Report by Monte Milanuk
With the proliferation of wide bipods for competitive F-TR shooting, we’ve seen a lot of cool gear hitting the market. Whatever you can imagine, someone is either building now, or working on prototype plans. One new design that seems to have stayed under the radar thus far is the FLEX bipod by Dan Pohlabel.
The FLEX bipod’s designer, Dan Pohlabel, offers these instructions:
The bipod feet are shipped loose. Note there is a left foot and a right foot. Mount them as shown in the diagram above. Determine the balance point of your rifle and mount the bipod approximately two inches forward of that point. You may want to move it further forward after shooting. Experiment with its placement to minimize movement of the bipod. When setting up, first grab each foot and ‘dig’ them in to the shooting surface, dirt, gravel, grass, carpet — it doesn’t matter. After making sure each foot has a hold, raise or lower the bipod to your target and use the cant adjustment to level your rifle. Loading the bipod with your shoulder is the preferred method of position. Contact me with any FLEX bipod questions you may have: danielp123 [at] earthlink.net.
The FLEX bipod is a very simple design — no Mariner’s wheel for vertical adjustment, no joystick head, no changing width as it goes up and down. And the FLEX bipod is very light (as are most, these days), but also very durable. I haven’t actively tried to destructively test it, but so far it’s held up to being tossed in the back of the truck, hauled around to the range and everywhere else in between. It definitely has not been ‘babied’ in any way, and it’s not noticeably any worse for wear. An added bonus is that it breaks down very flat for airline travel. Once I take the feet off, remove the ratchet lever (with screw), the whole bipod nestles very nicely in the bottom layer of foam in my gun case (with cuts for the head etc. in the foam). I’m definitely not worried about it in there. If someone bashes the case hard enough to damage what is essentially a plate of spring steel, then I’ve got bigger worries.
This view (below) shows a bit of the adjustment controls. Each leg has independent control for height, and there is a ratcheting locking lever that controls the cant. Instead of being directly centered like most other designs I’ve seen, this one is off-set a little, allowing a fair amount of movement without allowing it to completely ‘flop’ over to one side. (By contrast, using other bipod designs, I’ve had guns literally flip over as they tipped over too far.) Also having the tilt control relatively close/tight to the bore of the gun helps with the stability as well.
Inventor Dan Pohlebel developed the FLEX bipod for use in his native Ohio, where apparently grassy firing lines are the norm. Here in the Pacific Northwest, I seem to encounter concrete or gravel more often, which is why I usually place a mat under the bipod to keep it from sinking in too far. On Dan’s newest models, the “feet” have teeth to give better traction on hard surfaces such as the hard-pack clay/dirt (beneath a skim layer of gravel) that you’ll find at Raton, NM.
Why would you want more traction? Well, not everyone wants a bipod that slides around like a hog on ice. Some people manage to get things tracking straight back and forth, almost like it was constrained by a front rest. Personally, I have a hard time doing that in a repeatable fashion. While the FLEX Bipod shoots quite well with a [loose] hold, it was designed for those of us who like to ‘lean’ into the gun a bit. Quite literally, the idea is that you get the feet to dig in slightly, and push against the rifle butt with your shoulder and the bipod will ‘flex’ or bow forward slightly. It is one of those things that sounds wonky until you try it. It may take a few times to get a feel for it, but once you do, it is surprisingly repeatable.
The system does have a few quirks to it. Personally, I wish the rail attachment had a ratchet lever like the pivot control. Currently you need a separate tool to take the bipod on/off the gun. Also, the FLEX bipod seems to work better mounted somewhat further back than other designs. Some experimenting may be necessary to find what works best. Then again, we all need more trigger time….
Most of our readers know that MTM Case-Gard offers a vast selection of ammo boxes for pistol, rifle, and shotgun ammunition. However, with such a wide inventory of box styles and sizes, it can be difficult, at first, to select the right box for your particular cartridge and carrying needs. MTM has now simplified that task by publishing comprehensive Ammo Box Charts on its website. Just log on to the Box Charts Page, and select Rifle, Handgun, or Shotshell boxes. That will open a large chart listing cartridge types, small to large, in the left column. Pick your cartridge and you will see all the storage options. MTM even codes the entries so you can see if a box allows Tip Up AND Tip Down storage, Tip Down only, or Tip Up only. For most popular rifle cartridges, there are 20-round, 50-round, and 100-round cases. Below is the first part of the Rifle Ammo Box Chart. The entire chart is four pages long.
New MTM Ammo Belt Pouch
MTM has also introduced a handy product that should work great for rimfire shooters. The new MTM Ammo Belt Pouch conveniently holds 100 rounds (two boxes) of .22LR rimfire ammo. With a sturdy snap latch and heavy-duty belt clip, all you have to do is pour out the ammo, then clip the pouch on your belt or jeans pocket. The Belt Pouch is also handy for saving fired centerfire brass.
Suggested retail for MTM’s Ammo Belt Pouch is a modest $4.95. However, Grafs.com currently sells the item for $3.59 (Prod. #MTMABP). Designed to hold a 100 rounds of 22 long rifles. Holds: .22 Long rifle, 22 Magnum, 22 Short, 17 Win Super Mag, 17 HMR, 17 Mach 2, Pellets, and BBs.
Nancy’s book is finally shipping! The updated Second Edition of Nancy Tompkins’ book, Prone and Long Range Rifle Shooting, is now in stock and can be ordered from RifleShootingbyNancy.com. Price is $45.00 including shipping in USA, or $59.00 with shipping in Canada (overseas price is $68.00).
The Second Edition is bigger and better than ever. The new, 382-page Second Edition features color photos, and the book is now a hardback for greater durability. The Second Edition contains a new section on F-Class shooting and you’ll find new and updated information throughout the book. Nancy, the first woman to win the NRA National High Power Championship, is one of the greatest competitive rifle shooters in history. In her book she shares insights that can assist rifle shooters of all levels, in a wide range of disciplines. You’ll learn about shooting fundamentals, wind/mirage reading, body positioning, sling use, gear selection, match preparation, visualization techniques, and much, much more. The book also includes sections by Middleton Tompkins on reloading, equipment, and building a Palma rifle. CLICK HERE for Complete Topic List by Chapter.
Nancy Tompkins — A Truly Legendary Rifle Shoter
Nancy Tompkins has been shooting competitively for over 38 years. She has won the National Long Range Championships 4 times (1986, 1997, 1999 and 2003), the across-the-course National High Power Championships (1998), the Metric Smallbore Nationals (2012) and the Fullbore Nationals (2012).
Nancy has also been the Wimbledon Cup winner (1993) and a 7-time Leech Cup winner (1995, 1997, 1999, 2003, 2005, 2011 and 2012). She has won both team and individual medals in the World Championships and has been on seven Palma Teams (as both a shooter and a coach).
Forum member Roy Bertalotto has found a great print resource for cast bullet shooters. Roy, who runs the RVB Precision website, has started casting his own bullets. Roy tells us: “I recently joined the Cast Bullet Association (CBA) as I’ve discovered the great hobby of casting my own bullets for long range ‘Buffalo Shoots’ and Cowboy Action Shooting.” Roy says he found the information he needed in the CBA’s own guide to bullet casting: “The CBA offers a fantastic 496-page book, mostly prepared by members, on absolutely everything you’d ever want to know and more about bullet casting.”
Cast Bullets For Beginner and Expert (Second Edition) is a collection of articles from serious cast bullet shooters, covering every subject imaginable. Compiled by Joe Brennan, this new edition has updated information. This Second Edition is now available for $29.95 with free shipping in the USA.
You can order this book online, or send a $29.95 check to: Eunice Birmley, CBA Director of Services, 47 Pinon, Cimarron, NM 87714
I have been looking for a bag that can securely carry a large spotting scope as well as chronograph hardware, wind meter, and camera gear — all the extra stuff I typically take to the range in addition to the essential cleaning and shooting products that go in my regular range kit. The folks at Grizzly Industrial told me to check out their new 20″ Range Bag by Bald Eagle. These 20″ Range Bags, are very versatile and well-made. With eyepiece removed, my jumbo-sized Pentax PF-100ED spotting scope fit perfectly inside the padded central compartment. At the same time I could haul ALL the peripherals for my PVM-21 chronograph, plus a camera, wind meter, spare Pentax eyepiece, AND a netbook computer. Without the netbook, there is room for four pistols along the side channels. If you don’t need to pack a large spotting scope, the main compartment could easily hold 3 more pistols in Bore-Store socks, plus holsters, ammo boxes, and earmuffs.
Watch the video to see how much stuff will fit in this bag. NOTE: If you carry a tripod or windflag stand using the straps under the case lid, be sure to position the foam padding carefully to prevent any direct contact with a spotting scope in the main compartment. Overall, the 20″ Range Bag is a remarkably capable gear-hauler. With the nicely-padded interior it will safely carry expensive items such as laser rangefinders, and binoculars. There is also a slash pocket on the rear side (not shown in video) that will hold thin items such as target stickers and shooting log-books. The 20″ Range Bag is offered in four (4) different colors: Red, Black, Green, and Camo. Price is $59.95 for solid colors and $61.95 for camo.
Smaller, 15″ Range Bag Offered Also
Grizzly also sells more compact, 15″-wide Bald Eagle Range Bags. There are six (6) color choices for the 15″ Range Bag: Red, Black, Navy Blue, Green, Hot Pink (for ladies), and Camo. Solid colors cost $45.00, while the Camo Bag costs a couple dollars more ($46.95). If you don’t need to haul a spotting scope, you may prefer the smaller version. The 15″ version still offers lot of carrying capacity — it’s big enough to hold ammo, muffs, target stickers, and much more.
REVIEW Disclosure: Grizzly Industrial provided the 20″ Range Bag for testing and evaluation.
There is a new player in the field of elite die-makers: Whidden Gunworks. John Whidden’s Georgia-based company is producing outstanding full-length sizing dies and micrometer-top seater dies for 7/8-14 thread presses. The dies look great, work great, and produce very straight and accurate ammo. The Whidden dies are finished beautifully inside and out. They are priced competitively and they are available for popular “extreme accuracy” cartridges such as the 6PPC, 6mmBR, 6mmBRX, 6 Dasher, 6XC, 6.5×47, .260 Rem, .284 Win, and .308 Win (and more). If you are looking for a die set for your new precision rifle, you should definitely check out the Whidden dies. Two-die set, FL Sizer and Micrometer-top Seater, costs $184.99. Sizer die alone is $74.99, while Seater die alone is $109.99.
Many of our Forum members have started using Whidden dies — and they are reporting very positive results. I personally own and use a set of Whidden dies, and I am very, very impressed with them. Here’s my report:
Editor’s Report on Whidden Dies I have a set of Whidden Gunworks dies for my personal 6BRDX (a chambering similar to 6 Dasher but with longer neck). The dies are excellent and they produce very straight ammo. My loaded rounds (made with a Whidden bushing-type FL sizer and Whidden micrometer-top seater) are showing less than .0015″ run-out measured on the bullet, with the majority closer to .001″ run-out. (This is with Lapua Scenar L bullets, which have great jacket uniformity and concentricity.)
One thing I immediately noticed about the Whidden seater die is that there is a very close correspondence between the seater “hash marks” and true changes in seating depth. By this I mean when you dial a value change of 10 on the micrometer scale, you get very close to a .010″ change in seating depth. It is not perfect, but it is definitely more precise than most other micrometer-top seater dies I’ve used (both hand dies and 7/8-14 thread screw-in types).
Cartridges loaded with my Whidden sizer and seater dies have proved very accurate. My 6BRDX is shooting in the mid-ones for five shots at 100 yards. I also have a micrometer-top Wilson inline seater die that was custom-bored with my chamber reamer. As far as I can tell, the ammo loaded with the screw-in Whidden seater is every bit as accurate as rounds loaded with the Wilson die using an arbor press. Additionally, with the Whidden micrometer die, I can hold extremely tight tolerances on base-to-bullet-ogive lengths.
In the past, with my 6mmBR, I favored an inline die because I thought it offered better control over seating depth. But given how well the Whidden seater works, I’m not sure I’d gain anything with my Wilson hand die. At least when used with a quality Harrell’s benchrest press, the Whidden seater gives up little or nothing to the hand die, and that’s big news in my experience.
You will like the look and feel of these Whidden dies. The finish inside and out is very, very good — the dies have a quality feel and run very smoothly. Both the sizer and seater have a fluted section — this offers a better “grip” when you’re screwing in the dies. The outside of the seater has a smooth, gloss-anodized finish — it exudes quality. The markings on the seater’s micrometer ring are crisp and very legible, with large, high-contrast white-on-black lines and numbers.
One other very cool feature of the Whidden sizing dies is that custom-sized tapered expanders will soon be offered. Whidden plans to offer expanders in .0005″ (one-half thousandth) increments. This is great if you have, say, a .265 bushing and a .266 bushing but you want just a little less neck tension than the .265 offers. With the tapered expander, I can use a 0.265 bushing followed by an 0.2655 expander — allowing more precise control of neck “grip”.
Whidden Die Features
Die Dimensions well-matched to PT&G reamers used for match chambers.
Sizing dies spec’d for easy chambering and extraction without overworking brass.
All sizers include shoulder datum collar to measure shoulder “bump” and headspace.
Neck bushing or no-neck bushing configurations.
Bushing dies use standard Redding/Wilson type bushings.
Neck diameter of non-bushing FL sizers can be set to customer specification.
Extended threads on short cartridge sizer dies such as BRs.
Coming soon: custom expander balls (in half-thousandth increments) to adjust neck tension and provide minimum working of the case neck.
Seater: Floating sleeve on micrometer seater enhances concentricity of loaded rounds.
Seater: Large, high-contrast markings for easy adjustment.
Custom Dies for Wildcats or Your Cartridge
Custom-made for your wildcat or standard cartridge.
Can work from fired brass or a chamber drawing to match your chamber exactly.
Neck-bushing die, or no-bushing die with neck diameter bored to customer specification.
Available Die Sets
Here is the current caliber list. Micrometer seaters are available in all calibers listed below except 22BR and 22 BRX.
John Whidden Talks about Sizers, Seaters, and Expanders
There are two sides to our die business. First we are stocking dies in many calibers that are of interest to those who visit this website (such as the 6PPC, 6mm Dasher, 6.5×47 Lapua, .260 Rem, 7mm Shehane, .308 Winchester). These dies are a good fit to the “match chamber” reamers and very few people with these calibers should have to have “Pure Custom” dies made. We have both sizers and micrometer-top seaters ready to go for the many cartridge types listed above. The sizer dies will include a shoulder datum collar that makes it easy to measure shoulder “bump” during the full-length sizing process. This is important to control headspace precisely.
On the “Pure Custom” side, we have a huge amount of flexibility. We can make one-of-a-kind sizers and seaters for wildcats in a short period of time and at an excellent price. We can work with the customer to make full-length sizers, neck sizers, shoulder bump dies, small base dies, or most anything else they can need. We can of course provide micrometer-top seaters for these cartridges as well. We can make non-bushing sizers with specific neck inside diameters tailored to customer specifications.
We will also be offering custom-sized expanders. These expanders will fit our dies as well as Redding dies. Our tapered expanders will be available in .0005” (one-half thousandth) increments for the common calibers. In our shop we have had excellent results using expanders in the dies as long as the expanders provided the correct amount of neck tension and didn’t overwork the brass. Expanders have gotten a bad reputation in recent years but we find them to be excellent tools when the same precision is applied to their use that careful handloaders apply to the rest of their process. Expanders can be most valuable for those who choose not to neck-turn their brass (because the expander pushes neckwall variations to the outside).
One last thing — many gunsmiths with their own wildcats (or “specialty” chambers) have asked us to provide dies for their customers. We gladly do batches of custom dies and encourage gunsmiths to contact us. — John Whidden
McMillan Group International (McMillan) has added three new lines of ammunition: Extreme Velocity ammo (optimized for long range), McMillan Precision ammo (match quality for hunting), and McMillan Tactical ammo. All three new types of ammo are loaded with premium bullets. McMillan claims that its precision cartridge-loading methods ensure: “better concentricity, better uniformity of velocity, [and] better uniformity of pressure”. Along with these three NEW ammo types, McMillan already offers African Dangerous Game ammunition (ADG).
McMillan Extreme Velocity Ammunition — Long Range McMillan’s Extreme Velocity (ExVel) ammunition utilizes high-BC Berger Bullets exclusively. Powders are selected for High FPS and low ES to minimize vertical spread at long range. ExVel ammo was designed with input from Bob Beck of Extreme Outer Limits TV.
McMillan Precision Ammunition — Hunting In its new Precision line, McMillan offers traditional hunting cartridge types. Barnes LRX, TSX, and TTSX bullets with excellent accuracy AND strong terminal performance are used. All critical cartridge measurements are held to precision tolerances and Powders are selected for consistent velocity. Each round is hand inspected.
McMillan Tactical Ammunition McMillan’s Tactical ammunition offers .308, .300 WM, .338 LM, and 50 BMG cartridges loaded to “match-quality standards”. Bullets are carefully selected for mission-specific applications and powders are selected for low ES to minimize vertical spread at extreme long ranges. Each round is hand inspected.
At SHOT Show we checked out the all-new, side-focus 15-55x52mm Competition™ Scope from Nightforce Optics. This comes in both Silver finish and Matte Black. The black version looks like an NXS. The silver looks good but the finish is pretty shiny and contrasts with the black controls (some folks will like that, others won’t). We worked the knobs and side-parallax controls. The clicks are positive and the dial resistance seems just about right (very similar to an NXS). The ED (low-dispersion) glass in the new 15-55X provides high contrast, low chromatic aberration, and 92% light transmission. And this scope is a LOT lighter than the current 12-42x56mm — nearly half a pound less! The new 15-55x52mm sells for $2231.00.
Watch Video to See NF 15-55x52mm Competition Scope (and B.E.A.S.T. sneak preview.)
The big news is that, with a weight of just 27.8 ounces, the new 15-55X Nightforce Competition Scope is 24% lighter than the NF 12-42×56 Benchrest model, and 20% lighter than the NF 12-42×56 NXS. Like the NXS series, the new Competition scope offers side parallax adjustment; and, it will focus from 25 yards to infinity, making it suitable for rimfire and airgun shooting as well as centerfire competition. The turrets provide positive and repeatable .125 MOA (eighth-minute-of-angle) clicks. Each rotation provides 5 MOA of adjustment. And we’re pleased to see that the Competition Scope offers a full 60 MOA of travel — for both windage and elevation. That’s impressive. We’re pleased to see the new scope offers a fast-focus, European-style diopter eyepiece (photo below right). Two reticles will be offered initially: the CTR-1 (fine crosshair with target dot) and DDR (double dot with hold markers). You can see the reticles in the video above.
Thankfully, you won’t have to wait long to get a 15-55x52mm Comp Scope. Nightforce says it will start shipping in mid-February. CLICK HERE for more information.
Does your rear sand-bag get lumpy or lose its shape during transport? Are your bag ears starting to sag or get mis-aligned? Well the clever Italians have a solution for you.
Varide Cicognani, an Italian webstore specializing in competition shooting accessories, offers a cleverly-designed bag transport/storage caddy for rear sand-bags. Cicognani’s Portacuscino Model TFC-P is designed to keep your rear bag “in shape” during transport and storage. The TFC-P features aluminum top and bottom brackets, connected with threaded rods. A wedge under the top bracket fits between the bag ears. The top bracket has a convenient carry handle. The whole unit (not including bag) weighs just 13.4 ounces (680 grams). The price is € 49, or $65.99 at current exchange rates. For more information, visit www.VarideCicongnani.it.
Product Tip by Boyd Allen. We welcome reader submissions.
Gary Eliseo of Competition Machine is now offering a tube-gun chassis kit for the Tikka T3 action. This T3 Chassis Kit is the latest design in Gary’s Light Weight Hunter Series. The T3 kit will initially be right-hand only, and will fit AICS short action magazines. This is a “no gunsmithing” installation — no modifications to the action are required and the chassis kit works with the factory T3 trigger and safety.
Tikka’s T3 action is rigid and robust. It cycles smoothly and has a short 75° bolt lift. The T3 features a Sako-style extractor, with angled-leading-edge bolt lugs for smooth lock-up. The T3 action can be installed in Gary’s Chassis Kit with either a recoil disc (and bolts) or glue-in action mounting. The Chassis Kit is designed to accept AR15 buttstocks.
Eliseo’s current T3 Chassis Kit handles short-action cartridges only — for now. Gary is considering bringing out a version with a long-action-length magwell if there is sufficient demand.
Price is $685.00. This includes a rugged Cerakote finish. Tikka T3 action and AICS 5-round or 10-round magazines sold separately. For more info, visit GotXRing.com, call 714-630-5734, or send email to: spraynandprayn [at] gmail.com . CLICK HERE for order page.
Product Tip from EdLongrange. We welcome reader submissions.
Most of our readers know that 
New MTM Ammo Belt Pouch
Nancy Tompkins — A Truly Legendary Rifle Shoter
I have been looking for a bag that can securely carry a large spotting scope as well as chronograph hardware, wind meter, and camera gear — all the extra stuff I typically take to the range in addition to the essential cleaning and shooting products that go in my regular range kit. The folks at 
Watch the video to see how much stuff will fit in this bag. NOTE: If you carry a tripod or windflag stand using the straps under the case lid, be sure to position the foam padding carefully to prevent any direct contact with a spotting scope in the main compartment. Overall, the 20″ Range Bag is a remarkably capable gear-hauler. With the nicely-padded interior it will safely carry expensive items such as laser rangefinders, and binoculars. There is also a slash pocket on the rear side (not shown in video) that will hold thin items such as target stickers and shooting log-books. The 20″ Range Bag is offered in four (4) different colors: Red, Black, Green, and Camo. Price is $59.95 for solid colors and $61.95 for camo.
Available Die Sets
There are two sides to our die business. First we are stocking dies in many calibers that are of interest to those who visit this website (such as the 6PPC, 6mm Dasher, 6.5×47 Lapua, .260 Rem, 7mm Shehane, .308 Winchester). These dies are a good fit to the “match chamber” reamers and very few people with these calibers should have to have “Pure Custom” dies made. We have both sizers and micrometer-top seaters ready to go for the many cartridge types listed above. The sizer dies will include a shoulder datum collar that makes it easy to measure shoulder “bump” during the full-length sizing process. This is important to control headspace precisely.
McMillan’s 
In its new 
McMillan’s 
At SHOT Show we checked out the all-new, side-focus 
Does your rear sand-bag get lumpy or lose its shape during transport? Are your bag ears starting to sag or get mis-aligned? Well the clever Italians have a solution for you.
Tikka’s T3 action is rigid and robust. It cycles smoothly and has a short 75° bolt lift. The T3 features a Sako-style extractor, with angled-leading-edge bolt lugs for smooth lock-up. The T3 action can be installed in Gary’s Chassis Kit with either a recoil disc (and bolts) or glue-in action mounting. The Chassis Kit is designed to accept AR15 buttstocks.
