|
|
August 11th, 2024
The USA F-Class National Championships are underway right now in Lodi, Wisconsin. The Mid-Range Championships run August 10-13, 2024, while the Long Range F-Class Championships start on the 14th and run through August 17, 2024. With the Mid-Range event underway today, as you read this, top F-Open and F-TR shooters are aiming their rifles at 600-yard targets. VIEW Nationals Match Program HERE.
2024 NRA F-CLASS NATIONAL CHAMPIONSHIPS
NRA F-CLASS MID-RANGE NATIONAL CHAMPIONSHIP AUGUST 10-13, 2024
NRA F-CLASS LONG RANGE NATIONAL CHAMPIONSHIP AUGUST 14-17, 2024
Event hosted by Winnequah Gun Club and sponsored by Brux Barrels, Criterion Barrels, Krieger Barrels, and Silver Mountain Target.
 There will be two divisions at The F-Class National Championships: F-Open and F-TR. In F-Open the rifles can shoot any cartridge type (up to .35 caliber) and have a 22-lb (10kg) weight limit. A front rest is allowed, and most shooters favor a rest with a joystick control.
In F-TR, two cartridge types are allowed: .223 Remington (5.56×45) or .308 Winchester (7.62×51 NATO), with no restrictions on bullet weight. F-TR rifles are fired off a bipod attached to the rifle’s fore-end. The F-TR weight limit is 8.25 kilograms, or about 18 pounds. This includes the weight of the rifle, scope, and bipod. A sandbag can be used under the rear of the stock. Because of the lower weight limit, which includes the bipod, F-TR stocks tend to be much slimmer and lighter than F-Open stocks which have wide fore-arms to work with the front rests.
F-Open Cartridge Options — Modern Magnum Options
For Today’s Sunday Gunday Story we feature an article about F-Open chamberings by respected rifle builder and past F-Open National Champion Emil Kovan. In this article, Emil reviews some of the new magnum cartridge options that are being employed by F-Open competitors. Many shooters are still using the .284 Winchester (or variants), but an increasing number are shooting 7mm and .30-caliber cartridges based on magnum cartridge types. The 7mm is probably still the favored caliber for F-Open because 7mm bullets offer great ballistics with less recoil than heavier .30-caliber projectiles.
Cartridges for F-Class Part II — Rise of the Magnums
By Emil Kovan
Kovan Match Rifles LLC, www.matchrifles.com | READ Part I in this Series »
A few seasons back, I wrote an article on cartridge choices for F-Class shooters. CLICK HERE to READ ARTICLE. Since the first article I wrote, F-Class has continued to grow, and push the limits of precision and accuracy. While the .284 Win and its variants are still the most common F-Open cartridges, more and more top F-Open shooters are using magnum cartridge types to win competitions and set new records. In this article, I will list some of the advantages and disadvantages of the most commonly used magnums, and will cover the strengths and weaknesses of each one of them.
Performance factors we will consider for magnum F-Open cartridges include:
1. Equal or better accuracy than standard chambers
2. Better ballistic performance
3. Enhanced case life
4. Barrel life
Accuracy Potential of Magnum Cartridges for F-0pen Competition
John Meyrs has won four National Mid-Range Championships using the .300 WSM. Tim Vought used the same cartridge to win two Mid-Range Nationals and used a 7-6.5 PRC to win the long range Nationals. Standard .437″ case head (.308 Win head size) cartridges still have more Nationals wins overall, but the magnums are quickly catching up, and my prediction is that magnums will dominate soon.
The accuracy and precision potential of magnums used in F-Class (.300 WSM, 7-270 WSM, 7mm RSAUM or “7 SAUM”, 7-6.5 PRC) is better than non-magnum cartridges because their shapes are closer to the ideal “fat/short” body associated with wider nodes and extreme precision. For example a .300 WSM is proportionally much closer to the 6 PPC, 6 Dasher, and 6 BRA than is the .284 Winchester.
Stunning F-Open rifle with SEB Mini front rest with Blake Machine accessories.
The first thing that comes to mind when magnums are discussed is power and speed. In my humble opinion most shooters are missing out on accuracy because they push their magnums right past the most stable and accurate nodes. Recently I met my good friend from the Army Marksmanship Unit, SFC Brandon Green, at a shooting competition. We discussed the latest and greatest in long-range shooting. I knew that the USAMU had switched from 6.5-284 Norma to 7mm RSAUM several years back, but didn’t know what load they are currently using. Brandon told me that the load featured Berger 180gr hybrids in Nosler cases at 2820 fps. We all know that the 7 SAUM is capable of much higher speeds, “but at around 2820 fps the load/rifle combo will hammer the X-Ring anywhere under any conditions” SFC Green said.
F-Open rifles on the firing line at the Ben Avery Shooting Facility in Phoenix, Arizona.
Most shooters jump right into magnum territory velocities when testing, missing out on better precision at standard chamber speeds. For example, my 30 KMR can easily reach 2880 fps with 230gr Hybrids, and it actually shoots pretty good. But the same rifle at around 2770 fps will absolutely hammer the X-Ring in any condition anywhere. When it’s all said and done, F-Class is a long-range shooting competition at a known distance which requires extreme precision and accuracy. It is not a speed race.
IMPORTANT — Case-Head Dimensions Do Make a Difference
Magnums, when shot within reasonable velocities, on average will give better case life due to the bigger case + lower pressure and “more meat” in the case-head area. For example a 7 SAUM case will outlast a .284 Win case when both are loaded to around 2900 fps.
Disadvantages of Magnum F-Open Cartridges
Perhaps the biggest disadvantage linked to magnums is recoil. Some people complain about developing the “gun shy” syndrome after shooting a magnum for a while. Muzzle blast and recoil are significantly more pronounced in magnums, but that can be easily managed with a properly-built rifle equipped with appropriate recoil mitigation hardware such as RAD and the various butt plates.
F-Open rifle equipped with recoil reduction buttpad system.
Barrel Life — “Barrels are Expendable Components”
It is true that certain magnums can torch a barrel in just a few hundred rounds. But the same is true when improving a 6BR to 6 Dasher for example — barrel life might be reduced significantly. More powder = more heat = diminished accuracy after a certain round count. In my experience, a F-Open magnum’s barrel life is very close to high-performance standard cartridges such as the .284 Shehane or .284 KMR. I “retire” my barrels around 1200 rounds regardless of the cartridge being a magnum or not. After that many rounds most barrels will still shoot OK but will copper up, and you will start seeing those unexplained vertical 9s. The bottom line is this, barrels are expendable components very much like brass. You can’t get the performance of .300 WSM and the barrel life of the .308 Win at the same time. If you want to race in NASCAR, fuel mileage should not be the top priority!
Top Magnum Cartridge Types Used in F-Class Open Division
.300 Winchester Short Magnum
The .300 WSM (Winchester Short Magnum) tops the popularity chart in F-Class Open division. It has been used to win numerous National championships and has set many National records. The .300 WSM’s short/fat case shape, with minimal body taper and 35-degree shoulder, contribute greatly to its outstanding performance at long range. Components are readily available as well. Best brass remains to be Norma, although ADG is just as good and some would even say better, but it is more expensive and harder to get at this time.
The .300 WSM has been described as a “super-sized Dasher”.
For the .30-cal magnums, in my opinion, the best bullets by far are made by Berger. If your rifle does not shoot 215gr, 230gr hybrids, or 210gr VLDs well, you likely have a rifle problem, NOT a bullet issue. My “go to” bullet is the Berger 230gr Hybrid. The 215-grainer is a close second, followed by Berger’s accurate but ballistically inferior 210gr VLD, which I use in calm and steady conditions.
Top powders for the .300 WSM are Hodgdon H4831SC and H4350. I know there are many more powders suitable for the .300 WSM cartridge, but none I have used can match Hodgdon’s consistency when shot in different geographical locations and weather conditions.
7mm Remington Short Action Ultra Magnum
The 7mm RSAUM (aka 7 SAUM) used to be the darling of F-Open. Its case capacity and shape are about perfect for launching 180gr pills with great ballistics and precision. Its popularity faded a little, due to the lack of good brass, and the rise of the improved versions of the .284 Win which can almost match the RSAUM performance. Norma still makes 7 RSAUM brass which is pretty good but little on the soft side and hard to find. ADG is arguably producing the best RSAUM brass right now. It is very uniform, reasonably priced, and seems to hold up very well even when pushed hard. The best bullets are again made by Berger, and those are the 180gr hybrid, 184gr hybrid, and 180gr VLD. Best powders are H4831sc, H4350, and Alliant Reloder 16 and Reloder 23.
7-270 WSM, 7-300 WSM, and 7 WSM
The first two are pretty much identical, the only difference being that the 7-270 WSM is necked up .270 WSM while the 7-300 WSM is a .300 WSM necked down to 7mm. I personally prefer the first one since necking-up is easier than necking-down (with fewer doughnut issues).
The WSM case-based 7mms will give you great velocity flexibility as well as superb precision when tuned well. In the 2013 world championship in Raton NM, I was scoring for a gentleman from Canada who was shooting 7-270 WSM. The wind was blowing pretty hard that day. On one of his shots, just before he pulled the trigger the wind gusted. I remember thinking that’s going to be an 8 for sure. The target came up a line 10! I asked him after the match what he was shooting, and he replied 180s at 3100fps. Although capable of such speeds, I think that potentially better and more consistent accuracy can be achieved at much slower speeds. The best powders and bullets are again Hodgdon and Berger respectively. Best cases are made by Norma and ADG, with Winchester being a third option.
7-6.5 PRC — Popular Wildcat
Last but not least on our chart is the 7-6.5 PRC. This particular cartridge is actually a wildcat. It is a 6.5 PRC necked up to 7mm. It is pretty much identical to the 7 RSAUM with the only differences being a shorter neck and .01″-narrower body. Currently the 7-6.5 PRC is the most requested cartridge that I offer when building new rifles. It seems to fill the gap between the .284 Win and the larger magnums very nicely. It is capable of reaching 3000fps but most shooters are getting their best results around 2920-2950 fps. The biggest advantage of this wildcat is brass. Lapua makes super high-quality, readily-available 6.5 PRC brass. Best powders are H4831sc, H4350, Reloder 16, and Vihtavuori VV 555. The best bullet in my opinion is the 180gr Berger. I am yet to hear about a better-performing bullet in this chamber.
Conclusion
 In conclusion, magnums are not perfect but their performance advantages should be very seriously considered when building a rifle for long-range F-Class. In part three, I will list the most common wildcat magnums, and present the KMR magnums which will make you (if you haven’t already) buy a magnum action and get a magnum build for sure!
Emil Kovan
Kovan Match Rifles LLC
www.matchrifles.com
Emil Kovan Competition History:
– 2014 F-Class Open National Champion
– 2015 F-Class Open National Championship, Silver Medal
– F-Class Open National Championship Teams, 2015, 2014, 2013, Shooting Team Member
– Over 15 wins in Regional and State Championships in Palma, F-TR, F-Open
– 2013 U.S. National Team Member
– 2023 F-Open Gold Medal Team USA Member, 2023 World Championship in South Africa
Share the post "Sunday GunDay: F-Class Nationals — New Magnums for F-Open"
July 30th, 2023
Cartridges for F-Class Part II — Rise of the Magnums
By Emil Kovan
Kovan Match Rifles LLC, www.matchrifles.com | READ Part I in this Series »
A few seasons back, I wrote an article on cartridge choices for F-Class shooters. CLICK HERE to READ ARTICLE. Since the first article I wrote, F-Class has continued to grow, and push the limits of precision and accuracy. While the .284 Win and its variants are still the most common F-Open cartridges, more and more top F-Open shooters are using magnum cartridge types to win competitions and set new records. In this article, I will list some of the advantages and disadvantages of the most commonly used magnums, and will cover the strengths and weaknesses of each one of them.
Performance factors we will consider for magnum F-Open cartridges include:
1. Equal or better accuracy than standard chambers
2. Better ballistic performance
3. Enhanced case life
4. Barrel life
Accuracy Potential of Magnum Cartridges for F-0pen Competition
John Meyrs has won four National Mid-Range Championships using the .300 WSM. Tim Vought used the same cartridge to win two Mid-Range Nationals and used a 7-6.5 PRC to win the long range Nationals. Standard .437″ case head (.308 Win head size) cartridges still have more Nationals wins overall, but the magnums are quickly catching up, and my prediction is that magnums will dominate soon.
The accuracy and precision potential of magnums used in F-Class (.300 WSM, 7-270 WSM, 7mm RSAUM or “7 SAUM”, 7-6.5 PRC) is better than non-magnum cartridges because their shapes are closer to the ideal “fat/short” body associated with wider nodes and extreme precision. For example a .300 WSM is proportionally much closer to the 6 PPC, 6 Dasher, and 6 BRA than is the .284 Winchester.
Stunning F-Open rifle with SEB Mini front rest with Blake Machine accessories.
The first thing that comes to mind when magnums are discussed is power and speed. In my humble opinion most shooters are missing out on accuracy because they push their magnums right past the most stable and accurate nodes. Recently I met my good friend from the Army Marksmanship Unit, SFC Brandon Green, at a shooting competition. We discussed the latest and greatest in long-range shooting. I knew that the USAMU had switched from 6.5-284 Norma to 7mm RSAUM several years back, but didn’t know what load they are currently using. Brandon told me that the load featured Berger 180gr hybrids in Nosler cases at 2820 fps. We all know that the 7 SAUM is capable of much higher speeds, “but at around 2820 fps the load/rifle combo will hammer the X-Ring anywhere under any conditions” SFC Green said.
F-Open rifles on the firing line at the Ben Avery Shooting Facility in Phoenix, Arizona.
Most shooters jump right into magnum territory velocities when testing, missing out on better precision at standard chamber speeds. For example, my 30 KMR can easily reach 2880 fps with 230gr Hybrids, and it actually shoots pretty good. But the same rifle at around 2770 fps will absolutely hammer the X-Ring in any condition anywhere. When it’s all said and done, F-Class is a long-range shooting competition at a known distance which requires extreme precision and accuracy. It is not a speed race.
IMPORTANT — Case-Head Dimensions Do Make a Difference
Magnums, when shot within reasonable velocities, on average will give better case life due to the bigger case + lower pressure and “more meat” in the case-head area. For example a 7 SAUM case will outlast a .284 Win case when both are loaded to around 2900 fps.
Disadvantages of Magnum F-Open Cartridges
Perhaps the biggest disadvantage linked to magnums is recoil. Some people complain about developing the “gun shy” syndrome after shooting a magnum for a while. Muzzle blast and recoil are significantly more pronounced in magnums, but that can be easily managed with a properly-built rifle equipped with appropriate recoil mitigation hardware such as RAD and the various butt plates.
F-Open rifle equipped with recoil reduction buttpad system.
Barrel Life — “Barrels are Expendable Components”
It is true that certain magnums can torch a barrel in just a few hundred rounds. But the same is true when improving a 6BR to 6 Dasher for example — barrel life might be reduced significantly. More powder = more heat = diminished accuracy after a certain round count. In my experience, a F-Open magnum’s barrel life is very close to high-performance standard cartridges such as the .284 Shehane or .284 KMR. I “retire” my barrels around 1200 rounds regardless of the cartridge being a magnum or not. After that many rounds most barrels will still shoot OK but will copper up, and you will start seeing those unexplained vertical 9s. The bottom line is this, barrels are expendable components very much like brass. You can’t get the performance of .300 WSM and the barrel life of the .308 Win at the same time. If you want to race in NASCAR, fuel mileage should not be the top priority!
Top Magnum Cartridge Types Used in F-Class Open Division
.300 Winchester Short Magnum
The .300 WSM (Winchester Short Magnum) tops the popularity chart in F-Class Open division. It has been used to win numerous National championships and has set many National records. The .300 WSM’s short/fat case shape, with minimal body taper and 35-degree shoulder, contribute greatly to its outstanding performance at long range. Components are readily available as well. Best brass remains to be Norma, although ADG is just as good and some would even say better, but it is more expensive and harder to get at this time.
The .300 WSM has been described as a “super-sized Dasher”.
For the .30-cal magnums, in my opinion, the best bullets by far are made by Berger. If your rifle does not shoot 215gr, 230gr hybrids, or 210gr VLDs well, you likely have a rifle problem, NOT a bullet issue. My “go to” bullet is the Berger 230gr Hybrid. The 215-grainer is a close second, followed by Berger’s accurate but ballistically inferior 210gr VLD, which I use in calm and steady conditions.
Top powders for the .300 WSM are Hodgdon H4831SC and H4350. I know there are many more powders suitable for the .300 WSM cartridge, but none I have used can match Hodgdon’s consistency when shot in different geographical locations and weather conditions.
7mm Remington Short Action Ultra Magnum
The 7mm RSAUM (aka 7 SAUM) used to be the darling of F-Open. Its case capacity and shape are about perfect for launching 180gr pills with great ballistics and precision. Its popularity faded a little, due to the lack of good brass, and the rise of the improved versions of the .284 Win which can almost match the RSAUM performance. Norma still makes 7 RSAUM brass which is pretty good but little on the soft side and hard to find. ADG is arguably producing the best RSAUM brass right now. It is very uniform, reasonably priced, and seems to hold up very well even when pushed hard. The best bullets are again made by Berger, and those are the 180gr hybrid, 184gr hybrid, and 180gr VLD. Best powders are H4831sc, H4350, and Alliant Reloder 16 and Reloder 23.
7-270 WSM, 7-300 WSM, and 7 WSM
The first two are pretty much identical, the only difference being that the 7-270 WSM is necked up .270 WSM while the 7-300 WSM is a .300 WSM necked down to 7mm. I personally prefer the first one since necking-up is easier than necking-down (with fewer doughnut issues).
The WSM case-based 7mms will give you great velocity flexibility as well as superb precision when tuned well. In the 2013 world championship in Raton NM, I was scoring for a gentleman from Canada who was shooting 7-270 WSM. The wind was blowing pretty hard that day. On one of his shots, just before he pulled the trigger the wind gusted. I remember thinking that’s going to be an 8 for sure. The target came up a line 10! I asked him after the match what he was shooting, and he replied 180s at 3100fps. Although capable of such speeds, I think that potentially better and more consistent accuracy can be achieved at much slower speeds. The best powders and bullets are again Hodgdon and Berger respectively. Best cases are made by Norma and ADG, with Winchester being a third option.
7-6.5 PRC — Popular Wildcat
Last but not least on our chart is the 7-6.5 PRC. This particular cartridge is actually a wildcat. It is a 6.5 PRC necked up to 7mm. It is pretty much identical to the 7 RSAUM with the only differences being a shorter neck and .01″-narrower body. Currently the 7-6.5 PRC is the most requested cartridge that I offer when building new rifles. It seems to fill the gap between the .284 Win and the larger magnums very nicely. It is capable of reaching 3000fps but most shooters are getting their best results around 2920-2950 fps. The biggest advantage of this wildcat is brass. Lapua makes super high-quality, readily-available 6.5 PRC brass. Best powders are H4831sc, H4350, Reloder 16, and Vihtavuori VV 555. The best bullet in my opinion is the 180gr Berger. I am yet to hear about a better-performing bullet in this chamber.
Conclusion
In conclusion, magnums are not perfect but their performance advantages should be very seriously considered when building a rifle for long-range F-Class. In part three, I will list the most common wildcat magnums, and present the KMR magnums which will make you (if you haven’t already) buy a magnum action and get a magnum build for sure!
Emil Kovan
Kovan Match Rifles LLC
www.matchrifles.com
Emil Kovan Competition History:
– 2014 F-Class Open National Champion
– 2015 F-Class Open National Championship, Silver Medal
– F-Class Open National Championship Teams, 2015, 2014, 2013, Shooting Team Member
– Over 15 wins in Regional and State Championships in Palma, F-TR, F-Open
– 2013 U.S. National Team Member
– 2023 F-Open Gold Medal Team USA Member, 2023 World Championship in South Africa
Share the post "Sunday GunDay: Cartridges for F-Class — Rise of the Magnums"
July 7th, 2019
Ric Horst’s 7 WSM is a game-slayer with serious long-range accuracy. Here’s a hunting rifle (with tactical trappings) that performs as well as some purpose-built benchrest rifles, delivering half-MOA ten-shot groups at 1000 yards–from bipod no less! That was noteworthy in itself. But Ric’s rifle, built to take game in Wyoming’s backcountry, also proves the viability of the 7mm Win Short Mag as a true precision cartridge. With the capacity to drive hard-hitting, ultra-high-BC bullets, the 7 WSM is a bonafied rival to the big 30s. This rifle sets a very high bar for long-range hunting rigs.
The Challenge: Creating the Ultimate Long-Range Hunting Rifle
Q: Tell us how you got interested in the 7 WSM and how you got started on this project?
Ric Horst: Chris Matthews and I were invited to help out with a new hunting show on a cable network. We wanted to showcase a rifle that wasn’t typical for the TV program which was about Antelope and Mule Deer hunting in Wyoming. We considered a variety of calibers, but then Sierra announced their new 175gr (.284) MatchKing and that got our attention. In Wyoming, the key thing in choosing a caliber is the availability of good high-BC bullets–the wind will own you out here. After seeing Sierra’s projected BC for the 175s this seemed to be a no brainer. So I told Chris to make the rifle a 7mm WSM.
Q: What were your objectives with this project rifle? Sounds like you wanted to build a state of the art long-range hunting rig?
Our goals were simple–we wanted a tack-driver with long-range capabilities, from 400 to 1000 yards. Really, at the time, the choice of the 7 WSM was easy–no one else was really doing it, and if they were, they weren’t talking about it. So we wanted to be the first make it work, one way or another. There were actually no real surprises or problems along the way, other than it was the first time I was shooting a 7mm and the accuracy of the 175gr bullets was better than I expected. I have total faith in Chris’s gunsmithing abilities. This 7 WSM is the sixth rifle he’s built for me–and they’ve all been tack-drivers.
Q: Give us your perspectives on living and shooting in Wyoming. What makes it such a great hunting ground? How do the game mix and terrain dictate your selection of a rifle?
My requirements for my rifles are, I guess, unique. I like tactical-style rifles. This “style” seems to fit my type of hunting here in Wyoming–tough, rugged terrain where you need to be able to make the long shot should one present itself. Living in Wyoming? Well, if you choose to live in the “out of town” places you need to be well-prepared and tough. Going to town means a 50-mile trip. You don’t just run to the convenience store if you need something. Plus the weather is hard in the winter and always windy. We joke that we have just two seasons, three months of summer and nine months of winter. Our spring and fall are each about two weeks long.
Despite the weather, Wyoming is a great place for a hunter. Game here is second to none: deer (whitetail and mulies ), antelope, elk, sheep, moose, plus varmints galore. What is great about my location is that I can shoot just about anytime I want. I have the ability to shoot as far as 3500 yards out my back door if I choose. Here’s a shot of my playground.
Putting It Together: Exceptional Components and Accurate Ammo
Q: Your 7 WSM has logged 10-shot groups at 1000 yards that could win many 1K benchrest matches. What kind of components does it take to deliver this kind of accuracy?
 There is nothing super-exotic in this rifle, but it IS fitted out with some of the best components on the market. We did start with a factory action, however, a Remington 700 short action. Chris trued the action, added an SSG over-sized bolt knob, and fitted the action with a Broughton 5C, 9-twist #7 contour barrel finished at 24″. To reduce recoil we added a Badger brake. The stock is a fiberglass McMillan HTG (General Purpose Hunting) stock in Desert Camo. (This McMillan stock design replicates the original M40A1 Marine Sniper Rifle stock.) Since this is a repeater we added a Wyatts Mag Box. The gun features Badger bottom metal, Badger scope rail and Badger Rings. The Scope is a 4-16 Nikon Tactical, which, so far, has proven to be excellent. All the metal is Teflon-coated in Mil-Spec OD Green. I have a bubble-level mounted on the scope rail.
Q: To achieve the results you’re getting you must have exceptional hand-loads. What is your reloading procedure and do you have any “secret tips” to share?
 I use Winchester-brand brass and Winchester Large Rifle Magnum primers. My current load is 64.0 grains of H4831sc for the Hornady 162s (2950 fps) and 61.0 grains of H4831sc for the Sierra 175s (2830 fps).
The only sizing dies I have used are the Basic Redding FL dies–I have since started using the Forester Ultra-Seater and used it when I shot the outstanding groups. My reloading technique is pretty basic. I full-length size and trim all to length. I use the RCBS powered Trim Mate™ station to do most of the brass prep. I do use the VLD case mouth deburrer. I uniform the primer pocket and chamfer as well. I then fire-form those prepped cases. I’ve noted that the new brass usually shoots just as well as fire-formed cases. I then use the FL die to bump the shoulder back .002″. I haven’t really noticed and major difference between Forester and Redding dies except price. I don’t have any “special” secret loading techniques. If you use quality components, I’ve found that you don’t need to weigh this weigh that etc. I tried that for years and it never really showed results to justify the time and effort. I quit doing all the weighing ( except for bullets ) and I shoot just as well. The two things I am anal about are the powder charge and seating depth–these all have to be exactly the same for each round!
I do take time to uniform the brass. First, when I get a bag of brass, I’ll check to make sure all the flash holes are centered, and I’ll pitch the ones that aren’t. Then I’ll measure the shortest case and trim all to that length (after ensuring that fits my chamber). Next, I’ll uniform the primer pockets, and debur and bevel the flash hole on both sides. Beveling both sides is one trick I think helps keep ES down. By beveling the flash side it basically takes the flash and tapers/funnels it to the hole. I think you get more consitency with the primer flash this way. Finally I’ll debur/champfer the inside and outside of the neck using a VLD chamferer.
After firing the cases once, I clean them all up and make one pass on the neck turner just to “clean” the necks to a consistient diameter. Note, I am not necessarily turning for a specific diameter because I have enough clearance to start with. I do this light turn just for consistency. Sometimes the neck turner might only shave a bit off one side.
Q: What’s your load-testing procedure? Do you have any special methods to evaluate/tune your loads?
Again, my methods are pretty simple. I start with the Sierra Load Manual, select the bullet weight, then find the max load for a recommended accurate powder. I like Hodgdon powders, so I start with an “H” powder with an appropriate burn rate, drop the “max” load about 0.5 grains and start there. Typically there is a sweet spot within half a grain up or down from that starting point. I usually seat my bullets to touch the lands or seat just in a bit. I feel this makes up for any bullet-run out when seating them.
When load-testing, I try to get 100-yard groups to be half an inch or less (quarter-MOA is pretty good for me, but not something I can count on regularly.) I then go to the 300- and 500-yard steel plates to see if the load holds its accuracy. If it does, then the load is good to go. However, I will shoot a 5-shot group every now and again to see if I am still in tune. In fact I was re-testing the 162gr A-Max and 175 gr SMK loads the day I shot the screamers at 1013 yards. Two great groups back to back.
Q: How does your 7 WSM perform in terms of recoil and accuracy? Has it met your expectations?
 This rifle is by far one of the most fun rifles I have ever had. The recoil is very minimal with either of the loads and the rifle just plain flat-out shoots. The break-in took all of 21 rounds I think. This rifle shoots sub-2″ groups at 500 yards all day every day (often closer to 1″). Note that I don’t do any shooting from a bench and rests except for the initial load work up. The rest of the time I shoot from a bipod. I would really like to stress that I shoot exclusively with bi-pod and “sand-sock”. So many guys out there think that you have to shoot from a bench to get outstanding results. This simply isn’t true. If you are a disciplined shooter and have correct shooting techniques you can do amazing things from any shooting position. Long Range doesn’t have to be from a rest or bench!
What makes this rifle special is that it has an identical twin, built by Chris for my hunting partner Steve. Both rifles shoot exactly the same–same accuracy, same velocity, same trajectories. I never shot a 1K group with Steve’s gun, but at other distances, including 500 yards, it has performed identically to mine. I shot a sub-moa group of 12 shots one day with the Twins. I shot six shots from each rifle, alternating rifles between shots. Remember this is from the prone position and off a bipod–same load, two different rifles–and it produced a single, sub-MOA group. Now that’s consistency. Both these rifles I call point and shoot rifles–point them on target and they’ll shoot it.
Q: What technique do you use when shooting from bipod?
I basically do Froggy’s technique when shooting from a bipod. I get my natural point of aim, then push forward a bit to pre-load the bipod legs. In gripping the stock, I use just my two middle fingers to apply firm pressure straight back into my shoulder. I’m careful not to torque with the thumb or pinky finger. With my focus on the intended point of aim, I’ll let the cross hairs blur a bit and gently press the trigger until it goes boom. Then follow through, watch for the impact, and chamber the next round.
| Looking Out to 1000 Yards, and the Results from Ric’s 7 WSM |
 
Share the post "Sunday GunDay — 7mm WSM Hunter with Match-Grade Accuracy"
|
