Top to bottom – Remington firing pin assembly with ISS, Tubb SpeedLock alloy-composite system without ISS (current versions have dual, opposite-wound springs), and Remington short action firing pin assembly without ISS.
The U.S. Army Marksmanship Unit regularly publishes technical articles on the USAMU Facebook page. One informative USAMU article covered mechanical issues and related ignition irregularities that can cause vertical fliers even with good ammunition in an otherwise excellent rifle. We highly recommend you read this article, which offers some important tech tips.
Vertical Dispersion: Mechanical/Ignition Issues?
Poor or inconsistent ignition has long been known to be one of the “usual suspects” when one encounters vertical fliers that just shouldn’t be there. By having a sense of some of the basic principles involved, and a few basic areas to check, the shooter may avoid colsiderable frustration, not to mention time, expensive loading components and barrel wear.
Is your well-built rifle of high-quality components plagued with vertical fliers across more than 1-3 handload combinations? Consider the bedding, crown and scope/sight mounts. Are they correct? If so, then you might check for ignition issues before boldly undertaking an extensive, expensive, and quite possibly fruitless quest for the “magic handload”.
SEEING IS BELIEVING: While the author had been aware for many years that poor ignition should be considered and ruled out when dealing with vertical fliers in an otherwise-excellent rifle, actually seeing the problem and its almost instantaneous cure really drove the lesson home.
He was working with a “dot” rifle – a .22 LR match rifle that really stacked bullets into little piles at 50 yards and beyond. With one lot of ELEY Tenex, it produced consistent “bughole” groups at 50, but with another, selected lot of Tenex, similar groups were regularly ruined by single, vertical fliers that did not appear in other rifles. Rather than spending days burning up expensive, select ammunition looking for “magic lots”, he contacted a well-respected rimfire gunsmith and explained the situation.
Without so much as batting an eye, the highly-experienced ‘smith tore into the rifle’s action, and quickly found the cause(s) of the problem. He discovered a demonstrably weak firing pin spring, plus a chip out of the face of the firing pin where it contacted the cartridge rim.
After replacing and tuning the offending parts, the rifle immediately began shooting tiny, bughole groups with the previously “unacceptable” lot of Tenex. Centerfire rifles can also benefit from ensuring positive, consistent ignition. A wise riflesmith is literally worth his weight in gold!
So, what are some issues we as shooters can inspect in our rifles to help determine if ignition woes could be part of our problem? At the club level, ask yourself if that “experienced” Remington, Winchester 70, or even Springfield-based match bolt gun you’re using is still running its’ original 40-80 year-old factory striker spring? If so, a new replacement is cheap insurance against current or future problems. (And BTW, it might be best to stick to the normal, factory-spec spring weight. A super-powerful spring can cause vertical, just as a weak one one can.) Along with that, a routine check for proper firing-pin protrusion is a quick preventive measure that can rule out potential issues.
Other areas to consider are the centering and consistency of the firing pin’s operation in the bolt. Admittedly, with the increasing use of precision-machined custom actions, this is becoming less an issue every day. Below is the firing pin assembly from a custom BAT action:
However, particularly with factory actions, a very quick and easy check is to remove the bolt, let the firing pin go forward, and look at the firing pin tip through the firing pin hole. Is the tip off-center in the hole, and possibly striking it as it moves forward? Is the hole out-of-round or burred from being struck repeatedly? If so, a trip to the riflesmith is likely in order.
Similarly, machining issues in the bolt/firing pin system can lead to rough and erratic firing pin movement, in which the firing pin drags against an internal surface of the bolt. In high-quality rifles these issues are relatively rare, but not unheard-of, and it takes mere minutes to rule them out. It may be worthwhile to remove the cocking piece/firing pin/spring assembly and look for any unusual gouges, dings, peening, burrs or signs of abnormal wear.
This task is especially easy with Winchester 70s, Springfields, and the similar Mauser 98s, involving little more than the push of a button and unscrewing the cocking piece assembly. This is just one of the many reasons these tried-and-true actions have earned such a loyal following in the field, among hunters who must maintain their rifles away from a shop.
Particularly with older rifles, watch for and remove excess grease (or even Cosmoline!) from both the firing pin assembly and inside the bolt. This can help improve firing pin speed and consistency. Other bolt-action designs may need a take-down tool or other measures.
As part of this inspection, AFTER ENSURING THE RIFLE IS UNLOADED, slowly cock the rifle, dry-fire, and repeat several times. Listen carefully near the action for inconsistency in the sounds it generates. Does the striker falling make the same sound each time? Do you hear or feel grinding upon operation? If so, where?
Be sure to check the operation of the cocking piece (bolt shroud), firing pin within the bolt shroud, the cocking piece cam and the rear of the bolt body where the cocking piece cam operates. As with our examination for abnormal wear marks discussed above, look for marks indicating roughness or a possible need for light polishing. Then, clean and lightly grease the bearing surfaces while you’re at it.
Remington 700 bolt shroud and cocking cam
These are relatively easy checks that shooters can undertake to perform a preliminary inspection on their own. Other mechanical issues can also cause ignition issues, chiefly centered around the action of the trigger, sear and sear spring. If these are suspected, a trip to an experienced, qualified riflesmith for diagnosis is recommended. We hope you find this information helpful! Join us again next week, and in the meantime, enjoy the shooting sports safely!
When you want a firearm for home defense instantly available, you don’t necessarily want it buried in a large gun safe in a remote section of your house. There are reasons you may want a rifle, pistol, or shotgun ready to be deployed quickly. One solution for this is the “hidden in plain sight” option. Using common household furniture or house features (such as vents and mirrors), you can stash a firearms where it can be quickly accessed, but no unwelcome visitor will suspect it is stored. This article presents some popular gun storage options.
Virginia-based Tactical Walls is a leader is specialized gun storage/concealment systems. This company offers a variety of USA-made furniture/decorative options for gun storage. There are mirror assemblies, sliding wooden flags, tables with hidden storage, bookcases, shelving units, and more. The General Manager of Tactical Walls is Dennis DeMille, formerly GM of Creedmoor Sports, and a talented marksman.
Dennis tells us: “Tactical Walls was the pioneer in concealing firearms in plain sight”. He says this company has great creativity and impressive production capabilities. View all Tactical Walls concealment gun storage options at TacticalWalls.com.
Fine Firearms Furniture with Slide-Open Table Top
Here’s something that will teach unwanted guests some “table manners”. We’ve seen handguns hidden in books, and stowed behind faux baseboard vents, but this hand-crafted, slide-open table takes the cake. We doubt that anyone could sit down at this table and suspect that a shotgun, scoped rifle, two pistols and a knife were stored securely inside. There’s an arsenal hiding in there!
To access the guns under the sliding table-top, first you flip down a wood trap-door on the side. That exposes a key-lock which unlatches the interleaved left and right table segments. These slide open horizontally on metal tracks, exposing the full arsenal underneath. This “table vault” is a very clever design, built with fine craftsmanship. You can purchase this table from the maker for $1799.00.
Hidden in Plain Sight — Guide Gear Vent Pistol Locker
This clever “imposter vent” should fool any unwanted visitors. This Guide Gear Hide-A-Gun vent storage unit is just $34.99 on Amazon. NOTE: This will require installation in the wall, with attachment to studs.
Decorative Storage — Patriot Flag Concealment Unit
This handsome triangular wood box has hidden storage for a firearm and/or valuables. It is $39.95 at MidwayUSA or $49.99 on Amazon. You may want to bolt this down to a shelf for extra security.
Precision Rifle Challenge on Shooting USA This Week
This week, Shooting USA TV features a show that should interest PRS/NRL fans, tactical marksmen, and long range hunters. Run in Utah’s backcountry, the Hornady Precision Rifle Challenge is a unique long range competition with serious wind and elevation changes. This isn’t a typical PRS Pro Series match by any means. Participants in this challenging Precision Rifle match encounter tough conditions not typically seen in other tactical matches. The match runs in summer in Utah, just across the state line from Evanston, Wyoming. Watch the show 11/18/20 on the Outdoor Channel.
This video is great — lots of equipment closeups, stage set-ups, plus drone footage of range.
At this year’s match, held July 10-11, 2020, Clay Blackketter took first place overall, Doug Koenig won the Production Division, and Travis Gibson won the Tactical Division using a .308 Win. All three men are members of Team Hornady. This was a big match with 177 competitors at Hornady’s private 250,000 acre ranch property outside of Evanston, Wyoming.
Shooting USA will air Wednesday, November 18, 2020, at 9:00 PM Eastern (8:00 PM Central) on the Outdoor Channel. If you miss that, it runs again on Thursday afternoon. Look for Shooting USA on the Outdoor Channel. In addition, you can watch all episodes of Shooting USA on the VIMEO channel by subscription. Each episode is just $0.99, about 1/10th what a movie ticket costs these days.
Browning M2 Heavy Machine Gun — History’s Guns
In addition to the Precision Rifle challenge, this week’s Shooting USA episode also showcases the Browning M2 .50 Caliber Heavy Machine Gun. The .50 Cal M2 machine gun was designed by John Moses Browning and went into military service in 1933. Its design is similar to Browning’s earlier M1919 Browning machine gun, which was chambered for the .30-06 cartridge. The M2 uses the much larger and more powerful .50 BMG cartridge, which derives its name from the gun (BMG stands for “Browning Machine Gun”). It has been referred to as “Ma Deuce”, in reference to its M2 nomenclature.
With a half-inch diameter bullet weighing 750 grains, the .50 BMG cartridge is effective beyond a mile in attacking light armored vehicles. And the M2 Browning has served for nearly a century, in the skies, on the ground, and at sea. Updated versions of the Ma Deuce are still being produced and deployed today.
These days, online gun Auctions and Classifieds attract more attention than ever. With so many folks accessing the internet daily, many gun owners find it easier to sell their firearms online rather than in the local gun store. Online selling opens up a much larger audience. With over 53,000 members in the AccurateShooter Forum, we have a very active gun Classifieds area. And then of course, there are the big dogs — Gunbroker and GunsAmerica. You’ll find tens of thousands of guns for sale on those big sites.
Before selling your stuff online, you should survey the major online sales and auction sites, comparing their fees and features. The costs are NOT all the same. For example, though you can list an item on Gunbroker for free, if the gun sells you may end up paying a LOT of money. Confirm this with the Gunbroker FEE Calculator. Using Gunbroker’s Fee Calculator we determined that, for a $2500.00 gun, the seller will pay $93.75 in fees! Yes, that’s for a single sale.
That’s why many sellers prefer to list their rifles on Benchrest.com, or on the AccurateShooter.com FORUM Classifieds. Currently, basic Accurate Forum members get three (3) free adverts in a 12-month period, while Gold and Silver members get unlimited classifieds for 12 months. A $25 Silver membership is less than you’d pay to sell one single $550 item on Gunbroker ($25.50 fee).
SEVEN TIPS for Selling Your Gear Online
1. Include Good, Sharp Photos: A custom rifle or expensive optic will sell two to three times as quickly, at a higher price, if you include good sharp photos. We can’t over-emphasize the importance of good photos. For all products, show multiple angles, and include the original boxes if you still have them. For a rifle, include detail shots as well as a photo of the complete gun.
2. Resize Your Photos Before Posting: Half of users will probably be viewing your ads with a smartphone. So you don’t need huge photos. We recommend you size your photos down to 1000 pixels wide. This will make uploads more efficient and ensure the Forum server can handle the file sizes.
3. Be Fair and Complete in Your Description: Buyers appreciate honesty and thoroughness in product descriptions. Potential buyers want details. For a rifle, list the gunsmith, barrel-maker, round count, and provide the specifications. If the rifle has a winning competition history, say so. Always highlight the positives in your description, but you should disclose significant flaws. A buyer will be more willing to purchase if he thinks the seller is 100% honest.
4. Don’t Forget Contact Info: We’re amazed by how many adverts omit key contact info. In a forum classified ad, include a first name, e.g. “Ask for Dan.” We also suggest you list your residence city and state. Some buyers will prefer to buy from a seller in their home state. When communicating with a buyer, provide your phone number and email address. We recommend that all buyers and sellers actually talk live on the phone before concluding high-value deals.
5. Make the Price Attractive: Buyers, everywhere, are looking for good deals. If you want your item to move quickly, set the price accordingly and don’t expect top dollar. Check comparable listings and then discount by 10-15% if you want the item to move fast.
6. Include a Call to Action: Advertisements can be twice as effective if they include a “Call to Action”, i.e. a statement that directly inspires the potential buyer to respond. Sample calls to action are: “Free Shipping — today only.” Or, you can use a time limit: “Special Sale Price good ’til the end of the month”.
7. Always Follow ALL Applicable Laws: Even in states where private face-to-face gun sales are allowed, we recommend ALWAYS using an FFL for firearms transfers. This will protect YOU the seller. In addition, do your homework. Don’t sell to a buyer in a city or state (such as California) state or city where the particular firearm (such as an AR15) may be restricted
Classified Advert vs. Auctions For benchrest, F-Class, Silhouette, Tactical or High Power rifles, you may get the best results posting a For Sale ad on a Forum that caters to the right discipline. You want your ad to reach the right audience. On the other hand, a GunBroker.com auction will have tens of thousands of potential buyers. Realistically, however, if you price your rig attractively, it should sell quickly in a Forum Classified Advert. Plus with conventional Classifieds, you can sell immediately — you don’t have to wait for the auction to end. For scopes and reloading equipment (but not firearms, actions, barrels etc.), also consider eBay, which still allows many gun-related items.
We first ran this article in 2012, and it was very well received. Since then, many Forum members have requested an explanation of MILS and mildots, so we decided to run this feature again…
In this NSSF Video, Ryan Cleckner, a former Sniper Instructor for the 1st Ranger Battalion, defines the term “MilliRadian” (Milrad) and explains how you can use a mildot-type scope to range the distance to your target. It’s pretty simple, once you understand the angular subtension for the reticle stadia dots/lines. Cleckner also explains how you can use the milrad-based reticle markings in your scope for elevation hold-overs and windage hold-offs.
Even if you normally shoot at known distances, the hold-off capability of milrad-reticle scopes can help you shoot more accurately in rapidly-changing wind conditions. And, when you must engage multiple targets quickly, you can use the reticle’s mil markings to move quickly from one target distance to another without having to spin your elevation turrets up and down.
WEB RESOURCES: If you want to learn more about using Milliradians and Mildot scopes, we suggest the excellent Mil-dot.com User Guide. This covers the basics you need to know, with clear illustrations. Also informative is The Truth about Mil Dots by Michael Haugen. Mr. Haugen begins with basic definitions: 1 radian = 2 PI; 1 Milliradian (Milrad or ‘Mil’) = 1/1000th of a radian; 1 Milliradian = .0573 degrees.
Earlier this year, CZ introduced a new .22 LR rifle for shooters looking for a PRS/NRL rimfire cross-trainer or a bolt gun for NRL22 competition. This new CZ 457 Long Range Precision (LRP) model features a 20″ fluted barrel with factory-installed muzzle brake. The stock adjusts for length-of-pull and has an adjustable cheekpiece. On top of the action is a +25 MOA Weaver-type rail so you have enough elevation to shoot out to 300 yards and beyond with most scopes. The single-stage trigger is also adjustable. MSRP is over $1200.00 but this rifle is now available for $899.99 at KYGunCo.com.
CZ factory video shows features of CZ 457 LRP:
The LRP’s target stock boast textured grip surfaces and a near-vertical pistol grip. The rear has a “hook” for positions where the shooter will use his non-shooting “off” hand to steady the rear of the rifle when the front is on a bag or support. The rear rail allows quick installation of monopod or bag-rider. There is a very fat, oversized bolt knob. A five-round magazine is standard with 10-rounders availalble.
The height of both the comb (cheekpiece) and buttpad are adjustable. Also the length-of-pull can be adjusted with the four included spacers (351-382 mm).
Trigger: Adjustable
Cheekpiece: Adjustable for Height
Buttpad: Adjustable for Height
LOP: Adjustable with Spacers
Stock: Beech with Soft-touch Finish
Muzzle Brake: Standard
Click Image to see full-screen photo of CZ 457 LRP
We created the above target a decade ago. Since then it has been used by tens of thousands of shooters. It has proven very popular as a load development target, since all your load data fits neatly in the boxes under each target. In fact this target is being employed by both rifle-makers and barrel-makers (including Criterion) to test their products. The target was designed for aiming efficiency. The diamonds have 1/2″ sides and you can align your reticle cross-hairs on the horizontal and vertical lines. It is a clean design that is easy to see even at 200 yards with a 20X scope. When we test, we usually crank in a little elevation, setting the point-of-impact higher, so that our shots fall in the gray circles. That way you leave the red diamonds intact for precise aiming. CLICK HERE to download Load Dev target.
We also use these two targets for load development and precision practice. The circle dot target can also be used for informal rimfire competition at 50 yards.
Right-Click Each Target to Download Printable PDFs.
How to Print Your Targets
Most of us have access to a printer at home or at work. That means you can print your own targets. You’ll find hundreds of free target designs online, including dozens of downloadable targets on our AccurateShooter.com Target Page. If you’re feeling creative, you can design your own target with a computer drawing program such as MS Paint.
Paper Stock Is Important
If you want your self-printed targets to show shots cleanly (and not rip when it gets windy), you should use quality paper stock. We recommend card stock — the kind of thick paper used for business cards. Card stock is available in both 65-lb and 110-lb weights in a variety of colors. We generally print black on white. But you might experiment with bright orange or yellow sheets. Forum Member ShootDots report: “They sell cardstock at Fed-Ex Kinko! I use either Orange or Yellow. That makes it easy to see the bullet holes clearly.” NOTE: Test before you use the 110-lb Cardstock. On some printers, with the heavier 110-lb card stock, you will need to have the paper exit through the rear for a straighter run.
Here are some Target-Printing Tips from our Forum members:
“Staples sells a 67-lb heavy stock that I have settled on. I use the light grey or light blue, either of these are easy on the eyes on bright days. I have used the 110-lb card stock as well and it works fine. It’s just a little easier to print the lighter stuff.” (JBarnwell)
“Cardstock, as mentioned, works great for showing bullet holes as it doesn’t tear or rip like the thin, lightweight 20-lb paper. I’ve never had a problem with cardstock feeding in the printer, just don’t stick too many sheets in there. If I need three targets, I load only three card stock sheets”. (MEMilanuk)
“20-lb bond works pretty well for me if I use a spray adhesive and stick the entire back of the paper’s surface to the backer board.” (Lapua40X)
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Sportsman’s Warehouse — Winchester .22 LR Wildcat, $219.99
⏺ Removable lower receiver, Picatinny rails, good trigger, great price
Here is a fun little semi-auto .22 LR rifle at a crazy low price — $219.99 at Sportsman’s Warehouse. The Winchester Wildcat takes Ruger 10/22 mags, and has some great features, such as field-removable lower receiver, ambidextrous controls, integral Picatinny rails and rear barrel access. Here’s a good video that shows this rifle in action. We think you’ll be impressed. It has a good trigger and shoots well. In many respect the Wildcat beats the Ruger 10/22 while costing considerably less.
The Wildcat comes with a Picatinny top rail for optics or electronic sights. A Picatinny rail on the forearm lets you attach an optional bipod, sling mount or other accessory. The lower receiver assembly is easily removed from the upper assembly by pushing a single button located at the rear of the upper assembly with your finger. No tools are required. The Wildcat accepts a wide range of aftermarket magazines that are compatible with the 10/22.
2. Natchez — Leupold Black Friday Optics Sale, Save up to 30%
⏺ Save Big on Regular and Blemished Leupold Scopes and Optics
The annual Black Friday Sale started early at Natchez Shooter’s Supplies with HUGE savings on regular and blemished Leupold scopes, rangefinders, spotting scopes, and binoculars. You can save 30% or more on blemished items, which still have full factory warranties. For example a “blem” Leupold SX-2 25-60x80mm HD spotter is now $769.99 marked down from $1099.99 — a 30% savings!
3. Sportsman’s Warehouse — AR-15 Rifles from $599.99
⏺ Get your Black Rifle now while you still can
Now that it looks like we will have a new President who has declared his clear intention of banning mag-fed, semi-auto rifles, maybe it’s time to get that AR-15 while you still can. While ARs are flying off the shelves right now, thankfully Sportsman’s Warehouse still has a large inventory of complete .223 Rem/5.56×45 AR-platform rifles in a variety of configurations. Prices start at $599.99.
4. Midsouth Shooters — RCBS Explorer 2 Reloading Kit, $359.99
⏺ Good starter kit, with nice press, powder measure and primer tool
With the shortage of factory ammo in many calibers, more folks than ever are turning to hand-loading. Here is a good RCBS Explorer 2 Kit that will get you started. Along with the Reloader Special 5 Press, you get an excellent Uniflow-III Powder Measure, a digital pocket scale, hand priming tool, Powder Funnel, fold-up hex key set, deburring tool, case loading block and spray case lube. And the kit even includes a Speer #15 Reloading manual, with loading procedures and load data.
5. Brownells — KRG Bravo Chassis Rem 700, $329.99 with Code
⏺ Versatile internal frame stock for PRS or hunting — tan, black, or green
The Kinetic Research Group (KRG) Rem 700 Bravo Chassis is a good dual-purpose choice for PRS and hunting. There is an internal aluminum frame with polymer exterior in Flat Dark Earth, Sako Green, or Black. The stock fits Rem 700 and Rem clone actions, accepts AICS-pattern mags, and is M-LOK compatible. The 2.9-lb KRG Bravo chassis features adjustable cheek riser and length-of-pull, built-in thumb shelf, plus quick-detach sling-swivel and bipod mounts. The KRG Bravo stock costs $349.99 at Brownells. You can also get $20 Off with Brownells code VTJ, lowering the net cost to $329.99.
6. Amazon — Teslong Borescope $39.99 or Rigid Version $79.99
⏺ Teslong borescopes are game-changers — true “must-have” tool
The Teslong digital borescope has been a huge success. This compact, electro-optical, cable-type borescope outputs sharp, high-resolution images and VIDEO to desktop computers and laptops, and many tablets. Check out our Full Teslong Review complete with inside-the-barrel videos. Get the basic version for $39.99 on Amazon or the rigid version Teslong Borescope for $79.99. If you scope your barrels often, you may prefer the rigid version which is easy to insert and rotate.
7. Sportsman’s Warehouse — RCBS Products on Sale
⏺ Great Prices on RCBS tools and products — but act soon
Take advantage of Black Friday early at Sportsman’s Warehouse. A wide selection of RCBS products is on sale now, with significant discounts. Save on presses, powder dispensers, case prep centers, dies, priming tools and more. But act fast — items are selling out quickly. For example the RCBS Rock Chucker press, discounted from $179.99 to $143.99 ($36 off) sold out early this morning.
8. Amazon — Frankford Arsenal Perfect Seat Priming Tool, $69.79
⏺ Precise Depth Control, 12 Shell Holders, Quick-Change, Carry Case
Seating primers to a consistent depth helps deliver enhanced accuracy and low ES/SD. However, most priming systems don’t allow precise depth control. If you’re looking for a priming tool that allows you to adjust primer seating depth, check out the Frankford Arsenal Perfect Seat Hand Primer. This tool comes in a protective case along with a full set of case holders and primer flip tray. A quick thumb release system allows you to switch from small to large primers quickly.
9. Precision Reloading — Bullet Sample Kits, $4.17 and Up
⏺ Good way to test bullets or get a few for your hunt
With these Barnes and Nosler Bullet sample kits, you can try a dozen bullets before you make a big investment. And for hunters, a 12-pack of bullets may be all you need for an annual deer hunt. Use our method to zero your hunting rig in 4 rounds, and you have 8 bullets left for game. Precision Reloading offers a variety of Barnes and Nosler Bullet 12-packs, starting at just $4.17. Calibers on sale include .204, .270, .284 (7mm), and .338.
10. Amazon — Howard Leight MAX Earplugs, $8.40/50 Pairs
20 Pairs
50 Pairs
⏺ Best NRR (33 dB), Very Comfortable, Great Value
These Howard Leight NRR 33 Max Plugs are your Editor’s favorite foam earplugs. Between shooting, motorcycling, and mowing lawns, I probably have Max plugs in my ears 2-3 days a week. This is a very good price for a bulk pack of 50 pairs. NRR 33 is the best Noise Reduction Rating you’ll find for plugs alone. And if you act soon, you can get free shipping to boot.
We support Hunters for the Hungry, a program that feeds needy families in the USA. Hunters for the Hungry (HFH) is a nationwide program that gives back to communities by supplying meals throughout the country. The NRA works closely with state agencies that supervise meat donations. Since the program’s inception, Hunters for the Hungry has brought millions of pounds of game meat to homeless shelters, soup kitchens, and food banks across the United States. This program has been in place for 27 years. In recent years, HFH affiliates donated 2.1 million pounds of meat on average, supplying over 10 million meals.
Hunt and Help Others
Many American hunters are able to harvest more than they can eat or share with friends and family. Through Hunters for the Hungry you can help share your bounty with those in need. All donated game must be field dressed and legally harvested. Note that each state has different rules and regulations for donations, please check with your local drop off location prior to donating.
Big Horn Armory Gives 5% of Sales Proceeds to Wyoming Hunters for the Hungry Program
To help support H4H efforts, Big Horn Armory has partnered with the Wyoming Wildlife Federation (WWF) for a special Pay it Forward H4H program. Throughout November 2020, five percent (5%) of all net proceeds from sales made from the Big Horn Armory website will be donated to the WWF’s H4H program. This donation will help offset the costs of processing donated game meat, which will be distributed to local food banks, pantries, and other food services within Wyoming.
“We are excited to partner with Big Horn Armory, a Wyoming company… to help bring healthy wild game to those in need. We cannot thank them enough for their support of this crucial program” commented Dwayne Meadows, executive director of WWF.
CMP COMPETITION RULES FOR 2020-2021 Are Now Available
CMP Rule Changes are now available as Addenda to 2020 Rules or as complete 2020-21 PDFs (links below). There were not a lot of changes that were approved for 2021. However, most notably, eyewear rules will be more strictly enforced. NOTE: When you open the downloadable PDF files linked below, you will see the new-for-2021 changes displayed in red underlined text. The changes made in 2020 are shown in black underlined text.
Story based on Report by Gary Anderson, DCM Emeritus
CMP Competition Rules for the 2021 competition season have now been approved by the CMP Rules Committee and are posted on the CPM Website. The 2020 competition season was severely impacted by the Covid-19 pandemic and many 2020 events were cancelled, so the CMP still has a substantial inventory of printed 2020 rulebooks. In addition [there were] only a small number of changes for 2021. As a result, the CMP decided not to publish new rulebooks for 2021. 2020 Rulebooks will continue to be used and Errata (Update) sheets are being provided for each rulebook. The rulebooks posted on the CMP website have been updated with 2021 changes are labeled as “2020-2021″ rulebooks. These Rulebooks posted on the CMP website include all 2021 changes. Use the links above to get the latest rules for each discipline.
How to UPDATE Your CMP Rules:
1. If you already have a 2020 rulebook, download the Changes/Updates for that rulebook and note in your 2020 rulebook where those changes apply. (Or use the links above).
2. If you keep your rulebooks on your computer, notebook or cell phone, or want to print your own rulebook, download the Updated 2020-2021 rulebooks from the CMP Website. (Or use the links above).
2020-2021 rulebooks include a diagram showing proper use of eye protection.
When reading the 2020-2021 editions of the rulebooks, note that 2020 rule changes are displayed in black underlined text. 2021 changes are displayed in red underlined text. Those changes do, however, include the addition of a new CMP Service Revolver Match in the Pistol Rules and the addition of F-Class and AR-Tactical Mid- and Long-Range Matches in the Highpower Rifle Rules. The CMP plans to offer competitions in both of these new disciplines in the 2021 National Matches. Another significant change, which has already been announced because it applies this year, is the authorization that competitors may fire a sixth EIC match in years like 2020 when the National Trophy Individual Match is not held.
The 2020 rule requiring Highpower Rifle and Pistol competitors to wear eye and hearing protection while on the firing line has been clarified and strengthened in the 2020-2021 rules.
MANDATORY EYE PROTECTION RULE
One of the most important 2020 rule changes was a requirement that Highpower rifle and pistol competitors must wear eye and hearing protection when they are on firing lines. A big majority of experienced, knowledgeable competitors now agree that protective eyewear is a must for Highpower rifle and pistol shooting, but unfortunately this safety precaution has not been as universally accepted. Incidents involving Highpower rifle and pistol shooting where eye injuries occurred or could have occurred are more common than many realize.
Non-Compliance Results in “No Exceptions” Eye Protection Standards
The CMP Board and staff have carefully evaluated the pros and cons of this safety requirement and have concluded that mandating the wearing of eye and hearing protection is a wise policy. After this rule was introduced, a vast majority of competitors complied with its letter and spirit. Unfortunately, there were a few competitors who did not comply. Some wore shooting glasses to the line and then lowered or removed them while firing. A really strange attempt to evade this rule involved cutting a hole in the part of the shooting glasses lens where the competitor looked while aiming. A few simply refused to comply.
After evaluating experiences with this new safety requirement in 2020, the CMP is taking these additional steps to facilitate compliance in 2021:
— Rule 3.6.2 (both Highpower Rifle and Pistol) has been clarified to clearly require that “two complete lenses” be worn in front of both eyes while firing. Obtaining shooting glasses or prescription eyewear that complies with the ANSI Z87.1 safety standard is “strongly recommended”.
— Pre-match safety briefings in 2021 will include specific instructions about the requirement to wear eye and hearing protection while on the firing line.
— Match officials will give warnings to any competitor who is not in compliance. Refusal to comply with a warning is grounds for disqualification.
— Match sponsors are advised that their match officials need to monitor and enforce this rule and that results from EIC or other matches where this rule was not enforced may not be accepted.
Is your well-built rifle of high-quality components plagued with vertical fliers across more than 1-3 handload combinations? Consider the bedding, crown and scope/sight mounts. Are they correct? If so, then you might check for ignition issues before boldly undertaking an extensive, expensive, and quite possibly fruitless quest for the “magic handload”.
These days, online gun Auctions and Classifieds attract more attention than ever. With so many folks accessing the internet daily, many gun owners find it easier to sell their firearms online rather than in the local gun store. Online selling opens up a much larger audience. With over 53,000 members in the 
For benchrest, F-Class, Silhouette, Tactical or High Power rifles, you may get the best results posting a For Sale ad on a Forum that caters to the right discipline. You want your ad to reach the right audience. On the other hand, a GunBroker.com auction will have tens of thousands of potential buyers. Realistically, however, if you price your rig attractively, it should sell quickly in a Forum Classified Advert. Plus with conventional Classifieds, you can sell immediately — you don’t have to wait for the auction to end. For scopes and reloading equipment (but not firearms, actions, barrels etc.), also consider eBay, which still allows many gun-related items.
In this NSSF Video, Ryan Cleckner, a former Sniper Instructor for the 1st Ranger Battalion, defines the term “MilliRadian” (Milrad) and explains how you can use a mildot-type scope to range the distance to your target. It’s pretty simple, once you understand the angular subtension for the reticle stadia dots/lines. Cleckner also explains how you can use the milrad-based reticle markings in your scope for elevation hold-overs and windage hold-offs.
How to Print Your Targets
When reading the 2020-2021 editions of the rulebooks, note that 2020 rule changes are displayed in black underlined text. 2021 changes are displayed in red underlined text. Those changes do, however, include the addition of a new CMP Service Revolver Match in the Pistol Rules and the addition of F-Class and AR-Tactical Mid- and Long-Range Matches in the Highpower Rifle Rules. The CMP plans to offer competitions in both of these new disciplines in the 2021 National Matches. Another significant change, which has already been announced because it applies this year, is the authorization that competitors may fire a sixth EIC match in years like 2020 when the National Trophy Individual Match is not held.
