18 « October « 2017 « Daily Bulletin

teslong borescope digital camera barrel monitor

As an Amazon Associate, this site earns a commission from Amazon sales.

October 18th, 2017

Stop Neck Sizing! Why You Should Full-Length Size Your Brass

Full-Length Sizing Erik Cortina Neck Sizing Video

Why It’s Smart to Full-Length Size Your Brass

Commentary by Erik Cortina

Should You Full-Length Size Your Cartridge Brass?

Absolutely. Let Me Explain Why…

I have seen it time and time again, shooters on the line wrestling with their rifle trying to get the bolt closed while the wind is switching. They were too focused trying to get their bolt to close and getting their rifle settled back on the bags that they missed the wind switch. Bang… Eight! The straw that broke the camel’s back for me was at the 2017 Canadian Nationals. I was paired up with a young girl and she would try really hard to close the bolt on her rifle. The majority of the time she would get it to close, but often times she could not even get the round to chamber. She was focused on her rifle the entire time rather than on the conditions. When we completed our strings, she had five rounds that did not chamber out of 15! That is way too many! I told her she needed to think about full-length sizing with 0.002″ shoulder bump, or Controlled Full-length Sizing like I call it. I told her not to worry about losing accuracy. I told her that I full-length size all my rounds and asked if she noticed how smooth my bolt was and noticed my score. She said yes, they were both great!

Controlled Full-length Sizing Does NOT Harm Accuracy
I have found that Controlled Full-length Sizing does NOT hurt accuracy or shorten brass life. I find that I can focus much more on the conditions when I don’t have to think about chambering a round nor extracting it. It has become second nature. After firing, I keep my head welded to the stock, I open the bolt by placing my thumb on top of stock and rotating hand upwards. I reach in and retrieve spent case, place it back in ammo box, and pick up another loaded round and put in chamber. I verify conditions and when ready, I push the bolt in and close it with my index and middle finger.

With Controlled Full-length Sizing you “bump” the shoulder around .002″ for bolt guns.*
full length sizing
Image courtesy Sinclair International which carries a variety of Full-length dies.

Full-Length Sizing Erik Cortina Neck Sizing Video

Whidden Full-Length Sizing Dies
by AccurateShooter.com Editor
For proper Full-length sizing, you want a quality die that’s a very good match to your chamber. For our project rifles we usually turn to Whidden Gunworks which offers both bushing and non-bushing FL dies. And if you want the hot new option, check out Whidden’s patent-pending, click-adjustable FL-sizing die. This gives instant, precise control over shoulder bump. It works great.

*With gas guns, such as the AR10, you may want to increase shoulder bump to .003″ or more. With some benchrest cartridges, .0015″ bump may prove optimal. But .002″ is a good starting point.

Permalink Bullets, Brass, Ammo, Gear Review, Reloading 11 Comments »

October 18th, 2017

Bore Cleaning The Right Way — Top Barrel-Makers Give Advice

Shooting Sports Lohman Barrel

Ask 10 shooters about barrel cleaning and you’ll get 10 different opinions. This reflects that fact that different fouling problems demand different solutions. For example, solvents that work well for copper may not be the best for hard carbon (and vice-versa). To come up with the right solution, first you must understand the nature of the fouling in your barrel.

CLICK HERE to read Full Match Barrel Care Article »

Chip Lohman, former Editor of Shooting Sports USA Magazine, has authored an excellent article on barrel maintenance and cleaning. Chip’s article, Let the BARREL Tell You — Match Barrel Care, is in the Shooting Sports USA digital archives. In this article, Chip shares the knowledge of a dozen experts including respected barrel-makers Frank Green (Bartlein Barrels), John Krieger (Krieger Barrels), Dan Lilja (Lilja Barrels), and Tim North (Broughton Barrels).

John Krieger Interview with AccurateShooter at SHOT Show:

The debate about the proper care of a match barrel is a hot one, spiked with folklore and old wives’ tales, Lohman said. He and his staff set out to set the record straight: “We tried to interject some science into the discussion of cleaning a match barrel,” he explained. In his article, Lohman writes:

Why worry about a little barrel fouling when the throat is subjected to a brutal 5,600° F volcano at 55,000 PSI? To investigate these and other questions about taking care of a match barrel, we spoke with a dozen experts and share their knowledge in this first of a series of articles.

After listening to folks who shoot, build barrels or manufacture cleaning solvents for a living, we concluded that even the experts each have their own unique recommendations on how to care for a match barrel. But they all agree on one thing — the gun will tell you what it likes best. Because the life expectancy of a match barrel is about 1,500 to 2,500 rounds, the objectives of cleaning one should include: preserve accuracy, slow the erosion, and remove fouling — all without damaging the gun. This article doesn’t claim that one cleaning method is better than the next. Rather, we set out to interject a little science into the discussion and to share some lessons learned from experts in the field.

For more Shooting Sports USA articles, visit www.ssusa.org.

Permalink - Articles, Tech Tip No Comments »

October 18th, 2017

Gear Spotlight: New Gun Cleaning Rod Case from MTM

Here’s a cool new product that will make it easier to stow and/or transport your precious cleaning rods. Sure you can tuck a single rod in a gun case, but what if you want to carry a variety of rods to the range? This case holds up to four (4) rods securely, and keeps solvent residues off your fine firearms.

MTM’s new Gun Cleaning Rod Case is capable of storing four rifle or shotgun cleaning rods up to 47″ long. Each rod is held in an individual slot and there are foam inserts on either end, making transportation secure and rattle-free. You don’t have to worry about the rods banging into each other. We like the fact that MTM has cleverly included multi-sized “corrals” to hold patches from large to small. Plus there is plenty of room to hold jags and brushes.

MTM explains the benefits: “Long gun enthusiasts no longer have to fumble and search for miscellaneous cleaning equipment since it will all be in an easy to access container.”