How to Clean Cartridge Brass with Ultrasonic Cleaning Machines
Tumblers and walnut/corncob media are old school. These days many shooters prefer processing brass rapidly with an ultrasonic cleaning machine. When used with the proper solution, a good ultrasonic cleaning machine can quickly remove remove dust, carbon, oil, and powder residue from your cartridge brass. The ultrasonic process will clean the inside of the cases, and even the primer pockets. Tumbling works well too, but for really dirty brass, ultrasonic cleaning may be a wise choice.
READ FULL UltimateReloader.com Article on Ultrasonic Case Cleaning.
Our friend Gavin Gear recently put an RCBS Ultrasonic cleaning machine through its paces using RCBS Ultrasonic Case Cleaning Solution (RCBS #87058). To provide a real challenge, Gavin used some very dull and greasy milsurp brass: “I bought a huge lot of military once-fired 7.52x51mm brass (fired in a machine gun) that I’ve been slowly prepping for my DPMS LR-308B AR-10 style rifle. Some of this brass was fully prepped (sized/de-primed, trimmed, case mouths chamfered, primer pockets reamed) but it was gunked up with lube and looking dingy.”
UltimateReloader.com Case Cleaning Video (7.5 minutes):
Gavin describes the cleaning exercise step-by-step on UltimateReloader.com. Read Gavin’s Cartridge Cleaning Article to learn how he mixed the solution, activated the heater, and cycled the machine for 30 minutes. As you can see in the video above, the results were impressive. If you have never cleaned brass with ultrasound before, you should definitely watch Gavin’s 7.5-minute video — it provides many useful tips and shows the cleaning operation in progress from start to finish.
Ultra Dry Necks After Ultrasonic Cleaning — Some Suggestions
The Ultrasonic cleaning process gets cartridge brass so “squeaky clean” that increased force may be required to seat your bullets, or they may “grab” as they go in the necks. To reduce bullet-seating effort, you may benefit from adding a little dry case lube inside the case-neck before loading (use a nylon brush). Another trick is adding a teaspoon of Ballistol lube to the cleaning solution. That provides a trace lubricant inside the necks, but does not interfere with powder ignition in any way.
The latest Gen2 RCBS ultrasonic cleaning machine has a large 6.3-quart capacity. That’s nearly 100 percent larger than the first generation machine in Gavin’s video. The Gen2 machine, $322.02 on Amazon, features a second ceramic heater and transducer to better clean brass cases and firearm parts. The LED is easily programmable, and the timer can be set for up to 30 minutes of cleaning. The original 3.2 quart capacity RCBS ultrasonic machine, as shown in Gavin’s video, is still available for $166.56 at Midsouth Shooters.
Similar Posts:
- How to Clean Brass Effectively with Ultrasonic Cleaning Machines
- Clean Brass Effectively with Ultrasonic Cleaning Machines
- No More Dirty Brass — How to Use Ultrasonic Cleaning Machines
- Get Brass Ultra-Clean with Ultrasonic Machines
- How to Clean Brass with an Ultrasonic Cleaning Machine
Share the post "How to Clean Cartridge Brass with Ultrasonic Cleaning Machines"
Tags: Brass, Cartridge Brass, Gavin Gear, RCBS, Tumbling, UltimateReloader, Ultrasonic, Ultrasound
Midway has the Rock Chucker Supreme for $138 on sale. It qualifies for a $25 rebate. That’s $113. That’s a good buy.
I rinse my brass and then wipe with towel then shake excess water then stack primer side down in a tray hit with a hair dryer then flip into another tray primer side up and dry until primer holes are dry shake again to knock out any more water repeat. takes practice to get the brass primer side up
I have a ultrasonic cleaning system. No longer in use, drying the cases proved to be a major pain in the neck…. I use a dry system tumbler now.
Nothing can get the brass as clean as ultrasonic. I would not use anything else.
Editor: Ultrasonic is extremely effective. However each shooter needs to identify how clean is clean enough for their purposes, and whether there are trade-offs from removing all the carbon inside the case-neck.