On January 10, the National Shooting Sports Foundation (NSSF) and the Sporting Arms and Ammunition Manufacturers’ Institute (SAAMI) filed a lawsuit on behalf of their members against the State of California in Fresno Superior Court challenging the state’s microstamping law. NSSF and SAAMI seek to invalidate and enjoin enforcement of provisions of California state law enacted in 2007, but not made effective until May 2013. These newly “activated” provisions of California law will effectively require that ALL future models of semi-auto pistols be microstamp-capable. Note — semi-auto handguns that are currently on California’s “approved” handgun roster will not be banned from sale. But guns introduced in the future cannot be sold in California unless they have microstamping technology. If gun makers cannot include such features in their future designs, the next generation of handguns will effectively be banned from sale in California.
Under California law, firearms manufacturers would have to micro laser-engrave a gun’s make, model and serial number on two distinct parts of each gun, including the firing pin so that, in theory, this information would be imprinted on the cartridge casing when the pistol is fired. “There is no existing microstamping technology that will reliably, consistently and legibly imprint the required identifying information by a semiautomatic handgun on the ammunition it fires. The holder of the patent for this technology himself has written that there are problems with it and that further study is warranted before it is mandated. A National Academy of Science review, forensic firearms examiners and a University of California at Davis study reached the same conclusion and the technical experts in the firearms industry agree,” said Lawrence G. Keane, NSSF senior vice president and general counsel. “Manufacturers can not comply with a law the provisions of which are invalid, that cannot be enforced and that will not contribute to improving public safety. As a result, we are seeking both declaratory and injunctive relief against this back-door attempt to prevent the sale of new semiautomatic handguns to law-abiding citizens in California.”
In 2007, California Assembly Bill 1471 was passed and signed into law requiring microstamping on internal parts of new semiautomatic pistols. The legislation provided that this requirement would only became effective if the California Department of Justice certified that the microstamping technology is available to more than one manufacturer unencumbered by patent restrictions. On May 17, 2013, Attorney General Kamala D. Harris provided such certification. The DOJ’s certification notice has been attacked on the grounds that it is scientifically unsound, founded on little more than “wishful thinking”.
Share the post "NSSF and SAAMI Sue to Block California Microstamping Policies"
We dropped by the Stiller Precision Firearms SHOT Show booth to see the latest product roll-out from Jerry Stiller and his crew. Jerry showed off some of his hot new action designs, including the long-awaited Copperhead rimfire benchrest action. Along with two rimfire actions, Jerry unveiled his hot-selling P1000 Benchrest Action, and his new TAC30 AW bottom metal system for Rem-clone actions.
The advanced Copperhead rimfire BR action, “in development” for years, is finally a reality. This is a pure benchrest-quality action, built from the ground up to deliver the smallest groups with today’s rimfire ammo. The Copperhead’s innovative design features DUAL firing pins at 6 and 12 o-clock. This serves to make rimfire ignition as consistent as possible. This action also has an Anschutz-style feed ramp to aid feeding of single-shot rounds. Being very complex to manufacture, the Copperhead commands a fairly high pricetag — roughly $1300.00. For those in the highly competitive rimfire benchrest game, who demand the very best rimfire receiver available, the high price is can be justified by the action’s superior performance. Prototypes have already earned top places ijn many notable rimfire BR matches.
Along with the Copperhead, Stiller Precision offers a nicely-detailed, smooth-running 40x clone rimfire action that will fit any stocks inletted for the Remington 40 Rimfire rifles. This 40X Rem clone action is in stock and available know for about $950.00.
Yet another unique action from Stiller Precision is the Tac-30 AW. This is a Rem-footprint action made as a purpose-built tactical rifle foundation. It has beefy #8 screws for scope base attachment along with the ability to add rail pins to a picatinny rail to reduce the possibly of any screw failures. Along with that, it is specifically made to work in concert with Stiller’s detachable magazine bottom metal and Accuracy International AW magazines. The entire action, bottom metal and magazine combination is available for about $1,100.00. The AW magazine is superior to the standard AICS mag; the AW design is easier to load, and it holds ten rounds in a more compact (shorter) box.
Last but not least, Stiller showed us a P1000 action which is becoming more popular in the long range benchrest realm and is available in standard and magnum bolt faces for short and long action calibers. This dual-port action is only available in a right-bolt, left-port, right eject configuration. It is also available in 2 diameters – 1.350” and 1.550” in case weight is an issue. Interestingly, the P1000 is made to work without the standard recoil lug as you can see it has recesses cut in the bottom that will act as a recoil lug surface. Similar to other Stiller’s actions, the P1000 has a small size (0.068″ diameter) firing pin for enchanced accuracy.
Stiller Precision is working hard to catch up on existing orders as well as continuing to develop innovative, state-of-the-art actions for discerning customers. Most of the actions on display at SHOT show are in stock and ready to ship. In addition, Stiller hopes to resume production of his popular Viper and Diamondback actions in just a few months. Jerry cautions “be patient” if you are looking for a drop-port or other classic benchrest not currently in inventory.
Share the post "SHOT Show Report: New Actions from Stiller Precision"
The following recall and safety notice was issued on September 20, 2011 by Steyr Arms. Apparently some Steyr 9mm pistols have an issue which could allow the firearm to discharge without a normal trigger pull. The affected serial numbers are listed below.
Steyr Arms, Inc. has determined a potential condition with the firing pins in a very limited number of 9mm Steyr M9-A1, C9-A1 and S9-A1 pistols that could possibly allow the pistol to fire without the trigger being pulled. Although Steyr Arms, Inc. has not received any reports of accidents or injuries, it is voluntarily initiating this recall to protect the safety of its customers because of the remote possibility of an unintentional discharge occurring.
The affected M9-A1 pistols bear serial numbers 3021926-3021928, 3021932-3021935, 3021946-3021955, 3021966-3021988, 3021990-3021993, 3021995-3022001, 3022003-3022005, 3024663-3024672, 3024683-3024688, 3024690-3024702, 3024704-4024712, 3024733-3024738, 3024741-3024742, 3024802-3024811, 3024852-3024871, 3024882-3024901, 3025299-3025308, 3025311, 3025313-3025333, 3025335-3025338, and 3025353-3025359.
The affected C9-A1 pistols bear serial numbers 3022128-3022145, 3022152, 3022169-3022171, 3022174, 3022176-3022178, 3022180-3022201, 3022203-3022218, and 3022845-3022854.
The affected S9-A1 pistols bear serial numbers 3022929-3022931, 3022933, 3022935-3022937, 3022975-3022977, 3022988-3022991, 3022993, 3022995-3022996, 3024146-3024175 and 3024354.
Only the M9-A1, C9-A1 and S9-A1 pistols with the serial numbers identified above are affected by this recall. If your pistol has a different serial number, it is not subject to the recall.
How to Respond to Recall
If you own a Steyr M9-A1, C9-A1 or S9-A1 pistol with a serial number identified as being affected by this recall, please do not load or fire your Steyr M9-A1, C9-A1 or S9-A1 pistol and contact us immediately to arrange to have the firing pin in your pistol replaced, free of charge, using the following steps:
Step 1 – Contact us at 205-655-8299 (Monday-Friday 8-5 Central Standard Time) or at www.steyrarms.com/contact and provide the model and serial number of your pistol.
Step 2 – After confirming that your pistol is subject to this recall, we will send you a prepaid overnight shipping box with instructions so that you can return your pistol to us, free of charge.
Step 3 – We will replace the firing pin in your pistol and return it to you overnight free of charge. We will make every effort to return your pistol to you within one week of receiving it.
Share the post "Steyr Arms Recalls 9mm M9-A1, C9-A1, AND S9-A1 Pistols"
Shooters who convert factory actions to run 6BRs, 6PPCs or other high-pressure cartridges should consider having the firing pin bushed. These modern cartridges like to run at high pressures. When running stout loads, you can get cratering caused by primer flow around the firing pin hole in the bolt face. The reason is a little complicated, but basically the larger the hole, the less hydraulic pressure is required to crater the primer. A limited amount of cratering is normally not a big issue, but you can reduce the problem significantly by having a smith fit a bushing in the firing pin hole. In addition to reduced cratering, bushing the firing pin often produces more consistent ignition.
This is a highly recommended procedure that our editors have had done to their own rifles. Greg Tannel (Gre-Tan Rifles) is an expert at this procedure, and his turnaround time is fast — usually 2-3 days (shop time). Current price for a bushing job, which includes turning the firing pin to .062″, is $82.00 including USPS Priority Mail return shipping.
If you have a factory rifle, a bushed firing pin is the way to go if you are shooting the high-pressure cartridges such as 6PPC, 6BR, 6-6.5×47 and 6.5×47. This is one of the most cost-effective and beneficial upgrades you can do to your factory rifle. For more info on the Firing Pin Bushing process, visit GreTanRifles.com, or email greg [at] gretanrifles.com. (After clicking the link for GreTanRifles.com, Click on “Services” > “Shop Services” > “Bolt Work”, and you’ll see a listing for “Bush Firing Pin Hole & Turn Pin”. Select “View Details”.)
Firing Pin Hole Bushing by Greg Tannel
Work Done: Bush firing pin hole and turn pin.
Functions: Fixes your cratering and piercing problems.
Price: $75.00 + $7.00 return shipping Total Price: $82.00
Actions for which Bushing is Offered: Remington, Winchester, Savage, Sako, Kimber, Cooper, Nesika, Stiller, Bat, Kelbly, Lawton, Surgeon, Borden, Wichita, Hall, CZ, Ruger, Mauser, Howa, Weatherby, Dakota, Pacific Tool, Phoenix, RPA Quadlite, and Defiant bolt action rifle or pistol. Note: There may be extra tooling charges for case-hardened style bolts (Mauser, CZ, and similar) .
Actions for which Bushing is NOT Available: ARs, Accuracy International, Desert Tactical Arms, Big Horn, Rim fires, Falling block, Break open, Lever, Pump rifles.
How to send your bolt in to be bushed:
You can send your bolt snail mail, priority mail, UPS, Fed-Ex. What ever you prefer. Please include your name, phone number, and return shipping address. Turn around is normally 1 to 3 days shop time (plus shipping time). We usually do them the day that we get them in. Total cost is $82.00 for one bolt or $157.00 for two (this includes return shipping, priority mail.) Three or more will be sent back to you UPS and we will have to calculate extra shipping. We can overnight them at your expense. Check, money order, or credit card is fine with us.
Share the post "Tannel Firing Pin Bushing Cures Primer Cratering"
On January 10, the National Shooting Sports Foundation (NSSF) and the Sporting Arms and Ammunition Manufacturers’ Institute (SAAMI) filed a lawsuit on behalf of their members against the State of California in Fresno Superior Court challenging the state’s microstamping law. NSSF and SAAMI seek to invalidate and enjoin enforcement of provisions of California state law enacted in 2007, but not made effective until May 2013. These newly “activated” provisions of California law will effectively require that ALL future models of semi-auto pistols be microstamp-capable. Note — semi-auto handguns that are currently on California’s “approved” handgun roster will not be banned from sale. But guns introduced in the future cannot be sold in California unless they have microstamping technology. If gun makers cannot include such features in their future designs, the next generation of handguns will effectively be banned from sale in California.
STEYR ARMS — SAFETY WARNING + RECALL NOTICE
Firing Pin Hole Bushing by Greg Tannel
