At the request of Forum members, we are reproducing this helpful article by gunsmith and Hall-of-Fame benchrest shooter Thomas “Speedy” Gonzalez
How to Reduce Vertical in Your Shot Groups
One of our Shooter’s Forum members recently built a new benchrest rifle. He was concerned because his groups were stringing vertically. This is a common problem that all precision shooters will face sooner or later. In addition to ammo inconsistencies, many other factors can cause vertical stringing. Accordingly, it’s important that you analyze your gun handling and bench set-up systematically.
Hall of Fame benchrest Shooter Speedy Gonzalez has written a helpful article that explains how to eliminate mechanical and gun-handling problems that cause vertical spread in your groups. Speedy’s article addresses both the human and the hardware factors that cause vertical. CLICK HERE to read the full article. Here are a few of Speedy’s tips:
• Front Bag Tension — Vertical can happen if the front sand bag grips the fore-arm too tightly. If…the fore-arm feels like it is stuck in the bag, then the front bag’s grip is too tight. Your rifle should move in evenly and smoothly in the sand bags, not jerk or chatter when you pull the gun back by hand.
• Sandbag Fill — A front sandbag that is too hard can induce vertical. Personally, I’ve have never had a rifle that will shoot consistently with a rock-hard front sandbag. It always causes vertical or other unexplained shots.
• Stock Recoil — Free-recoil-style shooters should be sure their rifle hits their shoulder squarely on recoil, not on the edge of their shoulder or the side of their arm. If you shoulder your gun, you need to be consistent. You can get vertical if your bench technique is not the same every shot. One common problem is putting your shoulder against the stock for one shot and not the next.
• Front Rest Wobble — You will get vertical if the top section of the front rest is loose. Unfortunately, a lot of rests have movement even when you tighten them as much as you can. This can cause unexplained shots.
• Stock Flex — Some stocks are very flexible. This can cause vertical. There are ways to stiffen stocks, but sometimes replacement is the best answer.
• Rifle Angle — If the gun is not level, but rather angles down at muzzle end, the rifle will recoil up at butt-end, causing vertical. You may need to try different rear bags to get the set-up right.
• Unbalanced Rifle — If the rifle is not balanced, it does not recoil straight, and it will jump in the bags. If the rifle is built properly this will not happen. Clay Spencer calls this “recoil balancing”, and he uses dual scales (front and rear) to ensure the rifle recoils properly.
• Firing Pin — A number of firing-pin issues can cause vertical. First, a firing pin spring that is either too weak or too strong will induce vertical problems. If you think this is the problem change springs and see what happens. Second, a firing pin that is not seated correctly in the bolt (in the cocked position) will cause poor ignition. Take the bolt out of rifle and look in the firing pin hole. If you cannot see the entire end of firing pin it has come out of the hole. Lastly, a firing pin dragging in bolt or shroud can cause vertical. Listen to the sound when you dry fire. If you don’t hear the same sound each shot, something is wrong.
• Be Consistent — You can get vertical if your bench technique is not the same every shot. One common problem is putting your shoulder against the stock for one shot and not the next.
• Head Position — Learn to keep your head down and follow-through after each shot. Stay relaxed and hold your position after breaking the shot.
• Last Shot Laziness — If the 5th shot is a regular problem, you may be guilty of what I call “wishing the last shot in”. This is a very common mistake. We just aim, pull the trigger, and do not worry about the wind flags. Note that in the photo below, the 5th shot was the highest in the group–probably because of fatigue or lack of concentration.
Q: What is the most popular gun book ever published?
A: That distinction goes to the Shooter’s Bible, which has sold over 7 MILLION copies since it was first published over 80 years ago.
Released last month (October 2018), the 110th Edition of this respected resource is bigger and better than ever. This latest Shooter’s Bible boasts 608 pages with 275 color photos and more than 1000 black-and-white photos. The new 110th Edition features many new firearms as well as new optics.
Published annually for more than eighty years, the Shooter’s Bible is perhaps the most comprehensive reference guide for firearms and their specifications. The publishers claim that “nearly every firearms manufacturer in the world” is included. The 110th Edition also contains new and/or enhanced sections on ammunition, optics, and accessories, along with updated handgun and rifle ballistic tables. There are also extensive charts of currently available hunting and match bullets for hand-loaders.
While many shooters are now using the internet to get reloading data and equipment specifications, the Shooter’s Bible remains a valuable resource with a great legacy. As one recent Shooter’s Bible purchaser explains: “While it’s true that much of the information contained in the Shooter’s Bible can be found on the Internet, there are many of us who would first rather relax in our easy chair and page through the book at our leisure. If you find an item that catches your fancy, you can then follow up by going to their Web site.”
Another buyer observed: “This latest edition is proof that, even with all the attacks on our 2nd Amendment right over the years, the industry has persevered and grown. I hope the day never comes when there will no longer be a reason to publish the Shooter’s Bible.”
The U.S. Army Marksmanship Unit (USAMU) regularly releases a reloading “how-to” article on the USAMU Facebook page. Here’s a helpful USAMU guide on removing military primer pocket crimps. If you ever use surplus military brass, you really should this article. It contains vital information “learned the hard way”. The writer has tried many different options for removing/swaging out crimps. He weighs the pros and cons of various methods and provides some advice that will save you time and headaches. This article was the second in a 3-part series. Visit the USAMU Facebook page regularly for other informative articles on reloading methods.
A common question, and important issue with US GI surplus 5.56 brass is “what to do with the primer crimp?” Our Handloading Shop does not prime/re-prime GI 5.56 brass, as we receive it in virgin state (primed) and don’t reload it. However, our staff has extensive private experience handloading GI brass in our own competitive shooting careers, and have several tips to offer.
Once the brass is full-length sized and decapped, the staked-in ring of displaced metal from the primer crimp remains, and hinders re-priming. Some swaging tools exist to swage out this ring, allowing free access to the primer pocket. Some are stand-alone products, and some are reloading-press mounted. Early in this writer’s High Power career, he used the common press-mounted kit several times, with less than stellar results.
Setting Up Swaging Tools
Surplus brass tends to come from mixed lots, and primer crimp varies from very mild to strong. Also, primer pocket dimensions vary. So, setting up this “one size fits most” tool involves trying to find a happy medium for a selection of different types of brass in your particular lot. Some are over-swaged, some under-swaged, and some are “Just Right.” Overall, it was a time-consuming and sub-optimal process, in this writer’s experience.
Cutting Out the Crimp Ring with a Chamfer Tool
[After trying swaging tools] this writer evolved to using the ubiquitous Wilson/RCBS/Other brands chamfer and deburring tool to cut out only the displaced crimp ring at the top of the primer pocket. One caution: DON’T OVER-DO IT! Just a little practice will let the handloader develop a “feel” for the right degree of chamfer that permits easy re-priming without removing so much metal that primer edges start to flow under pressure. For this writer, it was three half-turns of the tool in the primer pocket, with medium pressure.
Here, as with all bulk reloading operations, mechanization is our friend. A popular reloading supply house has developed an inexpensive adaptor that houses the chamfer/deburr tool (retained by an allen screw) and allows mounting in a hand drill or drill press. This speeds the operation significantly, as does use of one of the popular Case Preparation Stations that feature multiple powered operations. (Say good-bye to carpal tunnel syndrome and arthritis!)
One advantage of chamfering the primer pockets lightly to remove remnants of primer crimp, vs. swaging, is that primer pockets are not loosened in this process. US GI (usually LC) NATO 5.56 brass has a great reputation for longevity due to the superior hardness of the case head vs. some softer brands of commercial brass. This means the brass will stand up well to multiple full-pressure loads without loosening primer pockets, and the chamfering method helps support this benefit.
Powered Case Prep Centers — What to Look For
A word of advice (often learned the hard way) — think carefully before jumping on the “latest/greatest” case prep center. One with a proven, long-time track record of durability and excellent customer support has a lot going for it, vs. the flashy “new kid on the block.” Analyze the functions each case prep center can support simultaneously — i.e., can it chamfer, deburr and clean primer pockets all at the same time, without having to re-configure?
Do the tool-heads that come with it look truly functional and durable? If not, can they be easily replaced with proven or more-needed versions, such as a VLD chamfer tool, or a solid/textured primer pocket cleaner rather than a less-durable wire-brush type?
Tips for Priming with Progressive Presses
When re-priming, a couple of factors are worth noting. When re-priming using either single-stage presses, hand tools, or bench-mounted tools (such as the RCBS bench-mounted priming tool), precise alignment of the primer pocket entrance with the primer is easily achieved, and priming goes very smoothly. When using certain progressive presses, due to the tolerances involved in shell-heads, etc., one may occasionally encounter a primer that isn’t quite perfectly aligned with the primer pocket.
If resistance is felt when attempting to re-prime, DO NOT attempt to force the primer in — doing so can be dangerous! Rather, just exert SLIGHT upward pressure to keep the primer in contact with the case-head, and with the support hand, move the case back/forth a trifle. The primer will drop into alignment with the primer pocket, and then prime as usual. After priming, check each seated primer by feel. Ensure it is below flush with the case head (cleaning primer pockets helps here), and that there are no snags, burrs or deformed primers.
More Info on Primer Pocket Swaging
For more information about removing military crimps in primer pockets, we recommend you read Get the Crimp Out on the Squibloads Gun Thoughts Blog. This is a detailed, well-illustrated article that shows how to use various primer pocket reamers/cutters. It also has a very extensive discussion of swaging using CH4D, RCBS, and Dillon tools. The Squibloads author had much better luck with swaging tools than did the USAMU’s writer — so if you are considering swaging, definitely read the Squibloads article.
The illustration of primer pocket types is from the Squibloads Blog Article, Get the Crimp Out.
Today is October 31st, Halloween (originally “All Hallows Eve”). That means it’s pumpkin time. Just how much fun can you have with pumpkins? Watch these two videos and find out. In the first video, the RatedRR team sends a few orange gourds to pumpkin heaven using Det Cord, C4, and binary explosives. The sequence starting at the 2:00 minute mark in the first video is truly amazing. WARNING: DO NOT TRY THIS AT HOME!
Watch Pumpkin Blasting with Explosives
In the next video, a pumpkin carved as a Death Star serves as the target for a .50 caliber rifle (looks like a Barrett M82 .50 BMG). As you may guess, the pumpkin Death Star suffers the same fate as the Hollywood version in Star Wars. NOTE: At the 0:42 mark in the video, a graphic displays “30,000 FPS”. That’s the high-speed camera’s frame-per-second rate, NOT the projectile velocity in feet-per-second.
Watch .50 BMG Rifle vs. Death Star Pumpkin
Warning: These demonstrations were carried out on closed ranges by experienced professionals certified to use explosives. Possession of C4 and Det Cord may be a violation of various Federal, State, and local laws. Detonating cord and C4 are classified as high explosives and are regulated by the BATFE. Don’t even think about trying to repeat these stunts on your own.
Along with these popular cartridge types, DJ’s Brass can hydro-form 6 PPC, 30 PPC, 6 BRA, 30 BR, .260 AI, .284 Shehane and other wildcats.
Do you shoot a popular wildcat (such as the 6 BRA), but hate the hassle of fire-forming all your own cartridge brass? That takes time, costs money (in bullets and powder), and consumes precious barrel life. Well there IS a better solution — you can have your new brass hydro-formed to your exact specifications for a reasonable cost.
DJ’s Brass Service now offers custom case hydro-forming to your exact specs. Darrell Jones offers this service for a variety of popular cartridges: 6 PPC, 30 PPC, 30 BR, 6 BRA (BR Ackley), 6mm Grinch, 6 BRDX, 6 BRX, .260 Ackley, .284 Shehane and of course the very popular 6mm Dasher. After hydro-forming your brass, Darrell can also neck-up or neck-down the cases to meet your needs. For example, if you shoot a 22 Dasher, Darrell can hydro-form the cases to a 6 Dasher and then neck them down to .22 caliber. He can also turn the necks to your specs (for an additional charge).
Darrell is a hydro-forming wizard who has perfected the process over the last couple of years. He has learned a few special techniques along the way to ensure uniform case-forming.
Without revealing any trade secrets, we can say the Darrell has very special dies and Darrell doesn’t use a mallet or hammer — he has a system that is much more consistent. Darrell tells us: “Many of my customers take this brass and load it ‘as is’ and go straight to a match and shoot some very nice groups.”
Hydro-forming by Darrell costs $0.60 (sixty cents) per case with a minimum order of $60. Neck-turning is an additional $0.50 (fifty cents) per case plus actual return shipping. The turnaround is usually less than five days.
With Darrell’s hydro-forming service you don’t have to buy any special dies or other equipment. Darrell says: “Simply send me the brass you need or have it dropped-shipped to me along with a fired case that has not been sized. If you need formed brass for a new build (gun not yet fired), let me know and I will size the brass to fit within .001 of a PT&G GO gauge.”
For more information, visit DJsBrass.com, or call Darrell at (205) 461-4680. IMPORTANT: Contact Darrell for shipping instructions BEFORE sending brass for processing. In a hurry, don’t have time? Just call Darrell and he’ll make something work for you.
Hydro-Forming Customer Reports
Here are testimonials from recent customers.
“Recently had Darrell Jones of DJ’s Brass Service hydro-form 6 BRX brass for me. The turn around time was very fast and the brass was to the exact specification I ask for. I actually shot the hydro-formed brass in a match [without further fire-forming]. It shot a 3.597″ — pretty amazing. Let DJ do the work for you!” — Mike Wilson (3 Time IBS Record Holder; 2013 and 2014 1000-yard IBS Shooter of the Year.)
“Darrell Jones of DJ’s Brass Service went far beyond the call of duty, to assist me in preparation to shoot for my first time in an IBS match. I have had an interest in 1000-yard competition for many years and finally got the opportunity to try it. After researching the winning competitors, rifles, and rounds I ordered a Panda action with Krieger barrel in 6mm Dasher from Kelby’s. It was one week before the match and I had a rifle and no rounds. I contacted Darrell to hydraulically form 6mm dasher from Lapua 6mm BR brass. He formed the brass and had it in the mail the next day[.] Since I have only reloaded for hunting or magazine fed rifles I was not familiar with proper seating to allow land engagement of the bullets for 1000-yard accuracy. Darrell took the time to advised me every step of the way to allow me to shoot a 3.158″ (5) shot group to win my first round of my first competitive match ever.” — Mike Youngblood
Tomorrow is October 31st, Halloween (originally called “All Hallows’ Evening”). That means kids in costumes will be ringing doorbells as soon as it gets dark. No doubt some of you proscrastinators will wait ’til the last minute to set out your Halloween decorations and Jack-O-Lanterns. Don’t worry, in the video below, our friend, 3-Gun ace Taran Butler, shows how to carve a pumpkin in just about 5.5 seconds, give or take a tenth. Taran performed this feat of speed-carving with his trusty Infinity handgun, chambered in 9mm Major.
What Are the Origins of Halloween?
Halloween or Hallowe’en (a contraction of “All Hallows’ Evening”), also known as All Hallows’ Eve, is a yearly celebration observed on October 31, the eve of the Western Christian feast of All Hallows (or All Saints). According to many scholars, it was originally influenced by western European harvest festivals and festivals of the dead with possible pagan roots, particularly the Celtic Samhain. Others maintain that it originated independently of Samhain and has Christian roots.
“The blue plastic barrels that we have to shoot through are the idea of the local police — to ensure that we keep our rifles pointing at the targets!” — David Sharp
Here’s a great story from the other side of the pond — the United Kingdom. Shooting a .308 Win factory Savage rifle, a novice benchrest shooter set two new 1000-Yard UK Factory Sporter Class records with a group barely over three inches plus a 6.756″ four-group Aggregate. The Savage had been upgraded with an inexpensive aftermarket stock and Timney trigger, but was otherwise “as manufactured” — with factory barrel.
At Ingleston, competitors shoot for group size only — so there are no scoring-rings on the targets.
On October 14, 2018 David Sharp had a memorable performance at the Ingleston Range in Scotland. David Agg’d 6.756 inches for all four 5-shot groups, a new UK 1000-Yard record for the Factory Sporter Class. His smallest group measured 3.090 inches, which is also a new UK Factory Sporter record. Great Shooting David — congrats!
Sharp Sets Two New UK Factory Sporter Class 1000-Yard Records
Report by Vince Bottomley
In the UK, long-range benchrest is far more popular than short-range. The UKBRA (United Kingdom Benchrest Association) holds shoots at three venues: Diggle (100, 600 & 1000 yards), Bisley (100 yards only) and Ingleston in Dumfries, Scotland (1000 yards).
The Scottish venue is the UK’s latest 1000-yard facility. It was established just three years ago yet it is already holding well-attended monthly shoots. It is operated by the Galloway Small Arms Club and, as you may imagine, it is situated in the beautiful wild Scottish countryside.
The UKBRA operates under IBS/NBRSA rules for the Light and Heavy Gun Classes but, many of the Scottish members are also deer stalkers and came to the benches with their hunting rifles, so we also run a Factory Sporter Class. Factory Sporter rifles must be the original manufacturer’s barreled-action but a more benchrest-compatible stock may be used or ‘bag-rider’ attachments may be fitted to the butt and fore-end. The barreled-action must however be totally as it left the factory — no re-chambering or throating, though the crown may be re-cut. To discourage potentially dangerous trigger modifications, an after-market trigger may be fitted.
The Factory Sporter Class is very popular and Savage rifles, chambered for the 6mmBR, 6.5-284, and .308 Win are the favored factory-classers. These have produced some remarkable performances over the years, often out-performing custom rifles!
David Sharp is a True Sharp-Shooter
David Sharp is a relatively new benchrest shooter, though he has decades of firearms experience. David started his shooting days wild-fowling and rough shooting with a shotgun over 50 years ago. After retiring, he moved to Dumfriesshire and began shooting again — clay pigeon, wildfowling on the Solway, driven pheasant and deer stalking. As a stalker, David keeps his eye in by shooting targets on a local range using his .308 Mannlicher.
Eventually, the pains of old age began taking their toll and stomping up hills was becoming more difficult. Fortunately, David heard about the Ingleston 1000-yard range and joined the Galloway Small Arms Club in 2016. As a complete novice to benchrest shooting, David relied on the guidance and advice from his fellow Club members and eventually purchased a Savage Model 12 F-TR rifle in .308 Winchester to compete in the Factory Class.
Here’s the view looking downrange. What a beautiful place to shoot…
.308 Win Factory Savage with Choate Stock and Vortex Scope
David’s rifle has some upgrades, as permitted for Factory Sporter Class. The Savage trigger was replaced with a Timney. The Savage F-TR stock was replaced with a Choate Varmint stock fitted with a Sinclair front bag-rider. The Choate’s butt was home-modified to better ride the Edgewood bag. The rifle is fitted with a Vortex Golden Eagle 15-60 scope mounted on a 20 MOA Ken Farrell rail via Vortex rings. Dave shoots off a SEB Mini front rest. As the Mini is lighter to lug around than the SEB NEO (and less expensive), the Mini is becoming popular with UK shooters.
David reports: “My rounds are nothing special — I’m using Sierra 2155 155 grain bullets over Vihtavuori N140 powder and CCI 200 primers. I use Lapua brass (large primer) full-length sized in a Redding S bushing die to give 0.002″ neck-tension.”
Although the Ingleston Range is a beautiful place to shoot, as you can imagine conditions can vary dramatically and it is not known for mild days! However, at 9:00 am on the day of David’s record shoot, it was clear and quite still with the flags barely lifting. The temperature was already 15 deg C (59 deg F). What more could any benchrest shooter ask for?
In the photo of David above, you can just see the four 1000-yard targets in the extreme top right of the picture — up near the tree-line. Note, at Ingleston, competitors shoot for group size only. Hence there are no scoring-rings on the target. However, Vince Bottomley says score shooting may begin at some UK ranges: “This year we have purchased a set of electronic targets. The IBS target face can be inputted so we will now start to shoot for score as scores are registered instantly. Previously, it just took too long to score the targets as well as measure the groups.”
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. CDNN — Winchester XPR Rifle $289.99 after $75 Rebate
We like the Winchester XPR as an affordable, entry-level hunting rifle. The three-lug bolt has a short throw, the mags seat easily and the rifle balances well. CDNN is offering the XPR for just $364.99. That’s a great price, but it gets even better. Winchester is offering a $75.00 factory rebate, lowering your net cost to just $289.99. This CDNN deal is available now for four popular chamberings: .243 Win, .308 Win, .270 Win, and .30-06 SPR. Winchester’s $75 Factory Rebate applies to any new Winchester XPR or Model 70 rifle purchased from August 1 through October 31, 2018. For more info, visit Winchester’s Trophy Season Rebate Page.
FREE SCOPE! To sweeten the deal even more, right now CDNN is offering a FREE Weaver 3-9x40mm scope with each XPR rifle sold — check it out!
2. Midsouth — RCBS ChargeMaster Lite, $199.99
Tired of weighing your charges one by one to get the accuracy you’re looking for? Midsouth has the RCBS ChargeMaster Lite electronic scale/dispenser on sale for only $199.99. This is a great chance to pick up one of the best off-the-shelf powder scale/dispensers for an excellent price. You can pay up to $260.00 elsewhere. Supplies are limited so now’s the time to buy if you’ve had the ChargeMaster Lite on your shopping list.
3. Grizzly.com — Bald Eagle Rests $165.00 – $199.95
Bald Eagle (by Grizzly) offers one of the best value-priced front rests on the market. We’ve seen F-Class shooters win matches with the Bald Eagle Slingshot Windage Rest, which costs less than a fifth of a premium co-axial rest. For a new shooter, this is a very cost-effective solution. One Forum member purchased this Bald Eagle BE1006 rest for his grandson, deciding it was the best rest under $300.00. Both rests shown offer a cable (with large knob) for easy windage adjustment. The Slingshot model, in cast iron or aluminum, has an elongated front leg for added stability. This also brings the Windage knob within easy reach. The aluminum version (BE1005) is considerably lighter and $35 cheaper, so it may be preferred by rimfire and varmint shooters. Note: Front sandbag sold separately.
4. Al’s — Vortex Razor HD 20-60x85mm Spotting Scope, $854.99
Here’s a great deal on a high-quality spotting scope from a top optics maker. AL’s Sporting Goods has last year’s model Vortex Razor 20-60x85mm spotter for only $949.99, including eyepiece. But it gets better — use Code ALS10 for another 10% off, bringing the final price down to $854.99. This is a very good spotter for the money and as Vortex will tell you, “buy a Razor now and we’ll always replace it with a Razor in the future”.
5. Cabela’s — Garmin GPSMAP 64S $199.00 on Sale
Cabela’s has slashed its price on the popular Garmin GPSMAP 64S unit, on sale for $199.99. This is an excellent hand-held GPS for hunters and hikers, with long battery life, good reception, and a fairly large screen. This unit features a High-Sensitivity GPS, Glonass Receiver, and Barometric Altimeter (important for your ballistics). The Garmin GPSMAP 64S is also available at Amazon.com for $220.90 with free shipping.
6. Creedmoor Sports — Wilson Trimmer Kit, $159.95
Here’s a slick set-up for precision case trimming. Creedmoor’s complete L.E. Wilson stainless trimmer kit features micrometer-adjustable length stop (.001″ increments), improved deluxe SS handle, and a special Creedmoor platform. The platform/mounting board can store 9 different case holders and comes with a polymer tapping block for knocking cases out of the holder. The platform also has four rubber feet. This system is also power-adaptable. The L.E. Wilson Trimmer Platform Kit is marked down to $159.95 this week. We favor this kind of system for trimming match cases.
7. Stocky’s — LR Stocks with Aluminum Bedding Block, $179.99
Here’s a good deal on a versatile Stocky’s Long Range Stock with aluminum V-block bedding system. For just $179.99, order this for Rem/Rem Clone long actions or short actions, with either narrow or wide (varmint/tactical) barrel channel. This would be a good choice for a varmint rifle. This is also offered with handsome hydrographic or web-pattern baked-on textured finishes for $199.99.
8. Palmetto State Armory — 500 Rds CCI .22 LR, $16.99
Here is a crazy-good deal. Get 500 rounds of CCI 40gr .22 LR rimfire ammo for just $16.99. That works out to just 3.4 cents per round. But act soon. This deal on CCI Blazer rimfire ammo expires Monday October 29, 2018 at 11:59 pm EST. If you buy five or more 500-count boxes (that’s at least 2500 rounds), you can also get free shipping.
This nicely designed Jialitte Scope Bubble Level is fully CNC-machined to close tolerances for a good fit. It features a 30mm milled inside diameter, plus an inner insert ring so it will also fit 1″-diameter main tubes — that dual-diameter versatility is a nice feature. We also like the way the unit is nicely radiused, and has a low profile in the middle. User reviews have been very positive. You could easily pay $35.00 or more for a 30mm scope level. Purchasers have praised this product — almost all verified buyers have rated this five stars.
RCBS and Vortex selections by Forum member F-Class John.
Pick your passion — High Power, F-Class, Silhouette, Smallbore, Air Rifle, Pistol, Black Powder. The NRA runs National Championships for all these disciplines and more. Attending a National Championship event is a big commitment, but it’s worth it. You can meet new friends, test your mettle against the nation’s best, and record memories that can last a lifetime.
Mark your calendars boys and girls — here is the NRA’s initial 2019 National Match schedule. This includes the National High Power Championship, National Pistol Championship, Smallbore Championship, World Shooting Championship (WSC) and other major national events. For most events, you can click the link to access an official NRA championship page for that discipline. NOTE: Some dates/venues have not yet been finalized. To get more information, visit compete.nra.org or send email to: comphelp@nrahq.org.
NRA National Championships and National Matches in 2019
For those who prefer to neck-size their brass (rather than full-length-size), the LEE Collet Die is a popular, inexpensive option. It works by having collet tangs or “fingers” press the neck against a central mandrel. The benefit is that you get a very straight neck, which is sized consistently from top to bottom. Canadian shooter Jerry Teo explains: “LEE Collet Dies produce sized cases with very low runout (measured runout is under .001″ using a Sinclair concentricity gauge). You also don’t get the build-up of brass at the base of the neck, as can happen with bushing neck dies. The neck-shoulder junction stays nice and crisp.”
TIP ONE — Adjusting Tension
LEE Collet dies don’t have a specific mechanical adjustment for neck tension. But you CAN easily modify the die to provide more or less tension. If you want to adjust the neck tension using a Lee Collet die, you can simply chuck the mandrel in a drill and reduce the diameter with some sand-paper (to increase neck tension) or you can order a mandrel the next caliber larger and turn it to whatever diameter you want (the larger the mandrel diameter, the less the neck tension). You can also order custom mandrels from Lee sized to any diameter you want.
Regarding neck tension, Boyd Allen makes an important point: “The only way to properly get more neck tension with collet dies is to either reduce the diameter of the mandrel, or order a smaller-diameter mandrel from Lee. I remind folks that adjusting the die position to have more toggle at the top of the ram stroke (not the factory recommended method), or leaning on the press handle with more force than recommended will NOT increase neck tension.”
Lee also offers Custom Collet Dies, made from two fired cases. Lee offers custom standard collet dies for $70.00 (plus S/H) and custom large collet dies for $160.00 (plus S/H). CLICK HERE to ORDER.
TIP TWO — Polish and Tune for Easy Case Removal
Some users have complained that their Collet Dies grab the case-neck too firmly, making the case hard to remove. There are solutions to this problem. First inspect the collet fingers and smooth the inner surface up a bit with polishing compound or an extra-fine sanding pad. Second, you can open up the fingers a little bit. LEE recommends that if your Collet Die is sticking, take a steel punch and tap the fingers apart a little bit so that the natural “unloaded” position is wider. Lastly, you should lightly lubricate the outside of the collet fingers (see arrows) before you re-assemble the die. This will ensure they slide smoothly. Also, to prevent the collet fingers from closing too tight, never load up the die with your press without putting a case in place first. Without a case neck between the collet fingers and the mandrel, the collet can clamp itself too tight as you raise the ram.
TIP THREE — Always Have a Case Inside When Operating Collet Die
Our friend Boyd Allen tells us that you need to follow directions and NEVER operate the die without a case inside. Boyd explains: “This is because doing so will spring the quadrents of the collet inward so that they interfere with the insertion of a case, and the user will have to figure out how to undo the damage if the die is to operate properly. This advice would not be needed if everyone read the instructions before using the die…. but many times, they don’t. Another thing that I tell new users is to take the die apart so that they will have a better chance of understanding how it works.”
TIP FOUR — Size Twice and Spin Your Case 1/8th Turn
After reaching fully “down” on your press handle, withdraw the case about an inch and manually rotate it about 1/8th (NOT 1/4 or 1/2) turn while still in the shell-holder, then size again. This will place the die’s collet petals on the four “high spots” of the case neck and will result in a rounder, more evenly-sized neck with slightly more bullet tension. This takes only about one second more per case and is well worth the slight extra effort. (We thank reader Stonecreek for this smart tip).
Here’s a good video that explains how to use a Lee Collet Die to Neck-Size .243 Win brass:
• Front Bag Tension — Vertical can happen if the front sand bag grips the fore-arm too tightly. If…the fore-arm feels like it is stuck in the bag, then the front bag’s grip is too tight. Your rifle should move in evenly and smoothly in the sand bags, not jerk or chatter when you pull the gun back by hand.
Tips for Priming with Progressive Presses
Darrell is a hydro-forming wizard who has perfected the process over the last couple of years. He has learned a few special techniques along the way to ensure uniform case-forming.
Tomorrow is October 31st, Halloween (originally called “All Hallows’ Evening”). That means kids in costumes will be ringing doorbells as soon as it gets dark. No doubt some of you proscrastinators will wait ’til the last minute to set out your Halloween decorations and Jack-O-Lanterns. Don’t worry, in the video below, our friend, 3-Gun ace 
TIP ONE — Adjusting Tension
TIP TWO — Polish and Tune for Easy Case Removal
