Editor’s NOTE: Though the product has some shortcomings, we wanted to show you guys the Hyskore Bench Beast Coaxial Competition Rest because it has some interesting engineering features (such as the scissors-jack primary elevator). The front bag holder won’t accept very wide fore-ends, and the high sides of the rear rest compromise your ability to get in close to the gun and work the rear controls while aiming. Still, there are few integrated front/rear rests on the market, so we thought you’d want to see this new offering from Hyskore.
At SHOT Show 2012, Hyskore unveiled an combined front/rear mechanical rest system appropriately named the Bench Beast. The front rest has a coaxial-type control activated by a long, angled joystick. Hyskore claims the joystick control provides 110 MOA adjustment for both windage and elevation.
For gross elevation changes, this contraption uses a scissors-jack type lift in the front that is definitely industrial in origin. In fact, the Bench Beast looks like something made in a Latvian tractor factory. But this may be useful for someone who wants a linked front and rear mechanical rest that can support a very heavy rifle (50 lbs. or more). It looks like the max width in the front is limited to 3″ so this would not work with a super-wide stock without modification. Too bad. Moreover, the front bag supplied with the Bench Beast is designed for narrow, hunter-style fore-ends. Even to run a 3″-wide gun, you’ll need to purchase an aftermarket bag. While Hyskore calls this a “competition rest”, the Bench Beast is not really set up for competition rifles.
About $500.00 for Combined Front and Rear Rests
The front and rear units can be purchased separately. Exact pricing is not yet set, but the front section should cost about $300, with the rear priced about $200.00. People should note, however, that, if you have full windage and elevation adjustment in the rear, you really only need gross height control in the front (to get on target). With a good rear rest, all the fine windage and elevation adjustment can be done from the rear, and, because of the geometry, a little bit goes a long way. It would be interesting to combine the Bench Beast’s rear unit with a simple (non-joystick) front pedestal rest.
Design Concerns
We’re intrigued with the Bench Beast’s rear unit, since there are few mass-produced, mechanical rear rests on the market. However, we have some concerns about the footprint, height, and overall size of the rear unit (SEE video 1:00-1:10). Ideally, a rear mechanical rest should allow the shooter to tuck in comfortably beside the gun. The Bench Beast has fat control knobs and tall support shafts placed far out from the centerline, on the extreme edges of the rear base.
While the wide rear base provides a solid platform, the outboard support columns and control knobs, we believe, make it difficult for the shooter to position his upper body close to the gun.
The main rear rest control knobs are also not conveniently placed. Look at the video carefully. Better rear rests have the controls further forward and closer to the centerline where they can be easily reached by the shooter’s non-trigger-pulling hand, in a comfortable shooting position. That way a right-handed shooter can easily use his left hand to work the controls while viewing the target through the scope, and holding the rifle grip with his right hand. We like the idea of an affordable rear mechanical rest, but we think the rear section of the Bench Beast would benefit from a major redesign.
Before the largest crowd ever to watch a 3-gun match, and with the largest payday in the history of the sport on the line, on the evening of January 18th, eight of the country’s top 3-gunners stepped to the firing line at the Clark County Range outside Las Vegas. With the famous Las Vegas strip illuminating the desert sky as the backdrop, the sport of 3-Gun formally announced its arrival to the shooting industry, major media outlets and a national television audience.
Photo by Tim Walsh www.seanchaicom.com
Team FNH USA’s Tommy Thacker defeated teammate Mark Hanish in the final round of the 3-Gun Nation Championship Finale, sponsored by Brownells, to become the 2012 3-Gun Nation Champion, winning an unprecedented $50,000 from Leupold Tactical Optics and NBC Sports Network.
“Unbelievable,” Thacker said, trying to put the enormity of the moment into words. “The only thing I could think is I am so blessed and everything happens for a reason. The only thing I could think is to thank God. When you think about everything that happened, I don’t know how else to describe it. Coming into this, I knew everything was right. I was in the zone more than I’ve ever been, and after the first run, I knew I was going to win this thing.”
For finishing second, Hanish was awarded a Barrett MRAD rifle fitted with a Leupold scope and BORS system, along with a check for $2,500 from Brownells.
Counting prizes awarded to other finals competitors, the Las Vegas payouts totaled $67,500, with an additional $15,000 in product value. In all, 3-Gun Nation paid out more than $150,000 in cash prizes on the 2011-2012 3GN Tour.
Champion’s Profile: Tommy Thacker is Director of Product Management for Law Enforcement & Commercial Sales with FNH USA. He is also a nationally-ranked competitive shooter, certified firearms instructor, and small business owner. He served as the inaugural Captain of FNH USA’s award winning shooting team.
The 3GN Championship Finale, sponsored by Brownells and sanctioned by NRA Sports, was the culminating event of the 2011-2012 FNH USA 3-Gun Nation Tour, Presented by SureFire. Spanning ten major 3-gun events all across the country, more than 1,500 competitors earned scores toward the 3GN Standings. From there, the top 50 competitors qualified to the 3-Gun Nation Championship in November, a one-day Tactical Optics-only match that comprised the deepest field of 3-gun talent ever assembled. The top 16 shooters then battled in an elimination Shoot-Off, with the Final 8 advancing to the Las Vegas Rumble On the Range.
Crosman unveiled a great new product at SHOT Show — a dedicated upper that transforms your AR-platform gun into a .177-caliber air rifle. Smart idea. Crosman deserves praise — we wish this was on the market decades ago. This is great for service rifle shooters who can now practice at a fraction of the cost of centerfire ammunition. Since the lower is unchanged, and the sights are the same as on a service rifle, the shooter doesn’t have to adapt to a different trigger or sight height/radius.
As Crosman representative Mark Deboard explains: “With the [MAR 177 upper kit], you can take off your AR’s centerfire upper, replace it with the Crosman upper and go to your basement or garage to shoot .177 pellets. You’re getting great trigger time without going to the range and without buying .223 ammo. You can buy a tin of 500 pellets for about five bucks.” (With a good pellet trap you could practice in your basement — but first consult your state and municipal regulations).
The 7.4-lb Crosman MAR177 Conversion Kit replaces your existing AR/M4 style upper and converts it into a PCP .177-caliber competition air rifle with 21″ free floating Lothar Walther™ barrel. Designed to support 10-meter match air rifle competition, the MAR177 is also suited for service rifle shooters who want to practice indoors in winter. Fitted with a 10-shot rotary magazine, all the shooter has to do work the bolt back every time after firing. The air reservoir offers up to 120 shots per fill.
It looks like the Crosman MAR177 will be popular. Crosman’s Deboard noted that: “We took the MAR177 to Camp Perry last summer for the High Power Rifle Championships, shot it inside the 20 foot Crosman Trailer and everyone loved it.”
Price and Availability
The MAR177 starts shipping 1/25/2012. It is available initially at crosman.com, creedmoorsports.com, and pilkguns.com. Look for retail price around $700, though Creedmoor Sports has a pre-order price of $600.
At SHOT Show, Creedmoor Sports’ General Manager, Dennis DeMille, spotted something that he thought would be a big hit with his customers — new builds of Springfield 1903-A3s and 1903-A4s using Remington or Smith Corona receivers with parkerized finishes. These rifles are built by Curt Wolfe at Rockridge Machine Works in Pennsylvania. DeMille learned about these rifles from Hornady’s Dave Emary, who gave Curt’s work at Rock Ridge a strong endorsement.
Dennis reports: “These rifles are NICE! Issue condition nice. Much nicer than the one I set a National Record with.” The A4s feature original Remington actions with turned-down GI bolt, fitted to new 30-06 4 groove, 1:10″ twist barrels chambered in .30-06. All fire-control parts are original GI. The A4s come with walnut-stained reproduction “C” stock, Malcolm reproduction of original Weaver 330C (M73B1) scope, original GI buttplate, and repro GI military leather sling. The A3s have original Smith Corona M1903 actions, click-adjustable iron sights, and will be available in both “Scant C” stocks and straight stocks. NOTE: Both the A3s and A4s use intact receivers, NOT re-welded decommissioned versions.
1903s Should Be Avaialble in Mid-February
Vintage military rifle shooters should find these rifles affordable. Dennis says: “We’ll be selling the A4s for $1,075.00, while the A3s will sell for $875.00. We should have some of all models in stock within a few weeks.” CLICK HERE for more info on Creedmoor’s new 1903-A3 or 1903-A4 rifles. Creedmoor Sports expects its first shipment from Rockridge in mid-February.
At SHOT Show 2012 we met with Andreas Krüger, managing director of Kruger Premium Targets, a family-owned business that has printed high-grade targets for over 40 years. Andreas takes great pride in the quality of his company’s targets. Andreas explained: “My family’s name is on every target we sell, therefore we want the quality to be the very best”. Kruger is the official target supplier for the International Shooting Federation, and FITA, the International Archery Federation. And now Kruger is producing official NRA targets for American shooters.
Shooting competitions are often won or lost by fractions of a centimeter in shot placement. Accordingly, it is important to use high-grade targets that provide sharp-edged bullet holes that can be measured with great precision. We are fortunate that Kruger produces official NRA targets for a wide variety of shooting disciplines — air pistol, air rifle, smallbore pistol, smallbore rifle, and centerfire competitions. These targets can be purchased through Kruger-US-Targets.com.
Kruger uses the best paper stock, and operates state-of-the-art printing machines, including one automated printing press that cost over two million Euros. The high quality of Kruger’s 210-gram board made from short-fiber raw materials, ensures that shot-holes have clean, well-defined edges. This makes a big difference, particularly with the low-velocity pellets used in airgun competition.
Eleven-Time NRA National High Power Champion David Tubb knows a bit about long-range shooting. One of the key factors in long-range accuracy is making sure that the tilt/cant of your rifle does not change throughout your shot string. In the clip below, the first in McMillan’s Master Class Video series, David Tubb explains the importance of keeping your rifle level. He explains that, at 1000 yards, your Point of Impact can change dramatically by canting the rifle either right or left. David states that, when shooting at 1000 yards, if your rifle is level and your shot is centered-up on a 72″ (six-foot) square target, you can actually put your next shot OFF PAPER by canting your rifle. That means you can move Point of Impact (POI) three feet or more, just by canting your rifle! Bryan Litz confirms Tubb’s observation. Bryan tells us that, as a general rule of thumb (for common cartridges), a 1° cant will produce five (5) inches of lateral displacement at 1000 yards. Thus, if you cant your rifle just 8°, the POI would move 40″ from the center of the target, putting the shot off the edge of a 72″-wide target.
David explains that, after one of his students has made two or three 1000-yard, X-Ring hits with a LEVEL rifle, “then I’ll have him take his rifle, and cant it to the right. I’ll have him shoot a shot. He will MISS the six-foot-square frame off to the right. Then I’ll have him cant his gun to the left and shoot another shot. He will miss the six-foot-square frame to the left.”
Rifle Hold and Canting — Consistency Counts Remember that you must maintain the exact same amount of rifle cant from shot to shot. Yes, some iron sights shooters do tilt their rifle slightly to achieve a better hold or to index their sights better. However, these shooters do not change the tilt from shot to shot — the amount of cant remains the same on every shot.
When shooting prone with a scoped rifle it’s probably best to keep the rifle dead level, with the scope’s vertical crosshair straight up and down. Use a rifle-mounted bubble level to maintain a level hold, and avoid canting the gun either to the left or to the right. Affordable bubble levels that mount to your scope or scope rail can be purchased from Brownells and other vendors, starting at about $15.00.
Rule 2.11:
Sets residency and “paid-up” membership requirements for Club Team shooters. Different standards for (a) Local Club Teams; and (b) Open Club Teams.
Rule 3.3.2 NRA Any Sight Match Rifle/Tactical Rifle
Part (c) now reads: “Competitors may use a service rifle equipped with optic sights to compete under this rule. Competitors using service rifles described in Rules 3.1(c) and 3.1(d) may remove the carry handle to allow mounting of the optic sight.”
Rule 7.22 F-Class Long Range National Championships
This section now reads:
“Any match sponsor that wishes to conduct the F-Class Long Range National Championships shall use the following courses of fire:
Day 1, 3-15 shot 1,000 yard individual matches.
Day 2, 3-15 shot 1,000 yard individual matches.
Day 3, 2, 4-person team matches, 20 shots per individual plus the aggregate of the 2 team matches.
Day 4, 2-20 shot 1,000 yard matches.”
Rule 14.18 Signal Systems for Scoring Targets
The Visual Signaling System described below will be used in all high power rifle tournaments:
(a) Slow Fire: Value spotters are placed as indicated on the target frame, all of a highly visible color such as fluorescent orange or black. The shooter may request the color they can best see.
X ………………………….……Center Right side
10 ……………………………..Bottom right corner
9 ………………………………..Bottom center
8 ……………………….……….Bottom left corner
7 ………………….…………….Center left side
6……………….……… Center right side (same as X)
5 ……………..…….Bottom right corner (same as 10)
Miss ……………….Both bottom Left corner
……………………..and bottom Right corner
The 3-Gun Nation Championship is the culmination of a 10-event series involving nearly 2,000 match competitors across the country. The Championship finale will be held at night, under the lights, in front of an invitation-only SHOT Show crowd in Las Vegas on Wednesday, Jan. 18, at 7 pm at the Clark County Range. The 3-Gun Nation elimination series began in November, with a field of 64 competitors. The top eight were selected to compete in the Championship match.
Winner Earns $50,000 — Courtesy Leupold and NBC Sports
Leupold has made sure the 2012 3-Gun Nation Championship finale features one of the largest payoffs in shooting history. The Oregon-based optics manufacturer has put up a $25,000 first-place prize. A matching offer from TV host NBC Sports brings the winner’s check to an unprecedented $50,000.
Man-on-Man Competition in Finals
The eight finalists will compete in a man-on-man shoot-off using rifles, shotguns and handguns. The first competitor to knock down all the steel targets, including the final stop plate, wins the match. Watch the Video below to see last year’s 3-Gun Nation Finale from Las Vegas:
The 3-Gun Nation Tour is the only point series and qualification standard-setting body in the sport of 3-gun and is sanctioned by the National Rifle Association. 3-Gun Nation matches can be seen on the new home of Versus, NBC Sports Network.
This Report was submitted by Darrell Buell, F-T/R Team USA Captain
The F-Class World Championships are just over a year and a half away. In the past four years, much has changed in the F-T/R game. Most noticeably, participation has increased greatly. We had 60 shooters at the 2011 Nationals in Lodi compared to 19 shooters in 2007. The level of competition has risen as well. There was a mere 3% spread in scores for the top 30 places this year. That’s tighter than it has ever been since I started keeping statistics. The top 15 spots had only a 2% score spread!
F-T/R Team USA Selection Process
With many more shooters and a higher level of competition, selecting the 2013 American F-T/R team was especially difficult. There were many qualified applicants to choose from. The selection criteria have not changed over the years. All of the 40+ applicants’ qualifications were dumped into a matrix to get sorted. The initial sort was done by examining the best data I have that compares all of the shooters side by side, i.e. Nationals scores. More weight was given to those times when I could compare shooter vs. shooter on the same relay, when they were facing the exact same conditions. From there, we used modifiers for International Team experience, and other factors. 50 million calculations later, a ranking was developed. This ranking was used to set the Roster List below.
USA F-T/R Team Roster:
Team Staff:
Captain: Darrell Buell
Vice Captain: Mike Miller
Head Coach: Mid Tompkins
Coach: Steve Cunico
Adjutant: Kathy Buell
Team Members:
Jeff Rorer
John Hayhurst
John Chilton
Chris Ozolins
John Weil
Dale Carpenter
Derek Rodgers
Team Members (cont’d):
Philip Kelley
Warren Dean
Brad Sauve
Paul Phillips
Monte Milanuk
Lane Buxton
Sierra Scott
As with past Teams, this roster will be used for the next four (4) years for International Competitions of every description. These events include (but are not limited to): 2013 F-Class World Championships in Raton, NM; 2013 South African International Matches in Bloemfontein; 2013 Stars & Stripes Challenge 2013; Creedmoor Cup; USA vs. Europe, and others.
Reserve Team Spots
The sharp-eyed will notice that I may seem to be a couple of shooters short. I am reserving a couple of spots to be named after the 2012 Nationals in Raton, in case other shooters are absolutely on fire this year, and would be good additions to the Team.
F-T/R Team USA Sponsors
As with past Team campaigns, the financial challenges (especially for the travel) will be considerable. I am absolutely committed to taking the very best Team I can field, regardless of finances. To this end, some outstanding sponsors are helping take some of the burden off the individuals: Berger Bullets, Nightforce Optics, Surgeon Rifles, Hodgdon Powder, Lapua, Kowa, and Redding Reloading. Many thanks to these and other sponsors for their continuing support.
Currently, the NRA Blog is featuring “Top Stories of 2011″. Among these stories is an account of how Carl Bernosky earned his NINTH High Power National Championship. We believe Carl’s latest National Championship title, and his amazing skills with a rifle, deserve more ink. So, here, from the NRA Blog, is the story of Carl’s 2011 victory at Camp Perry.
Bernosky Gets His 9th Nat’l HP Title
This past August, Carl R. Bernosky of Ashland, Pennsylvania, shot his way to his 9th NRA National High Power Rifle Championship at the NRA National Rifle & Pistol Championhips at Camp Perry. A National Guard training facility on the shores of Lake Erie, near Port Clinton, Ohio, Camp Perry has been home to NRA’s national championships for 102 years. The matches, which take place during July and August, have become notorious for their harsh gusts of wind, sweltering heat and storms that come off the lake with little warning.
2393-160X out of 2400
This year, during the NRA High Power Rifle Championship, Bernosky posted a 2393-160x out of a possible perfect score of 2400, Bernosky took first place and won the prestigious Mumma Trophy. In addition to winning the overall high power rifle championship, Bernosky was also the NRA Match Rifle Champion. He won top honors in eight of the eighteen matches that make up the championship and placed within the top three in five others.
“It’s just a matter of getting your mind ready to shoot the shot when it’s there and just tweaking everything a little bit”, Bernosky said when I asked him how he prepares for each match. “You don’t have to be thinking about what you’re doing, it just happens.”
During his title run this year, Bernosky tied the National Record for slow fire standing from 200 yards — an extremely impressive accomplishment. The record, a 200-15x, was originally set by Gary Anderson in 1971 during the Navy Cup.
“When I shot that 200 with 15 standing, that was discipline. I didn’t shoot a bad shot”, Bernosky told me. “That was the best target I’ve ever shot, including practice”. Bernosky tied the record during the Crescent Cup, which has the same course of fire as the Navy Cup, and finally let us know that the record had been on his mind for a very long time. “Every time I shoot a standing, whether in practice or in a match, I'm thinking about that record. I always thought I could shoot that well”, Bernosky said. “It’s tough to do and it’s a great feeling to have done that”.
The record-tying match couldn’t have come at a better time. Tied for first, Bernosky was looking for a boost to have a great day of shooting and take sole possession of the lead. The Crescent Cup was the first of the final day’s three matches and Bernosky couldn’t have asked for a better boost. “When you enter the final day and you’re tied and you just stand up there and shoot a 200-15x, it doesn’t get any better than that…”, Bernosky said.
Having grabbed the lead after the excellent performance, Bernosky held on for the last two matches and won by three points — close. Congratulated by his friends and fellow competitors as he packed up, Bernosky left the firing line a champion.