Here’s an inexpensive procedure that can help you load straighter ammo, with slightly better measured concentricity (i.e. less run-out) on the case necks and bullets. Simply use a Rubber O-Ring on the underside of the die locking ring. This allows the die to self-align itself (slightly) to the case that is being sized. Without the O-Ring, if the flat surface on the top of your press is not perfectly square with the thread axis, your die can end up slightly off-angle. This happens when the bottom of the locking ring butts up tight against the top of the press. The O-Ring allows the die to float slightly, and that may, in turn, reduce the amount of run-out induced during case sizing.
Top prone shooter GSArizona, who sadly passed last year, tried this trick and said it works: “Go to your local hardware store and get a #17 O-Ring (that’s the designation at Ace Hardware, don’t know if its universal). Slip the O-Ring on the die and re-adjust the lock ring so that the O-Ring is slightly compressed when the die is at the correct height. Size and measure a few more cases. You will probably see a slight improvement in neck concentricity as the die can now float a bit as the case enters and leaves it. This isn’t going to be a dramatic improvement, but it’s a positive one.”
We want to stress that adding O-Rings to sizing dies may help some reloaders, but we don’t offer this as a panacea. Try it — if using the O-Ring reduces measured runout that’s great. If it doesn’t, you’ve only spent a few pennies to experiment.
Lee Precision makes die lock rings with built-in O-Rings. Lee’s distinctive lock ring design allows the same kind of self-alignment, which is good. However, Lee lock rings don’t clamp in place on the die threads, so they can move when you insert or remove the dies — and that can throw off your die setting slightly. By using an O-Ring under a conventional die lock ring (that can be locked in place), you get the advantages of the Lee design, without the risk of the lock ring moving.
Do you own an older RCBS electronic powder dispenser? If you do, take the time to watch this ChargeMaster Tuning video from 8541 Tactical. This nine-minute video demonstrates how to re-program your older ChargeMaster to “tune” the dispensing process. The video shows the exact programming procedures to follow, step-by-step. Some folks want a faster powder flow — others tune their machines for a more reliable drop (with fewer over-runs). One cheap and popular modification is to insert a 1″-long section of a McDonald’s plastic straw in the ChargeMaster’s silver dispensing tube. This works surprisingly well to smooth kernel drop and prevent “clumping” that can cause an over-charge. The McDonald’s straw MOD is demonstrated in this video, starting at the 6:22 mark.
Large-Diameter Dispensing Tube Mod
Many folks have had success with the McDonald’s straw modification demonstrated in the above video. However, some folks would like to get even better flow performance (with virtually no clumping). Forum Member Frank B. has come up with a new option using a brass hose fitting with a large outside diameter. The hose fitting (with tape wrapped around the barbed nose section) is placed inside the RCBS dispensing tube (have some kind of wrap — you don’t want metal-on-metal). Here’s how the unit looks installed:
Frank tells us: “I have found a cure for the over-throw problem. It is a simple 1/4″ barbed hose nipple. I wrapped a couple layers of tape around the barbed end for a snug fit. With this in place, I have thrown 100+ charges of Varget without a single overthrow. The ID of the barbed end needs to be approximately 3/16″ to feed a steady flow. This works because of the larger ID at the drop.”
Frank adds: “You can see in the photo that the powder is not stacking up. You can watch it drop one grain at a time. Hope this will take the aggravation out of your case charging.” For best performance with this brass fitting MOD, we recommend de-burring and smoothing out the front edge of the brass fitting over which the kernels drop.
Brass fitting mod suggested by Boyd Allen. We welcome reader submissions.
There are many products used successfully for case lubrication for case sizing. And for neck-turning a variety of lubricants are favored. The video above explains the basics of case lubrication with die wax, and spray lubricants. Below we mention three products that have proven very effective. For cases that have a close fit to your chamber via custom FL dies, Ballistol works well and is easy to apply and remove. For neck-turning, some of our Forum members have had great success with some automotive lubricants.
Three Good Lubricants You May Not Have Tried Before If you’re using a body die or a full-length sizing die, try using Ballistol (in the aerosol can) as a lube. It works GREAT without the tacky or gooey residue left by most case lubes. It will also clean off carbon residues on the neck as you lube the case. Just spray a little on a cotton patch (or your fingertips) and wipe each case before you run it up into the die. If you are using a steel neck bushing, be sure to wipe the neck as well. You can usually do a half-dozen BR-sized cases before you need to re-apply Ballistol on the patch. Ballistol is non-toxic, bio-degradeable, and will not harm your skin. It is very slippery, but can easily be removed with a rag or paper towel. Try it–you may retire your One-Shot. Ballistol can also be used to protect wood stocks.
Note, for heavy case-forming or necking up case necks, we still recommend a thicker lubricant, such as Imperial Die Wax. But for normal case sizing, after your neck has been expanded, Ballistol will do the job, and you won’t need to tumble the brass afterwards. All you need is a very thin layer of Ballistol, and this easily wipes off with a paper towel.
For Neck-Turning, Try STP Blend or Assembly Lube
For lubing the neck-turning tool mandrel while turning case necks, many folks use a blend of STP® Oil Treatment and Mobil 1 lube. Chuckw2 reports: “Try STP and Mobile 1 Synthetic oil in a 50/50 mixture. Very slick, you will need to tumble your cases after turning.” STP is a very thick lubricant, that flows and clings almost like honey. Jason reports the STP blend comes off easily in an ultra-sound bath, using a bit of detergent. At many retailers, STP is also available in a convenient 7-ounce tube, so you don’t have to buy a large bottle.
Another even cheaper option is assembly lubricant. For turning his case necks, RStreich uses assembly lube from an auto parts store. He notes: “The brand I have is reddish in color and kind of sticky like honey. It’s far better than the Imperial die wax I was using before.” There are a variety of types, both with and without moly additive, and you can select the viscosity you prefer if you sample a few brands. Be sure to clean out any lube residue from the inside of your necks when you have completed your neck-turning.
AR-platform rifles are fun and versatile, but the standard, mil-spec triggers leave much to be desired. They tend to be gritty, with creep and heavy pull weight. One of the easiest, most effective AR upgrades is a trigger group swap. An improved fire control group makes a huge difference. There are many aftermarket trigger options for the AR platform rifles. Choose single-stage or two-stage, either standard trigger assembly or unitized “drop-in” trigger, such as those made by Timney or Triggertech.
When upgraded with a precision trigger and match barrel, AR-platform rigs work great in NRA High Power competitions (Photo from NRA Blog, at Camp Perry).
Two-Stage vs. Single-Stage Triggers
Two-stage triggers have two separate movements. The first stage offers a light, spring-loaded pressure that works against the shooter’s pull until stopping at the second stage – this is called “take-up”. If there is no spring pressure, it is known as “slack”. Should the shooter continue to pull the trigger once he’s arrived at the second stage, the mechanism will operate like a single-stage trigger from there until engaging the sear and firing the gun. Some shooters prefer a two-stage trigger because it allows a mental preparation (first stage) before the final decision to “break the shot”.
Single-stage triggers feature no take-up or slack, as they begin engaging the sear as soon as the shooter begins pulling the trigger. Some competitive shooters prefer the two-stage trigger because of the feedback it provides during its first stage, while other shooters, including those using their rifle in tactical scenarios, may want the surety of a single-stage trigger, ready to engage and fire once their finger is inside the trigger guard. Regardless of preference, a good trigger will feature minimal creep and should be free of grittiness, providing a smooth, even break.
Drop-In Trigger Assembly vs. Standard Trigger Group
Once you decide between a single-stage or two-stage trigger, you can choose between standard and drop-in trigger groups. Standard trigger groups feature all the fire control group parts separated, and need to be pieced together and installed much like a mil-spec trigger, while drop-in trigger are pre-assembled and contained within a casing that simply drops in to the receiver and accepts the pins, hence the name.
After-Market Trigger Comparison
Some shooters prefer drop-in triggers due to the ease of installation, while others opt for standard groups so they can access the components individually for cleaning adjustment or replacement. If one piece of a drop-in trigger fails, you’ll need to either replace the entire unit or send it to the manufacturer for repair, whereas you may be able to simply replace the broken component of a standard trigger without needing a whole new trigger set.
Trigger Terminology — “Creep”, “Stacking”, “Overtravel”
“Creep” or “travel” is the distance the trigger moves between the end of take-up and when the trigger breaks to fire the fun. Too much creep can affect accuracy, but no creep can be unsafe, as the shooter may not be prepared to fire. “Stacking” occurs when the trigger weight actually increases during travel — this shouldn’t happen. Lastly, “overtravel” is the distance the trigger continues moving back after the gun fires.
This article is based on a longer story in the NRA Blog.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Sportsman’s WH — Savage 64 Precision Rimfire Rifle, $259.99
⏺ Great deal on good starter rifle for NRL22
Here’s a bargain-priced .22 LR rifle in a modern chassis. The semi-auto Savage 64 Precision boasts a nice chassis with M-LOK slots and ergonomic pistol grip. The heavy barrel has a threaded muzzle for easy attachment of brake or suppressor. The testers in the video said this rifle was a “fantastic trainer gun” — very reliable AND very accurate. That makes this a great starting rifle for NRL22, plus the semi-auto action allows fast follow-up shots. Get this rifle on sale now for $259.99 at Sportsman’s Warehouse.
⏺ Nice small press and LOTs of tools — great price
For people getting started in hand-loading, it’s wise to start with a kit that has most of the tools you need. The very affordable RCBS Partner Press Reloading Kit comes with Press, Powder Scale, Powder Funnel, Loading Block, Lube Tray, Neck Brushes, Dubur Tool, Load Manual and more. These Partner Presses work well for loading at the range, or use the compact Partner as a second press for depriming or bullet seating.
3. EuroOptic — 15% Off Vortex Optics
⏺ Significant savings on full line of Vortex optics
Vortex scopes are a top choice of hunters and target shooters alike. Vortex offers a superb warranty and a wide variety of optics types and zoom levels. If you’ve wanted to grab a new Vortex riflescope or spotting scope visit EuroOptic. Right now you can get 15% off the vast majority of Vortex products EuroOptic has in stock. Use CODE VTX15 to get the 15% savings.
4. CDNN Sports — HK 416 .22 LR Rimfire, $399.99
⏺ Great option for AR cross-training or rimfire gun games, save $200
If you own an AR for Service Rifle competition or 3-Gun matches, here’s a great option for inexpensive rimfire cross-training. An AR-type .22 LR rifle can also be effective in NRL22 matches. Right now you can save $134 on the HK 416 .22 LR rifle plus you get a $50 card for HK webshop products. This rifle boasts a 16.1″ barrel, retractable stock, M-LOK rail, and adjustable flip-up sights. With authentic AR dimensions and ergonomics, this is a great cross-trainer.
5. Firearms Depot — Aguila .22 LR Ammo 2000 Rds, $109.38
⏺ Amazingly low price for .22 LR Ammo for plinking and training
How’d you like decent .22 LR ammo for just 5.5 cents ($0.055) per round? This is one of the best deals we’ve seen in years. You could shoot a 100-round NRL22 match for just $5.50 in ammo cost. Heck you could pay that much for just nine major brand 6.5mm bullets (at $59.99/100 they’re 60 cents each). Act soon to get these spectacular savings.
6. MidwayUSA — Walker’s Quad Connect 26 dB NRR Bluetooth Electronic Muffs, $44.79
⏺ Comfortable with excellent 26 dB NRR plus Bluetooth connectivity
These Walker Ultimate Electronic Quad muffs have an exceptionally high 26dB noise reduction rating (NRR). Some other electronic muffs are rated at just 20 or 21 dB NRR, a huge difference. These are equipped with Bluetooth so you can receive calls and audio from your smartphone. These muffs boast FOUR Omni Directional Microphones, twin volume controls, adjustable frequency tuning, integrated voice mic, and really fast reaction time. If you want something thinner, the Walker’s NRR 23 Slim Muffs are also on sale, for just $39.99, 33% Off.
7. Amazon — Tipton Best Gun Vise, $79.59
⏺ Versatile, stable, works with all rifles, including ARs
When cleaning long guns, you need a secure, stable platform. We recommend the Tipton Best Gun Vise, now $79.59 on Amazon (#ad). This vise was designed to accommodate the widest possible array of firearms for cleaning, maintenance, or gunsmithing. This vise is easily configurable to handle bolt-action rifles, break-open shotguns, AR-15s, and handguns.
8. MidwayUSA — Wheeler AR Magwell Support Block, $19.99
⏺ Great AR holder — use with Gun Vise or bench-mounted
Here’s a cool tool for AR owners, now just $19.99 on sale. The Wheeler Delta series mag well vise block holds standard AR15 lowers with your Tipton Best Gun Vise, or can work directly mounted to a bench. The vise block has 180 degrees of rotation. There is a built-in hammer stop to protect your lower while testing triggers. NOTE: This block is designed for general maintenance only. It will NOT work for removing or installing barrels, handguards, or other accessories that require large amounts of torque.
9. Amazon — Scope Turret Magnifying Glass with Level, $12.99
Making rapid, yet precise scope turret adjustments can be challenging, especially during fast, timed stages. Most scope turrets have small, thin markings that can be tough to see (particularly with older eyes). To see your elevation turret markings better, try the Monstrum Scope Turret Magnifying Glass with Level (#ad). This simple but effective tool places a magnifier on the shooter’s side of the turret allowing easy viewing. In addition, this handy unit includes a built-in bubble level to help the shooter avoid canting his rifle.
10. Amazon — MTM R-100 Ammo Box, $17.99
⏺ Best 100-rd ammo box, securely holds cartridges nose up or nose down
For transporting ammo to the range, we like the MTM R-100 Deluxe ammo box (#ad). These durable R-100 flip-top ammo boxes provide excellent protection for your ammo. When rounds are in the nose-down position special fingers in each hole prevent bullets from hitting the bottom of the box, thereby preventing tip damage. You can also pick up a semi-transparent blue version for $17.99 at MidwayUSA. We like being able to see the cartridges inside the box.
As an Amazon affiliate, this site can earn revenues through sales commissions.
When we first ran this story a few seasons back, it proved immensely popular with our readers. In case you missed it the first time around, check out what can be done with a factory Savage 110 BA at extreme long range — 1760 yards (one mile). Shooter Mark Dalzell did a great job with the video, which features multiple camera views so you can see the shooter and the target at the same time. Enjoy!
This video by Mark Dalzell demonstrates the long-range capabilities of the Savage 110 BA chambered in .338 Lapua Magnum. Mark took his “BadAss” rig out to the southwest Nevada desert just north of Jean Dry Lakes. He placed a 2’x3′ target way, way out there — a full mile (1760 yards) away. At that range, flight time to target was 3.75 seconds! Sighting with a Nightforce 5-22x50mm NXS scope, Mark needed a few shots to get on target, but eventually made multiple hits, using 67 MOA of elevation and 2.25 MOA left windage. You can view the hits starting at 1:56 time-mark on the video. (Mark had a second camera set up closer to the target — this displays frame in frame in the video, and if you watch carefully you can see the strikes.) The ammo was HSM 250gr HPBT match with a 3.600″ COAL. The shooting was done at 8:13 in the morning, with clear conditions, very light winds. Temp was 57°, humidity 24.5, Density Altitude 3666. Video soundtrack is La Grange by ZZ Top.
PLAY BUTTON
LISTEN TO MARK TALK about One Mile Shooting:
CLICK Play Button to hear Mark Dalzell TALK about his .338 LM Savage 110 BA and how he scored hits at 1760 yards.
Good Shooting Mark. That’s darn good for a factory rifle. You also had the elevation dialed in real close before the firing started! That shows a good knowledge of your ammo’s long-range ballistics. We also noticed how effective that muzzle brake was. Recoil looked about the same as an un-braked .308 Win.
.338 Lapua Magnum Cartridge Diagram
If you thought Mark’s 1760-yard shooting was impressive, Mark has produced another video that shows a session at even greater distances — out to 2300 yards. Watch Mark Dalzell Shoot at 2300 Yards.
Most folks would be very impressed with a centerfire rifle that can shoot a quarter-inch group at 100 yards. But to do that with a rimfire rifle, shooting little .22 LR cartridges, that’s quite an accomplishment. Today’s Sunday GunDay story spotlights a superbly accurate new .22 LR Benchrest gun belonging to Forum member Dave Way. This rimfire tack-driver was crafted by respected gunsmith Alex Wheeler of Wheeler Accuracy. Check out this five-shot group Dave shot once he had figured out his optimal tuner position. That is mighty impressive for a rimfire rifle!
A sub-quarter-MOA group at 100 yards is impressive for a centerfire rifle. But for a rimfire rifle, it is truly stunning. Check it out — this rifle hammers!
I tested three lots of Lapua Super Long Range today. This lot looked really good so I bought a case. It’s a blast shooting this rifle over wind flags. It’s amazing how little wind it takes to move the bullet at 100 yards. I was having to hold off today to finish up groups. That’s when it’s the most fun. — Dave Way
Dave posted in our Shooters’ Forum: “To say I was impressed with the quality of the action and the accuracy of the rifle would be an understatement. I shot five different lots of Lapua Midas, Lapua Long Range, and Lapua Super Long Range ammunition. At 50 yards all the groups were pretty tight. I was shooting in some wind, using flags. One lot seemed to stand out so I put a target at 100 yards and shot three rounds in it as aiming points. I shot three five shot groups with the last 15 rounds of that lot that I had with me. All three groups were under 1/2″ and they were getting tighter as I moved the tuner!”
Above are initial 100-yard, 5-shot groups Dave Way shot with his rifle, while experimenting with different tuner positions. The largest group (on left) was a 0.416″, while the smallest (on right) was 0.296″. The average of the three groups was a stellar 0.369″ (0.352 MOA).
Dave Way treasures this rifle and praised Alex Wheeler’s skills as a gunsmith: “I have never received a rifle from Alex that didn’t shoot incredibly well and this one is no exception. I’m just getting into the .22 world so I don’t know if this is good, great, or excellent accuracy but it seems pretty accurate to me.”
Lot Testing and Tuner Experimentation Pays Off
Here are some initial groups Dave Way shot during initial ammo testing. They are all under half-inch at 100 yards. That’s pretty impressive — but read on. When Dave optimized his tuner position and found a great lot of Lapua Super Long Range .22 LR ammo — his groups got even smaller. Dave notes: “They could have been better but I was just getting used to the trigger and everything.”
Here are a series of three-shot, 50-yard groups. You can see this rifle is quite consistent. This is with five different lots of Lapua .22 LR ammunition.
Lot Testing with Lapua Ammo — Three-Shot Groups at 50 Yards
Rifle Components
Holeshot 2500X Right Bolt, Left Port Action
Muller Works 1:16″-twist, 8-groove Barrel
Holeshot Barrel Tuner
Bix-N-Andy Trigger
Holeshot 2500X actions and Holeshot tuners are now produced and sold by Precision Quest Products.
Have questions about this ultra-accurate rig? You can discuss this Wheeler-built rimfire rifle in a current AccurateShooter Forum Thread.
Three 50-Yard Groups, All Under 0.180″ — That’s Consistency!
With the right ammo, this rig is wicked accurate. Here are three groups shot at 50 yards one after another. Dave shot these three 5-shot groups consecutively while optimizing his tuner: “Working with tuner the last two trips to the range. [It was] very consistent and pretty tight at tuner setting 162. Here are three consecutive 50-yard groups (5 shots each).” The biggest group (at bottom) measured 0.175″ (0.334 MOA), while the smallest group (middle) was a stellar 0.154″ (0.294 MOA) — that’s mighty impressive!
Alex Wheeler Crafted His Own Superb Rimfire Rifle First
Gunsmith Alex Wheeler of Wheeler Accuracy has, over the years, concentrated on ultra-accurate mid-range and long-range centerfire benchrest rifles, along with some stellar long-range hunting rifles. But Alex has started to venture into rimfire shooting. Prior to building the Dave Way rimfire rifle featured here, Alex built a “sister rifle” for himself with similar components. That gun turned out so well that Dave asked Alex to build another. And, as you can see, Dave’s new Wheeler-built rimfire rifle turned out to be a true tack-driver.
Alex credits Dave’s shooting skills: “I don’t think its possible for anyone to send a rifle to Dave that doesn’t shoot. He just has a knack for it. I’m glad I got into the rimfire stuff. I don’t have any interest in rimfire competition but it’s taught me a lot about bench manners and I get a lot more trigger time. It’s a great tool to learn wind flags with as well. It should make me a better centerfire shooter. That was really why I built mine. I normally sell every gun I build eventually and Dave was going to get mine but I said you should start gathering parts, I think I’m keeping this one!”
Lapua Long Range and Super Long Range .22 LR Ammunition
Dave Way had great results with his Lapua .22 LR ammo. Lapua Long Range and Super Long Range ammunition comes from Finland, and is designed for the growing long-range rimfire disciplines with targets at 100-300 yards. This ammo delivers very low ES and SD numbers. Our friend F-Class John tested this ammo and confirmed it performs very well (SEE Test Video).
Capstone’s Marketing Director, Geoff Esterline, explains: “Each production lot of Lapua’s [LR and Super LR] are test-fired in 50-round groups for dispersion. The results determine whether it makes Super Long Range or Long Range packaging.”
SHOT Show 2024 has just concluded. Thousands of new products were unveiled at SHOT Show, including hundreds of new rifles. Today’s Saturday Movie showcase features a number of new (or nearly-new) rifles displayed at SHOT Show 2024 in Las Vegas. This showcase gives our readers a chance to check out some of the newest hunting, precision, and tactical rifles recently featured at SHOT Show 2024.
New Carbon-Fiber Stocked Savage Hunting Rifle
The HuntStand staff had a chance to field test the new KLYM rifle series from Savage. Based on a new carbon-fiber platform, the straight-pull Savage KLYM weighs just 6.7 pounds without optics.
Top AR-Platform Rifles for 2024
AR-platform “Modern Sporting Rifles” continue to be top sellers because of their affordability and versatility. An AR rifle can be used for Service Rifle competition, 3-Gun games, varmint hunting, and of course, home defense. This video features 10 modern-generation AR-platform rifles. Many of these rifles were on display at SHOT Show in Las Vegas this past week.
MDT Chassis and Howa Rifles for 2024 — SHOT Show Report
This video, recorded this past week at SHOT Show 2024, shows some interesting new products — both complete rifles and new components. Many notable products are featured in this 24-minute video. At 16:16 the video shows the new Howa Super Deluxe Walnut rifle. This comes with a handsome figured Walnut stock and either stainless or blued barrels. Starting at 15:04 other new Howa models are shown including a new Mini-action with carbon-wrapped barrel and hinged floor plate.
At 11:05 the video covers MDT’s Zero Stage electronic trigger. First announced in 2023, this is a unique new technology for field rifles. This operates by pressure on the trigger blade, rather than backward mechanical movement. The Zero Stage trigger adjusts from 4 to 64 ounces (0.25 to 4 pounds) without tools. Last but not least, at 00:30 the MDT ACC Premier Gen 2 Chassis is shown (photo below). This has many new features, including a shorter fore-end and new components to help with rimfire magazines.
SHOT Show 2024 “Shorts” — New CZ Rifles, New AirGun
Ten Good Bolt-Action Hunting Rifles — All Under $600
This 9-minute video provides quick looks at ten affordable bolt-action rifles, all under $600.00. If you are looking for a basic hunting rifle, perhaps for a young family member, here are some options with good “bang for the buck”. Using mostly factory footage, this video covers these 10 bolt-guns:
1:04 TC Arms Venture
1:56 Mossberg Patriot
2:28 Ruger Ranch Rifle
3:10 Howa Mini Action Rifle
3:47 Howa Hogue Rifle
4:35 Thompson Center Compass
5:15 Ruger American Rifle
6:03 Winchester XPR Compact
6:52 Remington 783
7:44 Savage Axis II XP
BONUS — Get a Howa Barreled Action for Your Next Rifle Project
Howa M1500 barreled actions are great for hunting and varmint rifle projects. These Japanese-made Howa actions are smooth running and the two-stage HACT trigger is way better than most factory triggers. CLICK HERE to learn more about Howa M1500 barreled actions.
Right now at Brownells you can get a complete Howa barreled action (with trigger!) starting around $400.00. Chamberings in stock now include: 22-250, 6mm ARC, .243 Win, 6.5 Grendel (Mini), 6.5 Creedmoor, 6.5 PRC, .308 Win, and .300 WinMag. A wide variety of barrel lengths are offered, and some chamberings have carbon-wrapped barrels.
Literally hundreds of new rifle designs were displayed at SHOT Show 2024. Here are eight notable new (or recently introduced) rifles that were spotlighted in SHOT Daily magazine. We have seen trends to more modular rifles in recent years. And multiple rifle-makers are now offering very lightweight rigs for hunters.
The innovative Benelli Lupo HPR rifle boast an impressive sub-MOA, FIVE-shot factory accuracy guarantee. The new Lupo HPR combines a custom-fitment stock system with a heavy-contour, straight-fluted CRYO barrel. Many popular chamberings are offered: 6.5 Creedmoor, 6.5 PRC, .308 Win, .300 PRC, .300 WinMag, and .338 Lapua Magnum. Benelli says the Lupo HPR “incorporates the function of a chassis rifle with the handling grace and accuracy of a custom bolt-action.” CLICK HERE for image with Lupo HPR details.
The Savage 110 Ultralight Elite is a modern very light rig designed for the higher-end hunting market. Offered in multiple chamberings, the 110 Elite features a carbon-wrapped 18″ or 20″ Proof Research barrel and skeletonized carbon composite stock. The whole rig (before optics) runs just 5.8 to 6 pounds — very lightweight. The weight savings are nice, but the $3299.00 MSRP makes this a pretty pricey Savage. Chamberings are: 6.5 Creedmoor, 6.5 PRC, 7mm PRC, .308 Win, .300 WSM, and .300 WinMag. This rifle is review in the Backfire Video below at the 19:14 time-mark.
Bergara B-14 Crest rifles are offered with two models for backcountry hunters. This 100% carbon monocoque fiber stock is designed with industry-leading technologies. The Squared Crest rifle comes with a detachable 5-round AICS compatible magazine. A wide selection of chamberings are offered: .22-250 Rem, 6.5 Creedmoor, 6.5 PRC, 7 PRC, .308 Win, 300 Win Mag.
The Rock River Arms XM24 is offered in .308 Win and .338 Lapua Magnum. Priced at a hefty $5295.00, this features a non-folding MDT ESS chassis and 26″ cryo-treated barrel. The .338 LM version would be a decent out-of-the box choice for ELR shooting.
The Browning X-Bolt Ovix rifle features a Cerakoted barreled action (with brake) fitted in a handsome camo stock. The modern DLX trigger offers a crisp break and adjusts down to 3 pounds. The Veri-Tech stock, finished in Ovix camo pattern, has a unique modular grip design. This allows the sporter grip (as shown) to be swapped with a more vertical-style grip.
The CVA Cascade Long Range Hunter rifles feature 22″ or 24″ barrels with muzzle brake. Both action and barrel have a handsome tan Cerakote finish. The stocks have an adjustable cheekpiece plus a “soft touch” finish. A wide range of chamberings are offered: 6.5 Creedmoor, 6.5 PRC, 7mm Mag, 7 PRC, .308 Win, .300 PRC, and .300 Win Magnum. Prices start at $925.00 MSRP.
The Primary Weapons Systems UXR is an innovative, multi-caliber tactical rifle. The unique UXR (User Xchange Rifle) allows users to quickly switch chamberings by exchanging just three parts: barrel, magwell, and bolt head. Initially available in 5.56×45 and .300 BLK variations, the UXR platform will also be available in .308 Win and 8.6 BLK configurations later this year.
The new Springfield Armory Model 2020 Redline is lightweight, custom-grade hunting rifle currently available in 6.5 Creedmoor and .308 Win. Featuring a minimalist Grayboe Trekker stock and outfitted with a 16″ or 20″ carbon-wrapped barrel, the Redline is suppressor-ready and carries a .75 MOA guarantee.
38 More Guns in BackFire Video Review
If these Quick Pix just wet your appetite and you want to see even more rifles, watch this 41-minute Backfire Channel video. The host reviews 38 different firearms, mostly rifles. The gun he’s holding in the video “cover shot” is a custom rifle with a Rem-clone action in a Matterhorn metal plus wood laminate stock. (See 15:40 time-mark).
In the video you’ll notice a cameo appearance by Eric Cortina at 8:20 time-mark. Eric notes that Caldwell has a new radar chronograph that can calculate bullet BC. The host then showcases the new Caldwell VelociRadar chronograph at the 8:52 mark. It’s quite a bit bigger than the new Garmin Xero C1 Chrono, but it has a nice rugged housing and costs $100 less.
SHOT Show 2024 has been running January 22-26, 2024. Here are FREE digital magazines covering many new products displayed at the show. We’ve embedded three digital versions of the SHOT Daily print magazine provided to SHOT Show attendees. You can navigate page by page with the left/right white arrows in the gray box below. To quickly scan through an entire 60+ page digital magazine, use the slide bar. When you find content you want to read, use the zoom control or click the FULL SCREEN brackets icon at lower right.
We highly recommend two big feature stories. In the Day 1 Edition, check out the Guns 2024 article starting on page 30. You can also read the New Rifles section of this story on the SHOT Show Website. In the Day 2 Edition, look for the Optics 2024 article starting on page 40. And in the Day 3 Edition, New Electronics (including Garmin Xero C1 Pro Radar Chrono) are covered starting on page 40. NOTE: These magazines are large digital files that may take a few seconds to load fully. Click the titles below to read each of the four 2024 SHOT Daily issues.
The daily news of the 2024 Las Vegas SHOT Show is brought to you by NSSF and Grand View Outdoors, a division of Cole Publishing. Click each cover image to launch full digital magazine.
If you’re using a body die or a full-length sizing die, try using Ballistol (in the aerosol can) as a lube. It works GREAT without the tacky or gooey residue left by most case lubes. It will also clean off carbon residues on the neck as you lube the case. Just spray a little on a cotton patch (or your fingertips) and wipe each case before you run it up into the die. If you are using a steel neck bushing, be sure to wipe the neck as well. You can usually do a half-dozen BR-sized cases before you need to re-apply Ballistol on the patch. Ballistol is non-toxic, bio-degradeable, and will not harm your skin. It is very slippery, but can easily be removed with a rag or paper towel. Try it–you may retire your One-Shot. Ballistol can also be used to protect wood stocks.
For Neck-Turning, Try STP Blend or Assembly Lube
Another even cheaper option is assembly lubricant. For turning his case necks, RStreich uses assembly lube from an auto parts store. He notes: “The brand I have is reddish in color and kind of sticky like honey. It’s far better than the Imperial die wax I was using before.” There are a variety of types, both with and without moly additive, and you can select the viscosity you prefer if you sample a few brands. Be sure to clean out any lube residue from the inside of your necks when you have completed your neck-turning.
