HOME PAGE
Shooters' FORUM
Daily BULLETIN
Guns of the Week
Articles Archive
BLOG Archive
Competition Info
Varmint Pages
6BR Info Page
6BR Improved
17 CAL Info Page
20 CAL Info Page
223 Info Page
22BR Info Page
30BR Info Page
6PPC Info Page
6XC Info Page
243 Win Info Page
6.5x47 Info Page
6.5-284 Info Page
7mm Info Page
308 Win Info Page
FREE Targets
Top Gunsmiths
Tools & Gear
Bullet Reviews
Barrels
Custom Actions
Gun Stocks
Scopes & Optics
Vendor List
Reader POLLS
Event Calendar
HELP PAGE
> Contact Us
> ADVERTISING














Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









August 31st, 2021

Monitor Targets Better with Anti-Reflective Tablet Screen Covers

Winning in the Wind icarez anti-reflective screen protector ipad tablet
Winning in the Wind icarez anti-reflective screen protector ipad tablet

If you ever shoot with electronic targets, ShotMarkers, or target cams, chances are you’ll spend lots of time looking at the screen of a tablet computer or iPad. These electronic devices are pretty amazing, but they have one major shortcoming when used outdoors — reflections from the highly-polished glass screen.

Well it turns out there is a simple, inexpensive solution to the problem of annoying tablet screen reflections. Just purchase a quality anti-reflective screen protector for your tablet, iPad, or smartphone and you will eliminate most annoying reflections and make your mobile device MUCH easier to use at the range.

Take a look at the two photos above. The first photo shows how annoying reflections can obscure the ShotMarker display on a tablet. The second shot shows how much easier it is to view the ShotMarker target image with an anti-reflective screen cover in place. BIG improvement!

Our friend Keith Glasscock recently added an anti-reflective screen protector to his iPad tablet and found that it works wonders. Keith recently reviewed the iCarez Matte Screen Protector for his Winning in the Wind YouTube Channel. These screen covers are available in a wide variety of sizes to fit most Apple iPhones and Apple iPads. These thin, matte screen protectors are quite affordable, with prices starting at just $6.95.

In addition, there are other brands of screen protectors for Android devices that work the same way. Again, you’ll find a variety of sizes. For example, Supershieldz now offers a 3-pack of matte screen covers for 10″ Samsung tablets for just $6.99 on Amazon

In the above video, Keith Glasscock explains the problem of screen reflections when using mobile devices for shot monitoring. Keith then describes his positive experience with the iCarez Matte screen cover installed on his personal iPad.

Winning in the Wind icarez anti-reflective screen protector ipad tablet

A good screen cover can eliminate this kind of harsh reflection on tablet screens:
Winning in the Wind icarez anti-reflective screen protector ipad tablet

Share the post "Monitor Targets Better with Anti-Reflective Tablet Screen Covers"

Permalink - Videos, Gear Review, Optics No Comments »
August 31st, 2021

Cartridge Cutaways — View INSIDE Loaded Ammunition

sliced cutaway ammo ammunition FOG diagram

Here’s something you don’t see every day — the inside of loaded cartridges, sliced halfway through. This lets you see how bullet core, jacket, cartridge case, powder, and primer all fit together. Give credit to the folks at FOG Ammunition for creating this interesting series of cut-through ammo images. We show four cartridges here: the .308 Winchester, 9mm Luger, 300 BLK, and .50 BMG. You’ll find two more (the .223 Remington and .45 ACP) at www.FogAmmo.com.

sliced cutaway ammo ammunition FOG diagram

This .308 Winchester model took on a different approach by only cutting the brass case and displaying the full bullet, primer and powder load. A spec amount of powder was used to create the model powder form. An estimated 10% volume was added during the forming process, along with an undetermined amount of air pockets.

sliced cutaway ammo ammunition FOG diagram

This bisection is a 9mm Luger Jacketed Hollow Point round with flake powder held together with super glue. After this self-defense round was cut by a trained professional the round was polished by hand. This might look like stick powder, but those are in fact flakes stacked up in cross-section. Designed in 1901 by Georg Luger, this popular cartridge is used by civilians, military, and law enforcement.

sliced cutaway ammo ammunition FOG diagram

For this model of the .300 AAC Blackout (aka 300 BLK), a Dremel tool was used to create a pie cut within the bullet and brass case. A measured amount of power, roughly 65% of spec charge, was placed inside the case with super glue. This cartridge was originally optimized for subsonic use with a suppressor, so the amount of powder used is small relative to the nominal case capacity. That leaves more room for the relatively large .30-caliber bullet.

sliced cutaway ammo ammunition FOG diagram

Last but definitely not least is the .50 Caliber BMG round (aka .50 Browning Machine Gun). Famed for its wartime use in the M2 Machine gun, the .50 BMG round is also used in civilian Long Range competitions. A typical .50 BMG cartridge holds over 225 grains of powder. That’s almost ten times the amount in a 5.56×45 NATO Round! To demonstrate the size of the .50 BMG, check out that .223 Rem for comparison.

Share the post "Cartridge Cutaways — View INSIDE Loaded Ammunition"

Permalink Bullets, Brass, Ammo, Gear Review, Tech Tip No Comments »
August 31st, 2021

Hydro-Form 6mm Dasher Brass — Save Money & Barrel Life

6mm Dasher hydroforming case die hornady

Can you form a wildcat cartridge such as the 6 Dasher without expending primer, powders, and bullets? Absolutely. Using the hydro-forming method you can form improved cases in your workshop with no firing whatsoever, so there is no wear on your precious barrel. Watch this video to see how it’s done:

6 Dasher Case Hydro-Forming Demonstration:

Forum member Wes J. (aka P1ZombieKiller) has produced a helpful video showing how to form Dasher cases use the Hornady Hydraulic forming die kit. This includes a two-part die (body and piston), and a special shell holder. To form the case, you insert a primer in your virgin brass, top the case off with with a fluid (water or alcohol), then run the case up into the Hydro-forming die. A few stout whacks with a hammer and your case is 95% formed.

Whidden gunworks 6 6mm dasher hydro-forming hydraulic form die

This same procedure can be accomplished with a Whidden Gunworks 6mm Dasher hydraulic form die. We like the Whidden hydro-forming die for its production quality and consistent results. This Whidden system works great according to our Forum members.

6mm Dasher hydroforming hydraulic 6mmBR hornadyHydro-Forming Procedure Step-by-Step:
1. Insert spent primer in new 6mmBR brass case.
2. Fill with water or alcohol (Wes prefers alcohol).
3. Wipe excess fluid off case.
4. Place case in special Hornady shell-holder (no primer hole).
5. Run case up into Hydraulic forming die.
6. Smack top piston of forming die 3-4 times with rubber mallet or dead-blow hammer.
7. Inspect case, re-fill and repeat if necessary.
8. Drain alcohol (or water) into container.
9. Remove primer (and save for re-use).
10. Blow-dry formed case. Inspect and measure formed case.

Wes achieves very uniform cartridge OALs with this method. He measured ten (10) hydro-formed 6 Dasher cases and got these results: two @ 1.536″; 2 @ 1.537″; and 6 @ 1.538″.

Three or Four Whacks Produces a 95%-Formed Case
With a Whidden or Hornady hydro-forming die, hydraulic pressure does the job of blowing out the shoulders of your improved case. The process is relatively simple. Place a spent primer in the bottom of a new piece of brass. Fill the case with water, and then slip it into a special Hornady shell-holder with no hole in the middle. Then you run the case up into the forming die. Now comes the fun part. You gently insert a plunger (hydraulic ram) from the top, and give it three or four stiff whacks with a mallet (or better yet, a dead-blow hammer). Remove the plunger and you have a 95% formed case, ready to load.

Walter Queen Hydraulic Hornady DieSpecial Shell-Holder
Hornady supplies a shell holder made specifically for the hydro die; there’s no hole in the bottom of it. Just insert a spent primer into the primer pocket and you’re ready to go. The spent primer, combined with the solid shell holder, keeps the water from seeping out of the primer pocket. The primer pushes out a little bit during this process, but it’s impossible for it to come out because of the way the shell holder is designed. The shell holder has a grove which allows the case to slide out of the shell holder even when the primer protrudes a bit.

Share the post "Hydro-Form 6mm Dasher Brass — Save Money & Barrel Life"

Permalink - Articles, Bullets, Brass, Ammo, Reloading, Tech Tip 3 Comments »