While 100/200 yard benchrest competitors have been drilling tiny groups at the Kelbly Super Shoot this week, other folks, with MUCH bigger rifles, have been shooting at very long range in Raton, New Mexico.
This week the NRA Whittington Center at Raton hosts the Fifty Caliber Shooting Association (FCSA) annual Extreme Long Range (ELR) Record Match. Some of the most talented long-range shooters on the planet are there, including past King of Two Miles Derek Rodgers, along with his Team Global Precision team-mates Mark Lonsdale and Paul Phillips.
Here is Mark preparing to shoot on the first day of the FCSA 1.5 Mile ELR Match with Paul and Derek spotting and calling wind. The cold bore 10″ gong was at 1,040 yards and all three men nailed it. From there the six steel targets ranged from 1,180 yards, up the side of the mountains, to over 2,600 yards.
Site of Day 1 for the FCSA ELR match at Raton, NM. Targets at 2,300, 2,585, and 2,725 yards. Weather cleared up but wind was brutal.
After Day 1 of the FCSA 1.5 Mile ELR match, Derek was in 2nd place, Mark in 3rd, and Paul in 5th. Mark reported: “Today we had winds gusting well over 15 mph from 6 o’clock, but as they hit the base of the mountains, they created an updraft that caused shots out past 2,000 yards to go high. But just when you had that wind doped, it would switch to a gusting 9 o’clock (left to right) pushing bullets 20 feet to the right. A very challenging day but good practice for Ko2M next month.”
These gents are shooting big rigs with jumbo-sized cartridges. Mark is campaigning a .416 Barrett with Cutting Edge Bullets. Below is his ELR rifle, which features jumbo BAT action, Bartlein barrel (with brake), McMillan stock, and Nightforce scope. Mark posted: “Getting the .416 Barrett ready to shoot in the FCSA 1.5 Mile ELR Match. Weather is definitely warmer than yesterday’s match but wind is howling today.”
TECH TIP — Barrel Life in the ELR Game
Mark Lonsdale posted this interesting commentary on barrel life in the ELR game: “How long a barrel lasts has a lot to do with how hot you run your loads and resultant chamber pressures, but it can also be poor cleaning technique. That said, if you are into ELR or long range precision shooting, and you shoot a lot, you need to think of match-grade barrels as a consumable item — just like the tires on your car. You change your tires when they show excessive wear, so you change your barrel when the accuracy drops off. Similarly, you buy tires that best suit your needs, street or off-road, so you buy a barrel that meets your requirements for weight, accuracy and muzzle velocity.”
“Accuracy is also subjective based on the needs of the shooter. Hunting big game does not require the same pin-point accuracy as long range varmint hunting, and having fun at local club matches does not require the same accuracy as aspiring to be a national champion. With accuracy comes cost, but when compared to the cost of ELR ammo in .338, .375 or .416, a new barrel is actually an affordable consumable. Just remember, ‘the only good rifle is an accurate rifle’.”
Share the post "ELR Shooting at Raton, New Mexico — Out to 1.55 Miles"
The Three Amigos in New Mexico (L to R): Kelly McMillan, Paul Phillips, Derek Rodgers.
This isn’t your typical hunting story, because these aren’t your typical hunters. Derek Rodgers is the current F-TR World Champion, and past King of Two Miles. Paul Phillips was a member of the Silver Medal-winning F-TR Team McMillan at the 2018 Nationals. Paul also shoots with Team Applied Ballistics in ELR competition. The third hunter, Kelly McMillan, needs no introduction. The respected owner of McMillan Fiberglass Stocks, Kelly has been a leading figure in the gun industry for years. He also supports many top rifle shooting teams.
This talented trio recently got together for a very successful hunt in New Mexico, Derek’s home turf. All three men bagged an impressive Antelope, with Paul Phillips dropping the biggest buck of all. Derek made the longest shot, hitting his buck at an impressive 510 yards, verified by laser rangefinder.
Paul Phillips posted: “Our New Mexico Antelope hunt with Kelly McMillan and Derek Rodgers was a success. To hunt with these two icons was definitely on my bucket list. I shot my buck at 389 yards in an 18-mph wind through a barbed wire fence. It may be a possible Boone and Crockett trophy buck, measuring 84 3/8 inches.”
Derek nailed his Antelope at 510 yards with a .308 Win fitted with a GSL Technology suppressor. As dusk approached, despite blustery wind and rain, Kelly dropped the third Antelope with a great 230-yard shot from a broken tree crotch. Paul noted: “All three bucks had their own challenges and funny story. All three hunts required team work with stalking, communication. For all three shots we used Applied Ballistics LLC solutions with our Kestrels for data.” The three men used all top-quality products including McMillan stocks, Bartlein barrels, Stiller actions, Berger bullets, and Nightforce scopes.
For long-range hunting you need to have your drops absolutely “spot-on”. Paul posted: “When you do a 30-45 minute stalk… you need to have all your ballistics perfect or they get away. We were glad that we had a practice day before the hunt to confirm our zeros and verify our ballistics.”
Kelly notes: “Paul Phillips scored this nice 80+” buck in New Mexico. It was Paul’s first antelope.” The .338 LM rifle featured a Stiller TAC338 action, Bartlein 20″ barrel, McMillan A5 Stock, and Nightforce ATACR scope. In the Facebook video, Paul talks about making the shot, directly into the wind.
Share the post "Shooting Superstars Go Antelope Hunting in New Mexico"
The 2018 King of 2 Miles (KO2M) event took place July 2-4 in Raton, New Mexico. Conditions were very challenging this year, yet three shooters managed to hit the most distant 3,525-yard plate at least once in five shots, a remarkable accomplishment. At that range the bullet was in flight about six seconds.
Robert Brantley of Team Manners Composite Stocks is the new King of 2 Miles. Congrats to Robert and his team-mates. Robert amassed 85178 points, finishing over 20,000 points ahead of runner-up John Buhay. Paul Phillips of Team Applied Ballistics finished third. FULL K02M 2018 RESULTS HERE.
Here’s Robert Brantley after his superb qualifying performance, which set a new 2018 King of 2 Miles qualifying round record. Going perfect on targets 1, 2, and 3, Robert missed just one shot on Target 4 of the qualifying phase, amassing 51355 points, a new K02M record.
CLICK HERE for a very complete and thorough KO2M report created by The Precision Rifle Blog (PRB). This excellent PRB Report contains complete load and rig specifications for the top five shooters. In addition, the PRB Report includes a full run-down on this year’s event.
Though the trigger pullers get the glory, this is really a three-man game. One guy shoots, a second team member spots for hits and calls corrections, and a third watches mirage and makes wind calls.
Multi-Day, Multi-Distance Competition with Farthest Target at 3525 Yards
The K02M Competition runs in stages, with the distances getting farther with each round. After five shots on target 1 at 1547 yards, there are then three shots per target for the remaining three parts of the Qualifying round. Then, in the three-target Finals phase, there are with five shots per target. You get more points for earlier hits in each string, and there are no sighters during the match. The event started with a tough Cold Bore Challenge — a single-shot at 1689 yards, just shy of one mile. Only three out of 62 competitors made that cold-bore mile shot on a 16″ plate, about 1 MOA at that distance. After that there are two rounds with the targets arrayed as follows.
KO2M Qualification Round
1,547 yards: 5 shots, 24” x 37” rectangle
1,719 yards: 3 shots, 24” x 37” rectangle
1,890 yards: 3 shots, 30” x 37” rectangle
2,095 yards: 3 shots, 30” x 37” rectangle
KO2M Finals Round — July 4
2,727 yards: 5 shots, 33” x 41” rectangle
3,166 yards: 5 shots, 42” x 54” rectangle
3,525 yards: 5 shots, 48” x 60” rectangle
Big Bore Rifles with High-BC Bullets
This year saw the continued evolution of equipment. Top shooter Brantley shot a .416 Barrett with 500gr Cutting Edge bullets. Robert’s massive 44-lb rifle featured a 39″ K&P barrel, McMillan action, and a Manners LRT (Long Range Tactical) stock designed expressly for this KO2M competition.
Second Place John Buhay shot an improved version of the .375 CheyTac, with 353gr Lehigh Defense Match Solid bullets. Buhay’s 37.6-lb rig bosted a BAT action and 36″ Krieger barrel along with a fairly conventional McMillan MBR 1K benchrest stock. Mark King built the rifle.
Third Place Paul Phillips campaigned a .416 Barrett with 550gr Cutting Edge Lazer bullets. Paul’s 42-lb rig featured a BAT action and McMillan Beast 1 stock. Shown below is the latest rifle of 2017 K02M champ Derek Rodgers, a .416 Barrett also in a McMillan Beast. Derek spotted for Phillips in the match.
Optics Options
There was quite a variety of scopes used by Top K02M competitors, evidence that a number of manufacturers now offer optics with abundant elevation and the ability to stand up to heavy recoil. Here are the optics choices for the Top Five Shooters:
1. Bushnell XRS II 4.5-30x50mm with G3 reticle in Badger UniMount
2. Nightforce ATACR 5-25x56mm with MOAR reticle, with ERA-TAC Inclined Mount
3. Nightforce ATACR 5-25×56mm, with Charlie TARAC external Prism System for Elevation
4. Leupold Mark 5HD 5-25×56mm, in Spuhr mount with Charlie TARAC
5. Burris XTR II 5-25x50mm in Barrett rings
Notably, two of the top five used the Charlie TARAC prism system. This provides a ton of extra elevation by essentially shifting the view seen through the scope. The unit fits to the scope’s front objective.
Share the post "2018 King of 2 Miles (KO2M) Highlights Report"
Current F-TR World Champion Derek Rodgers is also the reigning King of 2 Miles champ, so he knows something about Extreme Long Range (ELR) shooting. While Derek won his KO2M title at Raton shooting the .375 CheyTac cartridge, Derek decided that something even bigger was in order. This season, Derek will be shooting a .416 Barrett. Last week we showcased his impressive .416 Barrett ammo, with massive Cutting Edge bullets.
Now we can show the Big Rig that will deliver those .416-caliber projectiles. This monster weighs 40+ pounds and sports a 40″ Bartlein barrel — more length for more velocity. Derek’s new ELR rifle features a McMillan Beast 2 stock, BAT EX action, and Nightforce ATACR 7-35x56mm scope. Derek explained why he moved up to a bigger caliber: “I built a new rifle with the anticipation of seeing impacts easier. It was not just a larger caliber being more effective on hitting ELR targets, but rather hoping that a missed shot would have a much larger impact. Impacts beyond a mile become harder to see due to terrain and vegetation. So any added dust or splash erupting from the earth is a decisive benefit over an equally-accurate smaller caliber.” Here is Derek’s full report on his new .416 Barrett rifle.
Derek Rodgers Campaigns a .416 Barrett
Report by Derek Rodgers Cartridge Choice — I chose a standard .416 Barrett cartridge as it allows for bullets up to and slightly exceeding 550 grains. It really does bridge the gap between the .375 variants and a 50 BMG. There are several great solid ELR bullet options from manufactures like Cutting Edge that range from 475-550 grains. These offer a variety of extremely high BC options for barrels that have different twist rates. Most loads will utilize the slowest burn rate powders commercially available. Good options are Vihtavuori 20N29, RL50, H50BMG and other powders with a similar burn rate.
Shooting the .416 — Tamer than Expected
An initial observation is that the rifle is very controllable and feels much like a larger F-TR gun. The rifle weighs 40+ pounds, balanced and stays on target very well. The recoil is manageable and linear. This seems to give a straight rearward impulse that does not affect positioning. This allows for quick repositioning into battery and faster follow-up shots.
Rifle Details — BAT EX Action, Bartlein 40″ Barrel, McMillan Beast 2 Stock
Derek’s .416 Barrett ELR Rig features a BAT EX action with a Bix N’ Andy trigger. Out front is a gigantic 40” long, 1:9″-twist Bartlein barrel fitted with a Terminator T5 muzzle brake. The handsome McMillan Beast 2 stock combines a lower center of gravity design with a higher butt location. Given that high butt geometry, McMillan cleverly fitted the higher buttpad with a port allowing the cleaning rod to pass through (see photo below). On top is a Nightforce ATACR 7-35x56mm scope in NF rings on a +60 MOA rail, with Holland 34mm bubble level. The stock is supported by a Phoenix bipod and rests in an Edgewood bag designed for the McMillan Xit F-TR stock.
Note the extended Buttpad height. That helps with recoil in prone position. This McMillan Beast 2 stock includes a pass-through hole for the cleaning rod.
Gunsmithing by Blake Barrel and Rifle in Arizona
Derek’s rifle was built and chambered by Bryan Blake of Blake Barrel and Rifle in Phoenix, Arizona. The chambering was done with a Manson Precision reamer. Derek explains: “Bryan and his family have been in the machine shop business for several generations and have the expertise and equipment to handle larger barrel diameters associated with F-Class to ELR type rigs. I tried to consider all angles and potential pitfalls that might occur during the building process. However, Bryan added his own touches to make the project his own. He truly created a work of art and supplied a turn-key rifle that is meticulously built from the inside out and looks as great as the tolerances it holds.”
Share the post "Beast for the King — Reigning King of 2 Miles Gets .416 Barrett"
Our friend Derek Rodgers is the current F-TR World Champion AND the current King of 2 Miles, having won his KO2M crown at Raton last year. Shooting with Team Applied Ballistics, Derek delivered a dominant performance at the KO2M event, scoring nearly twice as many points as his nearest rival, Ronnie Wright. And Derek was the first KO2M marksman in history to hit the target at the maximum 3368-yard (1.91 mile) distance.
Derek topped the K02M field last year shooting a .375 CheyTac with Cutting Edge 400gr LazerMax tipped bullets. That’s a really big cartridge, but apparently not big enough for Derek. Mr. Rodgers has hot-rodded his long-range rig, fitting a barrel for an even bigger cartridge, the mighty .416 Barrett. Derek tells us: “The .416 is rolling now. I am preparing for initial load development and working out tooling kinks on the bench.” He is loading more Cutting Edge bullets with a selection of slow powders. For his .375 CheyTac last year, Derek used Hodgdon 50 BMG. He’s trying something else this time…
Breakfast of Champions:
Watch Derek Rodgers hit 3368-yard target at 2017 K02M Competition:
At the 2017 K02M, Derek ruled. With his McMillan-stocked .375 CheyTac rifle, Derek shot brilliantly from the start. He was perfect — without a miss — at the first three yardages: 1543, 1722, and 1888. He had some misses at 1953 and 2667 yards, but then he out-shot all competitors at 3028 yards, going two for five. No other shooter managed a single hit at 3028 yards. Then it all came down to the big one — the last (and greatest) challenge, the target at 3368 yards (1.91 miles).
Share the post "The King Goes Big — Derek Rodgers Builds a .416 Barrett"
Derek Rodgers is the current F-TR World Champion AND the reigning King of 2 Miles. He’s also a member of the Berger SWN-winning McMillan F-TR team. But when it comes to rifles, competition is only one of Derek’s interests. He’s also an avid hunter. He enjoys getting out in the back-country in his home state of New Mexico.
Recently Derek went coyote hunting with his daughter, Dereka. They spotted some ‘yotes, but the real treat was seeing Oryx, a long-horned species native to Africa. Some time ago, a herd of Oryx was transplanted to a “secret spot” in New Mexico not too far from Albuquerque. Permission to hunt the Oryx is hard to obtain, but possible.
Derek and his daughter could not shoot Oryx on this occasion because the timing wasn’t right. But he noted: “Calling for coyotes can get exciting when your daughter has an oryx hunt just weeks away.” You can see the animals in the video below. Derek says: “It would have been a successful morning if this was March 1st [when Oryx hunting would be allowed with her tag].” Derek’s wife Hope tells us that “Oryx meat is delicious — much better than deer or elk.” Good luck to Dereka and her famous father next month.
Derek’s Coyote rifle (for this trip) was an AR-platform rig. Despite being a world-champion F-Class shooter, Derek had a number of coyote misses on this trip, which did NOT impress young Miss Dereka. It just shows that even the best can easily miss on a moving target.
Share the post "The King of 2 Miles Goes Hunting with His Daughter"
Most bolt-action rifle shooters work the bolt with their trigger-pulling hand. This is because most rifles sold to right-handed shooters come with right-side bolts, while “lefty” rifles come with left-side bolts. This “standard” configuration requires the shooter to take his dominant, trigger-pulling hand off the stock to cycle the bolt, then re-position his hand on the stock, and “re-claim” the trigger. Often the shooter must lift or move his head to work the bolt, and that also requires him to re-establish his cheek weld after each and every shot. Not good.
This really doesn’t make much sense for precision shooting with fore-end support*. There is a better way. If you leave your trigger hand in position and work the bolt (and feed rounds) with the opposite hand, then you don’t need to shift grip and head position with each shot. All this requires is a weakside-placed bolt, i.e. a left bolt for a right-handed shooter or a right bolt for a left-handed shooter. The video below shows a “Lefty” working a right bolt. Note how efficient this is:
As our friend Boyd Allen explains: “If you think about it, if you are going to work with a factory action where your options are left bolt and left port or right bolt and right port, and you are building a rifle that will only be shot from a rest, using the left/left for a RH shooter or using a right/right for a LH shooter works better than the conventional configuration”.
Shoot Like a Champ and Work the Bolt with Your Weakside Hand
Derek Rodgers, the current F-TR World Champion, the reigning King of 2 Miles, and the only person to have won BOTH F-Open and F-TR U.S. National Championships, runs this kind of “opposite” bolt set-up. Yep, Derek shoots right-handed with a left bolt. Though Derek is a right-hander, he shoots with a Left Bolt/Left Port (LBLP) action. He pulls the trigger with his right index finger, while working the left-side bolt with his left (weakside) hand. This allows him to stay in position, and maintain his cheekweld. He places his right hand on the grip, while manipulating the bolt (and feeding rounds) with his non-trigger-pulling hand.
Current King of 2 Miles (and F-TR World Champion) Derek Rodgers
This is the rifle with which Derek won the 2013 F-TR National Championship.
*For true standing, off-hand shooting (whether in competition or on a hunt), a conventional strongside bolt placement makes sense, since the non-dominant arm must support the front of the rifle all the time. When shooting from bipod or rest, it’s a different story.
Share the post "Weakside Bolt Placement — The Competitive Advantages"
There are three notable articles in the latest January 2018 Digital Edition of Shooting Sports USA Magazine. F-Class competitors will definitely want to read the report on the 2017 World Championships. And hand-loaders will appreciate the insightful article on the AMP induction annealing machine. The third recommended article provides tips and techniques for sighting in hunting, tactical, and benchrest rifles. Access the entire SSUSA 54-page January 2018 eZine by clicking THIS LINK.
F-Class 2017 World Championships in Canada Story by Larry Bartholome
Fifteen years ago, the very first F-Class World Championships were held in Canada. In 2017, the Championships returned to Canada for the fifth edition of the match. This year there were triple the number of entries, representing the growing popularity of F-Class competition. Notably, this year’s event was preceded by the Canadian F-Class National Championships. This issue contains a full report on the event, written by Larry Bartolome, a past National F-Open Champion. Shown at right above is the new F-TR World Champion, our friend Derek Rodgers from New Mexico.
AMP Annealing Machine — Annealing .30-06 Brass for Vintage Military Rifles Story by Art Merrill
Produced in New Zealand, the AMP (Annealing Made Perfect) unit is a sophisticated, microprocessor-controlled annealing machine that achieves ultra-consistent results using an electrical INDUCTION process. By contrast, with butane torch systems you may have to adjust the system when the ambient temperature changes, or even if your butane fuel is slightly different. In this month’s issue of Shooting Sports USA, Field Editor Art Merrill uses the AMP to anneal .30-06 brass for vintage military rifles. The review shows how to use the AMP and explains the advantages of the Induction Annealing vs. flame-based annealing.
Sighting In Your Rifle — Tips for All Shooters Story by Jim Shults
This month’s “Rifle Issue” of Shooting Sports USA focuses on rifle shooting in various forms. Author Jim Shults has written an lengthy article offering tips and techniques for sighting-in your rifle. Shults says “The trick in effective sighting-in (zeroing) is shot-to-shot consistency”. To achieve that consistency, you must first eliminate driver error. You need a stable set-up. Good ammo is also essential and Shults offers an important tip: “Keep your ammo cool and out of direct sun at the range”. Shults also explains there is a big difference between load testing and zeroing. You want to finalize your zero AFTER you have developed your match or hunting load.
Share the post "Good Reading — Shooting Sports USA January “Rifle Issue”"
Do you have a hankering to shoot Extreme Long Range (ELR)? Then you’ll want a large-caliber cartridge with plenty of boiler room. Some of the most successful ELR cartridges have been based on the CheyTac family, including the .375 CheyTac (9.5×77) and .408 CheyTac (10.36 x 77). Now brass for both these jumbo cartridges is offered by Peterson Cartridge. This Peterson Cheytac brass has proven to be tough and long-lived. And it is capable of winning — Derek Rodgers won the 2017 King of 2 Miles (K02M) event shooting a .375 Cheytac with Peterson brass. Here’s a report on how Peterson developed and tested its tough CheyTac cartridge brass.
Developing and Testing CheyTac Brass
Report by Peterson Cartridge Co.
Recently, our president, Derek Peterson, was live-testing our most recent iteration of the .375 CheyTac (aka 9.5 X 77). He started with five casings, and did a full-body resizing after each firing. He got 17 firings out of each before he started to notice the early signs of case head separation. [Editor: Theses were with extremely high pressure loads.] He then took another set of casings and after each firing he just bumped the shoulder back, like a typical reloader would. He got 20 firings out of those casings.
Note: CheyTac® is a registered trademark of CheyTac USA, LLC. Peterson Cartridge has no affiliation.
Low MV Extreme Spread
On the first two shots the muzzle velocities were within 12 feet per second of each other. On the 3rd and 4th shots the muzzle velocities were within 6 feet per second of each other. By the 5th shot the muzzle velocities were within 1 foot per second of each other. Now that is how you can put two bullets in the same hole down range.
No SAAMI Spec for CheyTac Cartridges
As many of you probably already know there is no SAAMI spec on these calibers. So, without a SAAMI spec there is no stated maximum pressure for a service load. However, there IS an international spec on the .408 [promulgated by the] CIP (Commission International Permanente). And the CIP max pressure for this round is extremely high. Our partner in Europe tells us it is probably unnecessarily high. Our partner loads these rounds and they have a standard load for the .375s which is also quite high. So that is the pressure we did our testing at. To even achieve that pressure, we had to use a compressed load. We are explaining all this to say that you [should not use] a load that hot, and therefor you will most likely get more reloads than we did[.]
Peterson Brass Goes Through 11 Dimensional Tests
With all the casings we make in any caliber, we perform a battery of in-process, real-time dimensional checks. [We test] 11 different dimensions continuously throughout each shift. Some of these are tube cylindricity, mouth to body concentricity, primer pocket diameter, length to shoulder, overall length, and more. These measurements are automatically fed into Statistical Process Control software. If a dimension begins to drift from nominal we can catch it immediately and correct it.
Peterson is Fully Committed to CheyTac Brass Production
Peterson Cartridge purchased additional manufacturing equipment designed specifically to produce these large casings. Our capacity is 5-million casings a year. We are committed to there not being a shortage of these calibers ever again.
Derek Rodgers is the 2017 King of 2 Miles. He is also the only human to ever hit the maximum distance target target at 3368 yards (1.91 miles). His cartridge choice? The .375 CheyTac. Derek ran Cutting Edge Bullets in Peterson brass with Hodgdon H50BMG powder.
Q: Why did you choose the .375 CheyTac cartridge?
Derek: When I was asked to join the Applied Ballistics Team, I needed to get an ELR rifle built in a short period of time. I was under a very tight time schedule to get the project complete. In an effort to eliminate variables, I decided to keep things standard and as simple as possible. I chose the .375 CheyTac for the ease of getting components. The larger rifles are more difficult to get components quickly and I felt like the .375 CheyTac had enough attributes to be competitive at ELR distances.
Product Tip from EdLongrange. We welcome reader submissions.
Share the post "Tough Brass for Big Ammo — Cheytac Brass from Peterson"
Team Applied Ballistics will soon release a new DVD on the science, skills, and strategy required for successful Extreme Long Range (ELR) shooting. The new DVD features a reality-style documentary following Team Applied Ballistics in the 2017 King Of 2 Mile (KO2M) competition. Team AB has now won this prestigious event two years in a row. Team shooter Mitchell Fitzpatrick won the KO2M title in 2016, followed by team-mate Derek Rodgers in 2017.
Bryan Litz tells us: “Applied Ballistics is proud to announce the release of our latest DVD: ELR Shooting With Applied Ballistics. With lessons learned from our successful 2016 KO2M campaign, you can see how the AB ELR team developed our equipment and approach through practice and careful analysis. Learn the essential elements of ELR competition from the top team in the sport.”
This documentary, filmed over the course of a year, shows Team Applied Ballistics preparing for, and competing in, the 2017 KO2M match. This presentation includes interviews from all Team AB members, along with tips on ELR shooting.Pre-Order the ELR DVD and Save $5.00 (Pre-Order Price $19.95)
2017 K02M Match-Winning Performance on Video
The video below shows Team Applied Ballistics shooter Derek Rodgers winning the 2017 King of 2 Miles event. This excellent video combines firing line and target-cam views. You can see the strings-of-fire at 2667 and 3028 yards. Then Watch Derek, after four misses, hit the last target with his fifth (and final) round! That plate was set at a mind-numbing 3368 yards (1.91 miles). Derek had Paul Phillips as a spotter and Emil Praslick as a wind coach — a very powerful team and it showed.
If you want to learn more about ELR shooting and how team Applied Ballistics achieves great results in ELR competition, we recommend an excellent article just released byShooting Sports USA. SSUSA’s Editor John Parker interviewed Team Applied Ballistics members Bryan Litz and Paul Phillips. Both men said that successful Extreme Long Range shooting requires solid team-work.
Bryan Litz (center) conferring with Team AB members Emil Praslick (L) and Doc Beech (R).
Paul Phillips explained: “ELR is very difficult. It requires a great shooter with 1/2-MOA accuracy, a really good wind coach and spotter to see impacts, trace and the ability to quickly negotiate and engage the targets. It’s one fluid team working together.”
Bryan Litz, Applied Ballistics founder, concurred: “Of all the various precision rifle disciplines, ELR shooting is particularly suited to a team approach. All aspects of ELR shooting are both highly challenging as well as critical to success. One individual is typically not able to stay on top of all the variables effectively enough to hit targets at extreme ranges all by themselves.”
Litz says superior wind-reading skills are vital in the ELR game: “One of the important challenges of hitting targets at long range is reading the wind. All the shooters on our team can read wind, but when we’re shooting a match, we put our strongest wind-reader in this position for all shooters. Emil Praslick is arguably the best in the world at putting a number on the wind. He’s got a well-rehearsed process that works in all scenarios. When Emil isn’t available, someone else on our team will apply his process and focus specifically on the wind.”
Share the post "Extreme Long Range — New ELR DVD from Applied Ballistics"
Hail the new F-Class World Champions: Australian Rod Davies (F-Open) and the USA’s Derek Rodgers (F-TR). The 2017 F-Class Individual World Championships event was memorable — with thunderstorms, tight competition, and wicked winds on the final day. On Day 1, Saturday 8/12/17, only one 700m relay was completed before a massive storm front dropped a deluge. Conditions prior to that were good, with dozens of competitors shooting “clean” — one competitor lamented “I didn’t drop a point but ended up way down the standings on V-Count…”
After one yardage, the FCWC was halted on Saturday (Day 1) by a massive thunderstorm.
Sebastian Lambang photo
F-TR — The King of 2 Miles vs. The Newly-Crowned Canadian Champ
The F-TR event couldn’t have been closer — this went down to the wire. American Derek Rodgers scored 473-36V to win the title on V-Count over Canadia Kevin Chou (473-31V). Kevin is a very tough man to beat on his home range in Ontario. At this same venue, Kevin recently won Canada’s F-TR National Championship, his second F-TR Canadian National title in a row.
This has been a great summer for Rodgers. Last month Derek won the King of 2 Miles competition in Raton, NM. But the World Championship F-TR win didn’t come easy. Not by a long shot. This was a tough, come-from-behind win for Derek. After Day 1, which was halted by rain, Derek was in 77th position. On Day 2, he had climbed to 17th. He moved all the way to the top of the podium on the third and final day by shooting brilliantly in very tough conditions.
Derek told us: “The wind was changing very rapidly on Monday (Day 3). There were radical changes. It was blowing left to right, but there were rapid velocity changes. You might move from holding at the edge of the black ring on the left, then over to the 2 ring on the right from shot to shot.” Derek noted that the match was “pair fire” so you had to wait up to 45 seconds for your partner to shoot. “That means you couldn’t shoot fast. You had to watch the conditions very carefully — watch those big canvas flags and the mirage.” Derek said the mirage was “huge in Canada… but it looks different than what I’m used to in the American Southwest. The mirage off grass is different.”
Many observers had counted Rodgers out when he stood in 17th place after Day 2, but he mastered the tough conditions to move up in the standings as others were dropping points in bunches. Derek said that starting in 17th might have been a blessing in disguise: “Starting 17th, I didn’t feel any pressure on the last day. Once I got the wind ‘roped’ on that last day, it was actually fun. I nailed a bunch of Vs, and that’s what carried me to victory.”
F-Open World Champion Rod Davies (Australia) Receives the Milcun Shield Trophy
Jenni Hausler photo.
Australian Captures F-Open Title with a Powerful Performance
In F-Open, the story was all Rod Davies, the talented Australian. He shot strong and steady throughout the match, to top the field with a 489-41V score. Finishing second was the UK’s Paul Sandie (485-38V), while another Australian, Adam Pohl, took third with 482-38V. Those Aussies do know how to shoot off grass in windy conditions. Five of the top 15 F-Open shooters were from Down Under. The top American was Jim Murphy in fourth place, followed by Erik Cortina in fifth.
Tough Conditions on Day Three
Erik Cortina told us that conditions were very tough on the last day. Wind velocities were changing unpredictably — with disastrous results for some shooters dropped 10 points or more. Somehow, in those rapidly changing winds, Eric nailed the top Aggregate for the last day, out-shooting the field: “I was lucky enough that conditions were very tough on the last day and that I was able to read the conditions good enough to win the Aggregate for the day. I moved up from 27th to 5th (overall) in one day. There were close to 200 of the best F-Open shooters in the World competing at this match, what an amazing experience to share the range with such an outstanding group of people.”
2017 FCWC relays were conducted with Pair Firing, with each shooter alternating shot by shot. Here are Mark Fairbairn (Australia) and Matt Schwartzkopf (USA) on the right. Sebastian Lambang photo.
YOUNG GUNS: At the 2017 FCWC the first-ever Under 25 World Champions were crowned: Mitchell Fitzpatrick (F-TR) and Rhys Ireland (F-Open). Rhys also won the 2017 Canadian National F-Open Championship last week. Mitchell is a past KO2M winner.
The young pit crew members did a great job. Sebastian Lambang photo.
Team Matches Come Next
There is a lay day today, August 15th, after which the Team Competition phase of the F-Class World Championships commence. We can expect a tough battle among the top teams: Australia, Canada, Great Britain/UK, South Africa, and the USA. Here is the schedule/course of fire for the Team Matches:
FCWC Team Competition
Wednesday, August 16: 2+15 @ 700m, 2+15 @ 800m, 2+15 @ 900m
Thursday, August 17: 2+15 @ 700m, 2+15 @ 800m , 2+15 @ 900m
Prize Giving and Closing Ceremonies
Share the post "Individual Champions Crowned at F-Class Worlds in Canada"
Photos by Stephen Fiorenzo, courtesy Applied Ballistics.
The 2017 King of 2 Miles match has concluded, and we have a new monarch. F-Class Ace Derek Rodgers is the new King of 2 Miles. Shooting with Team Applied Ballistics, Derek delivered a dominant performance, scoring nearly twice as many points as his nearest rival, Ronnie Wright. And Derek was the first KO2M marksman in history to hit the target at the maximum 3368-yard (1.91 mile) distance.
With his McMillan-stocked .375 CheyTac rifle, Derek shot brilliantly from the start. He was perfect — without a miss — at the first three yardages: 1543, 1722, and 1888. He had some misses at 1953 and 2667 yards, but then he out-shot all competitors at 3028 yards, going two for five. No other shooter managed a single hit at 3028 yards. Then it all came down to the big one — the last (and greatest) challenge, the target at 3368 yards (1.91 miles).
This would require superior shooting skills, a masterful wind call (by Emil Praslick), and nerves of steel. Derek tried four shots without success. It looked like the two-mile hit would continue to be an impossible goal. But then, on his fifth and very last shot, Derek did it — he hit the 3368-yard target.
After Derek made the (nearly) two-mile shot, cheers erupted on the firing line — what an achievement! Derek is the first (and only) shooter to make the 3368-yard shot at K02M. Watch him do it in this video:
Derek Rodgers Hits Target at 3368 Yards on his Final Shot:
Derek Rodgers K02M-Winning Hardware and Ammunition
Factory Rifle Finishes in Second Place
With so many full-custom rifles on the firing line, many were surprised to see a factory rifle finishing second overall. Ronnie Wright shot superbly with his stock Barrett M99 chambered in .416 Barrett. Ronnie’s impressive second-place performance proved the effectiveness of the .416 Barrett cartridge (and the build quality of the M99). For ammo, Ronnie used Cutting Edge 472gr MTAC projectiles loaded in Barrett-stamped .416 cases. The powder was Alliant Reloder 50 ignited by CCI #35 50 BMG primers. The rifle had a Barrett factory 32″ barrel fitted with an Accuracy 1st level.
INTERVIEW with DEREK RODGERS:
Q: What do you believe contributed to your success at this match?
Derek: This match was truly a team effort from the entire Applied Ballistics Team. Emil Praslick and Paul Phillips are world class wind-readers and spotters. They have the ability to make decisive decisions and trust that I (as the shooter) will put a bullet on target every time a command is given. We posses a dynamic team background with a lot of history and experience under our belt. Our positive team synergy is hard to find. The addition of vital tools played a huge role in our success. A few of the tools we used were the AB Kestrel and Garmin Foretrex 701 AB Elite to give absolutely crucial and accurate ballistic solutions. The new McMillan ELR Beast stock was stable and the NF ATACR scope is robust and clear. The Bartlein barrel used was top notch! However, one of the most important pieces of the ELR puzzle and the only thing that separates the target is — the bullet. We chose Cutting Edge (CE) bullets due to their high level of precision. These bullets proved to be invaluable in connecting every piece of steel at the KO2M competition. The CE 400gr Lazer Max bullet was selected and was tremendously accurate. This bullet transitioned into a sub-sonic velocity without any loss of precision at ELR distances. Our success would not be possible if the projectile did not fly correctly for 7+ seconds of flight time. CE has outstanding designs and several quality choices to choose from.
Q: How many hours would you say you practiced for this match?
Derek: It is hard to calculate practice time in hours. ELR is a program that we work on every chance we get — day and night for months prior to the event. We have an extremely strong background of team shooting and long range shooting. A lot of time has been invested on and off the range, but does not stop there. The combined range time from other disciplines really helped me to be successful in transitioning from long range to ELR. It really is a compilation of 10 years of trials and tribulations. Some would say, “the Devil is in the details”. Our team tries very hard to not overlook any small detail. Practice and training is always scrutinized for improvements. Our Applied Ballistics team has a love and passion that goes beyond measurable amounts of time. We were fortunate to get together for two days a month prior to the Ko2M event to review our program and practice as a team. Bryan Litz had a plan, and we discovered as a team we had flaws in our program. Each one of us contributed from years of experience on improving our technique until we had a winning solution.
Q: Why did you choose the .375 CheyTac cartridge?
Derek: When I was asked to join the AB Team, I needed to get an ELR rifle built in a short period of time. I was under a very tight time schedule to get the project complete. In an effort to eliminate variables, I decided to keep things standard and as simple as possible. I chose the .375 CheyTac for the ease of getting components. The larger rifles are more difficult to get components quickly and I felt like the .375 CheyTac had enough attributes to be competitive at ELR distances.
The Cutting Edge 400gr bullets are milled from solid copper bar stock on a CNC Swiss-style lathe.
New ELR Hardware and Software on Display at K02M
This marks the second straight year that Team Applied Ballistics has won the K02M event. Last year, Team AB shooter Mitchell Fitzpatrick won the coveted “King of 2 Miles” title (Fitzpatrick finished fourth this year, just off the podium). In the past year, there has been considerable evolution in Extreme Long Range hardware and software, and projectiles are constantly being improved.
Bryan Litz (center) conferring with Team AB members Emil Praslick (L) and Doc Beech (R).
We asked Bryan Litz, founder of Applied Ballistics, to summarize developments in the ELR game. Here are Bryan’s observations:
“Each year the KO2M sees advancements and shooters converging on those tools and processes that have proven effective in prior years. It’s rather apparent, for example, that spotting impacts is a crucial part of success in this match. This was improved by the match directors/organizers placing the targets in very good locations for spotting impacts. We’re seeing less set-ups with adjustable bases, and more with solid/fixed scope mounts. One of the exciting new pieces of equipment is the periscope device made by TACOMHQ (John Baker). This device provides an optical shift to the image which allows you to get more elevation for those long shots. Also, the refinement of fire control (ballistic) solutions has really played a role in getting shooters centered up for their first shots.”
“This tournament highly favors first-round impacts with the scoring system, so the approach of ‘walking the shots on’, isn’t a winning strategy. Those who employed accurate ballistics solvers were able to score more first round hits, and pile up the points. First and second place (at least) were using Applied Ballistics solvers to center their shots. We’re looking forward to even more advancements and making these ELR shots even out to two miles more commonplace in the future thru systematically applying the Science of Accuracy.”
The winning Applied Ballistics Team:
Bonus Video — Interview with David Tubb at KO2M
Share the post "King of 2 Miles ELR Match — Derek Rodgers Takes the Crown"