason observed that one surprise benefit of the STM cleaning procedure is a big reduction in noise in his reloading room. Jason said the water-filled rotary tumbler was much quieter than his vibratory tumblers.
You’ll want to read Jason’s full review which shows more before and after images. The full article features a “how-to” video created by Forum member Cory Dickerson, the young man who pioneered the stainless tumbling process and founded STM. The video shows how to load brass, media, and cleaner solutions into the tumbler, and how to separate media from brass once the tumbling is done.
Bore-snakes are very useful for some applications (primarily a hasty, interim wipe-down). In [my] experience they cannot replace a thorough cleaning with a proper rod and brushes. While the experiment cited here involves rimfire, it may help illustrate. Several years ago, the writer used his new, personal Anschutz to investigate the bore-snake issue. It had been fired ~350 rds with match ammo and had had 3 typical rod/brush cleanings. 
When you’re out at the range, the Earth seems very stable. But it is actually a big sphere zooming through space while spinning around its axis, one complete turn every 24 hours. The rotation of the earth can create problems for extreme long-range shooters. During extended bullet flight times, the rotation of the planet causes an apparent deflection of the bullet path over very long distances. This is the ballistics manifestation of the 
So what does a “worn-out” barrel really look like? Tom Myers answered that question when he removed a 6.5-284 barrel and cut it down the middle to reveal throat wear. As you can see, there is a gap of about 5mm before the lands begin and you can see how the lands have thinned at the ends. (Note: even in a new barrel, there would be a section of freebore, so not all the 5mm gap represents wear.) There is actually just about 2mm of lands worn away. Tom notes: “Since I started out, I’ve chased the lands, moving out the seating depth .086″ (2.18 mm). I always seat to touch. My final touch dimension was 2.440″ with a Stoney Point .26 cal collet.”
On our main 
