The question of barrel break-in is controversial. Some folks advocate an elaborate, lengthy cycle of shooting and brushing, repeated many times — one shot and clean, two shots and clean and so on. This, it is argued, helps barrels foul less and shoot more accurately. Others say minimal break-in, with patching and brushing after 10-15 rounds, is all you need. Still others contend that break-in procedures are a total waste of time and ammo — you should just load and shoot, and clean as you would normally.
We doubt if there will ever be real agreement among shooters concerning barrel break-in procedures. And one must remember that the appropriate break-in procedure might be quite different for a factory barrel vs. a custom hand-lapped barrel. This Editor has found that his very best custom barrels shot great right from the start, with no special break-in, other than wet patches at 5, 10, and 15 rounds. That said, I’ve seen some factory barrels that seemed to benefit from more elaborate break-in rituals.
What’s the best barrel break-in procedure? Well our friend Eric Mayer of Varminter.com decided to ask the experts. A while back Eric interviewed representatives of three leading barrel manufacturers: Krieger, Lothar-Walther, and Shilen. He recorded their responses on video. In order of appearance in the video, the three experts are:
Do I Need to Break-In a New Rifle Barrel?
Eric Mayer of Varminter.com says: “That is a simple question, [but it] does not necessarily have a simple answer. Instead of me repeating my own beliefs, and practices, on breaking-in a new rifle barrel, I decided to answer this one a bit differently. While we were at the 2016 SHOT Show, we tracked down three of the biggest, and most popular, custom barrel makers in the world, and asked them what they recommend to anyone buying their barrels, and why they recommend those procedures. We asked the question, and let the camera run!” Launch the video above to hear the answers — some of which may surprise you.
Long-Term Barrel Care — More Experts Offer Opinions
Apart from the debate about barrel break-in, there is the bigger question of how should you clean and maintain a barrel during its useful life. Some folks like aggressive brushing, other shooters have had success with less invasive methods, using bore foam and wet patches for the most part. Different strokes for different folks, as they say. In reality, there may not be one solution for every barrel. Different fouling problems demand different solutions. For example, solvents that work well for copper may not be the best for hard carbon (and vice-versa).
“Why worry about a little barrel fouling when the throat is subjected to a brutal 5,600° F volcano at 55,000 PSI? To investigate these and other questions about taking care of a match barrel, we spoke with a dozen experts and share their knowledge in this first of a series of articles.
After listening to folks who shoot, build barrels or manufacture cleaning solvents for a living, we concluded that even the experts each have their own unique recommendations on how to care for a match barrel. But they all agree on one thing — the gun will tell you what it likes best. Because the life expectancy of a match barrel is about 1,500 to 2,500 rounds, the objectives of cleaning one should include: preserve accuracy, slow the erosion, and remove fouling — all without damaging the gun. This article doesn’t claim that one cleaning method is better than the next. Rather, we set out to interject a little science into the discussion and to share some lessons learned from experts in the field.” — Chip Lohman
As part of NRA Women TV, hunting guide Kristy Titus hosts a series of videos that explain important strategies and shooting skills for hunters. Titus, co-host of the Team Elk TV show, is a certified instructor who has hunted around the globe. She grew up in the outdoors, running pack mules in Oregon with her father. In these videos, Kristy discusses demonstrates field positions that can be employed during a hunt. She also explains preparation for a hunt, including fitness training.
Click each link below to watch other Kristy Titus Hunting Videos.
“When it comes to bolt-action rifle fit, there is no ‘one size fits all’,” says Titus. “When picking out your rifle [consider options] after the purchase to ensure you are as comfortable as possible.”
Even wonder how a pump shotgun works? Then watch this fascinating video from MidwayUSA. The operation of a pump-action shotgun is illustrated with a special cut-away version of a Winchester Model 12. The shotgun has been modified to reveal the inner workings. This cut-away Model 12 still loads and ejects dummy shells, but you can see how the lugs, slides, locks, ramps, springs and other internal parts work. You’ll be amazed how complicated this old pump-gun is. (The Model 12, Winchester’s first hammerless shotgun, is one of the most popular scatterguns ever made. Over 2,000,000 were sold.)
Skip Ahead to 3:00 to See Cut-Away in Action
To see how the Model 12 works, you can skip forward to the 3:00 minute mark in the video. The first part of the video shows how the Model 12 was “sliced and diced” to expose the inner workings. Larry Potterfield of MidwayUSA explains that “the factories often used cut-aways as sales tools to show how a specific model operated”. In addition the U.S. Military used cut-aways for training purposes.
Here is the cut-away completed. Even the pump grip has been sliced to reveal the inner workings.
A round has been picked up from the feed tube, and then is lifted into the chamber.
Here’s a very cool 3D Animation showing pistol rounds being fired. Computer-generated graphics provide a look inside the cartridge at the moment of ignition as the primer fires and the flame front moves through the ignited powder. It’s really kind of mesmerizing. If you’ve every wondered just what happens inside your cartridges the moment that firing pin strikes, then watch this video…
Watch Video to See Handgun Ammo Being Chambered and Fired:
Mute Enabled — Click Speaker Icon to Hear Audio. Firing Sequence Starts at 1:28.
This animated video from German ammo-maker GECO (part of the Swiss RUAG group of companies) reveals the inside of a pistol cartridge, showing jacket, lead core, case, powder and primer. Employing advanced 3D rendering and computer graphics, the video shows an X-ray view of ammo being loaded in a handgun, feeding from a magazine.
Then it really gets interesting. At 1:28 – 1:50 you’ll see the firing pin strike the primer cup, the primer’s hot jet streaming through the flash-hole, and the powder igniting. Finally you can see the bullet as it moves down the barrel and spins its way to a target. This is a very nicely-produced video. If you’ve ever wondered what happens inside a cartridge when you pull the trigger, this video shows all. They say “a picture’s worth a thousand words”… well a 3D video is even better.
Chart created with Ammoguide’s Visual Comparison Tool. Visit Ammoguide.com to learn more.
One of our forum members was looking for a very accurate, mid-sized 6.5mm cartridge for target working and coyote hunting. There are many great options including the 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor, and Remington .260 (a 6.5-08). If you are considering the 6.5×47 you should read our 6.5×57 Cartridge Guide authored by the 6.5 Guys. This and other 6.5mm cartridges are covered in this introduction to 6.5 mm cartridges prepared by Eben Brown, President of Eabco.com.
Quick Guide to 6.5mm Cartridges
by Eben Brown, EABCO.com, (E. Arthur Brown Co. Inc.)
The current popularity of 6.5mm cartridges in the USA has been a long time in coming. I won’t go into my opinions on why it took so long to catch on. The important thing is that it finally HAS caught on and we’re now so fortunate to have a wide selection of 6.5mm cartridges to choose from!
6.5mm Grendel – Developed by Alexander Arms for the AR15 and military M4 family of rifles. The Grendel fits the dimensional and functional requirements of these rifles while delivering better lethality and downrange performance. [Editor: The little 6.5 Grendel delivers a lot of performance from a small package. This is one of the most accurate cartridge options for the AR15 platform.]
6.5mm BRM – Developed by E. Arthur Brown Company to give “Big Game Performance to Small Framed Rifles” — namely our Model 97D Rifle, TC Contender, and TC Encore. Velocities of 2400-2500 fps with 140gr bullets puts it just under the original 6.5×55 Swede performance.
6.5mm x 47 Lapua – Developed by Lapua specifically for international 300m shooting competitions (with some interest in long-range benchrest as well). Case capacity, body taper, shoulder angle, and small rifle primer are all features requested by top international shooters. You can expect velocities of 2500-2600+ with 140 gr bullets.
6.5mm Creedmoor – Developed by Hornady and Creedmoor Sports, the 6.5mm Creedmoor is designed for efficiency and function. Its shape reaches high velocities while maintaining standard .308 Winchester pressures and its overall length fits well with .308 Win length magazines. You can expect velocities of 2600-2700+ fps with 140gr bullets. [Editor: Yep, we know some PRS guys are loading hotter than that in bolt guns. We recommend you try the 120-130 grain bullets also with this cartridge. That may put you in a better accuracy node.]
This video reviews 6.5 Creedmoor Cartridge Brass options:
.260 Remington – Developed by Remington to compete with the 6.5mmx55 Swedish Mauser that was (finally) gaining popularity in 1996. By necking down the 7mm-08 Remington to 6.5mm (.264 cal), the .260 Remington was created. It fit the same short-action [receivers] that fit .308 Win, .243 Win, 7mm-08 Rem, etc. You can expect velocities of 2600-2700 fps with 140gr bullets in the 260 .Remington.
[Editor’s Note: In the .260 Rem, try the Lapua 120gr Scenar-Ls and/or Berger 130gr VLDs for great accuracy and impressive speeds over 2950 fps.]
6.5mm x 55 Swedish Mauser – This was the cartridge that started the 6.5mm craze in the USA. It is famous for having mild recoil, deadly lethality on even the biggest game animals, and superb accuracy potential. Original ballistics were in the 2500 fps range with 140gr bullets. Nowadays handloaders get 2600-2700+ fps.
[Editor’s Note: Tor from Scandinavia offers this bit of 6.5x55mm history: “Contrary to common belief, the 6.5×55 was not developed by Mauser, but was constructed by a joint Norwegian and Swedish military commission in 1891 and introduced as the standard military cartridge in both countries in 1894. Sweden chose to use the cartridge in a Mauser-based rifle, while Norway used the cartridge in the Krag rifles. This led to two different cartridges the 6.5×55 Krag and 6.5×55 Mauser — the only real difference being safe operating pressure.”]
6.5-284 Norma — This comes from necking the .284 Winchester down to .264 caliber. Norma standardized it for commercial ammo sales. The 6.5mm-284 was very popular for F-Class competition and High Power at 1,000 yards. However, many F-Class competitors have switched to the straight .284 Win for improved barrel life. 6.5-284 velocities run 3000-3100+ fps with 140gr bullets.
.264 Winchester Magnum – Developed by Winchester back in 1959, the .264 Win Mag never really caught on and may have delayed the ultimate acceptance of 6.5mm cartridges by US shooters (in my opinion). It missed the whole point and original advantage of 6.5 mm cartridges.
The Original 6.5mm Advantage
The special needs of long-range competition have skewed things a little. However the original advantages of 6.5mm cartridges — how deadly the 6.5mms are on game animals, how little recoil they produce, and how easy they are to shoot well — still hold true today.
The NRA’s American Rifleman showcased an interesting project this week — an upgraded Ruger American Rifle Predator in 6.5 Creedmoor. The video below shows how a laminated wood stock from Boyds Gunstocks was adapted for the Ruger. A Boyds Prairie Hunter model in gray laminate was selected. This was custom-bedded to the Ruger’s action using Brownell’s Acraglas.
All Ruger American Rifle models employ dual aluminum V-Blocks to support the action. These fit slots in the underside of the action. Boyds makes its own version of these V-Blocks which were installed in the Boyds stock to secure the action.
Project leader Joe Kurtenbach says the size, shape, and geometry of the Boyds V-Blocks is very accurate, so they fit the Ruger action well. To further support the action, Acraglas bedding compound was applied to the inside of the stock, after release compound was applied to the barreled action. With this DIY bedding job, the Boyds laminated stock is definitely an improvement over this original “Tupperware” factory stock.
DIY Bargain Hunter Upgrade
American Rifleman states: “The Ruger American has some great features—hammer-forged barrel, reliable action, crisp trigger — but many would not consider the molded, polymer stock to be among them. Luckily, there are aftermarket options to enhance the rifle’s utility and aesthetics. A durable, attractive stock from Boyds Gunstocks and some DIY action bedding, using Brownells Acraglas, is the next step in the precision-driven hunting rifle build.”
Choice of Gun and 6.5 Creedmoor Chambering
For this project, American Rifleman’s Joe Kurtenbach selected one of his favorite cartridges, the 6.5 Creedmoor. Introduced in 2007 by Hornady, the accurate, flat-shooting 6.5 Creedmoor has proven very popular with both hunters and tactical/PRS shooters. The Ruger American Rifle Predator was chosen for its affordable price, reliable action, and Ruger Marksman adjustable trigger.
In this video, Kurtenback explains how and why the 6.5 Creedmoor chambering and Ruger American Rifle were chosen for the Precision Hunter rifle build project.
GRS stocks are produced in Norway. These stocks are known for their comfortable fit and ergonomics, but they are also strong and durable — thanks to attention to detail, careful construction, and premium materials. While GRS Riflestocks AS now produces excellent composite stocks, the majority of its products are still crafted from laminated wood. That’s not surprising because the GRS stock business evolved from a family furniture company.
This excellent video shows every stage of GRS Stock production. Worth Watching — Honest! Sawing Blanks: 0:15 | CNC Milling 0:20 | Surface Sanding 0:30 | Dip Finishing 1:00
Making a GRS Laminated Stock
GRS stocks start off with blocks of laminated wood. There are potentially 1700 combinations given the number of colors, models, and inlets. The first stage employs a band saw to shape the rough outer shape and dimensions. Then each stock goes into a computer-controlled CNC machine for precision milling. From the CNC-machine, the rifle stock is handed over to GRS craftsmen who hand-finish the stock (photo below). Depending on design, GRS stocks can be delivered with up to 40 different inlets.
GRS Stocks — Ergonomically Designed Good ergonomics have always been a key GRS design objective: “All our rifle stocks are adjustable, because people are different. If you make a fixed stock, it will always be a compromise for your shooting position. Also, your ergonomics change in different shooting positions. There is a big difference between standing, sitting and laying on the ground. It’s not rocket science, but we recognized this a long time ago. And that is why we made the adjustment system the way it is. Obviously, having the correct length of pull, and a full contact with the cheek-piece, adds a lot of stability into the shooting position.”
When you handle a GRS stock, and get into shooting position, you notice it feels comfortable immediately. And the LOP and cheek-piece height can be adjusted easily, without tools.
The GRS grip design is distinctive — for important reasons: “The grips that we have (which off-centered and angled out) remove tension in your arms. So when you shoot you are more relaxed. And the recoil transfers neatly in your body.”
About GRS Riflestocks AS — A Family Company Run by Serious Shooters
GRS Riflestocks AS is run by two brothers, Håvard and Oscar Haugen. Oscar served in the Norwegian military for a decade as a QRF Sharpshooter (sniper) and Sharpshooter Team Leader. Oscar’s military experience has helped GRS design better rifle stocks: “I was a Sharpshooter for the Norwegian army for a long time, both as a soldier and instructor. So we knew what worked in the field. And we knew production. So we took something traditional, as a rifle stock is, and introduced something new into it. This way, the ergonomics and the adjustment systems became key features of the GRS rifle stocks.”
Håvard Haugen (L) and Oscar Haugen (R), founders of GRS Riflestocks AS.
GRS Riflestocks AS has become very successful. The company now ships stocks to 45 countries worldwide. Oscar Haugen says: “I smile every day knowing more and more hunters and shooters gets to know GRS. We make them shoot more accurately because their rifles fit them better [with our stocks]. What more could we ask for?”
GRS Stocks are produced in Hornindal, Norway. Watch the video to see beautiful Norwegian scenery: “A short walk from the factory, you’re in the woods. You can go fishing, hunting … whatever you like”.
Do you neck-turn hundreds of cases annually? Then you deserve this outstanding tool. This innovative neck-turning system is truly a game-changer. The 21st Century Shooting Powered Neck-Turning Lathe is quite simply the best system ever created for quickly and precisely uniforming (and reducing) the neckwall thickness of cartridge brass. We have the original manual 21st Century neck-turning lathe, and can attest that it works great. But with the new powered system you can turn necks faster and more efficiently, with less effort. This is like going from a stick shift to an automatic transmission. The cases feed very smoothly and the results are beautiful. Once you’ve tried the Powered Neck-Turning Lathe you won’t want to use anything else. Watch this video to see how it works:
Power is activated by the red button on the end of the blue, horizontal feed handle:
Click the Speaker Button on video frame to play with sound (audio).
The Powered Neck-Turning lathe is a modular system. Swing the bar from right to left to feed the case. The power head (with case holder) glides on stainless steel rails for smooth movement. This allows very precise feed rate. Power is supplied via a button that is built into the end of the feed handle. Push the red button to make the case spin. It’s as simple as that.
The folks at 21st Century Shooting explain why the system works so well: “The floating design of our Neck Turner and Case Driver allows the case mouth (bore) to run on the arbor absolutely concentric. This, therefore, allows the outside diameter to be turned concentric with the inside diameter.”
Here is another video that shows how the lathe system operates:
Click the Speaker Button on video frame to play with sound (audio).
Complete Powered Neck-Turning Lathe System
The powered neck-turning system comes with everything you need, starting at $679.00. This includes: Motor Assembly, Lathe Base, “L” bracket, Neck-Turning Tool, Cutter, Case Holder, Driver, Turning Arbor, Expander Die Body, and Expander Mandrel. 21st Century currently offers a choice of nine popular calibers: .17, .20, .22, .243 (6mm), .264 (6.5mm), .270, .284 (7mm), .30, and .33. The case holders are appropriately sized for the common rim sizes in that caliber. Choose either stainless arbor and mandrel or Titanium Nitride-coated arbor and mandrel (for $20 more). Some of the larger calibers cost a bit more.
Report By Boyd Allen, IBS Vice President Huge credit to Ken Frehm for all of the photos and most of the information.
On July 14th and 15th, at the Camillus Sportsmen’s Club, Camillus, NY, thirty-two shooters vied to win the Two Gun (and Class titles) at the NY State IBS Championship & 19th Annual Pro-Am Group Shoot. The Pro-Am is a cash match. Twenty-five of thirty-two shooters participated in the cash option — five dollars per gun per day. They were the Professionals. The remaining seven were the Amateurs.
The weather was balmy and mild, the prize table and cash awards were generous, and the new range improvements were extensive, expensive, and well executed. Overall temperatures were seasonally moderate and the wind, while not difficult, was challenging enough that there were no Teen Aggregates shot in any class.
IBS Competitors Talk about their Sport
Definitely check out this video — it is excellent, and well worth your time. It shows the Camillus Club Range and features informative interviews with many shooters:
The Two-Gun Overall match winner was Bob Brushingham, with Don Francis in second place, and Bob White in third. Don, who finished with a .2600 Grand Agg, edged Bob (.2601) by a mere .0001! That’s close! (SEE Full Two-Gun Results).
Two Gun top finishers (L to R): Bob White (3rd), Bob Brushingham (1st), Don Francis (2nd)
Click image for large version.
Below are the LV and HV Class winners, Class Top Ten results, and respective equipment lists.
Light Varmint top finishers were (above, L to R): Bob Brushingham (2nd LV 100), Henry Miller (1st LV 200), Don Francis (1st LV 100, 3rd LV Grand), Leonard Burdick (2nd LV 200, 2nd LV Grand), Don Jeffers (3rd LV 100, 1st LV Grand).
Click image for large version.
Heavy Varmint top finishers were (above, L to R): Bruce Lachapelle (1st HV 100), Robert Blanchard (3rd HV 100), Bob Brushingham (2nd HV 200, 1st HV Grand), Don Francis (2nd HV 200), Ron Burdick (2nd HV 100, 3rd HV Grand), and Bob White ( 1st HV 100, 2nd HV Grand).
Click image for large version.
Here is the winning Pro-Am Team: Jennaro (Jerry) Corigliano (1st Amateur), Bruce Lachapello (1st Pro).
IBS 100/200-Yard Benchrest Competition
As with all Registered IBS 100/200-yard Group Matches, the N.Y. Championships at Camillus employed moving backers. This system ensures that a completed group includes the requisite five shots. With extremely small groups in the “ones” and “zeros” it may be impossible to distinguish five holes.
Although pre-loading is not uncommon, most 100/200-yard group shooters typically load at the match, often between relays. This enables them to tune their loads for the current conditions. Nearly all competitors in this short-range discipline shoot the 6mm PPC cartridge, or a PPC variant.
With group sizes so small, and group dimensions listed to the thousandth of an inch, precise measurement is an important part of the process.
The Camillus Sportsmen’s Club Range
This is not just a benchrest club, but a complete, multi-discipline shooting sports facility. To my California eyes, the Camillus range is a thing of beauty, with a vast expanse of well-trimmed grass between the firing line and the berms, and a substantial wooded hill beyond. The club has just completed a host of brand new improvements that required a significant investment and, I am sure, a lot of hard work. I believe that this was the first time that an event was held after they were finished. The improvements include a new shooting pavilion (firing line cover), with the latest safety features, new all masonry benches, new berms, new target boards, and may others that are too numerous to mention.
Backing up the range berm is a 120-foot high wooded hill. Behind the firing line, running northwest along the club’s western boundary, is the old, abandoned Erie Canal. The Club’s land is relatively flat, which has allowed it to be well-utilized for multiple shooting sports. See Google Map.
Parting Shot… I had to smile at this picture of the target crew. Evidently the club has excellent relations with the Syracuse Police Department.
Shooting USA will broadcast a great episode today, August 1, 2018. There are three segments worth watching. First the TV show spotlights the popular GAP Grind, a Pro-Am PRS event at the K&M Precision complex in Tennessee. Then this episode covers the CMP Western Games at Ben Avery in Phoenix. Finally John Scoutten reviews two new 6.5 Creedmoor Savage rifles.
This Shooting USA Episode airs August 1, 2018 (Wednesday) at 9:00 Eastern and Pacific; 8:00 Central.
Part One: GAP Grind Pro-Am PRS Match
Lots of Action, with 20+ Stages
The GAP Grind, the biggest PRS match in the country, is a notoriously challenging, “high tempo” match with minimal down-time between stages. Over the course of 20+ stages, competitors will fire 200+ shots at a variety of steel, paper, moving, and reactive targets out to 1,200 yards. Targets vary in size/difficulty based on the shooter’s position, distance, and time allotted. Most stages include “stressors” — i.e. time limits or required movement(s).
The GAP Grind attracts over 300 competitors — half experienced shooters and the other half newcomers to the sport. The key to growing the shooting sports is attracting new shooters. The best way to bring in “new blood” seems to be the Pro-Am type format. At the GAP Grind, experienced shooters guide the new shooters through the competition and hopefully keep them coming back.
Here is Shooting USA Host John Scoutten (in Blue/White shirt)
John Scoutten is paired with new shooter Kevin Nassery who says he thinks the biggest advantage is not necessarily the course of fire, or the targets, it’s the spotting. “Pros don’t get any support to know where they hit or missed. They have to see everything themselves. I think that’s the biggest difference between the courses of fire”.
Part Two: CMP Western Games
The Civilian Marksmanship Program (CMP) was established by act of Congress in 1903, with the purpose of teaching shooting skills to American citizens. The Western Games at the Ben Avery Facility North of Phoenix draws enthusiasts from many Western states for competition with Service Rifles, vintage military rifles, M1 Carbines, and Rimfire Sporter rifles. Along with numerous matches (including the Vintage Sniper Team match), the Western Games features Small Arms Firing School (SAFS) shooting clinics.
“Our mission is to teach marksmanship and give the citizens of the United States the opportunity to learn marksmanship, with an emphasis on youth”, states Mark Johnson, CMP Chief Operating Officer.
Vintage Sniper Rifle Match competitors try to keep cool
A Small Arms Firing School (SAFS) is conducted each year.
Checking out the line-up of M1 Garands at the CMP Sales tent.
The CMP’s rifle and ammo sales programs fund the CMP activities. The M1 Garand has been the CMP’s most popular centerfire rifle over the years. Mark Johnson calls it “the ’57 Chevy of firearms. If you like firearms, you have to have an M1 Garand.”
Part Three: Savage 6.5 Creedmoor Rifles Review
In this review segment of today’s Shooting USA episode, John Scoutten reviews two new 6.5 Creedmoor rifles from Savage Arms. The Model 10 BA Stealth is a short action bolt gun priced at $1,207 MSRP. The MSR 10 Long Range is am AR-platform semi-auto priced at $2,284 MSRP. Both rifles showed good accuracy with factory ammunition. For this test both Savage rifles were topped with Bushnell Elite LRTS optics.
Do I Need to Break-In a New Rifle Barrel?
This animated video from German ammo-maker 
.260 Remington – Developed by Remington to compete with the 6.5mmx55 Swedish Mauser that was (finally) gaining popularity in 1996. By necking down the 7mm-08 Remington to 6.5mm (.264 cal), the .260 Remington was created. It fit the same short-action [receivers] that fit .308 Win, .243 Win, 7mm-08 Rem, etc. You can expect velocities of 2600-2700 fps with 140gr bullets in the 260 .Remington.
All Ruger American Rifle models employ dual aluminum V-Blocks to support the action. These fit slots in the underside of the action. Boyds makes its own version of these V-Blocks which were installed in the Boyds stock to secure the action.
Good ergonomics have always been a key GRS design objective: “All our rifle stocks are adjustable, because people are different. If you make a fixed stock, it will always be a compromise for your shooting position. Also, your ergonomics change in different shooting positions. There is a big difference between standing, sitting and laying on the ground. It’s not rocket science, but we recognized this a long time ago. And that is why we made the adjustment system the way it is. Obviously, having the correct length of pull, and a full contact with the cheek-piece, adds a lot of stability into the shooting position.”
This is not just a benchrest club, but a complete, multi-discipline shooting sports facility. To my California eyes, the Camillus range is a thing of beauty, with a vast expanse of well-trimmed grass between the firing line and the berms, and a substantial wooded hill beyond. The club has just completed a host of brand new improvements that required a significant investment and, I am sure, a lot of hard work. I believe that this was the first time that an event was held after they were finished. The improvements include a new shooting pavilion (firing line cover), with the latest safety features, new all masonry benches, new berms, new target boards, and may others that are too numerous to mention.
The Civilian Marksmanship Program (CMP) was established by act of Congress in 1903, with the purpose of teaching shooting skills to American citizens. The Western Games at the Ben Avery Facility North of Phoenix draws enthusiasts from many Western states for competition with Service Rifles, vintage military rifles, M1 Carbines, and Rimfire Sporter rifles. Along with numerous matches (including the Vintage Sniper Team match), the Western Games features Small Arms Firing School (SAFS) shooting clinics.
In this review segment of today’s Shooting USA episode, John Scoutten reviews two new 6.5 Creedmoor rifles from Savage Arms. The 
