Summer’s here, so many folks will head to the hinterlands on prairie dog safaris. On a good P-Dog adventure, you may shoot hundreds of rounds over a long weekend. So you’ll need plenty of ammo. With these ammo volume requirements, you probably won’t have time to load to benchrest standards, and you may not have the budget for match-grade bullets. To save time you may throw (rather than weigh) your charges, or even load on a progressive press. This all raises the question of ammo accuracy — how good is “good enough”? A Sierra Bullets expert answers that question here — explaining how to efficiently load ammo for varmint work.
Ammunition Accuracy Requirements 101 — Varmint Ammo
This story based on article by Sierra Bullets Chief Ballistician Tommy Todd
I load and shoot ammunition for a living. In my duties here at Sierra I constantly test bullet accuracy for our production needs. Because of this, I shoot a variety of different calibers and cartridges on a daily basis and a large demand of this shooting is keeping the guns and loads tuned for optimum accuracy. I have a very narrow window of tolerances to maintain in order to provide our customers (you) with the most accurate bullets on the market.
I have learned many tricks and techniques over the years to tuning a load, prepping brass, and cleaning barrels to keep a gun shooting. I often utilize the things I have learned and take them to extreme levels when competing in a shooting event. I also often ignore most of these things (other than safety) and simplify the process if the shooting I will be doing does not warrant.
Recently I went on a prairie dog shoot in Wyoming with some good friends. The targets cooperated as did the weather with the exception of some challenging winds we experienced. We had a great time and make a lot of hits on those small rodents. When loading for the 223 Remington rifles and the TC Contender, I cut a few corners in the ammunition-loading process due to both time constraints and accuracy needed. When shooting at a prairie dog a miss is simply that, but when shooting at say the X-ring at 1000-yard competition, a poorly-placed shot [harms your] placing in the match. Because of this, I can afford to miss an occasional shot at a varmint due to ammunition capability without worry but will not allow the same tolerances in my match ammo. For the Wyoming trip I utilized a powder measure and simply dumped the charges into primed cases that had been full-length sized and primed.
I had measured enough for length to know that while there was some variance all were under maximum length. I know there is some variation of the measure I utilized but not significant enough to warrant weighing every charge. When seating the bullets a competition seating die was used and I verified OAL on the occasional cartridge to make sure nothing changed.
The ammo produced shot under one inch at 200 yards in one of the guns I planned on taking on to Wyoming with me. [Editor: That was for TEN Shots — see below.] I knew I had loaded ammunition that was quite suitable for the task at hand which was evidenced by the number of hits I was able to make at fairly long range.
NOTE: The author, Tommy Todd, explains that, when loading ammo for F-Class matches, he uses more exacting methods. He weighs every charge and seats his bullets carefully with an arbor press. Todd adapts his methodology for his particular application. The lesson here is to load to the level of precision demanded by your discipline. READ Full Story HERE.
Sinclair International has created a series of helpful articles on rifle cartridge reloading. Today’s feature lists ten basic steps for precision hand-loading, with links to longer, detailed Sinclair Int’l technical articles providing more complete information. There’s a lot of helpful info here guys, if you click all the links to access the ten “long form” articles.
Tying It All Together: 10 Steps To Precision Handloads
Feature based on article by Roy Hill, Brownells/Sinclair Copywriter
Sinclair International offers a series of detailed articles on hand-loading precision rifle ammunition. The articles are included in Sinclair’s GunTech Articles Archive, but sorting through the index to find each article takes time. To help you access all these articles quickly, here’s a handy summary of ten key topics, with links to longer articles covering each subject in detail.
Part 1: The first step in making high-quality handloads is to carefully choose the best brass for your application. You need to know how to identify the different types of brass and how to choose the best kind for the ammo you want to load. CLICK HERE for Part 1.
Part 2: Even high-quality brass can have burrs around the flash hole that can interfere with the primer flame and cause inconsistent ignition – which can lead to shot groups opening up. Flash hole deburring is a critical step in making sure primers ignite powder consistently. CLICK HERE for Part 2.
Part 3: The next step is to make sure the primer pockets are square and uniform. Like flash hole deburring, primer pocket uniforming may reduce variations in primer ignition by ensuring more consistent primer seating. CLICK HERE for Part 3.
Part 4: Making sure all your cases are precisely the same length is crucial, especially when you use cases that have been fired before. Case trimming is the way to get there. CLICK HERE for Part 4.
Part 5: After trimming, cases still have to be resized. In order for them to work through the resizing die, they have to be lubricated. The case lube method you choose is crucial to making precision handloads. CLICK HERE for Part 5.
Part 6: Now it’s time to choose the dies that will resize your cases. There are several important options to consider in selecting the right sizing dies. CLICK HERE for Part 6.
Part 7: Wait! You’re not quite ready to start sizing yet. There’s yet more to consider before you start cranking cases through the press. Learn more about setting up and adjusting your sizing dies. CLICK HERE for Part 7.
Part 8: Once the cases are completely prepped, it’s time to start putting fresh components back into them. We start off by seating primers. CLICK HERE for Part 8.
Part 9: After the primers are seated, it’s time to drop in the powder. There are several tools that will help you handle powder for precision handloads. CLICK HERE for Part 9.
Part 10: The final step in the process is carefully seating the bullet to just the right depth. And then… you’re ready to try your loads at the range. CLICK HERE for Part 10.
A while back, we featured a portable reloading bench built on a Black & Decker Workmate. That proved a VERY popular do-it-yourself project so we’re showing it again, in case you missed it the first time.
Texan Robert Lewis made himself a great portable reloading bench from plywood mounted to a Black & Decker Workmate. The bench, roughly 22″ x 19″ on top, folds up to fit easily in your car’s trunk or behind the seats in a pick-up truck cab. Four recessed bolts hold the wood top section to the collapsible B&D Workmate.The sides and back of the unit are attached to the base with small nails. There is a small shelf (also nailed in place) which can be used to clamp a powder measure or hold a scale. Shown in the photo is a Harrell’s Benchrest measure and Harrell’s single-stage “C” press.
The whole unit can be built for about $65.00 with pine, or $80.00 with oak (as shown). Robert explained: “The Workmate was $40. If someone bought a 2’x4′ sheet of 3/4″ oak plywood, I think it is around $30. Using pine plywood would be about half that. Fasteners were $3. Spar Urethane would be $5.”
Robert told us: “I used a couple ideas I found on the web. The Larry Willis website gave me the idea to use the Black and Decker Workmate as a base. I found the Workmate on sale for $40 and the top is made from oak plywood I had in my shop. I sealed the wood with three coats of Spar Urethane. The whole thing folds into a nice package for transportation to and from the range.”
Editor’s NOTE: In the time that’s transpired since we first ran this story, the price of a Black & Decker Workmate has gone up. However you can still pick a WM225 Workmate for under $60.00. Amazon is currently selling WM225 Workmates for $59.58. The next best price we found was $69.61 at Home Depot, still a good price (Lowe’s is charging $94.98).
Here’s something you don’t see every day — a reloading press that has loaded over 1,000,000 rounds of ammo. At the NRA Convention in Dallas, Redding showcased an old Redding T-7 Turret Press delivered to Sierra Bullets decades ago. 0ne of the very first T-7s made by Redding, this “old warrior” was used by Sierra Bullets to load over 1,000,000 rounds of ammunition in Sierra’s ballistics lab.
Redding T-7 Still Within Spec
After all that loading, Redding tested the press and, remarkably, found that it still remained “within spec”. Redding notes: “This press was subjected to real world reloading wear and stress yet remains within ‘new’ spec after this historic test”. At the Dallas NRA event, this press was fitted with indicators to show “just how good American Steel and craftsmanship remains after what, in a normal situation, would represent numerous lifetimes of use.”
Redding Reloading Equipment has crafted quality, American-Made products for the precision handloading market since 1946. To learn more about Redding products or to request a copy of the 2018 Redding catalog visit Redding-Reloading.com.
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Whittaker Guns — Howa Mini Action .223 Rem, $349.99
This is hard for a varmint hunter to resist. You can get a complete Howa .223 Rem rifle for $349.99 — about the price of a replacement barrel blank for a Remington. This little gem has a smooth, short-throw Mini Action with Howa’s excellent two-stage trigger. The .223 Rem is a fine choice for prairie dog work, with good barrel life and great factory ammo options. Yes we’d prefer a heavier barrel for extended shooting sessions, but this is still a great price on a fine little rifle. NOTE: This month get 10% Off other items at Whittaker Guns (site-wide) with code MAYDAY.
2. Midsouth — Hornady Auto Charge Dispenser, $158.99
Here’s a great deal from our friends at Midsouth. Hornady’s versatile Lock-N-Load Auto Charge™ Powder Scale and Dispenser is on sale for $158.99 at Midsouth. The Hornady Auto Charge is accurate to 0.1 grains of powder and can hold up to 1000 grains of powder in its hopper. This is a very good value compared to other electronic powder scale/dispensers on the market, such as the RCBS ChargeMaster Lite, currently $257.24 at Amazon (nearly $100 more).
The brand new Ruger Precision Rimfire could become one of 2018’s most popular rifles, if the success of its “big brother”, the centerfire Ruger Precision Rifle, is any indicator. This .22 LR rig offers a turn-key rimfire solution for tactical shooters, PRS competitors, and anyone who likes modular rifles. The Ruger Precision Rimfire rifle offers adjustable cheekpiece and length of pull, AR-style grip, free-floating M-Lok fore-end, and a 18″ barrel (1:16″ twist) pre-threaded for brakes or suppressor. Sportsman’s Guide sells this rimfire rig for $399.99 (or $379.99 member price).
4. Black Rifle Deport — Aero Precision Upper Receiver, $69.95
Looking to build a black rifle? Check out this Aero Precision Assembled Upper Receiver. Right now this upper receiver assembly is discounted to $69.95 plus you get a free charging handle ($12.95 value). This is a good component for a project (you must add the barrel, bolt, bolt carrier, stock etc. of your choice). NOTE, this upper includes port door, charging handle, and forward assist but does NOT include bolt or bolt carrier assembly. And this is NOT, repeat NOT, a complete upper — no barrel, handguards, gas system or sights. Got that?
5. Amazon — Plano 52″ Double Rifle Case with Wheels, $109.08
This Plano Double Scoped Rifle Case is an Amazon Best Seller for good reason. It offers the functionality and durability of an SKB-type hard case for HALF the money. This is under $110.00, while the equivalent SKB is around $240.00, so you can buy two Planos for the price of one SKB. The 51.5″ interior will fit most scoped competition rifles up to about 29″ barrels (measure your own rifle to make sure). If you separate the barreled action from the stock you can transport even ultra-long ELR rifles. The handles are convenient and beefy and the wheels make this case easy to move. This is a very tough, roomy case for the money (plus there’s Free Shipping).
Exterior Dimensions: 54.625″ x 15.5″ x 6″
Interior Dimensions: 51.5″ x 12.63″ x 5.25″
Pluckable Interior Dimensions: 46″ x 10″
Features: Wheels, Secure Draw-Down Latches, O-Ring Seal, Pressure Relief Valve, Customizable Foam
6. Amazon — Howard Leight Impact Sport Electronic Muffs, $34.99
Just in time for Mother’s Day, Amazon has PINK Howard Leight electronic muffs on sale for just $34.99. These Impact Sport muffs are popular among shooters as they are reliable, reasonably comfortable, and easy to store. Built-in directional microphones amplify range commands and other ambient sounds to 82 dB, providing more natural listening and enhanced communication. These muffs carry a 22 NRR Noise Reduction Rating (NRR). The bottom of the muffs is thinner for clearance on a rifle stock, and the headband is adjustable. These Impact Sport Earmuffs include AUX input and 3.5 mm connection cord for MP3 players and smartphones.
7. Stocky’s — LR Stocks with Aluminum Bedding Block, $179.99
Here’s a good deal on a versatile Stocky’s Long Range Stock with aluminum V-block bedding system. For just $179.99, order this for Rem/Rem Clone long actions or short actions, with either narrow or wide (varmint/tactical) barrel channel. This would be a good choice for a varmint rifle. This is also offered with handsome hydrographic or web-pattern baked-on textured finishes for $199.99.
8. Sportsman’s Guide — 1400 Rimfire Rounds $71.49
Need rimfire plinking ammo? Here’s a super bargain. With Remington’s Bucket 0′ Bullets, you can get 1400 rounds of .22 LR ammo for $71.49 ($67.92 member price). That works out to just $0.051 per round. A nickle a round is plenty affordable. You can shoot 200 rounds for just ten bucks — about what a movie ticket costs these days.
9. FosPower 10200 mAh Waterproof Charger, $25.99
When you’re at the range or on a hunt, it’s smart to have a USB-output battery pack for smart phone, target-cam monitor, even a LabRadar. There are many battery packs available, but most are fairly fragile, with exposed ports. This “ruggedized” FosPower 10200 mAh charger is different. It is waterproof, dust-proof, and shock-proof. (IP67 certified: dust and water resistance for up to 3ft/1m for 30 minutes under water.) It can handle all that a PRS competitor or hunter can dish out. It even has a handy LED light. Right now it’s priced at $25.99 with FREE Shipping (on orders over $25.00).
If you have an older version of QuickLOAD, such as V3.1 shown above, then you should definitely upgrade. This will give you more complete and up-to-date cartridge, powder, and bullet data files.
Got QuickLOAD software? Then it’s time to upgrade your data files — new data became available in January 2018. The makers of QuickLOAD offer inexpensive CDs with updated data files (for propellants and projectiles). These data update CDs will add the latest available powder, cartridge, and bullet files to your current version of QuickLOAD/QuickTARGET.
There are two update CDs now offered with data current through January 2018. One handles the older installations, QuickLOAD/QuickTARGET 3.0, 3.1, 3.2, 3.3, 3.4, and 3.5. A second update CD works for QuickLOAD/QuickTARGET 3.6, 3.8, and early 3.9. This second disk is primarily a data update.
Price for either update disk is $15.95. In North America, order from Neconos.com, or call 800-451-3550 (9 am to 5 pm Pacific Time). In the United Kingdom, you can get the update disk from JMS Arms, Merrivale, London Road, Handcross, West Sussex, RH17 6BA, England, Phone: 01444 400126. In Europe you can order direct from QuickLOAD’s creator: Ing. Hartmut Broemel, Neubrecker Weg 15, D-64832 Babenhausen, Germany, fax/phone (+49) 0 6073 688481
QuickLOAD is a pretty amazing program. Using information for over 1200 cartridges, 250 powders, and 2500 bullet types, QuickLOAD allows you to predict velocities and pressures for your hand-loaded ammo. You can check predicted pressures with different powder choices and seating depths before loading an actual round. If you do not yet own QuickLOAD, you can now order the latest Version 3.9 of this unique software. Priced at $152.95, the latest version 3.9 contains all the updates through January, 2018 and is compatible with WINDOWS 2000, XP, VISTA, Windows 7, Winows 8 and Windows 10. QuickLOAD/QuickTARGET 3.9 can be purchased for $152.95 from Neconos.com. For a full explanation of the features and benefits of QuickLOAD software, click the link below.
EDITOR’S Comment: We believe every serious rifle hand-loader should own and use QuickLOAD. We have used this program for over a decade. It is invaluable in load development, particularly when testing a variety of bullets and when changing seating depths. This software is NOT a substitute for standard, conservative reloading practices. However QuickLOAD can very surprisingly effective in comparing cartridge performance and predicting the effects of changes in charge weight.
Product tip from EdLongrange. We welcome reader submissions.
Before you load that nice new cartridge brass for the first time, run an expander mandrel down the case necks. This will iron out dents and provide more uniform neck tension. Chose a mandrel diameter that provides appropriate neck tension.
Lapua brass is so good that you’ll be tempted to just load and shoot, if you have a “no-turn” chamber. However, some minimal case prep will ensure more uniform neck tension. Keeping your neck tension very uniform allows more consistent bullet seating. That, in turn, usually yields better accuracy, and lower Extreme Spread and Standard Deviation (ES/SD). Lapua brass, particularly 6mmBR, 6.5×47, 6.5 Creedmoor, and .308 Win comes from the factory with tighter-than-optimal necks. Before you seat bullets, at a minimum, you should inside chamfer the case mouths, after running an expander mandrel down the necks. The expander mandrels from both Sinclair Int’l and K&M will both leave the necks with enough neck tension (more than .001″) so you can then seat bullets without another operation. We suggest putting a bit of lube on the mandrel before running it down the necks — but remove any lube that gets inside the necks before seating bullets.
Both Sinclair and K&M Tools make a die body specifically to hold expander mandrels. The Sinclair version, is shown above. This $28.99 unit fits caliber-specific expander mandrels ($9.99) which measure approximately .001″ less than bullet diameter for each caliber. This is an updated “Gen II” design that completely captures the mandrel within the die so the mandrel cannot pull out. It also has an O-ring in the die cap that allows the mandrel to self-center within the case neck. Sinclair now offers three sizes of die bodies for expander mandrels: .17 -.338 Caliber (#749-011-715WS); .357 – .50 caliber (#749-008-843WS), and a special .50 Cal die body for large-diameter 50 BMG presses (#749-009-163WS, $39.99). All Generation II dies are machined from stainless steel and the standard diameter 7/8-14 dies include the Sinclair Stainless Steel Split Lock Ring.
Once you run the Sinclair expander mandrel down the necks of Lapua brass, after you account for brass spring-back, you’ll have about .002″ neck tension*. This will make the process of seating bullets go much more smoothly, and you will also iron out any dents in the case mouths. Once the case mouths are all expanded, and uniformly round, then do your inside neck chamfering/deburring. The same expander mandrels can be used to “neck-up” smaller diameter brass, or prepare brass for neck-turning.
Forum member Mike Crawford adds: “These expanders can also reduce runout from offset seating. Prior to bullet seating, expand the sized necks to force thickness variance outward. With the Sinclair system, the necks will springback fine, and will not be pulled out of center. This leaves plenty of tension, and bullets seated more centered. I do this, even with turned necks, to get improved seating.”
Mandrels vs. Expander Balls on Decapping Rods
If you haven’t acquired an appropriate expander mandrel for your brass, but you DO have a full-length sizing die with an expander ball, this will also function to “iron out” the necks and reduce tension. However, using a die with an expander ball will work the necks more — since you first size them down, then the ball expands them up again. Typically (but not always), run-out is worse when using an expander ball vs. an expander mandrel.
* This .002″ tension is what we have observed with Lapua 6mmBR, 6.5×47, 6.5 Creedmoor, and .308 Win brass. This might vary with much smaller or larger cases, and of course a different brand of brass might yield different results. If you get too little tension with your current mandrel, you can get a smaller-diameter mandrel from 21st Century Shooting. 21st Century even offers low-friction Titanium Nitride-coated mandrels.
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Natchez — Bushnell Scopes, Deep Discounts Plus 30% Rebate
Natchez Shooters Supply is running a big sale on Bushnell riflescopes right now. You can save $60 to $110 off the normal prices. Plus, through the end of March, Bushnell will rebate an additional 30% of the item’s purchase price (in the form of a prepaid credit card). Shown above are four great Bushnell scope deals, but there are many more. Plus the 30% rebate also applies to Bushnell binoculars and Laser Rangefinders, in addition to riflescopes.
2. Brownells — Howa 1500 Barreled Actions, Starting at $279.99
Howa makes excellent, smooth-running actions, and the Howa HACT 2-stage trigger is WAY better than most domestic factory triggers. Right now you can save big bucks on Howa 1500 barreled actions, complete with HACT trigger and trigger-guard, starting at $279.99. Both regular actions and Mini Actions are offered. Available chamberings include 6.5 Grendel, 6.5 Creedmoor (back-ordered), 7.62×39, .308 Winchester, and .300 Win Mag. Some of these barreled actions come with a rugged Cerakote finish, while others have a blued finish. You can also get FREE Shipping with Code MDV during checkout. But note, this item requires delivery to an FFL-holder.
3. Grafs.com — Rock Chucker Supreme Reloading Kit, $226.99
Everything you see above can be yours for just $226.99, after RCBS $100.00 Rebate. Hell of a Deal. Right now, Grafs.com is selling the Rock Chucker Supreme Master Reloading Kit for $326.99. But check it out — this Master Reloading Kit now qualifies for a $100.00 RCBS Rebate (“Buy Green, Get Green”). That lowers your net cost to just $226.99. That an amazing deal considering all the hardware you get: Press, Primer Tool, Scale, Powder Measure, Loading Tray, Reloading Manual and more. Heck, the Rock Chucker press alone is worth $160.00+. NOTE: To qualify for the $100 Rebate you must purchase on or before March 31, 2018. The $100 Rebate is for products costing $299.99 to $499.98.
4. Amazon — NRR 31 Muffs and Eyewear Kit with Case, $29.99
Here is a great combo package that offers complete eye and ear protection for shooters at the range. The Ear Muffs feature a 6-piece noise filtration system that effectively blocks low, mid, & high range frequencies, giving them an impressive NRR 31 noise reduction rating. The muffs ship with a nice zippered case that also holds the supplied safety eyewear. This kit also comes with ten (10) NRR 33 foam earplugs. You can order the kit with either clear eyewear or smoke-tinted lenses.
This Norma Match-22 ammunition is good stuff. In many rifles it shoots as well as $8/box products from other makers. But now you can get Match-22 for the equivalent of $4.00 per 50-round box. MidwayUSA is selling 1500 rounds (three 500-round cases) plus an ammo can for just $124.99 with FREE Shipping. That works out to just 8.3 cents per round. If you can’t use that much you can also get 500 rounds for $39.99 (i.e. $4/box), also with FREE shipping. We think you’ll be happy with this ammo. It is a good choice for tactical cross-training, rimfire silhouette, and fun shooting.
6. Grafs.com — Lapua 6.5 Creedmoor SR Primer Brass, $99.99/100
Here’s an excellent value from our friends at Grafs.com. Lapua 6.5 Creedmoor cartridge brass with Small Rifle Primer and Small Flash-hole is on sale for $99.99 per 100 cases. This is quite simply the best 6.5 Creedmoor brass in the world. It will hold higher pressures, deliver more velocity, and hold up to more reloading cycles. Chances are you will also see more accuracy with this Lapua brass than with other brands. If you shoot a 6.5 Creedmoor, you may want to grab some now. Other vendors are charging a lot more. For example, this very same Lapua brass is $124.99 at MidwayUSA right now.
7. Amazon — Jialitte Scope Bubble Level, $12.49
CHANGE ART NUMBER
All serious rifle shooters need a scope level. This nicely designed Jialitte Scope Bubble Level features a 30mm milled inside diameter, plus an inner insert ring so it will also fit 1″-diameter main tubes — that dual-diameter versatility is a nice feature. We also like the way the unit is nicely radiused, and has a low profile in the middle. Price is just $12.59 with free shipping. User reviews have been very positive. You could easily pay $35.00 or more for a 30mm scope level. Purchasers have praised this product — nearly all verified buyers rated this five stars.
8. Amazon — Neiko Digital Calipers, $17.85
Even if you have a good set of calipers, you may want to get one of these Neiko 01407A Digital Calipers. The #1 best-selling digital caliper on Amazon.com, this Neiko tool features a large LCD Screen and measures up to 6.0 inches. With over 3000 customer reviews, this product has earned an overall rating of 4.4 out of 5 stars. It’s hard to go wrong for $17.85, even if you just use these as a spare set for measuring group sizes and case trim lengths.
9. Amazon — Two Rolls of 3″ Neon Target Stickers, $14.95
We like these bright, Neon 3″ target stickers. They are big enough to see easily at 600 yards, giving you a 1/2 MOA target center at that distance. For $14.95 at Amazon.com, you get 250 3″-diameter self-adhesive centers (125 targets per roll) that stick to almost any surface The high-contrast fluorescent red/orange color provides an excellent HI-VIZ aiming point, along with good contrast for bullet holes that fall within the 3″ circle. To help line up your reticle cross-hairs, the target centers feature black markers at 3, 6, 9, and 12 0’Clock. NOTE: These stickers may qualify for FREE Shipping with combined orders over $25.00.
Sinclair International has created a series of instructional videos illustrating the basics of metallic cartridge reloading. The 8-part series starts with reloading basics and provides step-by-step, how-to instructions that will help new reloaders get started. Detailed, animated illustrations show you what happens inside the chamber when shooting, and inside the dies during each step of reloading. The videos can be viewed on Sinclair Int’l’s YouTube page. Shown below is the first video in the series:
Each of the eight videos is hosted by Sinclair Int’l President Bill Gravatt. Bill doesn’t just show you “how”, he tells you “why”. The how-to segments cover case inspection, proper die set up, case sizing, primer installation, powder measuring, bullet seating, crimping, and even goes into the record keeping needed for the handloader. “We wanted to give shooters who haven’t reloaded a look at all the advantages of creating your own ammo and how easy it is to get started,” said Gravatt, “without telling them they had to have any certain brand or type of equipment to do the job.” The eight videos are:
Part 1 — Intro to Video Series
Part 2 — Intro to Reloading Safety
Part 3 — Metallic Cartridge Components
Part 4 — The Firing Sequence
Part 5 — Tools for Reloading
Part 6 — Loading Bottle-Neck Cartridges
Part 7 — Loading Straight Wall Cartridges
Part 8 — Reloading Series Conclusion
Reloading Tools
Shown below is Part 5 of the video series, covering the tools used for precision reloading.
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
Ruger Precision Rifle, 6.5 Creedmoor, $983.00 complete — what’s not to like? If you’ve been thinking of purchasing a Ruger Precision Rifle (RPR) chambered for the 6.5 Creedmoor cartridge, here’s the best deal we’ve found in recent months. Right now Gunprime.com is offering this poular tactical rig for under $1000.00, in the high-demand 6.5 Creedmoor chambering. Heck of a bargain boys — you can pay $1300 or more elsewhere for the same rifle. This is a good choice for the PRS production class, or you can take in to another level of performance with a Pre-Fit 26″ cut-rifled barrel from Krieger. This is the lastest RPR Gen 2 version with the upgraded handguards.
NOTE: CDNN also has the RPR Gen 2 in 6mm Creedmoor for $899.99. That price, which includes rings, is the lowest we’ve ever seen for a Gen 2 model.
You don’t need to spend big bucks for an effective spotting scope to view mirage. You can get the Kowa TSN-501 Angled Spotting Scope is listed at $349.00 from B&H Photo. But, you can actually buy this Spotter for $299.00 — B&H just can’t advertise it that low. They list $349.00 but you get another $50 discount when you put it in the shopping cart: SEE REAL PRICE HERE. That’s a heck of a deal. This is a super-compact scope with 50mm objective and built-in 20-40X eyepiece. Though relatively new, the small, light-weight TSN-501 can perform basic spotting tasks effectively. This doesn’t have the resolution of the $1500+ spotters but this is fine for viewing mirage and shot markers. Put the money you save into barrels and bullets.
3. CDNN — Winchester XPR Hunting Rifle, $264.99 After Rebate
We like the Winchester XPR as an affordable, entry-level hunting rifle. The three-lug bolt has a short throw, the mags seat easily and a wide range of chamberings are available. Right now CDNN is offering the XPR for just $339.99. That’s a great price, but it gets even better. Winchester is offering a $75.00 factory rebate, lowering your net cost to just $264.99. That’s less than you’ll pay for a new custom barrel! The $75 Rebate applies to any NEW Winchester XPR rifle purchased from February 1 through March 31, 2018. For more info, visit rebates.winchesterguns.com.
4. Amazon — Howard Leight Electronic Muffs, $35.99
Every shooter should own a pair of Electronic muffs, even if you prefer shooting with earplugs and/or standard muffs. Electronic muffs are great when you are doing spotting duties or are working near the firing line. They allow you to hear ordinary conversations while still providing vital hearing protection. Right now Amazon.com has the Howard Leight Impact Sport Electronic Muffs on sale for just $35.99, with free Prime Shipping. This is good deal — these NRR 22 muffs are currently Amazon’s #1 seller in the category.
5. Hornady — Advanced 4DOF Mobile Ballistic App, FREE
Hornady offers a FREE Ballistic Calculator App for iOS (Apple) and Android OS. This new Mobile Ballistic App includes Hornady’s advanced 4DOF™ calculator as well as a standard BC (ballistic coefficient) calculator. The Hornady Ballistic Calculator App is Bluetooth-enabled so it can communicate with select wind meters.
The Hornady Ballistic App is FREE but you do need to supply an email address. We found the App downloaded quickly and installed easily. While the Mobile Ballistic App is new, Hornady has offered a web-based online 4DOF Ballistic App since August 2016.
6. Amazon — Jiallite Scope Bubble Level, $11.99
If you shoot long range, you need a scope level. This nicely designed Jiallite Scope Bubble Level is fully CNC-machined to close tolerances for a good fit. It features a 30mm milled inside diameter, plus an inner insert ring so it will also fit 1″-diameter main tubes — that dual-diameter versatility is a nice feature. We also like the way the unit is nicely radiused, and has a low profile in the middle. User reviews have been very positive. You could easily pay $35.00 or more for a 30mm scope level. Purchasers have praised this product — almost all verified buyers have rated this five stars.
7. Amazon — Neiko Digital Calipers, $16.85
Even if you have a good set of calipers, you may want to get one of these Neiko 01407A Digital Calipers. The #1 best-selling digital caliper on Amazon.com, this Neiko tool features a large LCD Screen and measures up to 6.0 inches. With over 3000 customer reviews, this product has earned an overall rating of 4.4 out of 5 stars. It’s hard to go wrong for $16.85, even if you just use these as a spare set for measuring group sizes and case trim lengths.
8. AmmoFast — Federal .22 LR 40gr Rimfire Ammo, $1.99/box
The good ol’ days of inexpensive rimfire ammo are back! We’ve seen .22 LR prices drop significantly in the last 12 months. And now we can report a new low — the lowest price in years for American-made, name-brand .22 LR ammo. Right now you can buy 50-round boxes of Federal .22 LR ammo for just $1.99! You read that right — under two bucks for fifty rounds of Federal .22 LR 40gr LRN. That works out to four cents per round. This offer is limited to 10 boxes per customer. Check Wikiarms.com for other great .22 LR ammo deals.
We use 1″-diameter Target Spots for sight-in and practice at 100-300 yards. These bright red/orange self-adhesive dots are easy to see. At 100 yards the high-contrast black diamond centers provide precise aiming points. We found this 10-pack of target spots on Amazon at a rock-bottom price. You get 630 total stick-on dots for just $9.65 with FREE Shipping. You can also get 360 Birchwood Casey 1″ dots from Midsouth for just $3.15, but shipping is extra. If you’re already ordering something from Midsouth, you may want to add the dots to your order.
A while back, we featured a portable reloading bench built on a Black & Decker Workmate. That proved a VERY popular do-it-yourself project so we’re showing it again, in case you missed it the first time.
Redding T-7 Still Within Spec
Got QuickLOAD software? Then it’s time to upgrade your data files — new data became available in January 2018. The makers of QuickLOAD offer inexpensive CDs with updated data files (for propellants and projectiles). These data update CDs will add the latest available powder, cartridge, and bullet files to your current version of QuickLOAD/QuickTARGET.
