Berger Twist-Rate Stability Calculator
On the Berger Bullets website you’ll find a handy Twist-Rate Stability Calculator that predicts your gyroscopic stability factor (SG) based on mulitiple variables: velocity, bullet length, bullet weight, barrel twist rate, ambient temperature, and altitude. This cool tool tells you if your chosen bullet will really stabilize in your barrel.
How to Use Berger’s Twist Rate Calculator
Using the Twist Rate Calculator is simple. Just enter the bullet DIAMETER (e.g. .264), bullet WEIGHT (in grains), and bullet overall LENGTH (in inches). On its website, Berger conveniently provides this info for all its bullet types. For other brands, we suggest you weigh three examples of your chosen bullet, and also measure the length on three samples. Then use the average weight and length of the three. To calculate bullet stability, simply enter your bullet data (along with observed Muzzle Velocity, outside Temperature, and Altitude) and click “Calculate SG”. Try different twist rate numbers (and recalculate) until you get an SG value of 1.4 (or higher).
Gyroscopic Stability (SG) and Twist Rate
Berger’s Twist Rate Calculator provides a predicted stability value called “SG” (for “Gyroscopic Stability”). This indicates the Gyroscopic Stability applied to the bullet by spin. This number is derived from the basic equation: SG = (rigidity of the spinning mass)/(overturning aerodynamic torque).
If you have an SG under 1.0, your bullet is predicted not to stabilize. If you have between 1.0 and 1.1 SG, your bullet may or may not stabilize. If you have an SG greater than 1.1, your bullet should stabilize under optimal conditions, but stabilization might not be adequate when temperature, altitude, or other variables are less-than-optimal. That’s why Berger normally recommends at least 1.5 SG to get out of the “Marginal Stability” zone.
In his book Applied Ballistics For Long-Range Shooting, Bryan Litz (Berger Ballistician) recommends at least a 1.4 SG rating when selecting a barrel twist for a particular bullet. This gives you a safety margin for shooting under various conditions, such as higher or lower altitudes or temperatures.
Story idea from EdLongrange. We welcome reader submissions.
Share the post "Berger Bullets Twist Rate Stability Calculator"
Earlier this week, on July 27th, the CMP held the 2016 Vintage Sniper Rifle Match at Camp Perry. This unique event is a two-man team competition using scoped rifles of WWI and WWII Vintage. This has become of of the most popular rifle matches held at Perry, with 259 teams competing this summer. Many competitors use some version of the M1903 Springfield, but you’ll also see scoped M1 Garands, K31s, Mausers, and even a Lee-Enfield or two. (Semi-Auto shooters are scored separately). This year the Vintage Sniper Match was won by the “Yogi & BooBoo” family team of Silas Fentress and Wesley Fentress, with a 396-13X score. Close behind was runner-up duo Donald Schedler and John Watson (394-13X). Winning the semi-auto division were Brian Dobish and Clayton Maugans (373-8X).
Two-person teams will fire 10 rounds in 20-second intervals from scoped vintage military rifles set on sand bags. One team marksman shoots from the prone position at 300 and 600 yards, while the other serves as a spotter to relay shot position. Marksman and spotter switch positions on the firing lines, allowing each teammate to play both roles. Scores are then combined for an Aggregate team total.
Two M1 Garands, fitted with scopes and lace-on cheekpads.
Who can identify this rifle, with its unusual scope mount?
Our friends at Criterion Barrels have written an interesting article about the 2014 Vintage Sniper Rifle Match. It you want an “insider’s perspective” on the 2014 Match, plus Vintage Sniper gunsmithing tips, read this article. Here are some highlights:
About the Match and the Rifles
The Vintage Sniper Match was the brainchild of Hornady’s Dave Emary. The competition was inspired by his father, a World War II scout sniper, who carried a rifle similar to the 1903A4 rifle builds that can be found today on the Camp Perry firing line. Bob Schanen worked alongside Dave and the CMP staff in establishing the various competition rules prior to the first official Vintage Sniper Match in 2011. The match developers made a point to offer some level of flexibility in rifle configuration, allowing specific types of non-issue optics and rifle rebuilds. This helped make the match more inclusive.
Hornady’s Dave Emary and “Gunny” R. Lee Ermey (right):
Camp Perry — The Venue
The hallowed grounds of Camp Perry have hosted some of the nation’s finest shooters each summer for more than a century. Some of the world’s greatest marksmen have accomplished remarkable feats on the ranges of this lakeside military outpost. Located on the coast of Lake Erie, Camp Perry is positioned just outside of the scenic town of Port Clinton, Ohio. It is our firm belief that every shooter should make the pilgrimage to the Camp Perry at least once in their lifetime. If not participating in an event, visitors should at least make an attempt to meet the competitors, witness the wide selection of firearms used by participants, and pay a visit to the various vendors on base.
Do you have “fuzzy sight syndrome”? Are you frustrated because you can no longer see both your iron sights and your target sharply? Here’s a product that can help. Lyman’s new EyePal is basically an adaptation of aperture or “peep” sights (sometimes called “diopter sights”). The EyePal works by restricting the viewable image to a small-diameter circle. This improves depth-of-field dramatically, which in turn keeps everything in focus, both sights AND Target. This principle has been used for some time with the Merit adjustable optical disc that attaches to shooting glasses with a rubber cup. The EyePal does much the same thing — for a lot less money.
Simply apply the EyePal to any eyewear and you should see an immediate improvement in focus (both near and far). Lyman explains: “The EyePal provides a small image where everything is in focus. This is particularly useful to shooters who have limited near vision but have good far vision. The EyePal enables you to simultaneously see the target, and iron sights — all in focus.”
How Do EyePals Work?
The EyePal is a modern adaptation of the century-old peep sight, which some folks call a pin-hole sight (remember those pin-hole camera experiments back in school?). The EyePal enables you to simultaneously see the target, your front and rear sights — all in focus.
EyePal stick-on apertures are made of a static cling material. This allows EyePals to be easily placed on safety eyewear and prescription glasses without marring the surface or leaving a residue when removed. EyePals are inexpensive (about $25.00 per set), easy to use, and long-lasting.
Share the post "Lyman EyePal Stick-on Peep Sighting System Can Aid Vision"
With the Republican (GOP) Convention recently concluded in Cleveland, readers have asked: “What is the official Republican Party position on the Second Amendment and gun rights?” Here is the section of the Republican Platform concerning gun issues, quoted word for word:
The Second Amendment: Our Right to Keep and Bear Arms
We uphold the right of individuals to keep and bear arms, a natural inalienable right that predates the Constitution and is secured by the Second Amendment. Lawful gun ownership enables Americans to exercise their God-given right of self-defense for the safety of their homes, their loved ones, and their communities.
We salute the Republican Congress for defending the right to keep and bear arms by preventing the President from installing a new liberal majority on the Supreme Court. The confirmation to the Court of additional anti-gun justices would eviscerate the Second Amendment’s fundamental protections. Already, local officials in the nation’s capital and elsewhere are defying the Court’s decisions upholding an individual right to bear arms as affirmed by the Supreme Court in Heller and McDonald. We support firearm reciprocity legislation to recognize the right of law-abiding Americans to carry firearms to protect themselves and their families in all 50 states. We support constitutional carry statutes and salute the states that have passed them. We oppose ill-conceived laws that would restrict magazine capacity or ban the sale of the most popular and common modern rifle. We also oppose any effort to deprive individuals of their right to keep and bear arms without due process of law.
We condemn frivolous lawsuits against gun manufacturers and the current Administration’s illegal harassment of firearm dealers. We oppose federal licensing or registration of law-abiding gun owners, registration of ammunition, and restoration of the ill-fated Clinton gun ban. We call for a thorough investigation — by a new Republican administration — of the deadly “Fast and Furious” operation perpetrated by Department of Justice officials who approved and allowed illegal sales of
guns to known violent criminals.
If you are a gunsmith or work on firearms, you need to read this carefully. The Federal Government, acting through the Department of State Directorate of Defense Trade Controls (DDTC), has imposed significant new burdens on gunsmiths by expanding the definition of “manufacturing”. This is a big deal, as the Arms Export Control Act (AECA) and its implementing rules, the International Traffic in Arms Regulations (ITAR), require firearms “manufacturers” to register with DDTC and to pay a registration fee that (for new applicants) is currently $2,250 per year.
Previously, most small gunsmithing operations that did not export firearms were NOT subject to AECA/ITAR registration requirements. Now, by virtue of a DDTC “Guidance” ruling issued 7/22/2016, ordinary gunsmiths might be required to register as a manufacturer simply because they thread a muzzle or cut a chamber.
The NRA-ILA states: “DDTC is labeling commercial gunsmiths as ‘manufacturers’ for performing relatively simple work such as threading a barrel or fabricating a small custom part for an older firearm. Under the AECA, ‘manufacturers’ are required to register with DDTC at significant expense or risk onerous criminal penalties.” Read NRA-ILA Full Report.
Here is the key language in the DDTC’s “ITAR Registration Requirements – Consolidated Guidance” Ruling of 7/22/2016:
2. Registration Required – Manufacturing: In response to questions from persons engaged in the business of gunsmithing, DDTC has found in specific cases that ITAR registration is required because the following activities meet the ordinary, contemporary, common meaning of “manufacturing” and, therefore, constitute “manufacturing” for ITAR purposes:
a) Use of any special tooling or equipment upgrading in order to improve the capability of assembled or repaired firearms;
b) Modifications to a firearm that change round capacity;
c) The production of firearm parts (including, but not limited to, barrels, stocks, cylinders, breech mechanisms, triggers, silencers, or suppressors);
d) The systemized production of ammunition, including the automated loading or reloading of ammunition;
e) The machining or cutting of firearms, e.g., threading of muzzles or muzzle brake installation requiring machining, that results in an enhanced capability;
f) Rechambering firearms through machining, cutting, or drilling;
g) Chambering, cutting, or threading barrel blanks; and
h) Blueprinting firearms by machining the barrel.
Editor’s Comment: Does this mean that any stock-maker or stock supplier is an ITAR “manufacturer” under part 2(c)? Would installing a scope or accessory rail fall under part 2(a) as “equipment upgrading”? Would fluting a barrel be considered “manufacturing” under part 2(h)?
Impact of New Registration Requirements
As the NRA-ILA (Institute for Legislative Action) reads this, gunsmithing shops (even one-man operations) will now be subject to ITAR regulation though they export nothing: “These requirements apply, even if the business does not, and does not intend to, export any defense article. Moreover, under ITAR, ‘only one occasion of manufacturing … a defense article’ is necessary for a commercial entity to be considered ‘engaged in the business’ and therefore subject to the regime’s requirements.”
As a consequence, these new regulations may drive smaller gunsmithing services out of business: “DDTC’s move appears aimed at expanding the regulatory sweep of the AECA/ITAR and culling many smaller commercial gunsmithing operations that do not have the means to pay the annual registration fee or the sophistication to negotiate DDTC’s confusing maze of bureaucracy. [This is] likely to have a significant chilling effect on activity that would not even be considered regulated.”
Statutory Authority for Registration
The AECA’s statutory requirement for firearms manufacturers to register with DDTC is implemented in Part 122 of the ITAR:
§122.1 Registration requirements.
(a) Any person who engages in the United States in the business of manufacturing or exporting or temporarily importing defense articles, or furnishing defense services, is required to register with the Directorate of Defense Trade Controls under §122.2. For the purpose of this subchapter, engaging in such a business requires only one occasion of manufacturing or exporting or temporarily importing a defense article or furnishing a defense service. A manufacturer who does not engage in exporting must nevertheless register.
Barrel chambering image from Primal Rights, dealer for Desert Tactical Arms.
Share the post "ALERT: Feds Impose ITAR Registration Burdens on Gunsmiths"
The National Shooting Sports Foundation (NSSF) #GUNVOTE program is an important voter registration and education campaign for the November 2016 election. The NSSF’s Gunvote.org website helps visitors register to vote, find a polling place, and determine how candidates stand on gun rights and Second Amendment issues. Quickly find all state and federal candidates in your area with a Zip Code search (or you can search by name). The NSSF’s #GUNVOTE program also provides election news, voter education video resources, and more.
To assist the NSSF’s voter registration and education efforts, Hornady Manufacturing has committed $250,000 in support of #GUNVOTE programs. This is the largest donation the #GUNVOTE campaign has received to date.
“For the first time in our nation’s history, we have a Presidential candidate who is openly running against the lawful commerce in firearms, which is a prerequisite to our ability to exercise our Second Amendment rights,” said Stephen Hornady, President of Hornady Manufacturing. “It is vital that America’s hunters, target shooters and all gun owners become educated on what the candidates are saying and that’s why the #GUNVOTE initiative of our industry is so important. Our company is proud to be a part of this cooperative effort.”
We support the NSSF’s efforts to inform the public and help gun owners register to vote. This is a very important election for firearms owners and supporters of the Second Amendment. As the NSSF explains: “With the balance of the Supreme Court at stake, this election will affect our constitutional rights. It is crucial that all gun owners and Second Amendment supporters register to vote, become informed about candidates’ positions, and on Election Day, #GUNVOTE.”
Share the post "GUNVOTE Program Promotes Voter Registration and Education"
The Savage A17 17 HMR rifle was named American Hunter’s 2016 Rifle of the Year. And we understand why. This little rifle is a hoot to shoot. The model we tested proved reliable and quite accurate with the new 17 HMR ammo developed by CCI expressly for the A17. After the first production run Savage made a few tweaks to the A17’s magazine well; this has resulted in very good reliability with current models.
When the A17 was released, a rather whimpy, Tupperware stock was the only option. The Length of Pull (LOP) was a bit short for a full-sized adult and the short, narrow fore-arm was less than ideal when used with a front rest or sandbag. Savage now offers laminated wood stocks from the factory, but most of the A17s that have been sold to date have the black plastic stock. But don’t worry… you can re-stock your A17 for under $130.00.
Now, thanks to Boyds Gunstocks, there are some good, very affordable stock options for the A17. Boyds has introduced Savage A17 replacement gunstocks in multiple styles: Savage Classic, Featherweight Thumbhole, Heritage, Platinum, Prairie Hunter, Pro Varmint, and Varmint Thumbhole designs. Five of these styles are shown in the photos above. Nearly all of Boyd’s laminated wood Savage A17 stocks are just $129.00 with a few left-hand versions priced at $144.00 (still a bargain). For field use, we like the Varmint Thumbhole because it has a comfortable grip and a longer, straight fore-end that works well with either sandbags or bipod. For target work, we favor the Pro Varmint stock. This stock features a relatively straight toe on the buttstock that is very steady on a rear bag.
Boyds plans to offer a variety of options for their Savage A17 stocks. These will include new custom wood options, custom length of pull, and an adjustable comb. In addition, as with other Boyds stocks, a wide selection of laminated wood colors are available. Boyds recently released eight new laminate wood color options including Sage, Prairie Wind, Ripple Timber, Ripple Forest Camo, Ripple Blaze, Ripple Royal Jacaranda, Ripple Sky and Ripple Zombie.
Share the post "Quality, Affordable Laminated Wood Stocks for Savage A17"
The NRA High Power Championship cycle commences August 1, 2016. Want to follow the action at the National Matches at Camp Perry? The NRA maintains a webpage with the latest results for all the National rifle and pistol matches at Camp Perry. Click any of the links below to launch a page with match-by-match results. Once you navigate to the appropriate results page, click the particular match title (or 3-digit match number) to open a table with ranked lists of competitors and their scores. For example, the National High Power Rifle Championship is Match number 400.
Tubb 2000 rifle, left-hand version. Note how the butt-plate is adjusted for cant, angle, and drop.
Over $25,000 Worth of Prizes at 2014 NRA Springfield M1A Match
The Springfield M1A Match will be held Sunday, July 31, 2016 (the day after the CMP Garand Match). Sponsored by Springfield Armory, this popular event features big-money payouts and valuable hardware prizes. More than $25,000 in cash and prizes were awarded, with categories for shooters of all skill levels. There was a big turn-out for the event. Competitors were treated to bright, sunny skies yesterday. Here are photos from the match, courtesy NRA General Operations.
Share the post "Camp Perry Calendar — Keep Track of All the Action in Ohio"
If you haven’t checked out NormaUSA’s website, you should. There you’ll find Norma’s Cartridge of the Month Archive. This great resource provides a detailed history of popular cartridges, along with a discussion of these cartridges’ hunting and target-shooting uses. There are currently 26 Cartridge of the Month articles, the latest featuring the mighty .500/.416 Nitro Express cartridge.
Also on Norma-USA.com you’ll find information on Norma cartridge brass, bullets, powder and factory ammo. The site also offers a video archive plus links to Norma Reloading Data.
A mild cartridge by modern standards, the 6.5×55 has impressive credentials in both the hunting field and in competition. It was developed jointly by Sweden and Norway in 1894 – one of the very first smokeless, small-bore rounds for military rifles. When Sweden boosted 6.5×55 performance in Mausers, Norway stayed with original loads in the less robust Krag. The 6.5×55 defended Scandinavia for most of a century thereafter. In 1990 the National Rifle Association of Denmark, Norway and Sweden renamed this cartridge the 6.5×55 SKAN and standardized its specifications. Still hugely popular among moose hunters there, it has also excelled in 300-meter free-rifle competition.
The long tenure of this cartridge spanned the post-war wildcatting era. Unfortunately for shooters keen to make something new of the 6.5×55 hull, its head diameter is .01 greater than that of the 7×57 (and the .270 and .30-06). The rim is thicker too. At 2.16 inches, cases mike .15 longer than the .308’s and .08 shorter than those of the 7×57 – though as originally loaded, its overall length (3.15 inches) exceeds that of the 7×57. In fact, it falls just 0.1 inch shy of the finished length of the 7mm Remington Magnum! In my view, the 6.5×55 merits at least a mid-length action, such as on Melvin Forbes’s New Ultra Light rifles. Shorter (typical .308-length) actions require deep bullet seating that throttles performance.
You’ll look hard to find a better deer cartridge than the 6.5×55. Francis Sell, woodsman and rifle enthusiast whose book on blacktail deer hunting has no peer, favored the 6.5×55. Hunters coming of age in a magnum culture might question the round’s bona fides on animals as stout as elk and moose. But at modest ranges, with bullets like Norma’s factory-loaded 156-grain Oryx, it’s a sure killer. Modest recoil makes rifles pleasant to fire (read: accurate in hand!) and fast on follow-ups. In Africa the 6.5×55 – and similar 6.5×54 Mannlicher-Schoenauer – felled much bigger game than moose long before anyone necked down the .375 H&H! While its compact case won’t let the Swede match the likes of the .270 ballistically, it is a fine all-around choice for big game in the Lower 48.
Share the post "Norma Cartridge of the Month: 6.5×55 Swedish"
With the price of premium brass topping $1.00 per case for popular match cartridges, it makes sense to consider annealing your brass to extend its useful life. You don’t want to chuck out brass that costs a buck a case (or more)! Forum member Darrell Jones offers a full range of brass prep, brass forming, and brass restoration (annealing, ultra-sonic cleaning) at very affordable prices. Starting at just $20 per 100 cases ($25/100 for magnum cases), Darrell’s company, DJ’s Brass, will anneal your used brass using state-of-the-art Bench-Source annealing machines. Annealing plus ultrasonic cleaning starts at $35 per 100 cases ($45 for magnum cases). For a bit more money Darrell can also uniform the primer pockets and chamfer the case necks.
Custom Neck-Turning Services
Another great service DJ’s Brass provides is precision neck-turning. Darrell can neck-turn any size case to your specified neck-wall thickness. The price starts at $60.00 per hundred for standard cases or $75.00/100 for magnum size with a $25.00 minimum order. And if you’ve got a bucket of brass to neck-turn, that’s fine with Darrell — he recently neck-turned 1500 pieces of brass for one customer!
DJ’s Brass can process everything from .17 Fireball all the way up to the big magnum cases. And the job gets done quickly. Darrell normally offers a 10-day turn-around. For most jobs, Darrell tells us, he gets the processed brass to the Post Office within three business days. For more info, visit DJsBrass.com or call Darrell Jones at 205-461-4680. IMPORTANT: Contact Darrell for shipping instructions BEFORE sending any brass for processing. ALL BRASS MUST BE DE-PRIMED before you send it.
• Anneal Case Necks Only ($20.00/100 normal or $25.00/100 magnum)
• Ultrasonic Cleaning, Check Necks, and Annealing ($35.00/100 normal or $45.00/100 magnum)
• Full Service: Uniform primer pockets, Chamfer case mouths, Ultrasonic cleaning and Polishing, Anneal case necks (Starting at $50.00/100 call for quote)
• Neck Turning or trim-to-length Custom Order Service (Starting at $60.00/100 for standard cases and $75.00/100 for magnums)
• Hydro-Form Specialty cases (such as Dasher) $0.60 (sixty cents) each minimum of 100 pieces plus actual return shipping cost
• Expand Case Necks and Anneal brass (Call for Price)
• Create False Shoulder for Fire-Forming (Call for Price)
• Ultrasonic Cleaning of Muzzle Brake, $5.00 plus actual shipping
Hydro-Forming Cartridge Brass
Hydro-forming by Darrell costs $0.60 per case with a minimum order of 100 pieces. After hydro-forming, Darrell can also neck-turn the case for an additional charge (call for combined quote). In addition to the 6mmBR-based cases shown below, Darrell can now hydro-form 6PPC cases from .220 Russian brass.
With Darrell’s hydro-forming service you don’t have to buy any special dies or other equipment. Darrell says: “Simply send me the brass you need or have it dropped-shipped to me along with a fired case that has not been sized. If you need formed brass for a new build (gun not yet fired), let me know and I will size the brass to fit within .001″ of a PT&G GO gauge.”
DJ’s Brass Offers Specialized Custom Services
Darrell tells us: “At DJ’s Brass, we can handle all your brass refurbishing needs. From ultrasonic cleaning to custom annealing for specific wildcat cartridges. We can expand your necks from .22 caliber to .30 caliber and anneal shoulders for consistent bump-back. We can turn your case-necks and trim the brass to your specs. For some cartridge types, I can pre-form cases to assist in fire-forming a wildcat cartridge. We also remove the carbon build-up in muzzle brakes. Don’t lose your accuracy by having carbon build up and close off the clearance required for the most accurate bullet release through a muzzle brake.” Note: Extra charges apply for neck-turning and neck expansion operations, or specialized cartridge-forming operations. Please call Darrell at 205-461-4680 for special services pricing.
Share the post "DJ’s Brass Can Anneal, Turn Necks, Hydro-Form Cases and More"
Here’s big news in the gun industry. In a $95 million cash deal, Smith & Wesson Holding Company (Nasdaq: SWHC) will acquire Crimson Trace Corporation (CTC), the industry leader in firearms laser sights and tactical lighting. Once the acquisition is finalized, CTC will operate as Smith & Wesson’s new Electro-Optics Division, headed by Lane Tobiassen, CTC’s current President and CEO. Jeffrey Buchanan, Executive VP and CFO of Smith & Wesson, stated, “We intend to complete the purchase of Crimson Trace with cash on hand and we expect the transaction to close in three to six weeks.”
This deal makes sense for both parties. In the past 12 months, CTC earned $44 million, with a quarter of that coming from Smith & Wesson. CTC President/CEO Lane Tobiassen will serve as President of S&W’s new Electro-Optics Division. The Crimson Trace management team and workforce, as well as its base of operations, will remain in Wilsonville, Oregon after the acquisition. Smith & Wesson Holding Corporation (SWHC) will purchase all of the outstanding stock of Crimson Trace for $95.0 million in cash.
Two Decades of Innovation and Growth for CTC
Founded 22 years ago, Crimson Trace is now the firearms industry leader in laser sighting system and tactical lighting. CTC currently offers more than 225 products, including: Lasergrips®, Laserguard®, Rail Master® platforms, Defender Series®, Lightguard®, and the new LiNQ™ wireless activation system. With its ever-expanding product line, CTC has generated a 10-year compound annual revenue growth rate in excess of 10%.
CTC offers cutting-edge technology, including LiNQ™, the world’s first wirelessly-controlled laser + white light system. LiNQ™ combines a green laser sight and 300-Lumen LED white light for AR-Type Modern Sporting Rifles. The laser and light are controlled wirelessly via handgrip buttons.
Top Crimson Trace and S&W Executives Speak Out:
CTC President/CEO Lane Tobiassen said: “It is a great honor to lead Crimson Trace into this exciting new chapter in our history by joining the Smith & Wesson team. Since 1994, we have designed and brought to market more than 225 products[.] As the new Electro-Optics Division of Smith & Wesson, we believe that our capabilities, combined with inorganic opportunities to acquire related technologies, will expand the reach of our existing market footprint. This makes us a great fit for Smith & Wesson, a legendary company with an iconic brand[.]”
James Debney, Smith & Wesson President and CEO said, “Crimson Trace provides us with an exceptional opportunity to acquire a thriving company that is completely aligned with our strategy to become a leader in the market for shooting, hunting, and rugged outdoor enthusiasts. As the undisputed leader in the market for laser sighting products, Crimson Trace serves as an ideal platform for our new Electro-Optics Division.”
Share the post "Smith & Wesson Acquires Crimson Trace for $95 Million"
Ruger has donated $4,000,000.00 to the NRA-ILA (Institute for Legislative Action), based on Ruger’s pledge to donate $2.00 for every new Ruger firearm sold between the 2015 and 2016 NRA Annual Meetings. Ruger called this the “2 Million Gun Challenge”.
Ruger met the challenge goal of selling two million new firearms, thereby generating a total donation of $4,000,000. Ruger CEO Mike Fifer and President Chris Killoy presented Chris Cox, NRA-ILA’s Executive Director, with a check for $4,000,000 at the 2016 NRA Annual Meetings in Louisville, Kentucky. Cox praised Ruger’s Challenge Program: “The funds raised from this program will help us in both our fight to protect America’s Second Amendment and our effort to educate voters and get them to the polls this crucial election year.”
During the challenge period, one of the largest distributors of Ruger firearms, Davidson’s / Gallery of Guns, also pledged to donate $1.00 for each new Ruger firearm sold through its distributorship. Davidson’s effort added more than $350,000 to the NRA-ILA cause.
Ruger 2 Million Gun Challenge Becomes 2.5 Million Gun Challenge
Both Ruger and Davidson’s have pledged to extend the challenge period through the end of October, to ensure continued support up until the election. Ruger hopes to sell another 500,000 new firearms (by the end of October 2016) with a $2.00 donation per gun. If Ruger meets its challenge, that would generate another $1 million in NRA-ILA donations, for a total of $5,000,000 for the 2015-2016 period.
For more information on the Ruger 2.5 Million Gun Challenge, visit Ruger.com/2Million.
Share the post "Ruger Gives $4 Million to NRA-ILA and Pledges $1 Million More"
Berger Twist-Rate Stability Calculator
To assist the NSSF’s voter registration and education efforts, Hornady Manufacturing has committed $250,000 in support of #GUNVOTE programs. This is the largest donation the #GUNVOTE campaign has received to date.
With the price of premium brass topping $1.00 per case for popular match cartridges, it makes sense to consider annealing your brass to extend its useful life. You don’t want to chuck out brass that costs a buck a case (or more)! Forum member 
This deal makes sense for both parties. In the past 12 months, CTC earned $44 million, with a quarter of that coming from Smith & Wesson. CTC President/CEO Lane Tobiassen will serve as President of S&W’s new Electro-Optics Division. The Crimson Trace management team and workforce, as well as its base of operations, will remain in Wilsonville, Oregon after the acquisition. Smith & Wesson Holding Corporation (SWHC) will purchase all of the outstanding stock of Crimson Trace for $95.0 million in cash.
