Shiney Savings: Wet-Tumbling Cartridge Brass on a Tight Budget
Super Clean Brass Without Breaking The Bank
Posted on June 21, 2017 by Sierra Bullets
Written by Sierra Bullets Ballistic Technician Gary Prisendorf
I recently purchased 1,000 rounds of once-fired 5.56 LC brass that was fully processed and ready to load. The brass had been wet tumbled, using stainless steel pins and looked great inside and out, including the primer pockets.
I had always used a vibrating tumbler with either corn cob or walnut media and I always thought my brass looked pretty good until I saw what the wet tumbling and pin combination did.
Being the budget minded reloader that I am, I started looking for a cheap way to wet tumble my brass using stainless steel pins. Harbor Freight had recently opened a store nearby and I had received coupons in the mail, one of the coupons was 20% off any one item.
So I headed for the Harbor Freight store and after roaming around for 20 minutes or so I found a dual drum rotary rock tumbler for $55.00 and thought it would do just fine for what I was planning. The drums are rather small and only have a 3 pound maximum load limit each, but I figured that was big enough for around 150 .223 cases or maybe 300 9MM cases at a time.
I pulled the wrinkled up coupon out of my pocket, paid, and walked out with my new $47.00 brass cleaning machine. I didn’t have any stainless steel pins and couldn’t find any locally. At our local hardware store I picked up some brass plated ½” finishing brads that I thought might work until I could get some pins ordered.
I bought two small packages of the finishing brads(1.75 oz.), for $1.69 each then headed to my local Walmart to pick up some Dawn dish soap (.99 cents) and a bottle of Lemi Shine ($3.27). I had read online that is what a lot of people use for cleaning their brass.
I bought two small packages of the finishing brads (1.75 oz.), for $1.69 each then headed to my local Walmart to pick up some Dawn dish soap (.99 cents) and a bottle of Lemi Shine ($3.27). I had read online that is what a lot of people use for cleaning their brass.
When I got home, I started depriming .223 brass for my new toy, I mean brass tumbler. I deprimed 100 cases, put 50 in each drum, dropped a package of brads in each one, filled them ¾ of the way with water, gave each drum a small squirt of Dawn dish soap and a tablespoon of Lemi Shine. I sealed up the drums and fired up the tumbler.
After an hour and a half, I just couldn’t stand it any longer and had to see the results. The water was filthy but the cases were super clean, I couldn’t be happier. For a total investment of around $55.00, I can now get my cases looking almost new.
Here are the before and after pictures of my first run of brass:
I have since ordered two pounds of stainless steel pins, I put one pound in each drum. To be honest the brass really doesn’t look any better, but the pins don’t seem to get stuck inside of the cases near as bad as the brass-plated brads did.
Tip: Make sure to inspect your cases and look inside each case to ensure all of the brads/pins are removed.
Just lay the brass and brads/pins out on a towel and let them dry. Mine were dry after about 12 hours.
If you want your cases to look like new without breaking the bank, give it a try. You can’t clean 1000 at a time like the $200.00 tumbling machines that are made for specifically for brass, but this is a much cheaper alternative and the results speak for themselves. — Gary Prisendorf, Sierra Bullets
EDITOR: Actually you can get a machine for a whole lot less than $200.00! See the next paragraph.
Lyman Cylone Rotary Tumbler with Factory Rebate
Sierra’s Technician got his rotary tumbler and brass media for $55.00. For about twice that you can get a much better, higher-capacity system from Lyman. The Lyman Cyclone Rotary Tumbler features a large, polymer drum that holds up to 1000 .223 Rem cases. The kit includes media separation trays, plus five pounds of correct STAINLESS media. The Lyman Cyclone system costs $156.54 delivered from Amazon but this product qualifies for a $25 REBATE from Lyman. That puts your net cost at $131.54 for a complete Cyclone system. To be honest we think that’s money well spent, compared to the “El Cheapo” Harbor Freight unit. The Lyman will run six times as many .223 Rem cases, and get the job done faster. We suspect long-term durability will be better with the Lyman tumbler as well.
Similar Posts:
- Bargain Basement Brass Tumbling System — Under $60 Invested
- New Lyman Cyclone Rotary Tumbler with Dual Media Separators
- How to Clean Brass by Wet-Tumbling — Plus Drying Methods
- Wet-Tumbling Cartridge Brass — Some Smart Solutions
- Wet-Tumbling Cartridge Brass — Tips for Great Results
Share the post "Shiney Savings: Wet-Tumbling Cartridge Brass on a Tight Budget"
Tags: Brass Tumbling, Cartridge Brass, Cylcone, Harbor Freight, Lyman, Lyman Rebate, Stainless Media, Tumbler, Wet Tumbling
This is just the kind of article that I would like to see more of. Both the author and editor made useful contributions. Well done.
The HF version works great, mine has paid for itself many times over. Running as I type cleaning up some 44 mag brass i picked up at an auction tonight. I’m by no means a high volume centerfire shooter, so the HF version is more than adequate for me, and beats the hell out of a vibratory tumbler.
One word of warning for the HF setup. At least on mine, it has enough torque to run the tubs when they’re loaded, but it doesn’t have enough torque to start them when it is off. I turn mine on, then drop the tubs in, runs fine after that. However, if the unit loses power, it will not be able to start the rotation again, meaning the motor is on but not moving, and will likely heat up very quickly and/or burn out. Consequently, I only ever run mine when I’m home, I never leave it running when I go out.
Put the tubs on and spun them with one hand while turning the switch on with the other. Saves stress on the belts which some have had trouble with breaking. Got mine for $35. Works great. Nice article cause I’m a cheapo.
How clean was the inside of the brass?