|
|
June 27th, 2013
 Lyman’s new E-Zee Trim Case Trimmer allows you to easily trim cases by hand or with an electric drill (for power). With both pistol and rifle brass, a cartridge-specific pilot affixed to the cutter head slips into the case. Case trim length is set by the length of the pilot. You need a different pilot for each cartridge type you intend to trim. Pilots are offered in rifle sets and pistol sets, or pilots can be purchase individually for $4.95 each. For $29.95 you can get a complete kit (for either rifle or pistol cases) that includes: case-locking device, cutter, five (5) trim-to-length pilots, and both hand and power trimming adapters.
The Lyman E-Zee system is versatile. Using the same case-holder, you can trim-to-length manually, or use the included power-adapter fixture to drive the cutter with a cordless drill (you still hand-hold the case). We think power is the way to go. Your hands get tired after manually trimming just a handful of cases. The trimmer comes with a case locking device, cutter, trim-to-length pilot, cutter head and both hand and power trimming adapters. The trimmer works with any standard shell-holder including Lyman, Redding, RCBS, Hornady & Lee Precision.
Editor’s Comment: With this system you have very limited control over cut length. OAL is preset based on the pilot dimensions. Also the cutter blades are not as sharp as those you’ll find on a Forster or Wilson trimmer. And there are only ten (10) types of rifle pilots — no 6mmBR, no PPC, no 6XC, no 6.5×47, no .284 Win. For these reasons, we wouldn’t select a Lyman E-Zee system as a primary rifle case-trimming system (though we can see how it might appeal to .223 Rem and .308 Win shooters).
 On the other hand, with the inexpensive set of pistol pilots, you can trim ALL the most popular handgun cartridge types: 9mm, .38 SPL, .357 Mag, .40 SW, .44 Mag, and .45 ACP. Having a pre-set trim length isn’t a problem for pistol brass. In fact it’s normally a good idea to trim all your brass (of a particular cartridge type) to the same length so that you get a uniform crimp on every case. The complete handgun E-Zee Trimmer kit, with pilots for 9mm, 38 SPL, .357 Mag, .40 SW, 44 Mag, and 45 ACP costs just $29.95. If you reload pistol ammo and don’t yet own a power-capable case-trimmer, Lyman’s E-Zee Trim may be a good choice. For under $30.00, the E-Zee Trim is definitely worth considering for handgun brass trimming chores.
June 26th, 2013
 On his Facebook page, Hall-of-Fame shooter and ace gunsmith Thomas “Speedy” Gonzalez unveiled an impressive new F-Open rifle built for Bret Solomon. The rifle features Speedy’s new low-profile F-Class stock.
Bret’s gun is chambered for his 300 Solomon wildcat, shooting heavy 210gr bullets, so it can can be a real shoulder-buster, without some kind of buffer. The stock is fitted with a Ken Rucker’s Bump Buster hydraulic recoil reduction system to tame the recoil. The Bump Buster was originally designed for shotguns and hard-hitting, big game rifles. It is interesting to see this hydraulic buffer adapted to an F-Open rig.
Here you can see Bret shooting the gun, coached by Nancy Tompkins and Michele Gallagher:
Bret’s gun features a stainless Viper (Stiller) action, barrel tuner, and an innovative Speedy-crafted wood stock. Speedy says this stock design is all-new: “It is a true, low Center-of-Gravity F-Class stock, not a morphed Palma stock merely cut out on the bottom”. See all the details in this short video:
Stock Features: Glue-in or Bolt-In and Optional Carbon Pillars and Cooling Ports
Speedy explained the features of the new stock design: “Terry Leonard and I started working on an F-Class version of his stocks last year during the F-Class Nationals and came up with what he and I consider the first true low-CG stock in the sport. As you can see by the videos, there is very little torqueing of the stock during recoil. I add the carbon fiber tunnel underneath the forearms to save Terry some time. This bonds very well to his carbon fiber skeleton within the stock adding addition stiffness to the forearm to support the heavy barrels found on the F-Class rigs. We are playing with both glue-ins like we benchresters use and bolt-ins as well. The rifles on the videos are glue-ins. Bret just took delivery today of his first bolt-in employing carbon fiber pillars and the first Leonard stock ever to have cooling ports.”
Need for Recoil Reduction Follows F-Class Trend to Bigger Calibers and Heavier Bullets
In recent years we have seen F-Open competitors move to bigger calibers and heavier bullets in pursuit of higher BC. There is no free lunch however. Shooting a 210gr .30-caliber bullet is going to produce much more recoil than a 140gr 6.5mm projectile (when they are shot at similar velocities). Does this mean that more F-Open shooters will add hydraulic buffers to their rigs? Will a recoil-reduction system become “de rigueur” on F-Open rifles shooting heavy bullets?
Our friend Boyd Allen observes: “You may imagine that shooting a short magnum, or even a .284 Win with heavy bullets, involves a fair amount of recoil, and in the prone position this can be more than a little wearing. It can in fact beat you up over the course of a match. Some time back, Lou Murdica told me about having a hydraulic recoil absorbing device installed on one of his F-Class rifles, chambered in .300 WSM. Lou is shooting heavy (210-215gr) bullets so the recoil is stout. According to Lou, the hydraulic recoil-reduction system made all the difference.”
Story tip from Boyd Allen. We welcome reader submissions.
June 26th, 2013
 Bob Munden, one of the greatest trick shooters ever, passed away in December of last year. If you never had a chance to see Bob work his magic with a six-gun (or other firearm), here’s your chance. Tonight’s edition of Shooting USA’s Impossible Shots, features some of Bob Munden’s “greatest hits” from over the years. Before his passing, Bob was a regular on the Impossible Shots TV show.
On tonight’s episode, Munden flicks coins with his Peacemaker, making them spin like a top. Bob was famous for this and other tricks — like splitting playing cards in mid-air, and shooting the fletching off an arrow. Munden was famous both as a trick shooter and as a speed-draw specialist, with fast-draw records listed in the Guinness Book of World Records.
Air times for the Bob Munden episode on Shooting USA’s Impossible Shots are listed below. The show airs Wednesday Nights on the Outdoor Channel, and is repeated late Friday/Saturday:
Impossible Shots Wednesday:
Eastern Time: 2:30 PM, 7:00 PM
Central Time: 1:30 PM, 6:00 PM
Mountain Time: 12:30 PM, 5:00 PM
Pacific Time: 11:30 AM, 4:00 PM |
Impossible Shots Friday/Saturday:
Eastern Time: 1:00 AM SAT
Central Time: 12:00 AM Midnight
Mountain Time: 11:00 PM
Pacific Time: 10:00 PM |
June 25th, 2013
AmmoBammo.com, an all-new auction website for guns, ammo, and gear, has just opened for business. This new site boasts “no listing fees ever”. Unlike Gunbroker.com, AmmoBammo has a very simple payment structure. There is no “up-front” listing fee, and no membership fee. If an item sells, AmmoBammo takes 2.5% of the proceeds — no matter what the price. That makes it easy to figure out what it will cost to sell your gun or gear. If nobody bids, or the bids don’t reach your thresh-hold reserve price, you pay nothing. If your product sells, you pay a flat 2.5% final value fee. That seems reasonable to us. Read detailed terms of sale here.
To celebrate its launch, AmmoBammo.com is offering a special promotion. Now through July 15, 2013, AmmoBammo is Waiving ALL Fees on auction listings, including the normal 2.5% final value fee. So, for the next couple of weeks you can sell your stuff, and not pay a penny.
Since this site is brand new, listings are sparse to say the least. As of June 25, 2013 at 12:00 pm, not a single gun was listed for sale (though there were many ammo listings). Hopefully the AmmoBammo site will gain traction as more sellers list their merchandise in the weeks and months ahead.
June 25th, 2013
A new ammunition manufacturer has started up in Stevensville, Montana. ProGrade Ammunition will be offering a wide spectrum of ammo products, with components selected for particular types of shooting. Prograde will eventually offer nine separate types of pistol and rifle ammunition: Defense Grade, Varmint Grade, Cowboy Grade, Hunter Grade, Bear Grade, Range Grade, Match Grade, Safari Grade and Tactical Grade. Our readers will probably be most interested in the “Match Grade” and “Varmint Grade” lines. The Match Grade ammo features mostly Berger bullets (with some Noslers and Sierras), while Varmint Grade ammo is loaded with Barnes, Hornady, and Nosler bullets.
Click Images to Load Full-Size Images (with larger type)
 
We have no idea whether ProGrade Ammunition will shoot well and prove reliable. We don’t know what brass, powders, or primers ProGrade will be using. In a recent press release, ProGrade touts its Match Grade products: “Match Grade rounds are all hand-loaded in the United States and use premium components that are held to higher standards of consistency, leaving little room for inaccuracy. Match Grade means every element is made to be as uniform as possible in weight, primer pocket and neck size. This means everything — from bullet weight and powder weight to brass thickness and case length — is as precise as possible.”
Time (and rounds on target) will determine if ProGrade ammo is good stuff. But in this period of shortages, with ammunition of all kinds being hard to find, it is good to see a new domestic ammo-maker getting into the business, and producing cartridges with high-quality projectiles. We wish the folks at ProGrade success in their endeavor. To learn about ProGrade’s full line of ammunition, call (435) 865-5995, or visit www.progradeammo.com.
June 24th, 2013
Colt’s Manufacturing Company LLC (Colt) is introducing a line of ammunition for Colt tactical and competition rifles. This new Colt-branded “Hunting and Defence Match” ammo will be manufactured by Black Hills Ammunition. The initial offerings are designed for rifles chambered for 5.56×45 NATO and will feature 55gr and 77gr Sierra match bullets. According to the Guns.com Blog: “The 77-grain cartridge may strike a few people as somewhat familiar. It is for most purposes Black Hills MK 262 77-grain ammo… considered by many to be the best factory-loaded 5.56 NATO ammunition on the market.”
Colt Claims Ammo Will Shoot 1-MOA Groups at 500 Yards
Colt says its ammunition will deliver long-range accuracy. During the development process, this line of Colt ammo was ballistically tested in Colt rifles with a requirement of consistent five-shot, one-MOA (5″) groups at 500 yards. Colt calls this the “triple-nickel” standard (5 shots, 5″, 500 yards). Colt claims that the “Triple Nickel” capability of its ammo “assures the experienced shooter incredible performance right out of the box, with no need for load development or experimentation.”
Holding 1-MOA at 100 yards is not that exceptional. But maintaining 1-MOA groups at 500 yards would be impressive indeed. This would require consistent powder charges and tight bullet-seating length tolerances to keep vertical dispersion to a minimum. It will be interesting to test the Colt-branded ammo when it hits the market and see if it works as well as claimed.
“We’re very proud of the ‘Triple Nickel’ requirement of this ammunition,” said said Joyce Rubino, Vice President of Marketing for Colt’s Manufacturing: “Our goal with Black Hills was to bring to market a superior line of ammunition for sport shooters to use in Colt rifles, and we feel we have achieved this through the partnership with Black Hills.”
June 23rd, 2013
 We are sad to announce the passing of Duane Capehart, a leading figure in the long-range shooting community. Duane passed away in early June, and is survived by his wife Pat. Duane was one of the game-changing Montana marksmen who smashed records at the Missoula Deep Creek range.
Duane was always ready to share his knowledge with fellow shooters, and he helped this website with many projects. His friend Tom Mousel tells us: “Duane was among a handful of guys that started 1000-yard benchrest here in Montana. The man was breaking records before most of us knew what ‘MOA’ was, and he remained competitive to the very end. He and his wife Pat were the backbone of our club for many years. I will miss you my friend.”
We are much diminished by Duane’s passing. Those who knew Duane are very saddened by this loss. Here are some remembrances from our Forum members:
Duane Capehart was a truly great Hall of Fame shooter and a noble man. I am grateful for the wisdom he shared with me. He was a great fellow shooter at the range, that he helped build, especially on those frosty mornings. He never hesitated to help a new shooter. He was a good friend and neighbor here in the Bitterroot. He will be long remembered. My condolences, Pat. — Greg R.
Duane and I shot together many times and always had lots of fun before, during, and after the shoots. He will be missed for sure by the 1000-yard community and especially by the Missoula bunch. God bless you Pat, our thoughts and prayers are with you. — Diane & Bill Shehane
I had the honor and privilege to shoot against and converse with Duane on three occasions, and also by phone[.] Duane was funny, witty, sincere, and a friend to everyone. He was one of the best 1000-yard shooters in the business. My heart and prayers go out to Pat, and all his family. — Donovan M.
I met Duane just four years ago. He welcomed me at Deep Creek and he and I spent many a morning before the shoots visiting about shooting, hunting, work and everything in between. People there always seemed to look up to Duane, and once you got to know him you understood why. I will never forget some of the shoots with him, he was an amazing shooter, several times while pulling his targets he would not even be on target with his sighters. But then the record target would go up and he would pull off a 98 or a 99, or even a 100. This did not just happen once either — Duane [was] simply an amazing guy! I helped him and Pat hook up their camper at the end of the August final shoot last year, shook his hand goodbye and he said “I will see ya in the spring young man”. Well that didn’t happen but I will always remember Duane and always be grateful that he was my friend. Happy shooting in Heaven Duane, and God Bless you Pat. — Wayne B.
Duane’s Dawn Patrol
Duane took this photo at the Deep Creek Range in March a few years back during one of his “Dawn Patrol” missions. Temperature? Duane said it was about 17 degrees! Now that’s dedication. Duane truly loved the shooting sports. He will be missed.
June 23rd, 2013
 In just two weeks, the 2013 NRA National Rifle and Pistol Championships commence at Camp Perry, Ohio. The big event kicks off with the Pistol SAFS on July 7th. There’s still time to register online for the National Championships. To sign up, visit www.NMEntry.com.
In response to increased interest in F-Class shooting, event organizers have even added a new discipline this year, the Mid-Range Rifle Championship with shooting at 300, 500, and 600 yards. (We wonder what chamberings F-Open competitors will choose for this new event — could this be the year of the Dasher at Perry?) For 2013, F-Class competitors can enter the NRA Mid-Range Rifle Championship and/or NRA Long Range Championship.
CLICK HERE for Camp Perry Championships Program
Birds-Eye View of Camp Perry Ranges
We know many of our worldwide readers may never have a chance to visit Camp Perry in person, but they are still interested in this historic facility on the shore of Lake Erie, near Port Clinton, Ohio. If you’ve always wanted to see what Camp Perry looks like, here are a series of “Birds-eye” photos taken from the Beach Tower.
Photos Courtesy Civilian Marksmanship Program.
June 23rd, 2013
 Gov. Rick Perry of Texas and Gov. Dennis Daugaard of South Dakota visited Connecticut last week. The two Governors hoped to recruit manufacturers to re-locate operations to their more business-friendly states. Connecticut firearms makers are high on the list of businesses both Perry and Daugaard seek to bring to their respective states. Gov. Perry wants Connecticut gunmakers to relocate to the Lone Star State, while Gov. Daugaard hopes South Dakota can attract these enterprises.
Larry Keane, Senior vice president and general counsel for the National Shooting Sports Foundation, provides a perspective on the recruiting effort. Keane suggests that economic growth in Connecticut is being stymied by official state policies. And Connecticut is no friend of the gun business, though firearms production has been one of Connecticut’s few growth industries in recent years:
The economic report card for the State of Connecticut is in and the results are not good.
The Bureau of Economic Analysis reports that Connecticut was last in the nation in economic growth in 2012, the only state where the combined value of goods and services produced (GDP) was lower than in 2011. In fact, total state GDP fell a quarter of a billion dollars last year, the same amount it fell in 2011.
On the heels of that report, the Manufacturing Alliance of Connecticut released the results of a survey that revealed Connecticut manufacturers predict a bleak outlook for the state’s economy and the health of their industries. The survey reported that a majority of the state’s manufacturers have been recruited to expand or relocate to another state and that they would consider doing so, most citing “government attitude” as the reason.
Connecticut’s firearms and components manufacturers have been the rare exception to the state’s dismal economic performance in recent years. Colt, Mossberg, Stag Arms, Ammunition Storage Components, to name four such companies, have added hundreds of jobs in recent years and, as a result, have contributed more in local and state taxes, even as other industries have cut back and moved facilities and jobs out of state.
We see a direct connection between the state’s nation-trailing GDP performance and the attitude of state government…. Gov. Perry understands all this. So he is coming to Connecticut. So too, is South Dakota Gov. Dennis Daugaard, who next week will also be recruiting these same manufacturers for his state. — Commentary by Larry Keane
June 22nd, 2013
 Run by Jeff Allen in Florida, CDI Precision Gunworks offers high-quality, mag-capable bottom metal for a wide variety of rifles and action types. The CDI bottom metal kits, priced at $209.00, feature an integrated trigger guard, mag-well, magazine release, and, of course, action-screw locations.
Most kits are designed for use with Accuracy International (AI) magazines, sold separately. These bottom metal kits are nicely finished and gunsmiths tell us that the fit is extremely good. CDI currently offers bottom metal kits for all these rifle/action types:
• Howa 1500 Short Action
• Howa 1500 Long Action
• FN-SPR Rifles (Also works on FN-PBR rifles)
• Remington 700 Short Action (.308, .300 WSM/7MM WSM, .223 mags work as well)
• Remington 700 Long Action (300 Win Mag, 338 Lapua, 338 CIP Mag box is available)
• Savage Short Action — (Both 4.275″ stagger-feed and newer 4.400″ Center feed)
• Savage Long Action (Call for Tech Data)
• Tikka T3 (Long and Short Action)
• Winchester Short Action (All Post 1964)
• Winchester Long Action, Short Box (.308 Win Length)
• Winchester Long Action Magnum Length (7MM Rem Mag and 300 Win Mag)
• Mauser 98 Large Ring action (.308 Win Mag box size)
Single-Shot Loading Blocks just $35.00
CDI has designed a single-shot loading block (SSLB) for use with CDI short action bottom metal kits. The SSLB lets you shoot your rifle in single-shot mode without a magazine. Simply place a round on the black cartridge-holder and close your bolt. This is a good set-up for load testing from the bench, or if you want to shoot very long bullets with a COAL greater than magazine length. CDI’s SSLB costs just $35.00 plus $5.00 shipping.
|
