Do you have .20-Cal fever? Do you yearn to see what a 4200+ fps projectile can do to an unsuspecting prairie dog? Well you could go out and purchase a 204 Ruger rifle, fork over the money for a new, complete die set, and hope that the brass is in stock. Warren B (aka “Fireball”) has a more cost-effective solution. If you have .223 Rem dies and brass, all you need to shoot the 20 Practical is a new barrel and a .230″ bushing to neck down your .223 Rem cases. Warren’s wildcat is simple, easy, and economical. And the 20 Practical matches the performance of the highly-publicized 20 Tactical with less money invested and no need to buy forming dies or fire-form cases. Warren’s cartridge was aptly named. Practical it is.
20 Practical Tikka Bolt Action for Varminting
by Warren B (aka “Fireball”) and Kevin Weaver
After building my 20 PPC, I wanted to do another .20 caliber, this time a repeater for predator hunting that could also serve as a gopher/prairie dog rifle. I wanted to use a Tikka M595 stainless sporter I had. This rifle is the ultimate repeater with an extremely smooth-feeding cycle from its single-column magazine. Since the Tikka was a .223 Remington from the factory, I first looked at possible case designs that would fit the magazine. The 204 Ruger was a very new round at the time and brass was scarce. I also didn’t care for the overly long case design or the standard throat dimensions of the cartridge. I then looked at the 20 Tactical. It was a nice cartridge but I didn’t like the fact that (at the time) an ordinary two-die Tac 20 set with just a plain full-length die and standard seater were $150. Not only did the costs bother me, but I was accustomed to using a Redding die set featuring a body die, a Type-S bushing neck die, and a Competition seater. To be honest, I also didn’t care for the 20 Tactical’s name–there is absolutely nothing tactical about the cartridge. I didn’t want to adopt a new cartridge based on what I perceived to be a marketing gimmick (that “tactical” title).
Warren B, aka “Fireball”, with his Tikka 595. With its smooth action and phenolic single-column mag, it cycles perfectly in rapid fire.
Simply Neck Down .223 Rem to Make a 20-223 Wildcat
I decided the best thing to do for my purposes was to simply neck down the .223 Rem case and make a 20-223. I already had the dies, the brass, and a rifle that would feed it perfectly. I decided to call the cartridge the 20 Practical because as you will see in this article, it truly is a very practical cartridge. In addition to the generous and inexpensive availability of brass and dies, the 20 Practical is an easy case to create, requiring no fire forming as a final step. Simply neck your .223 Rem cases down, load and shoot.
[Editor’s Note: Over the years, other shooters have experimented with .223 Remington cases necked down to .20 caliber, some with longer necks, some with different shoulder angles. Warren doesn’t claim to be the first fellow to fit a .20-caliber bullet in the .223 case. He gives credit to others who did pioneering work years ago. But he has come up with a modern 20-223 wildcat that involves no special case-forming, and minimal investment in dies and tooling. He commissioned the original PTG 20 Practical reamer design, and he and Kevin did the field testing to demonstrate the performance of this particular version.]
I chose Kevin Weaver at Weaver Rifles to fit and chamber the barrel to my rifle. Kevin does excellent work and is great to work with. Kevin liked the idea of the 20 Practical so much he agreed to purchase the project reamer. (BTW Kevin didn’t even need to purchase a Go/No-Go gauge, he just used an existing .223 Rem gauge.)
Before Kevin ordered the reamer, I talked over the reamer specs with him. My priorities were tolerances on the tight end of the .223 Rem SAAMI specification, a semi-fitted neck with no need for neck-turning, and a short throat so that we could have plenty of the 32gr V-Max in the case and still touch the lands. I also wanted this short throat in case [anyone] wanted to chamber an AR-15 for the 20 Practical. A loaded 20 Practical round will easily touch the lands on an AR-15 while fitting into the magazine with no problem. With its standard 23-degree shoulder, the 20 Practical case also feeds flawlessly through an AR-15.
As for the barrel, I only use Liljas on my rifles. I have had great luck with them. They have always shot well and they clean up the easiest of any barrels that I have tried. I had previously sent my Tikka barreled action to Dan Lilja so that he could program a custom contour into his equipment and turn out a barrel that would perfectly fit the factory M595 sporter stock. There isn’t much material on an M595 sporter stock so the contour had to match perfectly and it did. Dan Lilja now has this custom contour available to anyone who would like to rebarrel their M595 sporter with one of his barrels.
There Are Plenty of Good .204-Caliber Varmint Bullet Options
How to Form 20 Practical Cases — Simple and Easy
Forming 20 Practical cases is very easy. No fire-forming is required. Start with any quality .223 Rem brass. Then simply run the case into your bushing die with the appropriate bushing and call it done.
Project Componentry
My 20 Practical rifle started out as a Tikka Model 595 Stainless Sporter in .223 Remington. Though the M595 is no longer imported, if you shop around you can find M595 Sporters for bargain prices. Mine cost under $500. I think the action alone is worth that! The receiver has a milled dovetail for scope rings plus a side bolt release like expensive BR actions. The bolt cycles very smoothly. Ammo is handled with super-reliable 3- or 5-round detachable single-column magazines (FYI, Tikka’s M595 22-250 mags will feed a 6BR case flawlessly.) We kept the standard Tikka trigger but fitted it with a light-weight spring. Now the trigger pull is a crisp 1.8 pounds–about as good as it gets in a factory rifle. We replaced the factory tube with a custom, 24″, 3-groove Lilja 12-twist barrel. Dan Lilja created a special M595 sporter contour to allow a perfect “drop-in” fit with the factory stock. For optics, I’ve fitted a Leupold 4.5-14x40mm zoom in low Talley light-weight aluminum mounts. All up, including optics and sling, my 20 Practical weighs just under 8.5 pounds.
Test Report–How’s It Shoot?
I sent the barrel and barreled action to Kevin and in a very short time it was returned. Kevin did a perfect job on the rifle. I had asked him to try to match the bead blasted finish of the Tikka when he finished the new barrel. It came out perfect and the only way one can tell it is a custom is the extra two inches of length and the “20 Practical” cartridge designation.
So, no doubt you’re asking “how does she shoot?” Is my “prototype”, first-ever 20 Practical an accurate rig? In a word, yes. Even with the standard factory stock, and light contour barrel, it can shoot 3/8″ groups. Take a look at the typical target from this rifle. This is from an 8.5-pound sporter with a very skinny fore-end and a factory trigger.
Gunsmith’s Report from Kevin Weaver The 20 Practical: Origins and Development
Editor’s NOTE: We can’t say for sure who first necked down the .223 Rem to .20 caliber and chambered a rifle for that wildcat (as opposed to the .20 Tactical). But here is an account from way back in 2006 when the Warren B first came up with the idea of a .20 Practical cartridge, complete with reamer specs.
A year ago I received a call from Warren with a great idea. Warren asked “Why couldn’t we simply neck down the .223 Remington case to 20 caliber and get basically the same performance as the 20 Tactical? This way you can forgo the expensive forming dies that are needed for the 20 Tactical.” The idea made perfect sense to me, and I saw no major technical issues, so we got started on the project. I ordered a reamer from Dave Kiff at Pacific Tool & Gauge (PTG) with a .233″ neck. The .233″ neck should allow for a simple necking-down of the 223 Remington case to produce the 20 Practical in just one step. No fire-forming necessary! Furthermore, the PTG 20 Practical reamer Dave created should work with any available .223 Rem brass, commercial or military.
The first 20 Practical round was launched down range (through Warren’s Tikka) just a few months later. The brass formed as easily as expected. All one needs is a Redding type “S” bushing die with a .230 bushing and with just one step I had a .20 caliber case ready to shoot. Warren is brilliant. [Editor’s Note: We concur. For more details on Warren’s case-forming methods and his tips for adapting .223 Rem dies, read the technical sections further down the page.]
It would be almost six months later until I got around to building a dedicated test rifle chambered for the 20 Practical. I used a Remington 722 action, Remington synthetic semi-varmint stock, and a 24″ Douglas stainless steel XX 12-twist barrel. I formed and loaded about 30 cases using Remington brass in about 20 minutes. I used a .223 Rem seating die to seat the 20 Practical bullets. The .223 seating stem seated the small 20-Cal bullets just fine. The first loads sent the 40gr Hornady V-Max bullets down range at a modest 3500 FPS. I did not shoot for groups. I just wanted to use this load to sight in the rifle and break in the barrel. Load development was painless–I used reduced .223 Rem loads for 40gr bullets and worked up from there. In the table below are some of my preferred loads as well as Warren’s favorite recipes for his 20 Practical.
Bullet Wt.
Powder
Charge Wt.
Velocity FPS
Comments
32GR
H4198
24.1
4025
Warren’s lighter gopher load
32GR
AA2460
27.8
4154
Warren’s coyote/prairie dog load
32GR
N133
26.0
4183
Coyote/PD load, clean burn
33GR
H4198
26.0
4322
Hot Load. Use with Caution!
33GR
N133
27.0
4255
Kevin: 0.388” 5 shot group
40GR
H335
25.0
3583
Kevin’s barrel break-in load
40GR
H4198
24.0
3907
Hodgdon “Extreme” Powder
40GR
IMR4895
26.0
3883
Kevin: 0.288″ 5-shot group
40GR
N133
25.0
3959
Kevin: 0.227″ 5-shot group
Warren’s Load Notes: My pet loads are all with IMI cases, 32gr Hornady V-Maxs, and Fed 205 primers (not match). These are the most accurate loads in my rifle so far. I haven’t even bothered with the 40s as I have the 20 PPC and 20 BR for those heavier bullets. I prefer the lighter bullets in the 20 Practical because I wanted to keep speed up and recoil down in this sporter-weight predator rifle. Also, the 32gr V-Max is exceptionally accurate and explosive. I like N133 the best as it burns so clean. IMI cases are tough and well-made.
Kevin’s Load Notes: I used Remington 223 cases, Hornady V-Max bullets, and Remington 6 1/2 primers to develop the above loads. CAUTION: all loads, both Warren’s and mine, should be reduced 20% when starting load development in your rifle. All load data should be used with caution. Always start with reduced loads first and make sure they are safe in each of your guns before proceeding to the high test loads listed. Since Weaver Rifles has no control over your choice of components, guns, or actual loadings, neither Weaver Rifles nor the various firearms and components manufacturers assume any responsibility for the use of this data.
Comparing the 20 Practical and 20 Tactical
Kevin tells us: “The 20 Practical and the 20 Tactical are almost identical cartridges. There are only slight differences in case Outside Diameter, shoulder angle, and case body length. The neck length on the 20 Tactical is a bit longer, but there is still plenty of neck on the 20 Practical to grip the popular bullets, such as the 32gr V-Max. Here are some specs:
Cartridge
Bolt face to shoulder
Shoulder O.D.
Shoulder Angle
Total length
20 Tactical
1.5232″
.360
30°
1.755″
20 Practical
1.5778″
.3553
23°
1.760″
Both the 20 Tactical and the 20 Practical are fine .20 caliber cartridges. Early on, the 20 Tactical was the more popular of the two because it had more publicity. However, my favorite would be the 20 Practical. Warren’s 20 Practical gives the SAME performance as the 20 Tactical without fire-forming, or having to buy expensive forming dies. So with the 20 Practical you do less work, you shell out a lot less money, yet you give up nothing in performance. What’s not to like? To create 20 Practical cases, just buy a .223 Rem Redding Type “S” Bushing Die set with a .230 or .228 bushing and have fun with this great little cartridge.”
If you want to use an AR-platform rifle in the varmint fields, consider getting a 20-caliber barrel chambered for the efficient, low-recoil 20 Practical cartridge. The 20 Practical is simply a .223 Remington necked down to 20 caliber. The parent .223 Rem cartridge of course works great in an AR, but the 20 Practical offers some notable advantages for high-volume varmint shooters. The 20 Practical delivers very high velocity with very low recoil while still providing outstanding accuracy. The 20 Practical is great option for folks who favor “fast and light” — smaller, lower-mass bullets traveling at very high velocities. This little cartridge can launch 40-grainers at over 3900 fps, and 32-grainers even faster. This makes the 20 Practical a great choice for an AR-based varmint rifle.
20 Practical Ultimate Varminter
A decade ago, as a “proof-of-concept”, AccurateShooter.com created a 20 Practical AR15 Ultimate Varminter with a custom 20-caliber upper from Robert Whitley of AR-X Enterprises, LLC. That project rifle was ultra-accurate — every 5-shot group out of the gun was less than the size of a dime. That gun was auctioned off, but Robert Whitley continues to produce custom 20 Practical AR15 uppers. (The 20 Practical cartridge is simply the .223 Rem necked down to 20 caliber — you can use standard .223 brass and load with standard.223 Rem dies. Just swap in a smaller expander and use smaller neck bushings.)
Robert learned that the accuracy of the first 20 Practical AR15 was no fluke. After building six (6) more 20 Practical uppers, he tested them for accuracy and they all shot great. These uppers feature DPMS low-pro receivers with side-charging handles. They are fitted with PacNor 1:11″ twist, 3-groove stainless barrels.
Robert reports: “We have been making more 20 Practical AR15 uppers and I have to say I am astounded by the accuracy of these things. For shooting little tiny groups out of an AR15 with bullets going 3500+ fps, it’s hard to beat the 20 Practical. Today I test-fired six more uppers, all with 11-twist barrels. Three of the uppers had 24″ barrels, two had 20″ barrels, and one had an 18″ barrel (we call it ‘Stubby’).
In four of these uppers I shot re-sized Winchester brass using 25.3 grains of WC844 powder with Berger 40gr BTHP bullets loaded at 2.225″ OAL (about .015″ off the lands). WC844 is inexpensive military surplus powder that is nearly identical to H335. I tried three different primers and the choice did not seem to matter (CCI BR4, Rem 7 1/2s and Win Small Rifle — the old silver ones). All these four uppers shot great.”
Below is an animated GIF with targets from uppers #6, 10, and 11. All groups are mag-fed, 5-shot groups shot at 100 yards using a front rest and rear bag.
Targets Shot with Three Different 20 Practical AR Uppers
For more INFO visit www.6mmAR.com, or email: rcw3 [at] erols.com.
20 Practical Shooters Explain Why They Love this Little Cartridge
A current thread in our Shooters’ Forum focuses on favorite variants of the .223 Rem cartridge. The thread asks: “What is your favorite and most versatile round that you have made from a .223 Rem parent case?” Many cartridges were named, but the wildcat cartridge cited most often was the 20 Practical. Here are some comments by Forum members, who explain the appeal of this great little 20-caliber cartridge:
“The 20 Practical is just a hoot to shoot. Outstanding precision, minimal recoil, easy case forming and inexpensive to shoot. What’s not to like? It’s a great way to introduce kids to centerfire, too.” — JLT
“The 20 Practical for me. Never had as much fun shooting a rifle as I did with the 20 Practical. Also, [it is] the easiest wildcat to form. Just get cases, a couple of bushings to get the right neck tension, and you are shooting.” — NMKid
“Favorite .223 Rem Wildcat? The 20 Practical hands down for me. I have two of them built on Savage actions right now. One has a 20″ BHW barrel and the other has a 26″ Criterion. It is my go-to caliber for shooting up a Prairie Dog town and the ones I have are insanely accurate. Here are some typical 100- and 200-yard groups with my 20 Practicals.” — IA_Shooter
“My favorite was and is the 20 Practical. No fire-forming, no neck-turning, and with the increased BC of the 20 Cal bullets, it’s hard to wipe the smile off your face in a prairie dog town[.]” — Region Rat
“20 Practical and the [original] .223 Rem are my favorites. Accurate, cheap to shoot. The 20 Prac allows you to see your hits and it’s fast.” — Alguapo
“20 Tactical or 20 Practical. Both very easy to reload and/or form from .223 brass. And they are accurate, reach out on varmints at surprising ranges.” — Bill K
Smart Tips on Forming 20 Practical Cases
Varmint ace Warren B, aka “Fireball” in our Forum, explains how to form 20 Practical Cases. “Forming 20 Practical cases is very easy and no fire-forming is required. Start with any good quality .223 Rem brass. One can simply run the case into your bushing die with the appropriate bushing and call it done. I however like to make it a little more involved by doing the neck reduction in steps. I find that taking steps doesn’t overwork the brass as much as one step does. Also, if you resize the neck in too large of a step, sometimes, depending on the neck thickness, the neck will not be dimensionally what you would expect when finished. This is especially important towards the last step when one is getting close to the final required neck diameter.
For my cases the first thing I did was to run them into an old RCBS .223 Rem full length die with the decapping assembly removed. This will take care of any dented necks on the raw cases and bring the necks down to around 0.243″. Since all standard full-length dies oversize the necks way too much, starting with a .223 FL die actually reduces the neck diameter quite a bit–and obviates the need to buy an extra bushing for the first step. I then use my Redding Type-S die with two bushing sizes to get down to where I need to be. In other words, I start with the FL sizer, then move to a Type-S with a 0.233″ bushing and finish with a 0.228″ bushing. Notice how, as I get to the final step, I use progressively smaller increments in size between the reductions.” (Note: Depending on your brass your final bushing size may be different.)
20 Practical vs. 20 Tactical
Varminter Kevin Weaver, who shoots both the 20 Practical and 20 Tactical, states that: “Both the 20 Tactical and the 20 Practical are fine .20 caliber cartridges. However, my favorite would be the 20 Practical. The 20 Practical gives the SAME performance as the 20 Tactical without fire-forming, or having to buy expensive forming dies.
So with the 20 Practical you do less work, you shell out a lot less money, yet you give up nothing in performance. What’s not to like? To create 20 Practical cases, just buy a .223 Rem Redding Type “S” Bushing Die set with a .230 or .228 bushing and have fun with this great little cartridge.
The 20 Practical and the 20 Tactical are almost identical cartridges. There are only slight differences in case outside diameter, shoulder angle, and case body length. Neck length on the 20 Tactical is a bit longer, but there is still plenty of neck on the 20 Practical to grip the popular bullets, such as the 32gr V-Max.”
20 Practical and 20 Tactical Specifications:
Cartridge
Bolt face to shoulder
Shoulder O.D.
Shoulder Angle
Total length
20 Practical
1.5778″
.3553
23°
1.760″
20 Tactical
1.5232″
.360
30°
1.755″
Share the post "Sunday Gunday: 20 Practical AR — Great Accuracy, Low Recoil"
Do you have .20-Cal fever? Do you yearn to see what a 4200+ fps projectile can do to an unsuspecting prairie dog? Well you could go out and purchase a 204 Ruger rifle, fork over the money for a new, complete die set, and hope that the brass is in stock. Warren B (aka “Fireball”) has a more cost-effective solution. If you have .223 Rem dies and brass, all you need to shoot the 20 Practical is a new barrel and a .230″ bushing to neck down your .223 cases. Warren’s wildcat is simple, easy, and economical. And the 20 Practical matches the performance of the highly-publicized 20 Tactical with less money invested and no need to buy forming dies or fire-form cases. Warren’s cartridge was aptly named. Practical it is.
20 Practical Tikka Bolt Action for Varminting
by Warren B (aka “Fireball”) and Kevin Weaver
After building my 20 PPC, I wanted to do another .20 caliber, this time a repeater for predator hunting that could also serve as a gopher/prairie dog rifle. I wanted to use a Tikka M595 stainless sporter I had. This rifle is the ultimate repeater with an extremely smooth-feeding cycle from its single-column magazine. Since the Tikka was a .223 Remington from the factory, I first looked at possible case designs that would fit the magazine. The 204 Ruger was a very new round at the time and brass was scarce. I also didn’t care for the overly long case design or the standard throat dimensions of the cartridge. I then looked at the 20 Tactical. It was a nice cartridge but I didn’t like the fact that (at the time) an ordinary two-die Tac 20 set with just a plain full-length die and standard seater were $150. Not only did the costs bother me, but I was accustomed to using a Redding die set featuring a body die, a Type-S bushing neck die, and a Competition seater. To be honest, I also didn’t care for the 20 Tactical’s name–there is absolutely nothing tactical about the cartridge. I didn’t want to adopt a new cartridge based on what I perceived to be a marketing gimmick (that “tactical” title).
Warren B, aka “Fireball”, with his Tikka 595. With its smooth action and phenolic single-column mag, it cycles perfectly in rapid fire.
Simply Neck Down .223 Rem to Make a 20-223 Wildcat
I decided the best thing to do for my purposes was to simply neck down the .223 Rem case and make a 20-223. I already had the dies, the brass, and a rifle that would feed it perfectly. I decided to call the cartridge the 20 Practical because as you will see in this article, it truly is a very practical cartridge. In addition to the generous and inexpensive availability of brass and dies, the 20 Practical is an easy case to create, requiring no fire forming as a final step. Simply neck your .223 Rem cases down, load and shoot.
[Editor’s Note: Over the years, other shooters have experimented with .223 Remington cases necked down to .20 caliber, some with longer necks, some with different shoulder angles. Warren doesn’t claim to be the first fellow to fit a .20-caliber bullet in the .223 case. He gives credit to others who did pioneering work years ago. But he has come up with a modern 20-223 wildcat that involves no special case-forming, and minimal investment in dies and tooling. He commissioned the original PTG 20 Practical reamer design, and he and Kevin did the field testing to demonstrate the performance of this particular version.]
I chose Kevin Weaver at Weaver Rifles to fit and chamber the barrel to my rifle. Kevin does excellent work and is great to work with. Kevin liked the idea of the 20 Practical so much he agreed to purchase the project reamer. (BTW Kevin didn’t even need to purchase a Go/No-Go gauge, he just used an existing .223 Rem gauge.)
Before Kevin ordered the reamer, I talked over the reamer specs with him. My priorities were tolerances on the tight end of the .223 Rem SAAMI specification, a semi-fitted neck with no need for neck-turning, and a short throat so that we could have plenty of the 32gr V-Max in the case and still touch the lands. I also wanted this short throat in case [anyone] wanted to chamber an AR-15 for the 20 Practical. A loaded 20 Practical round will easily touch the lands on an AR-15 while fitting into the magazine with no problem. With its standard 23-degree shoulder, the 20 Practical case also feeds flawlessly through an AR-15.
As for the barrel, I only use Liljas on my rifles. I have had great luck with them. They have always shot well and they clean up the easiest of any barrels that I have tried. I had previously sent my Tikka barreled action to Dan Lilja so that he could program a custom contour into his equipment and turn out a barrel that would perfectly fit the factory M595 sporter stock. There isn’t much material on an M595 sporter stock so the contour had to match perfectly and it did. Dan Lilja now has this custom contour available to anyone who would like to rebarrel their M595 sporter with one of his barrels.
There Are Plenty of Good .204-Caliber Varmint Bullet Options
How to Form 20 Practical Cases — Simple and Easy
Forming 20 Practical cases is very easy. No fire-forming is required. Start with any quality .223 Rem brass. Then simply run the case into your bushing die with the appropriate bushing and call it done.
Project Componentry
My 20 Practical rifle started out as a Tikka Model 595 Stainless Sporter in .223 Remington. Though the M595 is no longer imported, if you shop around you can find M595 Sporters for bargain prices. Mine cost under $500. I think the action alone is worth that! The receiver has a milled dovetail for scope rings plus a side bolt release like expensive BR actions. The bolt cycles very smoothly. Ammo is handled with super-reliable 3- or 5-round detachable single-column magazines (FYI, Tikka’s M595 22-250 mags will feed a 6BR case flawlessly.) We kept the standard Tikka trigger but fitted it with a light-weight spring. Now the trigger pull is a crisp 1.8 pounds–about as good as it gets in a factory rifle. We replaced the factory tube with a custom, 24″, 3-groove Lilja 12-twist barrel. Dan Lilja created a special M595 sporter contour to allow a perfect “drop-in” fit with the factory stock. For optics, I’ve fitted a Leupold 4.5-14x40mm zoom in low Talley light-weight aluminum mounts. All up, including optics and sling, my 20 Practical weighs just under 8.5 pounds.
Test Report–How’s It Shoot?
I sent the barrel and barreled action to Kevin and in a very short time it was returned. Kevin did a perfect job on the rifle. I had asked him to try to match the bead blasted finish of the Tikka when he finished the new barrel. It came out perfect and the only way one can tell it is a custom is the extra two inches of length and the “20 Practical” cartridge designation.
So, no doubt you’re asking “how does she shoot?” Is my “prototype”, first-ever 20 Practical an accurate rig? In a word, yes. Even with the standard factory stock, and light contour barrel, it can shoot 3/8″ groups. Take a look at the typical target from this rifle. This is from an 8.5-pound sporter with a very skinny fore-end and a factory trigger.
Gunsmith’s Report from Kevin Weaver The 20 Practical: Origins and Development
Editor’s NOTE: We can’t say for sure who first necked down the .223 Rem to .20 caliber and chambered a rifle for that wildcat (as opposed to the .20 Tactical). But here is an account from way back in 2006 when the Warren B first came up with the idea of a .20 Practical cartridge, complete with reamer specs.
A year ago I received a call from Warren with a great idea. Warren asked “Why couldn’t we simply neck down the .223 Remington case to 20 caliber and get basically the same performance as the 20 Tactical? This way you can forgo the expensive forming dies that are needed for the 20 Tactical.” The idea made perfect sense to me, and I saw no major technical issues, so we got started on the project. I ordered a reamer from Dave Kiff at Pacific Tool & Gauge (PTG) with a .233″ neck. The .233″ neck should allow for a simple necking-down of the 223 Remington case to produce the 20 Practical in just one step. No fire-forming necessary! Furthermore, the PTG 20 Practical reamer Dave created should work with any available .223 Rem brass, commercial or military.
The first 20 Practical round was launched down range (through Warren’s Tikka) just a few months later. The brass formed as easily as expected. All one needs is a Redding type “S” bushing die with a .230 bushing and with just one step I had a .20 caliber case ready to shoot. Warren is brilliant. [Editor’s Note: We concur. For more details on Warren’s case-forming methods and his tips for adapting .223 Rem dies, read the technical sections further down the page.]
It would be almost six months later until I got around to building a dedicated test rifle chambered for the 20 Practical. I used a Remington 722 action, Remington synthetic semi-varmint stock, and a 24″ Douglas stainless steel XX 12-twist barrel. I formed and loaded about 30 cases using Remington brass in about 20 minutes. I used a .223 Rem seating die to seat the 20 Practical bullets. The .223 seating stem seated the small 20-Cal bullets just fine. The first loads sent the 40gr Hornady V-Max bullets down range at a modest 3500 FPS. I did not shoot for groups. I just wanted to use this load to sight in the rifle and break in the barrel. Load development was painless–I used reduced .223 Rem loads for 40gr bullets and worked up from there. In the table below are some of my preferred loads as well as Warren’s favorite recipes for his 20 Practical.
Bullet Wt.
Powder
Charge Wt.
Velocity FPS
Comments
32GR
H4198
24.1
4025
Warren’s lighter gopher load
32GR
AA2460
27.8
4154
Warren’s coyote/prairie dog load
32GR
N133
26.0
4183
Coyote/PD load, clean burn
33GR
H4198
26.0
4322
Hot Load. Use with Caution!
33GR
N133
27.0
4255
Kevin: 0.388” 5 shot group
40GR
H335
25.0
3583
Kevin’s barrel break-in load
40GR
H4198
24.0
3907
Hodgdon “Extreme” Powder
40GR
IMR4895
26.0
3883
Kevin: 0.288″ 5-shot group
40GR
N133
25.0
3959
Kevin: 0.227″ 5-shot group
Warren’s Load Notes: My pet loads are all with IMI cases, 32gr Hornady V-Maxs, and Fed 205 primers (not match). These are the most accurate loads in my rifle so far. I haven’t even bothered with the 40s as I have the 20 PPC and 20 BR for those heavier bullets. I prefer the lighter bullets in the 20 Practical because I wanted to keep speed up and recoil down in this sporter-weight predator rifle. Also, the 32gr V-Max is exceptionally accurate and explosive. I like N133 the best as it burns so clean. IMI cases are tough and well-made.
Kevin’s Load Notes: I used Remington 223 cases, Hornady V-Max bullets, and Remington 6 1/2 primers to develop the above loads. CAUTION: all loads, both Warren’s and mine, should be reduced 20% when starting load development in your rifle. All load data should be used with caution. Always start with reduced loads first and make sure they are safe in each of your guns before proceeding to the high test loads listed. Since Weaver Rifles has no control over your choice of components, guns, or actual loadings, neither Weaver Rifles nor the various firearms and components manufacturers assume any responsibility for the use of this data.
Comparing the 20 Practical and 20 Tactical
Kevin tells us: “The 20 Practical and the 20 Tactical are almost identical cartridges. There are only slight differences in case Outside Diameter, shoulder angle, and case body length. The neck length on the 20 Tactical is a bit longer, but there is still plenty of neck on the 20 Practical to grip the popular bullets, such as the 32gr V-Max. Here are some specs:
Cartridge
Bolt face to shoulder
Shoulder O.D.
Shoulder Angle
Total length
20 Tactical
1.5232″
.360
30°
1.755″
20 Practical
1.5778″
.3553
23°
1.760″
Both the 20 Tactical and the 20 Practical are fine .20 caliber cartridges. At present, the 20 Tactical is the more popular of the two because it has had more publicity. However, my favorite would be the 20 Practical. Warren’s 20 Practical gives the SAME performance as the 20 Tactical without fire-forming, or having to buy expensive forming dies. So with the 20 Practical you do less work, you shell out a lot less money, yet you give up nothing in performance. What’s not to like? To create 20 Practical cases, just buy a .223 Rem Redding Type “S” Bushing Die set with a .230 or .228 bushing and have fun with this great little cartridge.”
The new .224 Valkyrie for AR15-platform rifles has garnered lots of attention lately. That new cartridge has gotten people thinking about the options for an AR shooter beyond the venerable .223 Remington (and 5.56x39mm NATO). While the .224 Valkyrie is good for shooting long heavy bullets (such as Sierra’s new 95gr SMK), there is a simpler, cheaper option for folks who favor “fast and light” — smaller, lower-mass bullets traveling at very high velocities. That option is the 20 Practical, which is simply a .223 Remington necked down to 20 caliber. This little cartridge can launch 40-grainers at over 3900 fps. That’s bookin’. This makes the 20 Practical a great choice for an AR-based varmint rifle.
20 Practical Ultimate Varminter
A decade ago, as a “proof-of-concept”, AccurateShooter.com created a 20 Practical AR15 Ultimate Varminter with a custom 20-caliber upper from Robert Whitley of AR-X Enterprises, LLC. That project rifle was ultra-accurate — every 5-shot group out of the gun was less than the size of a dime. That gun was auctioned off, but Robert Whitley continues to produce custom 20 Practical AR15 uppers. (The 20 Practical cartridge is simply the .223 Rem necked down to 20 caliber — you can use standard .223 brass and load with standard.223 Rem dies. Just swap in a smaller expander and use smaller neck bushings.)
Robert reports that the accuracy of the first 20 Practical AR15 was no fluke. After building six (6) more 20 Practical uppers, he tested them for accuracy and they all shot great. These uppers feature DPMS low-pro receivers with side charging handles. They are fitted with PacNor 1:11″ twist, three-groove stainless barrels.
Robert reports: “We have been making more 20 Practical AR15 uppers and I have to say I am astounded by the accuracy of these things. For shooting little tiny groups out of an AR15 with bullets going 3500+ fps, it’s hard to beat the 20 Practical. Today I test-fired six more uppers, all with 11-twist barrels. Three of the uppers had 24″ barrels, two had 20″ barrels, and one had an 18″ barrel (we call it ‘Stubby’).
In four of these uppers I shot re-sized Winchester brass using 25.3 grains of WC844 powder with Berger 40gr BTHP bullets loaded at 2.225″ OAL (about .015″ off the lands). WC844 is inexpensive military surplus powder that is nearly identical to H335. I tried three different primers and the choice did not seem to matter (CCI BR4, Rem 7 1/2s and Win Small Rifle — the old silver ones). All these four uppers shot great. Here is an animated GIF with targets from uppers #6, 10, and 11. All groups are mag-fed, 5-shot groups shot at 100 yards using a front rest and rear bag.”
Targets Shot with Three Different 20 Practical AR Uppers
For more information visit www.6mmAR.com, or contact Robert Whitley via email: rcw3 [at] erols.com.
Share the post "The .20 Practical AR — Wicked Accuracy, Low Recoil"
The new .224 Valkyrie for AR15-platform rifles has garnered lots of attention lately. That new cartridge has gotten people thinking about the options for an AR shooter beyond the venerable .223 Remington (and 5.56x39mm NATO). While the .224 Valkyrie is good for shooting long heavy bullets (such as Sierra’s new 95gr SMK), there is a simpler, cheaper option for folks who favor “fast and light” — smaller, lower-mass bullets traveling at very high velocities. That option is the 20 Practical, which is simply a .223 Remington necked down to 20 caliber. This little cartridge can launch 40-grainers at over 3900 fps. That’s bookin’. This makes the 20 Practical a great choice for an AR-based varmint rifle.
20 Practical Ultimate Varminter
A decade ago, as a “proof-of-concept”, AccurateShooter.com created a 20 Practical AR15 Ultimate Varminter with a custom 20-caliber upper from Robert Whitley of AR-X Enterprises, LLC. That project rifle was ultra-accurate — every 5-shot group out of the gun was less than the size of a dime. That gun was auctioned off, but Robert Whitley continues to produce custom 20 Practical AR15 uppers. (The 20 Practical cartridge is simply the .223 Rem necked down to 20 caliber — you can use standard .223 brass and load with standard.223 Rem dies. Just swap in a smaller expander and use smaller neck bushings.)
Robert reports that the accuracy of the first 20 Practical AR15 was no fluke. After building six (6) more 20 Practical uppers, he tested them for accuracy and they all shot great. These uppers feature DPMS low-pro receivers with side charging handles. They are fitted with PacNor 1:11″ twist, three-groove stainless barrels.
Robert reports: “We have been making more 20 Practical AR15 uppers and I have to say I am astounded by the accuracy of these things. For shooting little tiny groups out of an AR15 with bullets going 3500+ fps, it’s hard to beat the 20 Practical. Today I test-fired six more uppers, all with 11-twist barrels. Three of the uppers had 24″ barrels, two had 20″ barrels, and one had an 18″ barrel (we call it ‘Stubby’).
In four of these uppers I shot re-sized Winchester brass using 25.3 grains of WC844 powder with Berger 40gr BTHP bullets loaded at 2.225″ OAL (about .015″ off the lands). WC844 is inexpensive military surplus powder that is nearly identical to H335. I tried three different primers and the choice did not seem to matter (CCI BR4, Rem 7 1/2s and Win Small Rifle — the old silver ones). All these four uppers shot great. Here is an animated GIF with targets from uppers #6, 10, and 11. All groups are mag-fed, 5-shot groups shot at 100 yards using a front rest and rear bag.”
Targets Shot with Three Different 20 Practical AR Uppers
For more information visit www.6mmAR.com, or contact Robert Whitley via email: rcw3 [at] erols.com.
Share the post "The 20-Caliber Black Rifle — AR Chambered in 20 Practical"
In 2008, as a “proof-of-concept”, AccurateShooter.com created a 20 Practical AR15 “Ultimate Varminter” with a custom 20-caliber upper from Robert Whitley. That project rifle was ultra-accurate — every 5-shot group out of the gun was less than the size of a dime. That gun was auctioned off, but Robert Whitley (AR-X Enterprises, LLC) continues to produce custom 20 Practical AR15 uppers. (The 20 Practical cartridge is simply the .223 Rem necked down to 20 caliber — you can use standard .223 brass and load with standard.223 Rem dies. Just swap in a smaller expander and use smaller neck bushings.)
Robert reports that the accuracy of the first 20 Practical AR15 was no fluke. After buildign six (6) more 20 Practical uppers, he tested them for accuracy and they all shot great. These uppers feature DPMS low-pro receivers with side charging handles. They are fitted with PacNor 1:11″ twist, three-groove stainless barrels.
Robert reports: “We have been making more 20 Practical AR15 uppers and I have to say I am astounded by the accuracy of these things. For shooting little tiny groups out of an AR15 with bullets going 3500+ fps, it’s hard to beat the 20 Practical. Today I test-fired six more uppers, all with 11-twist barrels. Three of the uppers had 24″ barrels, two had 20″ barrels, and one had an 18″ barrel (we call it ‘Stubby’).
In four of these uppers I shot re-sized Winchester brass using 25.3 grains of WC844 powder with Berger 40gr BTHP bullets loaded at 2.225″ OAL (about .015″ off the lands). WC844 is inexpensive military surplus powder that is nearly identical to H335. I tried three different primers and the choice did not seem to matter (CCI BR4, Rem 7 1/2s and Win Small Rifle — the old silver ones). All these four uppers shot great. Here is an overlay with targets from uppers #6, 10, and 11. All groups are mag-fed, 5-shot groups shot at 100 yards using a front rest and rear bag.”
Neck Tension is Important
With four of the uppers, Robert used Winchester brass which had good neck tension, and accuracy was excellent, as shown above. However, for two of the uppers (uppers #3 and #5) Robert used some old 20 Practical ammo that he pulled down and reloaded without re-sizing the case neck. Robert says: “With this old ammo, the neck tension was way too light and the accuracy was so-so, i.e. between .75″-1.0″ at 100 yards — which for a lot of ARs is still considered ‘very good’.” Lesson learned — accuracy may suffer with the 20 Practical if your neck tension is inadequate.
For more information visit www.6mmAR.com, or contact Robert Whitley via email: rcw3 [at] erols.com.
Share the post "20 Practical AR Uppers Deliver Great Accuracy"
Here at AccurateShooter.com, we have promoted the “20 Practical”, a great little cartridge created by simply necking down the .223 Remington to 20 caliber. Popularized for bolt guns by Warren B (aka “Fireball”), the 20 Practical is also an excellent choice for an AR-platform varmint rifle. It offers better ballistics than a .223 Rem, with less recoil, and more velocity. Plus the 20 Practical, by all indications, appears to be an inherently accurate cartridge that “wants to shoot”. Our own AR ‘Ultimate Varminter’ project rifle, developed with Robert Whitley, was chambered as a 20 Practical. That gun shot “lights out”, demonstrating how well the little cartridge works.
Forum member ‘Dennis in VA’ recently put together his own 20 Practical AR with all-premium components. Dennis took his impressive new gun to the range yesterday, and it looks to be a tack-driver. Check out the target below, shot with Sierra 39gr BlitzKing bullets. That’s three shots in 0.375″ edge-to-edge, at 100 yards. (NOTE: regarding this H335 load, we advise to start 10% low and work up.)
Dennis got his upper from Whitley’s AR-X Enterprises. It features a heavy billet upper receiver (with side charging handle), fitted with a 24″ PacNor SS Super Match 11-twist barrel. Mounted to the upper is a +20 MOA, GS-1 Scope Rail from GG&G. Riding on top is a Nightforce 5.5-22X50 NP-R1 scope in Nightforce ultra-light rings.
The lower is equally exotic. Machined from billet by American Precision Arms, it is fitted with with a RRA LPK and a Geissele trigger. The tan, adjustable stock is a Magpul PRS model (Gen II). An Ergogrip tactical deluxe Suregrip completes the build. Dennis in VA has put together a very nice set-up to say the least. And it definitely shoots.
To learn more about the 20 Practical cartridge for AR rifles, visit Robert Whitley’s 20 Practical Webpage. There you’ll find load data, info on dies and reloading, plus advice on hardware and barrel selection. Robert also has a video showing how to form 20 Practical brass.
Share the post "Dennis Builds Another 20 Practical AR Tack-Driver"
AccurateShooter.com has teamed with Robert Whitley and Carl Bernosky to develop a new AR15-based, 20-caliber rifle optimized for varminting. The chambering is a 20-223 with a PT&G (Kiff) reamer, aka the “20 Practical”, a name coined by Warren Brookman*. The cartridge uses standard .223 Remington brass. Case forming is simple — just neck down the brass (Robert did this in two steps, with .233″ and .225″ bushings). You do NOT have to move the shoulder back as with the 20 Tactical. You can even use your existing .223 Rem Redding dies by swapping out some internal components.
While Carl is still working on special (top-secret) “furniture” to help the 20 Practical AR ride the bags, Robert was able to test the first complete 20 Practical AR upper built with a Bartlein barrel. Without any special load development, the gun has proved very accurate, putting 5 rapid-fire shots in a dime-sized group at 100 yards. Robert was using H335 with 40gr bullets. This load runs 3750 fps and Robert thinks more velocity may be possible with H335. We will also test other load recipes for both both 40gr and 32gr bullets. H322 should also be a good choice for both bullet weights. Quickload predicts H322 will send the 32-grainers past 4000 fps, and Warren Brookman says: “For both 32gr and 40gr bullets, Vihtavuori N133 is just about the perfect powder for the 20 Practical. It burns clean, delivers great accuracy and good velocity.”
Robert reports: “I loaded up some new brass today (Winchester brass, factory primed). I only used H335 and the Berger 40 gr BTHP bullets at about .010″ off the lands (2.228″ OAL). The thing is very accurate. First group shot off the bench after sight-in is shown in the video. Keep in mind this was done with no load work-up and I shot fast to ensure the video was not too long. The load was with 26.0 grains of H335 and the Berger 40-grainers going right around 3750 fps.”
If you shoot a .223 Rem currently it’s easy to load for the 20 Practical. You will need a Redding Type ‘S’ neck-bushing full-length sizing die, and Robert recommends a Redding Comp Seater. Then you’ll need some extra bits of kit:
1. Powder funnel that fits .20-Cal case mouths
2. Two neck bushings: .233″ and .225″
3. 20-Caliber cleaning rod with brushes, jag, patches, etc.
4. Decapping rod assembly for 20 Cal (a 204 Ruger one works perfectly — about $15)
*The 20 Practical chambering, a modern 20-223 Wildcat, was popularized by Warren Brookman, whose 20 Practical bolt gun was featured as our 61st Gun of the Week. In that 20 Practical Article, Warren explains the thinking behind the cartridge and shows how to adapt .223 Rem Redding dies.
Share the post "Whitley Shoots New 20 Practical AR"
In 2020, Lapua will again be the title sponsor for the Lapua Practical Rimfire Challenge (LPRC). Modeled after PRS competition, the LPRC features practical-style matches shot with .22 LR bolt-action and self-loading rimfire rifles with optics. There will be four series matches, leading up to the series Finale in October 2020. Shooters will compete for glory plus an impressive table of prizes.
The Lapua Practical Rimfire Challenge Series (LPRC) will be held at the Peacemaker National Training Center in Glengary, WV. The LPRC is designed to test the .22 LR rifle shooter, ammunition, and optics out to 300 yards. While most stages involve long-range positional shooting, shooters will encounter stages set in natural terrain, stages with movement, Olympic stages of fire, and/or smallbore-style stages. Shooters can select from the semi-auto or bolt action division.
Registration for the LRPC is now open, with matches starting in March 2020. For more information on the LPRC visit Peacemakernational.com/prc.
LPRC Match Dates
Match 1: March 21-22
Match 2: May 25-26
Match 3: June 22 – 23
Match 4: July 27- 28
Series Finale: October 5
LPRC Matches Will Feature Multiple Positions and Movement
LPRC series matches are positional shooting events in field conditions out to 300 yards. You can use either a bolt-action or semi-auto .22 LR rimfire rifle. Much like PRS (Precision Rifle Series), competitors will shoot from a variety of positions: prone, strong/weak shoulders, standing, sitting, and kneeling. There will be shots from barricades, and movement from position to position during stages.
LPRC rules will, to a large degree, mirror PRS rules. However, shooters will see some different type of stages than what is normally seen at a PRS match. For example, there may be unsupported standing or unsupported kneeling shots in some stages. Peacemaker’s goal is not to replicate PRS in Rimfire, but rather to create the ultimate challenge for shooters on the rimfire rifle platform.
Rimfire Tactical Matches Aren’t Really New
We’re pleased to see this LPRC shooting discipline — it sounds like fun. However, the concept of a rimfire tactical/practical match is not new — at least on the West Coast. California shooting clubs have been running “Rimfire Tactical” matches for more than a decade. CLICK HERE to read our comprehensive Rimfire Tactical report from way back in 2008. This article includes free targets, ballistics charts, and a complete run-down on suitable rimfire rifles.
The Concept Behind the Rimfire Tactical Match by Bill Erwin
Many guys who shoot long-range tactical matches practice with .22 LR rifles of similar configuration. Rimfire ammo is way more affordable than centerfire, you do not need a big range facility, and shooting rimfire saves wear and tear on your centerfire rifle. Further, for learning how to read the wind, there really is no better training tool than a 22 LR, even as close as 50 yards. Check out this table showing how a .22 LR ballistics compare to .308 Win:
22 LR vs. .308, Distances for Equal 10 MPH Wind Drift
This table shows the corresponding distances at which a 10 mph full-value crosswind pushes a .22 LR bullet and .308 projectile the same amount. Values are based on 0.130 BC for a 40gr .22 LR bullet, and 0.496 BC for 175gr .308 bullet.
22 LR 40gr 1050 fps
50 yd Wind 1.0″
75 yd Wind 2.2″
100 yd Wind 3.8″
125 yd Wind 5.8″
150 yd Wind 8.2″
175 yd Wind 11.0″
200 yd Wind 14.3″
.308 Win 175gr 2650 fps
130 yd Wind 1.07″
180 yd Wind 2.15″
230 yd Wind 3.68″
280 yd Wind 5.63″
330 yd Wind 7.98″
380 yd Wind 10.71″
440 yd Wind 14.56″
This table shows how the .22 LR can be an effective substitute for a .308 Win during training. Because the smaller bullet drifts more in the wind, a 22 rimfire shooter will experience roughly the same crosswind effects as if he was shooting a 175gr .308 twice as far out. So, rimfire work can teach you to dope the wind like a .308, but at less than half the distance. Shooting a .22 LR at 100 yards is like shooting a .308 (with 175 SMK) at 230 yards
SPECIAL BONUS–Rimfire Tactical Precision Targets
These FREE targets by DesertFrog are offered in Adobe Acrobat format for easy printing. CLICK HERE to download all six targets as a .ZIP archive.
Share the post "2020 Lapua Practical Rimfire Challenge in West Virginia"
Mark your calendars for the return of the Civilian Marksmanship Program’s Bianchi Cup International Pistol Tournament! The second longest-running pistol championship in the world, the 2024 CMP Bianchi Cup is set to fire May 21-24, 2024 at the Green Valley Rifle & Pistol Club in Hallsville, Missouri.
Registration for the 2024 Bianchi Cup is now open. Learn more about the 2024 CMP Bianchi Cup and register today at TheCMP.org/bianchicup.
The Bianchi Cup is comprised of four events, including:
The Practical Event, where competitors fire at distances from 10 yards to 50 yards under varying time limits from the shooting line.
The Barricade Event, where competitors fire at targets on either side of the barricade at different distances and under varying time limits from within shooting boxes and behind barricades.
The Falling Plate Event, where competitors fire at eight-inch round steel plates arranged in banks of six at distances from 10 to 25 yards under varying time limits.
The Moving Target Event, where competitors fire from within shooting boxes at distances ranging from 10 to 25 yards at a target moving from left to right, with the target exposed for six seconds.
Competitors shoot from both standing and prone positions and are also required to shoot with both strong and weak hands at various stages. There are no makeup shots in the Bianchi Cup, adding to the challenge.
The annual competition is popularly called the Bianchi Cup — from the trophy named for one of the founders, John Bianchi. Since it’s launch over 30 years ago, the match has become the richest handgun tournament in the world.
NEW FOR 2024! A Rimfire Division has been added to the Bianchi Cup to encourage participation from juniors not shooting centerfire pistols as well as adults who want to warm up for the Bianchi Cup in a less expensive manner. The Rimfire Division offers a memorable Bianchi Cup experience at a fraction of the ammo cost. This division will encompass the same basic rules for each of the current setups — Open, Production/Production Optics, Metallic and Revolver.
Bianchi Cup Open Class Pistol — Features in Review
The Bianchi Cup has been called the most prestigious pistol tournament in the world. Due to the high accuracy required in each stage of the Bianchi Cup, the tournament is considered one of the most difficult handgun championships on the planet.
Bianchi Cup — the Richest Handgun Match on the Planet
Over the past 30+ years the Bianchi Cup has become the richest handgun event in the world, with cash and prizes for the best scores on four stages of fire for both revolver and semi-auto pistol divisions.
Bianchi Cup — Classic Course of Fire
The Bianchi Cup is a combination of Speed and Accuracy. Competitors shoot from both standing and prone positions and are also required to shoot with both strong and weak hands at various stages. Stages may combine stationary and moving targets. The Course of Fire consists of four separate matches:: Practical, Barricade, and Moving Target, and Falling Plates. Each of the four events requires 48 shots to complete. 480 points are possible on each event. Three of the four are scored on the NRA tombstone P1 target. You must hit in the 10-ring or inner X-Ring on EVERY shot to shoot a “clean” 1920.
About the Green Valley Rifle & Pistol Club
The Green Valley Rifle & Pistol Club, formerly the Chapman Training Academy, has been the annual host of the Bianchi Cup since its inception. The origin of the club days back to the 1930s and has played a major role in the creation of the practical shooting discipline. The facility holds several ranges, including two movers, a Bianchi barricade, two 50-yard Bianchi practical ranges, a 250-plus yard rifle range and a falling plates range. CLICK HERE for range information.
Share the post "2024 CMP Bianchi Cup Next Month in Missouri"
Thousands of firearms are on display at SHOT Show 2024, including many that are being showcased for the first time at this major trade show. Today we’re featuring four noteworthy guns — three rifles and one pistol. The new CZ 600 MDT rig could quickly become an important player in PRS/NRL factory class. A new lever gun series was introduced by Smith and Wesson, with two versions, one with a stunning wood stock. Among competition pistols, Walther’s new steel-framed PDP Match model was impressive. And we expect hunters and tactical shooters will like Beretta’s tactical version of its popular BRX1 straight-pull rifle.
CZ 600 MDT Tactical Match
CZ is rolling out an impressive new rifle for the PRS/NRL crowd. The new CZ 600 MDT match rifle combines the popular CZ 600 bolt action with a top-quality MDT alloy stock. We think this is a good option for someone getting started in PRS/NRL competition. In addition the action can be removed and placed in a conventional stock for hunting season.
In this TFB-TV episode, host James Reeves visits CZ headquarters to check out the new CZ 600 MDT. The CZ 600 MDT is a collaboration with MDT Precision, makers of quality precision rifle chassis systems. The CZ 600 series was introduced in 2022, and this is a cool, new variant for the tactical market. TFB-TV states that: “The CZ 600 MDT takes the accuracy and ease of use from the CZ 600 family and marries it to one of two different MDT chassis to bring the CZ 600 into the tactical, military, and PRS realms.”
Smith & Wesson’s New Model 1854 Lever-Action Rifles
At SHOT Show 2024 Smith & Wesson showcased of its first ever modern lever-action rifles, the S&W Model 1854 Series. These new Model 1894 Lever Guns will be offered in multiple formats. Get the basic version with stainless barrel/action and a polymer forearm/buttstock for $1279.00. Or if you have a big budget you can get the limited-edition Model 1854 with polished black PVD finish and very handsome, fully-figured wood for $3499.00 MSRP.
In 1854, Smith & Wesson founders Horace Smith and Daniel Wesson patented their first lever gun. Honoring that historic milestone, the classic American lever gun is reborn as the Model 1854 Series, the first to incorporate the feel of Smith & Wesson’s revered large-frame revolvers, their smooth action, and iconic craftsmanship.
The Model 1854 Series rifles are built with 19¼-inch barrels, are chambered in .44 Rem Mag, and have a capacity of 9+1. The standard Model 1854 has a 410 stainless receiver and a 416 stainless barrel. Key features include M-LOK slots in the fore-end, a 4¾-inch Picatinny base for mounting optics, a flat-face trigger, and removable magazine tube. Additionally, these rifles contain a side loading gate, utilize side ejection, and include a removable mag tube for easier unloading.
Mark Smith, S&W President/CEO states: “These rifles fuse the classic craftsmanship of the iconic lever-action with modern engineering to deliver a platform built on reliability and performance. Our new Model 1854 rifles are a nod to tradition and a testament to Smith & Wesson’s legacy as an American firearms manufacturer.”
The handsome Model 1854 Limited Edition shares the same feature set, but instead of the M-LOK capable fore-end, it boasts a classic high-grade satin walnut finish on both the stock and fore-end and a polished black PVD finish on the receiver and barrel. Both rifles have a 36″ overall length, include a 11/16-24 threaded muzzle, and ship with an XS Sights adjustable ghost ring rear sight and a gold bead front sight.
Walther PDP Steel Frame Match Pistol
We like metal-framed pistols. The extra weight lowers the center of gravity, reduces muzzle flip, and allows faster shot strings. That’s all very valuable if you are shooting pistol matches on the clock. Walther has made a good thing better by creating a full metal version of its popular PDP pistol. The PDP Match metal variant features an extended ergonomic grip and optics-ready slide. The trigger is excellent. This is definitely one of the best 9mm competition pistols on the market.
Intrigued? You’ll find a very thorough review on the All4Shooters.com website. This review includes comprehensive tech details and has good close-up images. The review also includes information on the lesser-priced Walter PDP with polymer grip. As sold in the USA the Walther PDP Match Steel Frame model costs $1,899, shipped with two 20-rd and one 18-rd magazines with aluminum base pads.
Beretta BRX1 Straight-Pull Tactical Version
For 2024, Beretta has introduced a new, camo-finish version of BRX1. This has been dubbed the BRX1 Tactical. Like other BRX1 rifles, this camo BRX1 features a left/right swappable straight-pull action that is very fast to cycle.
In this video, released just last week (1/17/24), the TFB-TV team tests the new Beretta BRX1 Tactical: “This tactical edition, a standout with its multicam finish, is a specialized variant of the Beretta BRX-1, which has gained popularity in Europe for its precision and reliability. The BRX-1 Tactical is enhanced for practical functionality with a 3D printed magazine adapter, allowing it to accept Magpul P-Mags, adding to its versatility.” This video covers the BRX1’s notable features including smooth action, adaptability, and stock ergonomics. The video also compares the new BRX1 Tactical to the original European BRX-1 model, highlighting the main changes — principally the stock configuration and the new bigger magazine.
The new BRX1 Tactical rifle features the same advanced straight-pull action as shown in the BRX1 hunting model below. But the tactical model has a more rugged stock and will hold larger-capacity Magpul P-Mags.
Share the post "Four Impressive New Firearms Featured at SHOT Show 2024"
Started in 1979 by former police officer John Bianchi, the Bianchi Cup is a prestigious and challenging action pistol tournament. The event, the second longest-running action pistol championship, attracts top pistol shooters from around the world. Shooters compete in multiple events including the Barricade, Falling Plate, Practical, and Moving Target.
The Civilian Marksmanship Program (CMP) now oversees the Bianchi Cup. Christie Sewell, CMP Programs Chief, stated: “The Civilian Marksmanship Program is honored and excited to be the governing organization for the historic and treasured Bianchi Cup International Pistol Competition.”
This year’s competition will be held May 23-26 at the Green Valley Rifle & Pistol Club in Hallsville, Missouri. Spectators are invited to attend the championship each day. For more information, visit the CMP 2023 Bianchi Cup Web Page.
Bianchi Cup — the Richest Handgun Match on the Planet
Over the past 30+ years the Bianchi Cup has become the richest handgun event in the world, with cash and prizes for the best scores on four stages of fire for both revolver and semi-auto pistol divisions.
19-Time Bianchi Cup Winner Doug Koenig
Women of the Bianchi Cup
About the CMP Bianchi Cup
The Bianchi Cup International Pistol Tournament was first held in 1979, making it the second longest running action pistol championship in the world. This year, it will be hosted by the CMP for the first time, May 23-26, 2023, at the Green Valley Rifle & Pistol Club in Missouri. The Bianchi Cup has been called the world’s most prestigious pistol tournament. Due to the high accuracy required in each stage of the Bianchi Cup, the tournament is considered one of the most difficult handgun championships on the planet.
The Bianchi Cup is Comprised of Four Events:
Practical Event: Competitors fire at distances from 10 yards to 50 yards under varying time limits from the shooting line.
Barricade Event: Competitors fire at targets on either side of the barricade at different distances and under varying time limits from within shooting boxes and behind barricades.
Falling Plate Event: Competitors fire at eight-inch round steel plates arranged in banks of six at distances from 10 to 25 yards under varying time limits.
Moving Target Event: Competitors fire from within shooting boxes at distances ranging from 10 to 25 yards at a target moving from left to right, with the target exposed for six seconds.
Bianchi Cup Open Class Pistol — Features in Review
Position Shooting with Pistols at Bianchi Cup
Competitors shoot from both standing and prone positions and are also required to shoot with both strong and weak hands at various stages. There are no make-up shots in the Bianchi Cup, adding to the difficulty.
Share the post "2023 Bianchi Cup Competition Runs May 23-26 in Missouri"
After building my 20 PPC, I wanted to do another .20 caliber, this time a repeater for predator hunting that could also serve as a gopher/prairie dog rifle. I wanted to use a Tikka M595 stainless sporter I had. This rifle is the ultimate repeater with an extremely smooth-feeding cycle from its single-column magazine. Since the Tikka was a .223 Remington from the factory, I first looked at possible case designs that would fit the magazine. The 204 Ruger was a very new round at the time and brass was scarce. I also didn’t care for the overly long case design or the standard throat dimensions of the cartridge. I then looked at the 20 Tactical. It was a nice cartridge but I didn’t like the fact that (at the time) an ordinary two-die Tac 20 set with just a plain full-length die and standard seater were $150. Not only did the costs bother me, but I was accustomed to using a Redding die set featuring a body die, a Type-S bushing neck die, and a Competition seater. To be honest, I also didn’t care for the 20 Tactical’s name–there is absolutely nothing tactical about the cartridge. I didn’t want to adopt a new cartridge based on what I perceived to be a marketing gimmick (that “tactical” title). 
Simply Neck Down .223 Rem to Make a 20-223 Wildcat
I chose Kevin Weaver at Weaver Rifles to fit and chamber the barrel to my rifle. Kevin does excellent work and is great to work with. Kevin liked the idea of the 20 Practical so much he agreed to purchase the project reamer. (BTW Kevin didn’t even need to purchase a Go/No-Go gauge, he just used an existing .223 Rem gauge.) 
Project Componentry
Test Report–How’s It Shoot?
Comparing the 20 Practical and 20 Tactical
20 Practical Ultimate Varminter
Varminter Kevin Weaver, who shoots both the 20 Practical and 20 Tactical, states that: “Both the 20 Tactical and the 20 Practical are fine .20 caliber cartridges. However, my favorite would be the 20 Practical. The 20 Practical gives the SAME performance as the 20 Tactical without fire-forming, or having to buy expensive forming dies.
After building my 20 PPC, I wanted to do another .20 caliber, this time a repeater for predator hunting that could also serve as a gopher/prairie dog rifle. I wanted to use a Tikka M595 stainless sporter I had. This rifle is the ultimate repeater with an extremely smooth-feeding cycle from its single-column magazine. Since the Tikka was a .223 Remington from the factory, I first looked at possible case designs that would fit the magazine. The 204 Ruger was a very new round at the time and brass was scarce. I also didn’t care for the overly long case design or the standard throat dimensions of the cartridge. I then looked at the 20 Tactical. It was a nice cartridge but I didn’t like the fact that (at the time) an ordinary two-die Tac 20 set with just a plain full-length die and standard seater were $150. Not only did the costs bother me, but I was accustomed to using a Redding die set featuring a body die, a Type-S bushing neck die, and a Competition seater. To be honest, I also didn’t care for the 20 Tactical’s name–there is absolutely nothing tactical about the cartridge. I didn’t want to adopt a new cartridge based on what I perceived to be a marketing gimmick (that “tactical” title). 
Simply Neck Down .223 Rem to Make a 20-223 Wildcat
I chose Kevin Weaver at 
Project Componentry
Test Report–How’s It Shoot?
Here at AccurateShooter.com, we have promoted the “20 Practical”, a great little cartridge created by simply necking down the .223 Remington to 20 caliber. Popularized for bolt guns by Warren B (aka “Fireball”), the 20 Practical is also an excellent choice for an AR-platform varmint rifle. It offers better ballistics than a .223 Rem, with less recoil, and more velocity. Plus the 20 Practical, by all indications, appears to be an inherently accurate cartridge that “wants to shoot”. Our own 
