33XC — Popular ELR Cartridge
Paul Phillips is a past King of 2 Miles (K02M) winner. The founder of the Global Precision Group, Paul is one of the top ELR marksmen on the planet. He has also been a team-mate of past K02M winners.
In 2019, Paul had this rifle built for the 25-lb max, .338 caliber-or-under ELR Class. This is chambered for the 33XC, an efficient cartridge devised by 11-time National HP Champion David Tubb. With promising initial testing at 500 yards, it looks like Paul’s 33XC project is a success. The rifle’s first match was the NRA Extreme Long Range Championship held in 2019 at Camp Atterbury, Indiana.
Paul reports: “The 33XC is ready… I have tested loads from 3100-3450 FPS and and will settle on a load around 3250 FPS [which is] my most accurate load so far. The Peterson Cartridge brass is really working well.”
Paul states he would like to look for a higher node from 3300-3400 GPS: “Next stop is with the Applied Ballistics LLC mobile labratory and radar testing with a PDM.” Paul cautions: “I encourage everyone to start low and work up. Every chamber, barrel, and components are a little different.”
During initial testing, Paul’s 33XC put three shots in 0.27″ at 100. Then, at 500 yards, the rifle produced a 3-shot group around 1/3-MOA with just 1.22 inches of vertical. That’s pretty impressive for early testing. Paul will also be trying some Berger bullets soon. When he determines the most accurate load, Phillips will stretch the rifle’s legs, shooting out to 2500 yards and beyond.
Quote: “The Cutting Edge Bullets are not the highest BC but they are very stable and consistent at ELR (sub-sonic) ranges and that’s the most important factor in finding the best ELR bullet. I actually test all my bullets at sub-sonic speeds to make sure they are consistent and stable. Finding a good load at 500 yards is just the first part. The real test is shooting them at sub-sonic speeds and see how consistently they group. This is what gives you the highest percentage to impact at 2 miles and beyond.”
This rifle features a BAT action mated to a 34″ Bartlein barrel chambered for David Tubb’s new 33XC cartridge. Paul Phillips is currently running Cutting Edge 275gr Lazer solid bullets. Paul notes: “I also have a .338 Lapua Magnum barrel and 300gr Berger bullets for the restricted class in France.” Paul gave special thanks to Alex Wheeler for doing the metal work and Alex Sitman for doing the bedding.
Rifle Component List
Action: BAT Machine CTH dual-port action
Trigger: Bullet Central Bix’N Andy
Barrel: Bartlein 1:8″-twist barrel (34″)
Chambering: 33XC for Peterson brass
Stock: McMillan A6 Super Mag, Bedding Alex Sitman
Scope: Nightforce Optics 7-35x56mm F1 ATACR.
Bipod: Duplin Rifles
Paul Phillips notes: “Alex Sitman has been bedding rifles stocks for most of his life. I believe that [bedding] is a very important … to keep consistent accuracy and repeatable zeros after traveling all over the globe.”
Even with the TacomHQ Charlie Tarac scope prism in place, the rifle makes the 25-pound weight limit with Duplin Rifles bipod. Paul says: “I love it when a plan comes together!! I’m under by 2 ounces!”
About the 33XC (eXtra Capacity) Cartridge
David Tubb invented the 33XC cartridge because he thought the CheyTac cases were too much trouble — requiring a larger action, oversize presses, and ultra-expensive dies. The 33XC was designed to fit .338 Lapua Magnum-size actions and use normal reloading presses.
The 33XC (eXtra Capacity) has 137.5 grains of H2O capacity with over 125 grains of usable powder capacity while leaving the 0.393″ neck unfilled for bullet seating.
The 33XC has a .338 Lapua Magnum lineage. Think of it as a better, 35°-shoulder .338 LM. David explains: “The 33XC uses standard reloading dies along with a 7/8″ x 14 TPI reloading press. There is no fire-forming — all case ‘improving’ has already been done with a production case that has 20 grains more powder capacity, 35-degree shoulder, and longer neck compared to a .338 Lapua Magnum. This puts the various .338 Lapua wildcats and the Rem Ultra Mag Improved into the ‘also ran’ category. They simply can’t compete with the velocities attainable with the 33XC.”
The 33XC is based off of a .580″ bolt head. Tubb states that “A fired case will extract with little effort when using a properly-polished chamber with a maximum powder charge after resizing with the Superior Shooting Systems FL sizing die.” Tubb’s 33XC die reaches the case head which is important for accuracy. Peterson Cartridge produces the 33XC brass for Superior Shooting Systems. This high-quality brass costs $260 for 100 cases (i.e. $2.60 per case), and can be purchased directly from Superior Shooting Systems.
Bonus Video — Global Precision Group Team Makes 4-Mile Hit
With a .416 Barrett rifle, Team GPG makes a 4-mile impact that is captured on video during team practice. James Devoglaer was shooting his GPG spec .416 Barrett with Team Captain Paul Phillips doing the ballistics and wind. Spotters were David Parrish and Derek Rodgers. Forward Observers were John Droelle and Mauro Del Mastro. Approximately 60 shots were taken before impact. There were four 3-shot groups that measured under 2 MOA at 4 miles. The .416 Barrett cartridges were loaded with 550gr Cutting Edge bullets and Vihtavuori powder.
For today’s Sunday Gunday feature, we present a splash of color — the beautiful blue 7mm-270 WSM of Forum member Ian B. (aka “Elwood”) from Great Britain. A very knowledgeable guy, Ian has been one of the UK’s top F-Class shooters. And he’s the proud owner of a very “Flash” F-Class rig.
About the Shooter — Ian’s Background
Ian tells us: “I started shooting F-Class Open [many] years ago when a good friend invited me to Bisley to shoot with the Dorset Riflemen. I found it very enjoyable and a real challenge. The next year I attended the GB F-Class league’s Introduction to F-Class course, and soon afterwards started to compete in the GB F-Class league, while still shooting once a month with the Dorset Riflemen. In this short time frame, I’ve managed to finish 8th in the league last year, 12th in the Europeans, and I was a part of the GB squad that won the team event at the European Championship. I was then selected for the GB F-Open World Championship Team. Unfortunately, due to work commitments, I have had to withdraw.”
Ian’s Beautiful Blue 7mm-270 WSM F-Class Rifle
Report by Ian B. (aka “Elwood”)
Having spent my first year competing with a magazine-fed 7mm WSM tactical/sporting rifle (Surgeon action and AICS mag) and doing reasonably well with it, I then moved on to a .284 Shehane (.284 Winchester Improved). I love the Shehane and still use it but … I wanted something for those windy long-range days and so there was only one logical choice, the 7 WSM. This time I chose a 7mm-270 WSM as I quite enjoy case prep (just kidding). Actually, there’s not much to do really. The quality of Norma brass is well known and the Norma 270 WSM brass is quite easy to obtain in the UK.
The action is a Right Bolt, Left Port (RBLP) Stolle Panda F-Class action, with Jewell trigger. There wasn’t any particular reason behind the RBLP configuration — it was more of a case of that’s what I could get at the time. I had a 1.250″-diameter, straight-profile Bartlein barrel finished at 32 inches and chambered for the Berger 180gr VLD with a .313″ neck diameter. All my metal work and quite a bit of the wood work is done by the excellent Neil McKillop of McKillop Engineering. As with all top gunsmiths, Neil is meticulous to a point of obsessiveness and he’s the name behind quite a few winning rifles including several used by the GB Open and F-TR teams. Neil also inletted the stock from a blank and did the bedding for the action and the front bag runners.
Loading for the 7mm-270 WSM
I have one “tried and tested” load: 7mm Berger 180gr VLDs, seated .020″ into the lands, Vihtavuori N165 powder and CCI BR2 primers. This load is supremely accurate, but at 2990 FPS it’s a bit slow. To get more speed, I’m currently testing H1000 with good results, but it looks like I may have a slow barrel. I have another Bartlein barrel chambered and ready to screw on when the weather gets warmer. If that new barrel shoots well, the current barrel will probably be used as a practice barrel.
Loading Procedure
I do full case prep, neck-turning, uniforming primer pockets after the first firing, chamfering necks inside and out, and removing burrs around flash holes. Even the best brass sometimes suffers from imperfect quality control. I try to use Redding dies if possible, and will use bump dies, neck bushing dies, and competition seating dies.
I use an RCBS ChargeMaster 1500 to throw a charge just slightly under my desired weight and then trickle-up to final weight using the superb Dandy trickler and a Gem Pro 250 scale.
I anneal every other firing using a Bench-Source machine. Before this I used a Ken Light and also did them by spinning them in a drill. Never again will I do that after using the Bench-Source. After I have annealed, I always run a nylon brush wrapped in 0000 wire wool into the neck to remove any debris.
I keep to the same lot numbers of primers, powders, and bullets. Even the Bergers can vary from lot to lot — I have two different lots of 7mm 180gr VLDs that vary .020″ from bullet base to the ogive. I trim and point my bullets. Pointing may be a mental thing — I had a fantastic shoot while using trimmed and pointed bullets so I do it all the time now. ( A fellow GB team shot refers to them as “Pointless Dies” — I have witnessed him shoot a 99-14V at 1000 yards with bullets that weren’t trimmed or pointed). My next move will be to start measuring bearing surface…where does it all end?
Custom Wood Stock Was Modified by Ian and Treated to a Fancy Paint Job
The stock is a custom-made design crafted by Joe and Simon West of Joe West Rifle Stocks. I had several modifications done to one of their existing stock designs. Having done a lot of my shooting with the AICS, I was quite used to a thumbhole stock, so thought I would try one in F-Class. I told Simon what I wanted and he sent me down a prototype made from very inexpensive Tulip wood. We had a few discussions and then made some more mods..
I made two main changes to the stock. First, I removed the lip at the bottom of the pistol grip because I felt I might rest my hand on this and possibly disturb the rifle. Second, I had the protruding pistol grip base removed so that the bottom of the stock was completely flat like the Precision Rifle & Tool F-Class stock. Simon also made the finger grips to fit my hand and flattened them off to allow for a bit more movement. The stock was then sent to Hydro Graphics in the UK to have a custom exterior finish. The paint color is a Marbleized Candy Oriental Blue. As always, Hydro Graphics did a great job.
Optics and Rings
The scope is the excellent 5-50x56mm March with the MTR-2 reticle — far and away the best reticle I have used for F-Class. March makes great optics. During the 2012 European individual F-Class event, using another March (my 8-80x56mm), I could see my shooting partner’s impacts in the white V-Bull at 800 yards! And just recently at a club match I called two V-Bulls at 900 yards using the 8-80X (not at full power). Granted the light has to be perfect to be able to do this, but my highest praise for the Deon Optics glass is that it rivals that of Schmidt & Bender. Having owned both March and S&B scopes and compared them side-by-side, I feel that I can make this statement fairly.
UK-based Third Eye Tactical made the nice, 34mm rings. The UK is now producing some excellent products. We now have UK-made custom actions, rings, rails, stocks and more. It would be nice to think we could have a 100% British-made rifle, and not rely completely on USA-made products. I think all we need is the trigger? But I can’t see there ever being a UK-made scope!
Share the post "Sunday Gunday: Blue Beauty from Britain, 7mm-270 WSM F-Open"
Today we feature a top-flight tactical .22 LR rig belonging to Jonathan Ocab. A talented Highpower marksman with the Distinguished Rifleman Badge, Jonathan also enjoys rimfire tactical disciplines which he features on his Youtube Channel. Jonathan has run a monthly NRL22 match in California. His interest in the NRL22 game started with a CZ 455, but soon he stepped up to the impressive rig you see here. This boasts all top-tier components: Vudoo V-22 mag-fed action, Bartlein barrel, MPA Chassis, and Kahles K525i scope. Jonathan carefully selected all this hardware and assembled the rifle himself.
My Vudoo/MPA Rifle for NRL22 and Long Range Rimfire Report by Jonathan Ocab,Ocabj.net.
I became interested in rimfire shooting due to not having as much access to longer distance ranges, and the emergence of NRL22 matches. Back in 2017 I had acquired a CZ 455 and ran it in NRL22 club matches. It worked well, but as I started spending most of my time on my club’s rimfire range, I focused on getting a Vudoo Gun Works V-22. The Vudoo V-22 appeared to offer a true repeater that had the feel of a full-sized centerfire rifle along with high accuracy/precision potential.
After a lot of research, I decided to put in an order for a barreled action and acquired a Vudoo Gun Works V-22 action with a 20″ Bartlein barrel, 1-16″ twist, and MTU contour, all in Flat Dark Earth Cerakote (along with a +30 MOA base). I then acquired the TriggerTech Diamond Trigger Pro Curved, Masterpiece Arms BA Comp chassis (in Flat Dark Earth), American Rifle Company M10 34mm rings (28mm height), and Kahles K525i 5-25x56mm SKMR3 LSW scope.
CZ as a Starter NRL22 Option — The CZ 450-series is a solid family of .22 LR rifles, but I wanted to see what existed beyond the CZ level of rimfire rifles. One of my complaints with the CZ 455 is that the trigger leaves much to be desired even with the trigger kits available. Since the Vudoo V-22 action has a Remington 700 footprint and can accept most Rem 700-compatible triggers, I can actually run a top-tier trigger that would exceed anything available for the CZ.
Component Selection for the Ultimate NRL22 Competition Rifle
My choices in components were biased due to my prior experience — I went with quality hardware I knew and trusted…
Barrel Choice — I chose the Bartlein barrel over Vudoo’s in-house Ace barrels because I run a Bartlein barrel on my 6mm Creedmoor rifle and I have become a big Bartlein fan. Secondly, I chose the Masterpiece Arms BA Competition chassis because I also run the MPA BA Comp on my 6mm Creedmoor rifle. You can see the two rifles side-by-side below:
You are not seeing double. There are two rifles, both with an MPA Comp BA chassis, and both weighing about 15 pounds. In front is the featured Vudoo-action .22 LR rimfire rig with 20″ barrel, while behind is Ocab’s ARC Mausingfield 6mm Creedmoor PRS/NRL centerfire rig with 24″ barrel.
After running this rifle build for over a year now, I can say that I am more than happy with this platform as I have it configured. Having a .22 LR rifle in the same chassis as my 6mm Creedmoor rifle makes me feel right at home behind either rimfire or centerfire platform. My Vudoo V-22 weighs 15.2 lbs with Atlas CAL bipod while my 6mm Creedmoor rifle build weighs right at 15.0 lbs with the same Atlas CAL bipod. The “feel” and handling of my Vudoo V-22 MPA is as close to a centerfire gun as you can get.
Scope and Rings — I chose the 5-25x56mm Kahles K525i SKMR3 LSW because I was interested in running the Kahles after handling a few K624i and K525i scopes and hearing about how great they tracked. I run ARC M10 rings on several rifles because I think they are superbly designed.
Trigger Choice — I chose the TriggerTech Diamond because I already have a TriggerTech on one of my centerfire platforms and I wanted to try their Diamond trigger on a gun.
Outstanding Accuracy with Multiple .22 LR Ammo Types — Lapua and SK
My .22 LR ammo of choice is Lapua Center-X. This is the most commonly-chosen ammunition among Vudoo V-22 shooters. I also had good results with SK Rifle Match and Lapua Midas+ in casual 50-yard and 100-yard testing but have stayed with Lapua Center-X because my rifle shot all the lots of Center-X I put into it equally well out to 200 yards.
SUMMARY — The Vudoo V-22 and MPA Package Is Outstanding
I can hands down recommend the Vudoo Gun Works V-22 for anyone who is interested in getting one. The “full-sized” rimfire rifle segment is not a one-horse race anymore and there are other options out there, but I feel very few will regret going with a Vudoo V-22 over another alternative. If you do not have a centerfire rifle designed for NRL/PRS style of shooting, you could probably just opt to go with a CZ 457 or Tikka T1x and have a lot of room to modify and tailor those rifles to your own tastes and still have an accurate rifle for NRL22. But if you also run a precision centerfire rifle, you should seriously consider a Vudoo V-22 or other 700-pattern rimfire action if purchasing a new .22 LR rimfire rig.
My Vudoo Gun Works V-22 build is an all-purpose gun for me. It is setup for NRL22-style matches but can be utilized for (extreme) long range .22 LR shooting (300 yards and beyond). For that rimfire ELR Game, I am seriously considering getting a Vudoo V-22S (single-shot) action to put in an F-Class stock to have a dedicated ELR .22 LR gun. While I built my Vudoo Gun Works V-22 with NRL22 in mind, I realized this gun could do more so I took it out to shoot 300 yards. After that, I stretched it out to 400 yards and then 500 yards in subsequent range visits. Now I am intrigued by extreme long range .22 LR shooting and often shoot 400 yards and beyond with the Vudoo V-22 when I can.
Long Range .22 LR Rimfire — Out to 500 Yards
Jonathan shoots his competition rifle in Long Range Rimfire matches with targets out to 500 yards. That’s definitely Extreme Long Range for the little .22 LR cartridge, requiring 27.8 MILs of up elevation! Jonathan notes: “I originally had a +30 MOA base on my rifle and it worked fine to 400 yards, but I ran out of adjustment on the K525i to get to 500 and had to hold over. I ended up getting a +40 MOA base.”
NRL22 Competition — Tactical Rimfire Matches
The NRL22 match format is a great shooting discipline. NRL22 offers a high fun factor at relatively low cost. You don’t have to reload match ammo. A couple of 50-round boxes of .22 LR ammo will get you through the match. While some people bring lots of gear to matches, that’s by choice and not by necessity. You can keep it simple and still be competitive (and win).
Tips for NRL22 Competitors
I am a match director at my gun club and run our local NRL22 matches. People often ask me for tips for competing in NRL22. First, I recommend getting the course of fire for the month in advance and practicing those stages at the range. Here are other specific tips that should help NRL22 competitors improve their gun-handling and match results.
1. Dry Fire Practice — If you are not able to do live fire practice at the range, I encourage shooters to practice their shooting positions at home via dry fire. Setup props or barricades with pasters or other faux targets on a wall in the garage or inside the house and run through each stage.
2. Scope Magnification Level — The most common issue I see with newer shooters in NRL22 is the tendency to maximize their scope magnification. The timer will start, and the shooter gets into position on a target, but the scope is set to 15x or higher and the shooter can’t find the target. The shooter lowers the magnification, locates the target, and then increases the magnification again, takes the shot, transitions to another target, and repeats the process of decreasing magnification, locating target, etc. Novice NRL22 shooters should try using the mid-range magnification. Try shooting 7x-12x and learn to balance field of view and target image.
The author at NRL22 Match at West End Gun Club in San Bernardino, CA.
3. Support Side Shooting — NRL22 matches often include support-side shooting stages. This requires you to shoot with your opposite (non-dominant) hand and eye. I often hear people complain about shooting support-side. My only real tip for this is to actually spend time at the range shooting this way. Practice makes perfect. It’s all a question of learning how to shoot again and using fundamentals. Learn to get a consistent cheek weld and consistent eye relief. If necessary, figure out if you need to set your scope’s diopter for your opposite eye and mark it on the scope.
4. Tripod Practice — Even though tripods are not used in the NRL22 courses of fire, I practice shooting off of a tripod often. I will often setup targets at various distances and spaced far apart to run drills firing shots on each target with the goal of speeding up transitions and target acquisitions. Target acquisition after transition from target to target is where time is lost, so it is good to become efficient in this area.
BONUS Video — Modern NRL22 Hardware, Optics, and Ammo
Released on October 5, 2024, this recent Pursuit of Accuracy channel video reviews some of the latest and greatest equipment options for NRL22 and Precision rimfire disciplines. The host covers action and stock options at 1:10 time mark. Then at the 4:00 minute mark, he explains popular scope options. At 7:02 in the video he explains how he selects and tests .22 LR ammunition (he favors ELEY). Finally, at 11:52 he explores barrel options while including suggestions on efficient barrel maintenance. This video includes excellent Shooter’s POV footage shot with a video camera mounted on the rifle.
Share the post "Sunday Gunday: .22 LR Rimfire Precision Tactical Rifle for NRL22"
Brian, a gunsmith at GA Precision, built this rimfire rig with GAP colleague Anthony Soukup.
On his Facebook page, Tactical competitor Bryan Sikes posted a photo of a rimfire rig we really liked. Brian works at GA Precision. He and fellow GAP gunsmith Anthony Soukup built this rifle. With a modified Rem 40X action, Manners stock, Bartlein barrel, and Mack Brothers suppressor, this rig has top-quality components stem to stern. And Bryan tells us this rifle performs as good as it looks: “This is the baddest little .22 LR trainer ever. I’m stoked about it. With the barrel length and can, it’s the exact length of my regular comp rigs.” With length, balance, and ergonomics near identical to Bryan’s centerfire competition rifles, this 40X is a superb training tool.
Many readers wanted to know about the bottom metal and the detachable box magazine. Bryan Sike reveals: “The magazine setup is designed specifically to replicate my actual competition rifles. The bottom metal is for use with AI magazines and uses a standard M5 type inlet just like any centerfire completion rifle. In this case with the .22LR, Mike Bush designed a high reliability rimfire magazine using the same outside dimensions as an AI magazine. This rifle was built no different from any other. The action was modified and trued, barreled, fully bedded, etc. using ALL components common to centerfire match rifles.” The Rem 40X action was modified by Modacam Custom Rifles to work as a repeater with box mags.
Bryan adds that a new rimfire action is in the works: “My preference is modified Remington 40X actions and the [Vudoo Gunworks V-22 Action]. Both of which are TRUE repeaters and don’t feed from a Savage magazine. This rifle feels nothing like a .22 LR and that was the whole point.”
Why You Need a .22 LR Tactical Cross-Trainer
Many guys who shoot long-range tactical matches practice with .22 LR rifles of similar configuration. Rimfire ammo is way more affordable than centerfire, you do not need a big range facility, and shooting rimfire saves wear and tear on your centerfire rifle. Further, for learning how to read the wind, there really is no better training tool than a .22 LR, even as close as 50 yards.
Our Friend “DesertFrog”, who shoots tactical matches in Southern California, explains: “I used to shoot an average of 200 rounds of .308 Match ammo a month for training (50 per weekend). These days I shoot maybe an average of 50 rounds of .308 Win per month and probably around 600 rounds of .22 LR. Using mainly the .22 LR for practice did NOT hurt my standings in actual competitions. I shot my .308 just as well in matches, but saved the cost of hundreds of rounds of .308. If I didn’t reload and was still buying boxes of Federal Gold Medal Match .308 Win [at $1.75/round], this would be a savings of [$262.50 per month on the centerfire ammo (150 rounds).]” Money saved is money earned.
Targets for Rimfire Cross-Training
SPECIAL BONUS–Rimfire Tactical Precision Targets
These FREE targets by DesertFrog are offered in Adobe Acrobat format for easy printing. CLICK HERE to download all six targets as a .ZIP archive.
Share the post "Rimfire Excellence — Bartlein-Barreled .22 LR Tactical Tackdriver"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Bullet Central — Krieger and Bartlein Pre-Fit Barrels
⏺ Great quality pre-fit barrels, ready to mount to your rifle
Do you own a Kelbly, BAT, or Impact action and need a new barrel but don’t want the hassle (and cost) of having a smith chamber and headspace the barrel? Consider a Krieger or Bartlein Pre-Fit Barrel from Bullet Central. On BulletCentral.com you’ll find a wide range of barrels in various calibers for multiple action types. Place your order for professionally-chambered, custom-grade barrels that you can install yourself.
2. KYGUNCO — S&W M&P 15-22 Bundle, $414.99 with Rebate
⏺ Get 15-22 Rifle with $75 Rebate, plus S&W Carry Case, eye/ear protection
Smith & Wesson’s M&P 15-22 is a great rimfire AR clone — a good choice for NRL22 and/or rimfire 3-Gun games. Currently KYGUNCO is offering a great special bundle with 15-22 rifle, S&W logo carry case, Walker Sport Glasses, and Surefire EPE Ear protection. The rifle is complete with Magpul folding sights plus M-LOK handguard. Note the $489.99 S&W 15-22 Bundle price (before rebate) is listed on KYGUNCO’s Tax Time Sale Flyer. However the web site is still showing a $496.07 pre-rebate price. Either way this rifle bundle qualifies for FREE Shipping.
3. Midsouth — SK Rimfire Ammo Sale
⏺ Very good ammo that works great for NRL22 and local fun matches
SK makes excellent .22 LR ammo. We have friends competing in NRL22 and SK is their top choice — as it offers great accuracy at an affordable price. Right now SK Ammo is on Sale at Midsouth. Get a 50rd box of SK Semi-Auto for $7.99 or choose SK High Velocity, just $86.99 for 500 rounds. We’ve found SK ammo performs better than some other brands at $10-$11 per box.
⏺ Great deals on durable AR500 steel targets — watch video below right
Caldwell’s new bright, easy-to-see steel targets come in multiple shapes and sizes for competition, training, and recreational use. Made of AR-500 grade hardened steel, these bright yellow targets can withstand thousands of rounds. Rated up to a 3000 fps impact velocity and a 3500 ft-lb impact energy, these targets come in seven styles and sizes with three hanging solutions. These bright yellow Caldwell AR500 Steel Targets are on sale now on Amazon, starting at just $19.99 for the 5″ Gong Target.
5. Amazon — Midland-EX37VP Radio Kit (Set of 2), $49.99
⏺ Quality Walkie-Talkies with good range and special Emergency functions
Having a good 2-way communication system is vital when hunting or wilderness hiking. And a pair of walkie-talkies really helps during shooting practices when a buddy goes downrange to set targets. A very good 2-Way radio system is the Midland-EX37VP E+Ready Emergency Two-Way Radio Kit. These walkie-talkies have a 26 mile range and feature 22 FRS (Family Radio Service) channels, along with channel scan. With this kit you get vital E+Ready Emergency functionality, plus NOAA weather alerts — important in the event of a natural disaster.
6. Dick’s Sporting Goods — Fortress Safes on Sale
⏺ Great prices on Fortress safes — the big safe is a real bargain
Here are two great gun safe deals. The jumbo-sized Fortress 64+4 Gun Safe will hold up to 64 guns in the main interior, plus four more on the door. It is currently $200 off, discounted to $999.98. With scoped guns, or those with wide forearms or pistol grips, knock that max number down to about 35 guns. That’s still an impressive capacity. This big Fortress-brand safe weighs 545 lbs., measures 56.5″ H x 41″ W x 25″ D, and is fire-rated at 1400°F for 30 minutes. If you are looking for a smaller, secondary safe, the Fortress 12-gun Fire Safe is currently $499.98 on sale ($100 off). This weighs 247 lbs. and is 55.1″ H x 19″ W x 15.3″ D. It is fire-rated at 1200°F for 30 minutes.
If you need a home defense shotgun, but have a tight budget, check out this TR Imports Silver Eagle Inertia One 12ga semi-auto with 18.5″ barrel. This has all the key features you need — fitted sights (adjustable rear, Fiber Optic front), Picatinny rail on top of the action, and pistol grip. This shotgun even comes with a convenient case with four choke tubes. Capacity is 4+1, Weight is 7.8 lbs, and OAL is 38.5″.
8. Grafs.com — Frankford Platinum Case Prep Center, $99.99
⏺ Versatile, easy-to-use unit with 4 powered heads
Grafs.com now has the Frankford Platinum Case Prep Center for $99.99 on SALE (19% Off). This aluminum-body unit features 4 powered tool stations and comes with: (1) inside chamfer tool; (1) outside deburring tool; (1) small primer pocket scraper; and (1) large primer pocket scraper. The machine’s 8-32 threaded output shafts accept a wide variety of aftermarket case prep tools. The 200 RPM shafts are efficient. NOTE: If you want a tool that can TRIM cases, as well as prep cases, check out the Frankford Case Trim & Prep Center for $60 more — $159.95 at MidwayUSA.
9. KYGUNCO — Rossi .22 LR Rio Bravo Lever Rifle, $289.17
⏺ Nice gold-finish lever-action rifle at great price
Classic .22 LR lever guns are fun and inexpensive to shoot. These rifles are great for reactive and steel targets. A lever gun is also an excellent training rig for new shooters. Right now the Rossi Rio Bravo .22 LR rifle is on sale for $289.17 at KYGUNCO. This rifle features a gold-tone steel receiver with dark wood stock + forearm. Capacity is 15+1 rounds of .22 LR. OAL is 36″ and weight is a modest 5.5 pounds.
10. Amazon — Motion-Sensor LED Interior Light, 2 for $24.99
⏺ Activates when door opens, Rechargeable, 3 LED Light Levels
Here’s a great accessory for your Gun Safe. This rechargeable LED Lamp turns itself on when you open the door, and off when you close the door. Select three brightness levels: 10LED, 20LED, 30LED. With the supplied 3M adhesive magnetic strip you can easily attach the light to the inner walls of your gun safe. And then quickly remove the unit for charging with a standard USB cord (no batteries to replace!). It works, it’s handy, and it’s affordable — get a twin-pack with TWO LED motion-sensor lamps $24.99 on Amazon. These LED lamps can also be used in garages, closets, or stairwells.
Share the post "BargainFinder 389: AccurateShooter’s Deals of the Week"
Proud owner Dirk L. says: “This is my first build — never thought it would be a .308!”
Here’s a handsome F-TR rifle with a beautiful red stock that suits the holiday season. This ruby red beauty was a recent addition to the long-running Pride and Joy Rifle thread in our Shooters’ Forum. The rifle belongs to Forum member Dirk L. (aka “Pinkes”) who hails from South Africa. This is a .308 Win, with 30″ Bartlein barrel, and X-Max action. The stock is a custom composite with carbon fiber for strength and lightness. And yes this rifle shoots as good as it looks. Check out the impressive 5-shot groups below…
X-Max for Xmas — Impressive Metal-work
Along with that beautiful red stock, this F-TR rig has some very cool features, including a South African-crafted X-Max Action. The action designer Piet Welgemoed explains: “The X-Max action body is 17-4PH stainless steel pre-hardened to 44° Rockwell. Bolt and handle are one-piece stainless steel, nitrated to 55° Rockwell 0.2mm deep. Bolt is also fluted. Inside is the firing pin with washers (see below). The washer cuts the lock-time almost by half and also weighs less. The bolt-knob and bolt shroud are CNC aluminum. The action has very tight tolerances.” The complete action with +20 MOA rail and trigger weighs 1.475 kg (3.25 lbs).” Owner Dirk notes that the competition trigger, set at 3.0 ounces, is also Welgemoed’s design.
Wicked Accuracy with Bartlein Barrel, Varget, and 220gr SMKs
This gun has already proven to be a great shooter. Below are two FIVE-shot groups at 100 meters. The group on the left is in the low threes, with three of five shots essentially in one hole. Dirk loads Lapua .308 Palma brass and #2231 200gr Sierra Matchkings, seated 20 thousandths off the lands. The Varget powder and CCI primers drives the 200gr SMKs at 2620 fps.
Brass: Lapua .308 Win Palma (small primer) | Primers: CCI 450 | Powder: Varget
Bullet: New 200gr SMK #2231 | Seating: 0.020″ Off | Velocity: 2620fps
Composite Stock — One of Three by Renier Mostert
And what about that beautiful red stock? The rifle’s owner told us: “This was one of three similar stocks built as a test run by Renier Mostert, a professional composite stock builder and former benchrest shooter from Pretoria, South Africa. Renier was approached by three friends, who were all looking for decent, custom-built FTR composite stocks. There were a number of stocks available to them (mostly imported), but [those] were either made of wood or aluminum. The requirements for the composite stock build was very specific. Aluminum V-Blocks for the actions were required. The stocks had to be light enough to carry some beefy barrels and optics without compromising rigidity and still be within the F-TR weight limit. The three friends supplied Renier with an imported wooden stock as their shape of choice. Although the shape was quite straight-forward, Renier made a few dimensional changes to features which were not symmetrically correct on the sample, and then built a mold from it.”
Renier uses several methods to craft composite stocks for various disciplines: F-Class, benchrest, competition rimfire, hunting, and tactical. For this build he chose to build a shell constructed of a well-planned mix of woven fiberglass cloth and bi-directionally woven carbon fiber with aerospace quality epoxy resin to reduce weight in some areas and increase stiffness in other areas. He used a wet lay-up process where the two halves gets laid up and joined together while still wet to form a complete, continuous shell. The closed mold gets cured under pressure in an oven for several hours at very specific temperatures. After curing, the shell is filled with a high-tech mix of lightweight filler and epoxy resin. The composition of the mix varies in different areas of the stock to facilitate more strength or reduced weight where applicable.
After the initial build, the aluminum hardware was installed. An adjustable cheek piece, Anschutz rail, and adjustable recoil pad mechanism were installed. The stocks were inletted by Renier, while the final fitting and bedding procedures were left for each customer’s gunsmith to complete. The stocks were light enough for the rifles to comfortably be within the F-TR weight limit. A barrel tuner was mounted on one of the rifles, and the rifle still made the F-TR Class weight limit, 8.25 kg (including bipod). The bipod shown in photos in the SEB Joy-Pod.
Paint — Candy Apple Red over Metallic Silver Base
After final gunsmithing, the stocks were returned to Renier Mostert for custom painting. The rifle featured in this article was done in Candy-Apple Red paint from DNA Paints (an Australian company). To get the desired effect, a metallic silver base coat was used, enhanced with a modest amount of medium coarse glitter, followed with multiple layers of candy until the correct shade was achieved. A high-quality automotive clear coat was used to finish off the paintwork.
Share the post "Sunday GunDay: X-Max for Xmas — Red Rifle from South Africa"
Brian, a gunsmith at GA Precision, built this rimfire rig with GAP colleague Anthony Soukup.
On his Facebook page, Tactical competitor Bryan Sikes posted a photo of a rimfire rig we really liked. Brian works at GA Precision. He and fellow GAP gunsmith Anthony Soukup built this rifle. With a modified Rem 40X action, Manners stock, Bartlein barrel, and Mack Brothers suppressor, this rig has top-quality components stem to stern. And Bryan tells us this rifle performs as good as it looks: “This is the baddest little .22 LR trainer ever. I’m stoked about it. With the barrel length and can, it’s the exact length of my regular comp rigs.” With length, balance, and ergonomics near identical to Bryan’s centerfire competition rifles, this 40X is a superb training tool.
Many readers wanted to know about the bottom metal and the detachable box magazine. Bryan Sike reveals: “The magazine setup is designed specifically to replicate my actual competition rifles. The bottom metal is for use with AI magazines and uses a standard M5 type inlet just like any centerfire completion rifle. In this case with the .22LR, Mike Bush designed a high reliability rimfire magazine using the same outside dimensions as an AI magazine. This rifle was built no different from any other. The action was modified and trued, barreled, fully bedded, etc. using ALL components common to centerfire match rifles.” The Rem 40X action was modified by Modacam Custom Rifles to work as a repeater with box mags.
Bryan adds that a new rimfire action is in the works: “My preference is modified Remington 40X actions and the [Vudoo Gunworks V-22 Action]. Both of which are TRUE repeaters and don’t feed from a Savage magazine. This rifle feels nothing like a .22 LR and that was the whole point.”
Why You Need a .22 LR Tactical Cross-Trainer
Many guys who shoot long-range tactical matches practice with .22 LR rifles of similar configuration. Rimfire ammo is way more affordable than centerfire, you do not need a big range facility, and shooting rimfire saves wear and tear on your centerfire rifle. Further, for learning how to read the wind, there really is no better training tool than a .22 LR, even as close as 50 yards.
Our Friend “DesertFrog”, who shoots tactical matches in Southern California, explains: “I used to shoot an average of 200 rounds of .308 Match ammo a month for training (50 per weekend). These days I shoot maybe an average of 50 rounds of .308 Win per month and probably around 600 rounds of .22 LR. Using mainly the .22 LR for practice did NOT hurt my standings in actual competitions. I shot my .308 just as well in matches, but saved the cost of hundreds of rounds of .308. If I didn’t reload and was still buying boxes of Federal Gold Medal Match .308 Win [at $1.75/round], this would be a savings of [$262.50 per month on the centerfire ammo (150 rounds).]” Money saved is money earned.
Targets for Rimfire Cross-Training
SPECIAL BONUS–Rimfire Tactical Precision Targets
These FREE targets by DesertFrog are offered in Adobe Acrobat format for easy printing. CLICK HERE to download all six targets as a .ZIP archive.
Share the post ".22 LR Tactical Trainer — Building a Top-Flight Rig"
Paul Phillips is a past King of 2 Miles, and one of the world’s top Extreme Long Range (ELR) Shooters. He recently showcased one of his ELR rifles that shoots the .416 Barrett cartridge with huge, 550gr Cutting Edge bullets seated in CNC-machined RCC (Robertson Cartridge Company) brass that costs $10 per case.
Even with these giant-sized cartridges, Paul Phillips is getting remarkable accuracy. He recently went out to a snow-covered rifle range to do some testing. We include some test results in this article. Paul’s rig delivered 1.056″ to 1.748″ 3-shot groups at 500 yards. That’s .202 to .335 MOA for three shots. (1 MOA = 1.047″ at 100 yards, or 5.235″ at 500 yards). That’s very impressive accuracy for such a big cartridge with serious recoil.
Confidence is Gained from Consistent Accuracy
Report by Paul Phillips
After being retired from my 30 years of service in military and law enforcement, I started my own company, Global Precision Group LLC. We specialize in Long range shooting. I am currently doing some R&D for a new ammunition company, Ultimate Ammunition, (UA) out of Las Vegas. UA specializes in Military, Law Enforcement, and Custom ammunition.
On this particular day, it was a very cool 15 degrees F. I was testing ammunition for the .416 Barrett. Since winning the King of 2 Miles in 2019, my team has been looking at ways to make everything better. The competition is fierce and everyone is getting better and better. Finding single-digit Standard Deviations (SDs) is a must. Holding SDs under 5 FPS can be what it takes to win.
After several weeks of testing, I think I found the perfect combination for the .416 Barrett in my rifle. My optimal load runs about 3000 FPS using the following components:
Cutting Edge 550 Grain Solid Bullets with Tips
RCC Brass (CNC-machined)
Vihtavuori 20N29 Powder
RWS primers
Loaded for ~3000 FPS load velocity goal
I figure if I can keep my 3-round groups under two inches consistently, I have a chance to win on any Sunday. The average group size of these groups was 1.47 inches at 500 yards. With big bore rifles it gets very costly to test. That is why I am limiting my test groups to 3 rounds. See below:
Note the single-digit Extreme Spread and SD for all of these three-shot groups, as recorded by the LabRadar (see below). The average SD for these three groups at 500 yards was about three.
NOTE: This is an animated GIF with THREE images, alternating every 4.5 seconds.
Not just the ammunition deserves credit. I also have to give credit to the quality Manson reamer, BAT action, Bartlein Barrel, Bix’N Andy trigger, Manners ELR stock, Nightforce Optic, and Accu-Tac bipod with my new P skis. All these gear/hardware items, combined with quality ammunition, allow these kind of groups.
Products featured in this article include:
Accu-Tac Bipods
Bartlein Barrel
BAT Machine Action
Bix’N Andy Trigger
CROSSTAC Shooting Mat
Cutting Edge Bullets
Edgewood Shooting Bag
Kestrel with Ballistics
LabRadar
LongShot Cameras
Manners Composite Stock
Manson Precision Reamer
Nightforce Optics
RCBS Press and Tools
RCC (CNC-machined) Brass
Vihtavuori Powder
The 6mm Dasher wildcat cartridge is very popular among competitive benchrest shooters, varminters, and even PRS competitors. So this Sunday we thought we’d showcase a matched Duo of Dasher rifles belonging to a Forum member Chuck L. (aka “Ridgeway”). The 6mm Dasher began as a wildcat improved version of the 6mmBR Norma cartridge. The Dasher has been very successful in competition, and now factory Peterson 6mm Dasher brass is sold by Grafs.com. (But out of stock currently.)
Chuck has a prize pair of 6mm Dashers for competitive benchrest and varmint matches in Pennsylvania. Both guns feature Kelbly Panda RBLP actions, Bartlein 8-twist barrels, and Shehane Laminated Tracker Stocks. However, the two rifles are not exact twins, as you can see. One, which we’ll call the Big Dasher, is built on a Shehane ST1000 Tracker stock. The other gun, the Small Dasher, sports Shehane’s “Baby Tracker” stock — a design used with great success by Richard Schatz. The Big Dasher, optimized for 1000-yard competition, has a slightly longer freebore — 0.136″ vs. 0.104″ for the Small Dasher.
Specifications for the Dasher Duo:
Small Dasher (13.5-pounder): Chambered for 6mm Dasher with approximately .104 freebore and a .264 NK. (No way of knowing exactly since its freebore was set in a separate operation by Kelbly.) Components are: Shehane Baby Tracker laminated stock, Kelbly Panda RPLB action, Bartlein 1:8″ LV barrel at 26 ¾”, Kelbly Rings, Weaver T36, Jewell trigger. The barrel was chambered by Kelblys and the stock was bedded, glued and balanced by a shooting buddy (Forum Member johara1). Chuck clear-coated the stock with auto urethane. Total weight is 13 lbs., 4 ounces.
Big Dasher (1K Light Gun, 17-pounder): Chambered for 6mm Dasher with a .136 freebore and .264 neck (PTG Reamer). Components are: Shehane ST-1000 laminated stock, Kelbly Panda RPLB action, Bartlein 1:8″ HV 5R barrel at 28″, Shehane +20-MOA rings, Nightforce NXS 12-42x56mm, Jewell trigger. The barrel work, pillar installation, and bedding was done by Dave Bruno. The stock was clear-coated by Chuck with auto urethane. Chuck also made the rear butt plate and balanced the rifle. Total weight: 16 lbs., 13 ounces.
Chuck tells us: “I don’t get out shooting competition as much as I want due to time and family, but when I do compete, I shoot a Groundhog match at Southfork Rifle Club in Beaverdale, PA. Info on Southfork Club events can be found at Southforkrifleclub.com. The Southfork match is basically a 100-, 300- and 500-yard match with one sighter the entire match and 5 shots at each yardage for score. The Small Dasher, with the shorter ‘Baby Tracker’ stock, was set up for the Southfork Rifle Club’s ‘Light Unlimited’ class which has a 13.5-lb max weight.” (Editor: ‘unlimited’ is a misnomer for a weight-limited category.)
Chuck adds: “The Big Dasher with the heavy ST-1000 stock is set up for 1000-yard benchrest matches in Light Gun class. I shoot 1K matches with it at Reade Range in southwest Pennsylvania. One ironic thing is, it shoots the same load I’m shooting out of the lighter gun rather well. The only difference between the two chambers is the freebore is roughly thirty thousandths longer on the 1K gun (Large Dasher). I will also shoot this at Southfork in the ‘Heavy Unlimited’ class.”
Both Dashers Group in the Ones at 100 Yards
Chuck favors 107gr Sierra MK bullets in both Dashers. Other components are: Reloder 15 powder, Lapua cases, and CCI 450 primers. His main load for the Small Dasher is 33.0 grains of Reloder 15. This load shoots in the ones at 100 yards. For the Big Dasher Chuck reported: “I’m still working on a load, although the same 33.0 grain load shoots in the ones in the heavier gun as well. I’m still looking for more velocity and my ‘max’ node.”
Dasher Brass — Three Options
1. Buy Peterson 6mm Dasher Brass
In years past, you had to create your own Dasher brass, by fire-forming (with or without projectiles), or by hydro-forming. However, Peterson Cartridge recently introduced factory-made 6mm Dasher brass.
If you do not want to waste time with fire-forming or hydro-forming, you can look for Peterson 6mm Dasher brass. This is excellent quality brass that has earned stellar reviews from purchasers. The price — $56.99 for 50 cases at Graf’s (i.e. $1.14 per case) — is nearly the same as what you’d pay for Lapua 6mmBR brass, which is $116.99 for 100 cases or $1.17 per case. The advantage is that you save time, barrel life, and you won’t lose any cases to split necks. Peterson brass can be ordered from Grafs.com. Graf’s is currently out of stock, but they should have more in a few weeks.
2. Fire-Form Dasher Brass with Bullets Hard in Lands
Chuck fireforms his Dasher brass for both rifles. Because he has a tighter-neck chamber, he neck-turns the brass first: “To fireform, I turn my cases down to fit the chamber and stop where the false shoulder makes snug contact with the chamber. Fire-forming rounds are loaded up with a 29-grain charge of H4895 or Varget and a 108gr Berger bullet seated hard into the lands about 0.020″ past initial contact with the rifling. It takes about three firings to make a nice clean Dasher case with a sharp shoulder.”
Chuck anneals his Dasher brass regularly to help maintain consistency: “I anneal about every 3-4 firings. I have many cases that have about 10+ firings on them and they are still shooting well. The primer pockets are a little looser, but still hold a primer.”
3. Have Darrell Jones Hydro-Form Your 6BR Brass to 6mm Dasher
DJ’s Brass can hydro-form a wide variety of cases for a modest fee
Fire-forming all your own 6mm Dasher brass takes time, costs money (in bullets and powder), and consumes precious barrel life. Well there IS a better solution — you can have your new brass hydro-formed by DJ’s Brass to your exact specifications for a $60.00 per hundred, which includes annealing.
DJ’s Brass Service now offers custom case hydro-forming to your exact specs. Darrell Jones offers this service for a variety of popular cartridges: 6 PPC, 30 PPC, 30 BR, 6 BRA (BR Ackley), 6mm Grinch, 6 BRDX, 6 BRX, .260 Ackley, .284 Shehane and of course the very popular 6mm Dasher. After hydro-forming your brass, Darrell can also neck-up or neck-down the cases to meet your needs. He can also turn the necks to your specs for an additional $0.60 per case.
Share the post "Sunday GunDay: Dasher Duo for Benchrest and Varmint Matches"
Today we feature a top-flight tactical .22 LR rig belonging to Jonathan Ocab. A talented Highpower marksman with the Distinguished Rifleman Badge, Jonathan also enjoys rimfire tactical disciplines which he features on his Youtube Channel. Jonathan now runs a monthly NRL22 match in California. His interest in the NRL22 game started with a CZ 455, but soon he stepped up to the impressive rig you see here. This boasts all top-tier components: Vudoo V-22 mag-fed action, Bartlein barrel, MPA Chassis, and Kahles K525i scope. Jonathan carefully selected all this hardware and assembled the rifle himself.
My Vudoo/MPA Rifle for NRL22 and Long Range Rimfire Report by Jonathan Ocab,Ocabj.net.
I became interested in rimfire shooting due to not having as much access to longer distance ranges, and the emergence of NRL22 matches. Back in 2017 I had acquired a CZ 455 and ran it in NRL22 club matches. It worked well, but as I started spending most of my time on my club’s rimfire range, I focused on getting a Vudoo Gun Works V-22. The Vudoo V-22 appeared to offer a true repeater that had the feel of a full-sized centerfire rifle along with high accuracy/precision potential.
After a lot of research, I decided to put in an order for a barreled action and acquired a Vudoo Gun Works V-22 action with a 20″ Bartlein barrel, 1-16″ twist, and MTU contour, all in Flat Dark Earth Cerakote (along with a +30 MOA base). I then acquired the TriggerTech Diamond Trigger Pro Curved, Masterpiece Arms BA Comp chassis (in Flat Dark Earth), American Rifle Company M10 34mm rings (28mm height), and Kahles K525i 5-25x56mm SKMR3 LSW scope.
CZ as a Starter NRL22 Option — The CZ 450-series is a solid family of .22 LR rifles, but I wanted to see what existed beyond the CZ level of rimfire rifles. One of my complaints with the CZ 455 is that the trigger leaves much to be desired even with the trigger kits available. Since the Vudoo V-22 action has a Remington 700 footprint and can accept most Rem 700-compatible triggers, I can actually run a top-tier trigger that would exceed anything available for the CZ.
Component Selection for the Ultimate NRL22 Competition Rifle
My choices in components were biased due to my prior experience — I went with quality hardware I knew and trusted…
Barrel Choice — I chose the Bartlein barrel over Vudoo’s in-house Ace barrels because I run a Bartlein barrel on my 6mm Creedmoor rifle and I have become a big Bartlein fan. Secondly, I chose the Masterpiece Arms BA Competition chassis because I also run the MPA BA Comp on my 6mm Creedmoor rifle. You can see the two rifles side-by-side below:
You are not seeing double. There are two rifles, both with an MPA Comp BA chassis, and both weighing about 15 pounds. In front is the featured Vudoo-action .22 LR rimfire rig with 20″ barrel, while behind is Ocab’s ARC Mausingfield 6mm Creedmoor PRS/NRL centerfire rig with 24″ barrel.
After running this rifle build for over a year now, I can say that I am more than happy with this platform as I have it configured. Having a .22 LR rifle in the same chassis as my 6mm Creedmoor rifle makes me feel right at home behind either rimfire or centerfire platform. My Vudoo V-22 weighs 15.2 lbs with Atlas CAL bipod while my 6mm Creedmoor rifle build weighs right at 15.0 lbs with the same Atlas CAL bipod. The “feel” and handling of my Vudoo V-22 MPA is as close to a centerfire gun as you can get.
Scope and Rings — I chose the 5-25x56mm Kahles K525i SKMR3 LSW because I was interested in running the Kahles after handling a few K624i and K525i scopes and hearing about how great they tracked. I run ARC M10 rings on several rifles because I think they are superbly designed.
Trigger Choice — I chose the TriggerTech Diamond because I already have a TriggerTech on one of my centerfire platforms and I wanted to try their Diamond trigger on a gun.
Outstanding Accuracy with Multiple .22 LR Ammo Types — Lapua and SK
My .22 LR ammo of choice is Lapua Center-X. This is the most commonly-chosen ammunition among Vudoo V-22 shooters. I also had good results with SK Rifle Match and Lapua Midas+ in casual 50-yard and 100-yard testing but have stayed with Lapua Center-X because my rifle shot all the lots of Center-X I put into it equally well out to 200 yards.
SUMMARY — The Vudoo V-22 and MPA Package Is Outstanding
I can hands down recommend the Vudoo Gun Works V-22 for anyone who is interested in getting one. The “full-sized” rimfire rifle segment is not a one-horse race anymore and there are other options out there, but I feel very few will regret going with a Vudoo V-22 over another alternative. If you do not have a centerfire rifle designed for NRL/PRS style of shooting, you could probably just opt to go with a CZ 457 or Tikka T1x and have a lot of room to modify and tailor those rifles to your own tastes and still have an accurate rifle for NRL22. But if you also run a precision centerfire rifle, you should seriously consider a Vudoo V-22 or other 700-pattern rimfire action if purchasing a new .22 LR rimfire rig.
My Vudoo Gun Works V-22 build is an all-purpose gun for me. It is setup for NRL22-style matches but can be utilized for (extreme) long range .22 LR shooting (300 yards and beyond). For that rimfire ELR Game, I am seriously considering getting a Vudoo V-22S (single-shot) action to put in an F-Class stock to have a dedicated ELR .22 LR gun. While I built my Vudoo Gun Works V-22 with NRL22 in mind, I realized this gun could do more so I took it out to shoot 300 yards. After that, I stretched it out to 400 yards and then 500 yards in subsequent range visits. Now I am intrigued by extreme long range .22 LR shooting and often shoot 400 yards and beyond with the Vudoo V-22 when I can.
Long Range .22 LR Rimfire — Out to 500 Yards
Jonathan shoots his competition rifle in Long Range Rimfire matches with targets out to 500 yards. That’s definitely Extreme Long Range for the little .22 LR cartridge, requiring 27.8 MILs of up elevation! Jonathan notes: “I originally had a +30 MOA base on my rifle and it worked fine to 400 yards, but I ran out of adjustment on the K525i to get to 500 and had to hold over. I ended up getting a +40 MOA base.”
NRL22 Competition — Tactical Rimfire Matches
The NRL22 match format is a great shooting discipline. NRL22 offers a high fun factor at relatively low cost. You don’t have to reload match ammo. A couple of 50-round boxes of .22 LR ammo will get you through the match. While some people bring lots of gear to matches, that’s by choice and not by necessity. You can keep it simple and still be competitive (and win).
Tips for NRL22 Competitors
I am a match director at my gun club and run our local NRL22 matches. People often ask me for tips for competing in NRL22. First, I recommend getting the course of fire for the month in advance and practicing those stages at the range. Here are other specific tips that should help NRL22 competitors improve their gun-handling and match results.
1. Dry Fire Practice — If you are not able to do live fire practice at the range, I encourage shooters to practice their shooting positions at home via dry fire. Setup props or barricades with pasters or other faux targets on a wall in the garage or inside the house and run through each stage.
2. Scope Magnification Level — The most common issue I see with newer shooters in NRL22 is the tendency to maximize their scope magnification. The timer will start, and the shooter gets into position on a target, but the scope is set to 15x or higher and the shooter can’t find the target. The shooter lowers the magnification, locates the target, and then increases the magnification again, takes the shot, transitions to another target, and repeats the process of decreasing magnification, locating target, etc. Novice NRL22 shooters should try using the mid-range magnification. Try shooting 7x-12x and learn to balance field of view and target image.
The author at NRL22 Match at West End Gun Club in San Bernardino, CA.
3. Support Side Shooting — NRL22 matches often include support-side shooting stages. This requires you to shoot with your opposite (non-dominant) hand and eye. I often hear people complain about shooting support-side. My only real tip for this is to actually spend time at the range shooting this way. Practice makes perfect. It’s all a question of learning how to shoot again and using fundamentals. Learn to get a consistent cheek weld and consistent eye relief. If necessary, figure out if you need to set your scope’s diopter for your opposite eye and mark it on the scope.
4. Tripod Practice — Even though tripods are not used in the NRL22 courses of fire, I practice shooting off of a tripod often. I will often setup targets at various distances and spaced far apart to run drills firing shots on each target with the goal of speeding up transitions and target acquisitions. Target acquisition after transition from target to target is where time is lost, so it is good to become efficient in this area.
Share the post "Sunday GunDay: Jonathan Ocab’s Vudoo/MPA .22 LR for NRL22"
Area 419 is a top-tier manufacturer of reloading tools, shooting accessories, rails, suppressors, mag kits, and tactical/PRS rifle packages. To celebrate the 4/19 date which matches its company name, Area 419 is running a very compelling SPECIAL SALE. Right now you can save 10% on CZ tactical rifle builds, save 10% on suppressors, save 15% on select actions, save 20% on TriggerTech triggers, and save 50% on apparel.
In addition, during this special sale, pretty much everything else Area 419 sells is at least 10% Off. To take advantage of these big discounts, visit Area419.com and use CODE 4192020 during check-out. (NOTE: Some items, such as the TriggerTech triggers, are already discounted, so no check-out code is required). This sale runs through 11:59 pm ET on 4/20/20.
Share the post "Big Area 419 Sale — Save 10% to 50% on Great Products"
New Cartridge, New Rifle for the King
Paul Phillips is the reigning King of 2 Miles. The founder of the Global Precision Group, Paul is one of the top ELR marksmen on the planet. He has also been a team-mate of past K02M winners.
Paul recently put together a new rifle for the 25-lb max, .338 caliber-or-under ELR Class. This is chambered for the 33XC, an efficient new cartridge devised by 11-time National HP Champion David Tubb. With promising initial testing at 500 yards, it looks like Paul’s 33XC project will be a success. The rifle’s first match will be the NRA Extreme Long Range Championship, to be held August 21-23, 2019 at Camp Atterbury, Indiana.
Paul reports: “The 33XC is ready for the NRA ELR Nationals. I have tested loads from 3100-3450 FPS and and will settle on a load around 3250 FPS [which is] my most accurate load so far. The Peterson Cartridge brass is really working well.”
Paul states he would like to look for a higher node from 3300-3400 GPS: “Next stop is with the Applied Ballistics LLC mobile labratory and radar testing with a PDM for the Nationals.” Paul cautions: “I encourage everyone to start low and work up. Every chamber, barrel, and components are a little different.”
During initial testing, Paul’s 33XC put three shots in 0.27″ at 100. Then, at 500 yards, the rifle produced a 3-shot group around 1/3-MOA with just 1.22 inches of vertical. That’s pretty impressive for early testing. Paul will also be trying some Berger bullets soon. When he determines the most accurate load, Phillips will stretch the rifle’s legs, shooting out to 2500 yards and beyond.
Quote: “The Cutting Edge Bullets are not the highest BC but they are very stable and consistent at ELR (sub-sonic) ranges and that’s the most important factor in finding the best ELR bullet. I actually test all my bullets at sub-sonic speeds to make sure they are consistent and stable. Finding a good load at 500 yards is just the first part. The real test is shooting them at sub-sonic speeds and see how consistently they group. This is what gives you the highest percentage to impact at 2 miles and beyond.”
This rifle features a BAT action mated to a 34″ Bartlein barrel chambered for David Tubb’s new 33XC cartridge. Paul Phillips is currently running Cutting Edge 275gr Lazer solid bullets. Paul notes: “I also have a .338 Lapua Magnum barrel and 300gr Berger bullets for the restricted class in France.” Paul gave special thanks to Alex Wheeler for doing the metal work and Alex Sitman for doing the bedding.
Rifle Component List
Action: BAT Machine CTH dual-port action
Trigger: Bullet Central Bix’N Andy
Barrel: Bartlein 1:8″-twist barrel (34″)
Chambering: 33XC for Peterson brass
Stock: McMillan A6 Super Mag, Bedding Alex Sitman
Scope: Nightforce Optics 7-35x56mm F1 ATACR.
Bipod: Duplin Rifles
Paul Phillips notes: “Alex Sitman has been bedding rifles stocks for most of his life. I believe that [bedding] is a very important … to keep consistent accuracy and repeatable zeros after traveling all over the globe.”
Even with the TacomHQ Charlie Tarac scope prism in place, the rifle makes the 25-pound weight limit with Duplin Rifles bipod. Paul says: “I love it when a plan comes together!! I’m under by 2 ounces!”
About the 33XC (eXtra Capacity) Cartridge
David Tubb invented the 33XC cartridge because he thought the CheyTac cases were too much trouble — requiring a larger action, oversize presses, and ultra-expensive dies. The 33XC was designed to fit .338 Lapua Magnum-size actions and use normal reloading presses.
The 33XC (eXtra Capacity) has 137.5 grains of H2O capacity with over 125 grains of usable powder capacity while leaving the 0.393″ neck unfilled for bullet seating.
The 33XC has a .338 Lapua Magnum lineage. Think of it as a better, 35°-shoulder .338 LM. David explains: “The 33XC uses standard reloading dies along with a 7/8″ x 14 TPI reloading press. There is no fire-forming — all case ‘improving’ has already been done with a production case that has 20 grains more powder capacity, 35-degree shoulder, and longer neck compared to a .338 Lapua Magnum. This puts the various .338 Lapua wildcats and the Rem Ultra Mag Improved into the ‘also ran’ category. They simply can’t compete with the velocities attainable with the 33XC.”
The 33XC is based off of a .580″ bolt head. Tubb states that “A fired case will extract with little effort when using a properly-polished chamber with a maximum powder charge after resizing with the Superior Shooting Systems FL sizing die.” Tubb’s 33XC die reaches the case head which is important for accuracy. Peterson Cartridge produces the 33XC brass for Superior Shooting Systems. This high-quality brass costs $115 for 50 cases (or $2.30 per case), and can be purchased directly from Superior Shooting Systems.
Share the post "Sunday GunDay: New 33XC Rifle for Reigning King of 2 Miles"
33XC — Popular ELR Cartridge
Optics and Rings
After several weeks of testing, I think I found the perfect combination for the .416 Barrett in my rifle. My optimal load runs about 3000 FPS using the following components:
Fire-forming all your own 6mm Dasher brass takes time, costs money (in bullets and powder), and consumes precious barrel life. Well there IS a better solution — you can have your new brass hydro-formed by 
