2020 IBS 1K Nationals at Vapor Trail Range in Missouri
Report by Jim Bauer
“COVID Nationals” — That’s an unusual description for the IBS 1000-Yard Nationals, but it has been a very unusual year. On September 5th and 6th, 2020, Vapor Trail Valley Range held the IBS 1000-Yard National Benchrest competition. This year 63 shooters attended the event. While down from last year, that’s a good number considering the last-minute venue change. The IBS has worked hard this year to secure ranges where members can shoot and compete.
Vapor Trail Steps Up to Host 1K Nationals
When it appeared that holding the IBS 1K National event in North Carolina wasn’t going to be possible due to COVID-19 restrictions, Tom Jacobs, owner/operator of the Vapor Trail Valley Range in Spickard, Missouri stepped up. Along with Sara and Rory Jacobs, the Vapor Trail team accept the challenge of running a major National event. With only two months to prepare, the Jacobs hosted an outstanding event.
The precision with which this event was handled was impressive. Vapor Trail installed additional target frames to accommodate the larger attendance. A large TV screen streamed the scores, groups, relay winners and shooter positions as targets were measured. The Target Crew, managed by Sary and Rory Jacobs, had complete relay target changes done in less than five minutes. Tom Jacobs orchestrated the match from his newly constructed “Command Center” in the middle of the Firing Line and not once was there any confusion or time lost due to Shooter or Management Issues. Vapor Trail also supplied a BBQ lunch for all on Saturday and a ribeye steak lunch on Sunday. Nobody worried about going hungry.
This monitor showed immediate updates as the relays were scored. Jim Bauer notes: “it was really nice to see the scoring as it happened”.
Impressive Line-Up of 1000-Yard Competitors
The competition at this match was as tough as it gets. Competitors included IBS Long Range record-holders Mike Wilson, Tom Mousel, Bart Sauter, and Andy Ferguson. Past National Champions on hand included Glen Sterling Jr., Richard Schatz, Jason Walker, Glenn Hiett, and Carrol Lance. If you won a championship this year, you earned it. New IBS National 2-Gun 1000-Yard Champion Allan Carmichael can be very proud of his accomplishment this year.
Match Started with Good Conditions, But Then Got Tough on Day 2
Day one started off with good weather and mild wind conditions, allowing some impressive groups and scores. Then, in typical Vapor Trail fashion, the wind started to shape the results. At the end of Day One, two of the three Light Gun (LG) relays had been shot and one of three Heavy Gun (HG) relays were completed. The second day menu was to start with a HG relay, finish the Light, followed by the third and final Heavy Gun relay.
30 to 40 MPH winds at End of Day 2
On Day Two, the first HG session had relatively nice conditions, but then things got interesting. The south wind, a head wind at Vapor Trail, had a steady increase all day. By the time the Light Guns started to shoot again the wind was 15 mph plus with a switch from head on to a quarter in from the southwest. Groups and Scores opened up and the leader board had many unpredictable changes.
After the Light Guns were done, the Heavies stepped up for the final Relay sequence. The wind started to howl with peak velocities in the 30-40 mph range. If you were one of the unlucky Heavy Gun shooters in that final HG Relay on Day Two, it was tough. Over half of the shooters on the line DQ’d in a couple of target sequences (sub-sets of final relay). The shooters watched the wind flip over clay targets, laying on the berm, used in the sighter period. When all was said and done, due to the high winds, approximately 40% of the competitors DQ’d during the match at some point.
Top Competitors, left to right: Jason Boersma (HG Score + Overall), Glenn Hiett (HG Group), Allan Carmichael (2-Gun Champion), Jim Bauer (LG Group, Score, + Overall), and two of Jim’s grandsons.
When the match was over and the wind quit blowing us around, the winners were announced. For the prestigious 2-Gun title Allan Carmichael is our new IBS 1K Champion. Allan is from Carter Lake, Iowa. Allan has been an active shooter at Vapor Trail for years but wasn’t able to compete last year due to the Midwest flooding that happened last year. Not bad shooting for a guy that hasn’t been able to compete for almost 2 years. Allan used the same gun in both Light and Heavy classes. Allan campaigned a 6 Dasher built with a BAT SV action, Krieger barrel, and Jewell trigger in a stock that Alex Wheeler trued for him. Allan was shooting Berger 105gr VLDs with Varget and CCI 450s. Allan deserves credit — h did some great shooting under tough conditions for sure.
The Heavy Gun Overall Champion and HG Score winner was Jason Boersma from Sioux Falls, SD. Jason is a fierce competitor who has been winning since 2010. Jason is currently leading the IBS 1K Shooter of the Year race. Jason’s Heavy Gun is a .300 WSM with a Defiance action, 8″-wide forearm stock similar to a Maxi-Tracker, Krieger barrel, and Jewell trigger. He was shooting 215gr Berger Hybrids in Hornady .300 WSM brass filled with H4350 and Federal 210Ms.
Jason told us: “My Heavy Gun choice was pretty lucky, I brought both my HGs with me and on Thursday I shot them both and the WSM shot much better than my 6.5 Outlaw HG, so I decided to go with it. That’s why on the equipment list it has my 6.5 written down. I just finished my .300 WSM one week before the match and wasn’t even sure about bringing it along, but I’m glad I did. In Light Gun I was just trying to focus on not making a mistake and hope the conditions held each time. On Sunday the winds got pretty bad and strong gusts and I was just trying to get all the shots off quickly and hope they stayed on paper. The strong winds caused many DQs, but overall it was a great Nationals and a great time spent shooting with friends. You are only as good as the people you shoot against and the best were there that weekend.”
Jason’s Light Gun features a Borden action, Bix ‘N Andy trigger, and a stock he crafted himself. His LG cartridge was a wildcat, the 6.5 Outlaw. Jason said the case is essentially a 6.5×47 Lapua AI. The velocity is 2850 fps using 140gr Berger Hybrids, H4350, and CCI BR4 primers.
Jim Bauer was was Light Gun Score, Group, and Overall champion [Editor: Mighty impressive trifecta Jim!] Jim’s rifle featured a BAT B action, Krieger barrel, Bix ‘N Andy trigger. The stock is a modified ST-1000 with truing and modifications by Gordy Gritters who has been Jim and Sally’s gunsmith for 15+ years. Jim’s cartridge is the 6 Dasher loaded with Varget powder and 103gr Vapor Trail bullets. Notably Jim was using CCI 550 Magnum PISTOL primers (yes FIVE-Fifty). Jim says some of the Deep Creek, Montana 1K shooters have also tried these CCI 550 pistol primers with success.
Glen Hiett was the Heavy Gun Group champion this year. A great competitor, Glen was the 2-Gun champion at Hawk’s Ridge last year AND he was also the 2019 IBS 1K Shooter of the Year. Remarkably, Hiett earned those major achievements in his rookie year. I think we are going to be seeing a lot more of Glenn in the winner’s circle. Glenn ran the 6 BRA cartridge (6mm BR improved). His rifle featured a BAT B action, Jewell trigger, Brux barrel, and Alex Sitman stock. He was using Vapor Trail 103gr bullets with Alliant Reloder 15 powder and CCI 450s.
Ladies Champion Donna Matthews with Vapor Trail Range Owner Tom Jacobs (left).
The 2020 Ladies Champion is Donna Matthews from North Carolina. Donna was the Ladies Champion in 2019 as well. Along with her husband David, they are the IBS goodwill ambassadors.
Praise and Thanks for Vapor Trail Range and IBS Sponsors
There are lots of stories to be told from this year’s 1K Nationals. As confirmed in AccurateShooter Forum threads, the match ran flawlessly. Everyone was thankful that we had a place to shoot a game that we love. The food, the friendships, the camaraderie, all made for a fun, inviting environment. We thank the Jacobs family clan for hosting us. Give credit also to Mike McBride for the scoring program that he created for the 600-yard discipline and the modified version he built for this event. Thanks to all within the IBS who worked hard so that we could still hold this event in this Pandemic year.
We want to thank all of our sponsors that made the match and ample Prize Table possible. We certainly realize that 2020 has been a challenging year. We thank the guys from Hornady — Craig Anderson, John Potratz, Justin Morrow, Trampas Kluender, and Chad Donscheski. They have supported Vapor Trail Range for years and their contributions are appreciated. We also want to thank AMP annealing, Bench Source, 21st Century Shooting, Krieger Barrels, Hawkhill, Bart’s Bullets, and SEB Rests.
Benchrest and F-Class shooters know that you need a very good rear bag to achieve optimal (and repeatable) accuracy with your rifle. The rear sandbag does more than just support the weight of the rifle in the rear. It also aligns the stock with the front rest, absorbs vibration/shock, and perhaps most importantly, guides the rearward travel of the stock during the recoil cycle.
A premium bag will be stable from shot to shot, not move on recoil, and also be a good match to the angles and width of the keel (bottom) of your stock. Modern rear sandbags also employ various types of synthetics on the contact surfaces. The idea is to reduce friction which still providing a stable “grip” on the stock.
We’ve learned that our friend Sebastian Lambang, inventor of SEB coaxial rests, has come up with an improved, second-generation Bigfoot Rear bag. The design looks very well thought-out and the craftsmanship is excellent. Seb welcomes comments on his Facebook Page. These will be available soon from SEB dealers worldwide.
Seb explains: “Here is the new/premium SEB Bigfoot Rear Bag. The photos show our Prototype bag model shown with nylon seat belt material on the ears.” Note that the bags sit perfectly flat — there is no bulge on the bottom even though the bags are “packed to the brim with sand”.
Dimensions: Standard spacings between ears: 3/8″, 1/2″, 5/8″, 3/4″, and 1″; standard height: 4″.
Customizing: Other spacing, bag height, for right- or left-handed available on request.
Accessories: The SEB doughnut (bag base/surround unit) is also available (sold separately).
Here is gunsmith Richard King, with his updated Martini Mark III smallbore rifle.
This is the kind of family-friendly, “feel-good” story we like. A few years back, Texan Richard King created a rimfire benchrest rifle using a classic Martini Mark III smallbore action. He fitted the gun with a new flat, wide forearm and a new buttstock, allowing the gun to sit steady on the bags and track smoothly. The narrow action was also fitted with a cantilevered top rail to hold a high-magnification scope.
Here is Vicki King, with Martini Mark III and her trophy.
But here’s the best part. Back in 2014, Richard provided this updated classic to his wife Vicki, who proceeded to win a rimfire benchrest match (Vintage class) with the old Martini. Richard reports: “Here is my lovely wife with her High Overall Vintage trophy. That is a Martini Mark III that I re-stocked in walnut for 50-yard, .22-caliber benchrest matches. It’s great to have her shooting with me again.”
Bravo Richard — kudos to you AND to your lovely bride. It’s great to see a couple shooting together. It’s also great to see a classic rifle brought back to the winner’s circle with some inspired stock-work, new optics mount, and other smart upgrades. Old rifles never die… at least if they find their way to a great smith like Richard King.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
⏺ Great value at $279.99 with CODE 16617906 — Safe weighs 179 lbs.
Here is a great deal for a secondary safe that you might use in a workshop, bedroom, vacation property, or even an RV. This Union Safe Co. 10-Gun safe compares with Stack-On safes costing up to $560.00. Sold by Harbor Freight, this safe is rated for 10 long guns and also has a top shelf for handguns and valuables. NOTE: This safe appears for $339.99 on the Harbor Freight website. To get the $279.99 Sale price, use the Sale Code Number 16617906 when you add the safe to your shopping cart. You can also use the same Sale Code for in-store purchases. Safe Dimensions: 59″ H x 21″ W X 14″ D.
⏺ Get good shooting M1 Garand with New Criterion Barrel and New Stock
The CMP now offers a “partially refurbished” M1 Garand for $650.00. The CMP Special Rack Grade (.30-06) M1 Garand features a refinished M1 receiver, a NEW production Criterion barrel, NEW production American Walnut stock and handguards, and NEW web sling. The receiver is the only original part of the rifle that has been refinished. The CMP notes that the receiver will have heavy pitting above the wood line. If you can live with that cosmetic flaw, this is a good choice for those who want to shoot M1 Garand matches. IMPORTANT: To purchase a CMP M1 Garand, a buyer must be an adult U.S. citizen who is a member of a CMP-affiliated club. ORDERING Information HERE.
⏺ Versatile, affordable optic for PRS and Varminting
If we needed a SFP scope with MOA reticle for varmint or fun match duties, this 5-24x50mm Vortex Viper would be one of our leading choices. With a magnification range perfect for varminting, this optic offers good glass, nice controls, and a great warranty — all at an affordable price. And right now you can Save $280 on this Vortex Viper at EuroOptic. This scope features glass-etched EBR-1 reticle in the second focal plane, XD Lens, 30mm main tube, tactical-style turrets, and CRS zero stop.
4. Midsouth — Norma .223 Remington Brass, $99.99 for 250
⏺ Impressive deal on very high quality .223 Rem brass
After Lapua, Norma makes some of the best brass you can buy. And here’s a chance to get a big supply of .223 Rem brass for your High Power or varmint rifle. This 223 Remington brass has very tight tolerances, holds up well to multiple reloads. We have seen very good accuracy with this brass with both light and heavy .224-caliber bullets. The price — $99.99 for 250 cases, works out to $0.39 per case. You can pay up to $0.70 per case for some other premium .223 Rem brass.
⏺ Excellent hard case, $50 savings, great for air travel
This is one of the best large hardshell rifle cases on the market. The Pelican Vault V800 compares well to other hard cases costing up to $350.00 but right now it is just $149.96 at MidwayUSA. Choose Desert Tan or Black. This case will hold two large match rifles securely. It features five layers of customizable foam, along with six (6) push-button latches. This same V800 53″ case sells elsewhere for $219.00, and is normally $199.95 at MidwayUSA. With this deal you save $50.00! Competitors headed to the F-Class Nationals in Raton, NM at the end of the month may want to grab one of these big 53″ cases.
6. Brownells — KRG Bravo Chassis Rem 700, $324.99 with Code
⏺ Versatile internal frame stock for PRS or hunting — tan, black, or green
The Kinetic Research Group (KRG) Rem 700 Bravo Chassis is a good dual-purpose choice for PRS and hunting. There is an internal aluminum frame with polymer exterior in Flat Dark Earth, Sako Green, or black. The stock fits Rem 700 and Rem Clone actions, accepts AICS-pattern mags, and is M-LOK compatible. The 2.9-lb KRG Bravo chassis features adjustable cheek riser and length-of-pull, built-in thumb shelf, plus quick-detach sling-swivel and bipod mounts. The KRG Bravo stock costs $349.99 at Brownells. You can also get $25 Off with Brownells code VSE, lowering the net cost to $324.99.
7. Amazon — Teslong Borescope $44.99 or Rigid Version $79.99
⏺ Teslong borescopes are game-changers — true “must-have” tool
The Teslong digital borescope has been a huge success. This compact, electro-optical, cable-type borescope outputs sharp, high-resolution images and VIDEO to desktop computers and laptops, and many tablets. Check out our Full Teslong Review complete with inside-the-barrel videos. Get the basic version for $44.99 on Amazon or the rigid version Teslong Borescope for $79.99. If you scope your barrels often, you may prefer the rigid version which is easy to insert and rotate.
8. Midsouth — Tipton Gun Butler, $19.49
⏺ Very useful, particularly for regular cleaning, great price
Here’s a handy, portable gun caddy that works well for rifle maintenance chores at home or at the range. Right now the Tipton Gun Butler is marked down to $19.49. The Gun Butler offers a convenient platform for cleaning your gun or doing tasks such as scope mounting. Two removable forks/cradles hold a gun securely in place, while compartments and slots hold solvents, jags, brushes, mops, and tools. The Gun Butler features a convenient carrying handle, and slip-resistant rubber feet.
9. MidwayUSA — Remington Roll-Up Mat Cleaning Kit, $11.77
⏺ Amazing deal — very complete tool set, and great gift item
This is a great portable gun cleaning kit. It’s now a steal at just $11.77, 68% off the regular price. This kit contains 9 caliber-specific bore brushes, 5 various-sized bore mops, patch pullers, a 3-piece cleaning rod, plus a pair of utility cleaning brushes. Heck just all the brushes and mops are worth more than the $11.77 price. This kit also makes a great gift for your shooting buddies or family members who enjoy guns.
2020 has been a pretty rotten year so far — with the Pandemic, shutdowns, riots, and, yes, cancellation of major shooting tournaments, including the big summer National Matches at Camp Perry.
But, not daunted, the CMP organized a series of shooting matches around the country, called the Home Range Appreciation Series. Over 1200 Rifle and pistol competitors shot Home Range matches in 32 states this year. In total, 11 smallbore events, 33 air rifle, 9 GSMM rifle, 13 Highpower Rifle Aggregate, 2 pistol and 4 Rimfire Sporter rifle events were fired in 32 states. Nearly 1,500 entries were recorded throughout the events, with competitors from 43 states.
Open to both adult and junior athletes, the Home Range Appreciation Series events were fired in local club matches and scored by the CMP to be compared against overall scores from participating marksmen around the nation. Matches included the White Oak 1600 Rifle Aggregate, a 200-Yard Reduced Course 800 Rifle Aggregate, a Garand/Springfield/Vintage/Modern Military Rifle Match, Rimfire Sporter Rifle, CMP Pistol 2700 (featuring .22 Rimfire, Center Fire and 45 Caliber pistols), Smallbore 3×20, Smallbore Prone 3200, and air rifle 3×20 and 60-Shot matches.
The CMP conducted a Virtual Awards Ceremony on Friday, October 2, 2020, to honor the top competitors in various discpline. A drawing for all sponsor-donated items also took place during the Virtual Awards Ceremony. You can watch this virtual awards ceremony on YouTube:
The CMP thanks all participants, volunteers, clubs and others who helped to make this inaugural event a true success. To see the top performers, CLICK HERE for full list of Home Range Match Results.
We’re in the thick of hunting season now, so we’re featuring an impressive new hunting rig from Springfield Armory. The new Model 2020 Waypoint rifles feature advanced carbon-wrapped barrels*, TriggerTech triggers, and carbon-fiber, hand-painted camo stocks. The actions are pretty impressive too — with precision machining, enlarged ejection port, and integral recoil lug. These Waypoint rifles rival full-custom hunting rigs, yet are reasonably affordable. Starting price is $1699.00 with stainless barrel, while the deluxe model with carbon-wrapped barrel and adjustable cheekpiece is still under $2,400.00.
Handsome Hand-Painted Carbon-Fiber Stocks
Minimum gun weight with carbon-wrapped barrel and fixed cheek is just 6.6 pounds.
All Model 2020 Waypoint rifles feature strong, light-weight, carbon-fiber-reinforced stocks with hand-painted camouflage finishes. Springfield Armory worked with AG Composites to develop these handsome stocks. You could easily pay $700-$800 just for an equivalent camo-painted stock from McMillan or Manners Composite Stocks.
Four Chambering Choices
The Model 2020 Waypoint is offered in four popular chamberings: 6mm Creedmoor, 6.5 Creedmoor, 6.5 PRC, and .308 Winchester. Those are all desirable options. However, because this is a hunting rifle, we would also like to see a 7mm option, and a larger .30-caliber option. At least the barrel twist rates will allow modern, high-BC bullets: 1:7.5″ for the 6mm Creedmoor, 1:8″ for the 6.5 Creedmoor, and 1:10″ for the .308 Win. All barrels are threaded 5/8-24 for the included SA Radial Muzzle Brake.
TriggerTech Adjustable Trigger and Fast Lock Time
We were pleased to see the Model 2020 Waypoint comes with a very good TriggerTech trigger that easily adjusts from 2.5 to 5.0 pounds. This trigger, as combined with a modern fire control system, achieves a very good 19 millisecond lock time — that rivals some custom benchrest actions, and is up to 45% faster than some other factory actions. FYI, “lock time” is measured from the break of the trigger until the firing pin strikes the primer.
Modern Coated Action with Big Ejection Port — Takes AICS-Compatible Mags
Springfield Armory did a nice job with the action. There is a large ejection port and EDM-crafted raceways. The fluted bolt and the action body are coated for corrosion resistance and smooth operation. Additionally, the bolt features dual cocking cams for ease of operation and tool-less disassembly for maintenance.
Factory 3/4-MOA Accuracy Guarantee
Springfield offers an impressive 0.75 MOA three-shot accuracy guarantee with “with quality match-grade factory ammunition, in the hands of a skilled shooter.” That is actually pretty impressive for a hunting rifle that weighs in under 7 pounds before options (carbon bbl version). You could spent a LOT more on a custom rig and not do much better accuracy wise.
Bottom Line — How Does It Feel and How Does It Shoot?
Respected gun writer and hunter Wayne Van Zwoll tested a carbon-barrel Model 2020 Waypoint for Hunting Digital Magazine. He was impressed with the feel of the rifle, the quality of the components, the crispness of the trigger, the smooth mag-feeding, and the demonstrated accuracy:
“This rifle balances well. Running this rifle is a delight! It slurps cartridges seamlessly from the box and is easy to top-feed with single rounds. The magazine is a cinch to release and easily inserted. Springfield Armory’s Waypoint Model 2020 is notable for its relatively modest price — under $2,400 for even the most expensive version, and a starting price of $1,699 — [and] the quality of its parts and workmanship.
Accuracy — My first three shots, after bore-sighting and two to zero, cut a 0.62″ knot. I printed some more groups, which measured .63″ and .70″. Such accuracy from a rifle that, stripped, scales under 6¾ pounds should please any shooter! It’s also a credit to Hornady’s excellent ammunition.
In sum, the Waypoint offers features and performance now expected of top-rung multi-purpose rifles, without bleeding budgets. It should impress hunters as well as shooters scrambling in cross-terrain rifle competition[.] The first new Springfield Armory bolt rifle in a century has impressed me!”
* The base Model 2020 Waypoint has a fluted stainless barrel. The carbon-wrapped barrel is an extra-cost option, as is the adjustable cheekpiece.
When neck-turning cases, it’s a good idea to extend the cut slightly below the neck-shoulder junction. This helps keep neck tension more uniform after repeated firings, by preventing a build-up of brass where the neck meets the shoulder. One of our Forum members, Craig from Ireland, a self-declared “neck-turning novice”, was having some problems turning brass for his 20 Tactical cases. He was correctly attempting to continue the cut slightly past the neck-shoulder junction, but he was concerned that brass was being removed too far down the shoulder.
Craig writes: “Everywhere I have read about neck turning, [it says] you need to cut slightly into the neck/shoulder junction to stop doughnutting. I completely understand this but I cant seem to get my neck-turning tool set-up to just touch the neck/shoulder junction. It either just doesn’t touch [the shoulder] or cuts nearly the whole shoulder and that just looks very messy. No matter how I adjust the mandrel to set how far down the neck it cuts, it either doesn’t touch it or it cuts far too much. I think it may relate to the bevel on the cutter in my neck-turning tool…”
Looking at Craig’s pictures, we’d agree that he didn’t need to cut so far down into the shoulder. There is a simple solution for this situation. Craig is using a neck-turning tool with a rather shallow cutter bevel angle. This 20-degree angle is set up as “universal geometry” that will work with any shoulder angle. Unfortunately, as you work the cutter down the neck, a shallow angled-cutter tip such as this will remove brass fairly far down. You only want to extend the cut about 1/32 of an inch past the neck-shoulder junction. This is enough to eliminate brass build-up at the base of the neck that can cause doughnuts to form.
The answer here is simply to use a cutter tip with a wider angle — 30 to 40 degrees. The cutter for the K&M neck-turning tool (above) has a shorter bevel that better matches a 30° shoulder. There is also a 40° tip available. PMA Tool and 21st Century Shooting also offer carbide cutters with a variety of bevel angles to exactly match your case shoulder angle*. WalkerTexasRanger reports: “I went to a 40-degree cutter head just to address this same issue, and I have been much happier with the results. The 40-degree heads are available from Sinclair Int’l for $15 or so.” Forum Member CBonner concurs: “I had the same problem with my 7WSM… The 40-degree cutter was the answer.” Below is Sinclair’s 40° Cutter for its NT-series neck-turning tools. Item NT3140, this 40° Cutter sells for $14.99. For the same price, Sinclair also sells the conventional 30° Cutter, item NT3100.
Al Nyhus has another clever solution: “The best way I’ve found to get around this problem is to get an extra shell holder and face it off .020-.025 and then run the cases into the sizing die. This will push the shoulder back .020-.025. Then you neck turn down to the ‘new’ neck/shoulder junction and simply stop there. Fireforming the cases by seating the bullets hard into the lands will blow the shoulder forward and the extra neck length you turned by having the shoulder set back will now be blended perfectly into the shoulder. The results are a case that perfectly fits the chamber and zero donuts.”
* 21st Century sells carbide cutters in: 15, 17, 20, 21.5, 23, 25, 28, 30, 35, 40, and 46 degrees. PMA Tool sells carbide cutters in: 17.5, 20, 21.5, 23, 25, 28, 30, and 40 degrees, plus special short-neck cutters.
Forum member Nodak7mm has discovered an ideal way to store your rifle cleaning rods in your garage or loading room. Using inexpensive Berkley Horizontal Fishing Rod Racks, Nodak7mm has secured a half-dozen Dewey rods on the back of a door. You could also mount the racks along a wall or on the side of a storage cabinet. This installation takes up minimal space and the Berkley Racks cost just $11.96 at Amazon (select “6 Rod Rack”) or $16.50 per set at Walmart. If you prefer wood, Amazon also sells a pine 6-rod wall rack for $22.45.
Nodak7mm explains: “I was moving some fishing poles around and ended up with an extra pair of Fishing Rod wall racks. I said to myself, ‘I bet this would hold my Dewey cleaning rods’. I mounted the pair on the inside of a closet door in my man cave and put my cleaning rods in it. It works like a charm and is far cheaper than a specially-made rack that only lets the rods hang. One can even slam the door with the rods mounted and they stay put. This rod rack set… is made by a nationally recognized name and does a great job of holding the cleaning rods securely and safely.” These are inexpensive and are easy to mount to a door or wood cabinet.
Stow Your Cleaning Rods on Your Gun Safe
Another option is to make a rod set with a magnetic backing strip. This can be affixed to the sides of your gun safe or steel storage cabinet. Here is a home-made, magnet-affixed cleaning rod holder made by Forum Member “BobM”. This smart installation works great. CLICK HERE for more information.
Sturm, Ruger & Company, Inc. (Ruger) announced on 10/2/2020 that its offer to purchase substantially all of the Marlin Firearms assets was accepted by Remington Outdoor Company, Inc. and approved by the United States Bankruptcy Court for the Northern District of Alabama. Ruger will pay the $30 million purchase price from cash on hand at the time of closing, which is expected to occur in October.
“The value of Marlin and its 150-year legacy was too great of an opportunity for us to pass up,” said Ruger President and CEO Chris Killoy. “The brand aligns perfectly with ours and the Marlin product portfolio will help us widen our already diverse product offerings.”
The transaction is exclusively for the Marlin Firearms assets. Remington firearms, ammunition, other Remington Outdoor brands, and all facilities and real estate are excluded from the Ruger purchase. Once the purchase is completed, Ruger will begin the process of relocating the Marlin Firearms assets to existing Ruger manufacturing facilities.
“The important thing for consumers, retailers and distributors to know at this point in time,” continued Killoy, “is that the Marlin brand and its great products will live on. Long Live the Lever Gun.”
“Marlin Firearms was founded in 1870, some 144 years ago, by Mr. John Mahlon Marlin. As such, Marlin rifles for generations carried ‘JM’ roll marks on their barrels to designate this homage. Marlin had cut his teeth in Samuel Colt’s factory making revolvers and pistols during the Civil War in Hartford, Connecticut. Then, he broke out on his own, starting a small shop in nearby New Haven.
The company specialized in lever action rifles, such as the M1891, which was updated as the 1893, then the Model 39, and still exists today as the Model 336. After Mr. Marlin died in the early 1900s, the company went from being family-owned to being a corporation, which made machine guns for the Army during World War 1, merged with Hopkins and Allen, then in 1924 went out of business.
It was then that the Kenna family bought what was left of the company for $100 and, for all but a decade, a member of the Kenna family remained the president of the company for the next 83 years. During that time, Marlin registered hundreds of patents including on side ejection lever actions, Micro-Groove rifling, the T-900 Fire Control System, and others.”
More recently, in the year 2000, Marlin acquired Harrington and Richardson (H&R), maker of break-action shotguns and rifles. Then in 2007 Remington bought out Marlin, including H&R.
Gander Outdoors in Kenosha, WI — reader-submitted photo on GMToday.com
There is major ammunition shortage right throughout the nation. The unrest and riots in urban areas along with left-wing calls to “defund the police” have caused millions of Americans to be concerned about safety, so they are buying ammo wherever they can find it, online and in stores. Another reason ammo demand is exceeding supply is that 2020 has seen record numbers of first-time gun owners buying acquired rifles, pistols, and shotguns, primarily for self-defense. According to the NSSF, gun sales are up 95% in the first half of 2020 compared to Jan-June 2019. Even more remarkable, the NSSF says ammo sales are up 139% compared to the same time period in 2019. That’s a massive increase.
One ammunition manufacturer, Arizona-based Ammo Inc. has revealed that it has $80 million in unfilled ammo orders. “We’re working right now seven days a week, 24 hours a day in all the manufacturing plants”, Ammo Incorporated CEO Fred Wagenhals told AZFamily.com.
“We just bought 2.8 million dollars worth of machinery and equipment last week to increase our production and increase our volume”, Wagenhals added.
According to GunsAmerica Digest, “Wagenhals attributed the jump in demand to various factors, including COVID-19, the upcoming presidential election, and widespread civil unrest[.]” Wagenhals noted: “As you’ve seen in a lot of cities, the looting and the burning, and I think people are just scared.”
Mark Oliva, NSSF Director of Public Affairs, told GunsAmerica that the spike in demand for ammo mirrors that of firearms, with ammo sales skyrocketing:
“The sale on ammunition goes hand-in-glove with the sale of firearms. NSSF estimates there are more than 5 million people who bought a gun for the first time this year and we’ve recorded more than 13.8 million background checks for the sale of a gun this year. That tops figures for all of 2019 in just the first eight months of 2020. That’s caused an unprecedented demand in the marketplace and we’re seeing this happen everywhere.”
“Ammunition makers are working as quickly as possibly to meet this demand,” Oliva continued. “We’ve seen spikes before and we’ve seen sustained period of demand. This year, though, is unlike any before.”
Ammo Inc.’s STREAK Ammo — Tracers without Heat
Ammo Inc. produces a unique type of STREAK ammo that delivers a tracer-like light trail when fired. Through patented technology, a photo-luminescent coating is applied to the base of the bullet. This is “activated” on firing, allowing the shooter to see the projectile’s path toward its target. STREAK rounds are NON-incendiary. They do not generate heat so they are safe to use in environments where tracers are prohibited or could be a fire hazard. Ammo Inc. says these STREAK bullets are “game-changing” for indoor range use and low-light shooting.
When neck-turning cases, it’s a good idea to extend the cut slightly below the neck-shoulder junction. This helps keep neck tension more uniform after repeated firings, by preventing a build-up of brass where the neck meets the shoulder. One of our Forum members, Craig from Ireland, a self-declared “neck-turning novice”, was having some problems turning brass for his 20 Tactical cases. He was correctly attempting to continue the cut slightly past the neck-shoulder junction, but he was concerned that brass was being removed too far down the shoulder.
Forum member Nodak7mm has discovered an ideal way to store your rifle cleaning rods in your garage or loading room. Using inexpensive 
