What do you get when you cut a 6.5 Creedmoor-chambered barrel down to just over 16 inches? A lot more velocity than you might think. Our friends at Rifleshooter.com recently did a barrel cut-down test with 6.5 Creedmoor test rifle, shortening the barrel from 27 to 16.1 inches in one-inch increments. Surprisingly, with a 142gr Sierra MK, the total velocity loss (as measured with a Magnetospeed) was just 158 FPS, an average of 14.4 FPS per inch of barrel length. With the lighter 120gr A-Max bullet, the total velocity loss was 233 FPS, or 21.8 FPS average loss per inch of barrel.
Test Procedure
Five (5) rounds of each type of cartridge were fired at each barrel length and the velocity data was recorded with a MagnetoSpeed V3 barrel-mounted chronograph. The rifle was then cleared and the barrel was cut back one inch at a time from 27″ to just over 16″. NOTE: During this winter test, the air temperature was a very chilly 23° F. One would expect higher velocities across the board had the outside temperature been higher.
The photo below shows how the barrel was cut down, inch-by-inch, using a rotary saw. The barrel was pre-scored at inch intervals. As the main purpose of the test was to measure velocity (not accuracy) the testers did not attempt to create perfect crowns.
6.5 Creedmoor vs. Other Mid-Sized 6.5mm Cartridges
The 6.5 Creedmoor is a very popular cartridge with the tactical and PRS crowd. This mid-size cartridge offers good ballistics, with less recoil than a .308 Winchester. There’s an excellent selection of 6.5mm bullets, and many powder choices for this cartridge. When compared to the very accurate 6.5×47 Lapua cartridge, the 6.5 Creedmoor offers similar performance with less expensive brass. For a tactical shooter who must sometimes leave brass on the ground, brass cost is a factor to consider. Here’s a selection of various 6.5 mm mid-sized cartridges. Left to right are: 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor with 120gr A-Max, 6.5 Creedmoor with 142gr Sierra MK, and .260 Remington.
When asked to compare the 6.5 Creedmoor to the 6.5×47 Lapua, Rifleshooter.com’s editor stated: “If you don’t hand load, or are new to precision rifle shooting, get a 6.5 Creedmoor. If you shoot a lot, reload, have more disposable income, and like more esoteric cartridges, get a 6.5×47 Lapua. I am a big fan of the 6.5×47 Lapua. In my personal experience, the 6.5×47 Lapua seems to be slightly more accurate than the 6.5 Creedmoor. I attribute this to the quality of Lapua brass.”
Our friend Kirsten Joy Weiss has just released a useful video that shows how to refine your trigger control for better accuracy. In this video, Kirsten talks about the actual placement of a shooter’s index finger on the trigger. It is important to have the finger positioned optimally. Otherwise you can pull the shot slightly left or slightly right.
Kirsten tells us: “Finger placement on the trigger might not seem like a big deal, but it actually is. The reason for this is because, depending on where your index finger is placed on the trigger, [this] translates to different muscle interactions with the gun.” Watch this video to see Kirsten demonstrate proper finger placement (and explain problems caused by improper finger positioning).
Here Kirsten Illustrates how the index finger should be aligned along the face of the trigger shoe.
When you pull the trigger, you only want to engage the last section of your finger, in order to avoid unwanted muscle engagement and to achieve a smooth shot.
Remember there is a “sweet spot” between the crease (first joint) and the tip of the finger. If you position the trigger in that “sweet spot”, you should see an increase in your accuracy. Don’t make the mistake of putting the trigger in the crease of your finger, as shown below.
Effects of Incorrect Finger Placements
You want to place the trigger shoe between the end of your finger and the first joint. If you place the trigger on the very tip of you finger you’ll tend to push the rear of the rifle to the left when engaging the trigger, causing shots to go right (for a right-handed shooter). On the other hand, if you put the trigger in the crease (first joint), you’ll tend to bring the rear of the rifle to the right, causing shots to fall left. This is illustrated below for a right-handed shooter.
At the request of many Forum members, we’re reprising this archived video from past IBS 600-yard Shooter of the Year Samuel Hall. Without a doubt, Sam is one of the best mid-range benchrest shooters in the nation. While the video quality is rough (to say the least), Sam’s offers plenty of tips you can “take to the bank”. Even if you don’t shoot competitively, the techniques described here can improve your accuracy when shooting from a bench.
2008 IBS 600-yard National Champion Samuel Hall has prepared a 9-minute VIDEO showing his techniques for shooting from the bench. Sam covers a number of topics including bag set-up, body position, bolt manipulation, and loading skills. He also explains the importance of having a relaxed, comfortable posture and keeping your head in the same position shot to shot.
If you’re serious about accurate benchrest shooting, at ANY distance, you should watch this video. Sam’s tips can really help you. We guarantee it. While the video itself is grainy and wind noise affects the audio, you can still glean many great points from the video. From minute 8:00 on Sam shoots a 5-shot string on camera with his BAT-actioned, Leonard-stocked 6BR. Though he was fighting 20-mph winds Sam achieves a half-inch group at 200 yards. Quarter-MOA in such conditions is good shooting.
The NRA Blog has produced an interesting graphic guide to firearms function. This “How Guns Work” infographic shows the basics of bolt-action rifle operation and how a centerfire cartridge propels a bullet through a barrel during the “firing sequence”. There’s some good artistry here, with cutaway drawings letting you look inside an action and cartridge.
Enjoy this technical graphic. The NRA Blog says: “In celebration of cartridges big and small, we partnered with OutdoorHub to bring you a detailed look into how guns work. While the infographic will be most instructive to newcomers, we think avid shooters will find it interesting, too.”
Someone is going to snag a heck of a deal. As part of its End of Year Clearance Sale, Midsouth Shooters Supply is offering bulk quantities of quality Norma brass at a huge discount. Right now you can get 2000 pieces of Norma 6mm PPC or 6mmBR brass for just $798.26. You can also get twenty-five .22 PPC cases for just $11.06. There are similar discounts on other products at Midsouth, but we just had to bring this to our readers’ attention. That’s enough brass to last a lifetime. If you are thinking of building a PPC-based or BR-based varmint rifle, such as a 22BR, 2000 cases will see you through a week-long varmint safari. This brass would also make a great item for a youth program.
The Norma brass is outstanding — certainly capable of winning matches. It may not be quite as hard as Lapua brass, but it is nonetheless very high quality stuff. NOTE: This is the last day of Midsouth’s E.0.Y.C. sale, so don’t dawdle. You snooze you loose. You could pick up one of these 2000-count cartons and sell off some to your shooting buddies.
OK, you guys can now officially stop complaining about the price of rimfire ammunition. Right now Cabelas.com is offering “Holiday Packs” of 40gr CCI standard velocity LRN ammo. Price is $3.99 for 50 rounds, with no limits (until inventory is sold). If you need good, reliable plinking ammo… place your order soon. Here’s a review from a recent purchaser: “Good Deal! I ordered 40 boxes and got them all. I have already used a box and they work great! I may need to order more before they are all gone! Would you recommend this product to a friend? Yes.”
NOTE to California-based readers — you may want to stock up on affordable .22 LR ammo before the ammo-buyer licensing requirements take effect on 1/1/2018. New laws will prohibit all mail-order ammo sales for California residents.
Terms of Sale: Online Only, Do Not Call, one coupon per order.
Item number#: IK-219647; SKU#: 931GFT ($4.99); Sale Price $3.99 per 50-round box.
Here is the original Sierra manufacturing facility in Whittier, CA.
Sierra Bullets — How It Got Started
Report Based on Story by Carroll Pilant, Sierra Bullets Media Relations Manager
What became Sierra Bullets started in the late 1940s in a Quonset hut in California. In 1947, three aircraft machinists, Frank Snow, Jim Spivey, and Loren Harbor, rented machine space to produce rivets for the aircraft industry along with fishing rod guides and rifle front sight ramps. In the post-WWII years, sport shooting was becoming hugely popular, but quality ammunition was in short supply. For shooting enthusiasts, reloading was the solution to the ammo supply shortage. Snow, Spivey, and Harbor recognized this, creating Sierra Bullets to help fill the void. Before long, they were selling a 53-grain match bullet to the Hollywood Gun Shop. These bullets are still in production today as the Sierra #1400 53-grain MatchKing.
A few years later, an accomplished competitive shooter named Martin Hull joined Sierra. Hull helped develop new bullet types and served as manager of Sierra’s ballistics laboratory for nearly 20 years. With Hull’s help, Sierra’s output grew rapidly. The California company outgrew several locations before it moved to a large facility in Santa Fe Springs, CA, in 1963.
New Owners and New President in the Late Sixties
In 1968, the Leisure Group bought Sierra Bullets. Other Leisure Group companies included Lyman Reloading, High Standard Manufacturing Company, Yard Man, Thompson Sprinkler Systems, Flexible Flyer Sleds, and Dodge Trophies (Which made the Oscar and Rose Bowl Game trophies).
Soon after purchasing Sierra, the Leisure Group hired Robert Hayden as President and General Manager. Hayden was a mechanical engineer who had worked for Remington Arms. Hayden remained the president of Sierra for 42 years, retiring in 2012 when Pat Daly became president.
Sierra Moves to Missouri
In 1990, Sierra relocated to Sedalia, Missouri, where the company remains today. Sierra Bullets now employs over 100 people including five full-time ballistic technicians who answer daily reloading and firearms questions by both phone and e-mail.
The Making of MatchKings — How Sierra Produces SMKs
All Sierra bullets begin life as a strip of gilding metal, an alloy consisting of 95% copper and 5% zinc. To meet Sierra’s strict quality requirements, the gilding metal requires three times more dimensional and quality control standards than is considered standard in the copper manufacturing industry.
A blanking press stamps out a uniform disc and forms the cup that will be drawn into the MatchKing jacket. The cup is then polished and sent to a draw press to be drawn into a jacket that is longer than needed for the future MatchKing, thus allowing for the trim process. Press operators constantly check concentricity to make sure we have only quality jackets. The jackets then go to a trimmer where they are visually inspected again.
After being polished a second time, the jacket travels to the bullet press. In the meantime, 80-pound lead billets are being extruded into lead wire for the cores where great care is taken so that the core wire is not stretched. The core wire is lightly oiled before continuing to the bullet press to be swaged.
The lead core wire and trimmed jacket meet at the bullet press where the first stage forms a boattail on the jacket. The lead core is then formed on top of the bullet press and fed down into the jacket. In one stroke of the press, the MatchKing is formed.
Quality control technicians pull samples from each lot of MatchKings to make sure they meet Sierra’s stringent standards. Samples are then sent to Sierra’s 300-meter underground test range (shown below) to be shot for accuracy on mechanical mounts referred to as “unrestricted return to battery rests” that Sierra designed and built in-house.
After inspection, the bullets are placed in the familiar green box along with reloading labels. They are then shrink-wrapped and shipped all over the world.
A 7mm Snake for Santiago
Our friend Dennis Santiago has a reptilian rig in his arsenal. It’s actually an Eliseo R1 single-shot tubegun chambered in .284 Winchester. The eye-catching aspect of Santiago’s .284 bolt-gun is the snakeskin dip job on the exterior. This really creates a distinctive look. Dennis tells us: “It was Gary Eliseo’s idea to try a water-transfer printing finish for this rifle. There are many patterns to choose from — this is the WTP-260 Snakeskin Illusion-Fall Copper from WaterTransferPrinting.com. For a single shot LR gun, I figured something on the bright side would be interesting and pick up less heat from the sun in the summer.”
Dennis will use his new rifle in prone matches, where a single shot works fine. He says: “Underneath the hood, it’s a Rem 700 Long Action, chambered in .284 Win. Yes it’s a single shot! I don’t need anything else for a prone gun. Nothing to get in the way of building the perfect position.”
Dennis says: “Length of pull, offset and cast initially set the same as my similar RTS .308. My gun, my body dimensions.”
A FFP 6-24x50mm Sightron Rides on Top
The optic is a Sightron 6-24x50mm, FFP MOA-2. Dennis reports: “I looked at many scopes (within my determined price range), and this is the one that had the best combination of features for for this gun’s particular application. The sight line sits about 3 inches above bore line on these guns. It’s been leveled, bore-sighted and pre-dialed for a 200-yard estimated zero for the ammo I plan to use. Those are Gen II A.R.M.S. rings. Super easy to tailor to different rail widths. Same rock-steady steel performance.”
Images courtesy of Bernard Martinage and AmVIEWnition
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Midsouth — End of Year Clearance with 42% to 77% Off
Now through 12/31/2016, Midsouth Shooters Supply is running its incredible End of Year Clearance (E.O.Y.C.) Sale. Prices are lowered each day as we approach the end of 2016. Eventually prices will be 77% off. The deals get better with time…but if you wait too long, someone else may grab the item(s) you want. We suggest you check back daily.
NORMA BRASS on SALE: As part of Midsouth’s E.O.Y.C., Norma match brass is on sale. For example, right now .22 PPC, 6mm PPC, and 6mmBR Norma brass are 35% off. This is excellent brass — maybe not quite as hard as Lapua, but still very, very good. You can get the 6BR brass today for just $57.38 per hundred — that’s a huge savings compared to new Lapua 6mmBR brass.
2. CDNN Sports — Ruger .308 Win American, $299.99
If you want a simple, reliable, and very affordable deer rifle, look no further. Right now the Ruger American in .308 Win is on sale for just $299.99. This rifle features a crisp trigger, short-lift 3-lug bolt, and smooth-feeding flush-fit rotary magazine. An integral bedding block system positively locates the receiver and free-floats the 22″, 1:10″-twist barrel. The polymer stock has a matte camo finish and soft rubber recoil pad. For a basic, work-horse hunting rifle it’s hard to beat this 6.1-lb Ruger for $299.99.
3. Natchez — Special 5 Reloading Press Kit, $199.99
Looking for a great holiday gift for a family member getting started in metallic cartridge reloading? This RCBS Kit has everything a new reloader needs: single-stage press, powder measure, scale, powder trickler, priming tool, cartridge tray, “rocket” chamfer tool, case lube and more. This is an excellent entry-level reloading kit, on sale for just $199.99 at Natchez Shooters Supplies. We like the relatively compact Special 5 press for most reloading duties. Eventually you may want to add an additional, large heavy press, but this will get the job done. For the combined package, with all the tools one needs to hand-load quality ammo — this is a stunningly good deal at $199.99.
4. Cabela’s — Vortex Crossfire II 1-4x24mm scope, $99.99
New NRA/CMP Service Rifle rules allow the use of optics up to 4.5X magnification. You don’t need a big budget to equip your AR Service Rifle with a suitable scope. This week, Cabelas is offering the Vortex Crossfire II 1-4x24mm scope for just $99.99. That’s a true bargain. This scope can also work for a bolt-action hunting rifle, providing fast acquisition and a wide field of view. Along with this low price you can get $5 Flat Shipping with Code 2016FLAT (this applies to all orders over $99.00).
5. Stocky’s Stocks — Composite Stock with Bedding Block, $179.99
Here’s a killer deal on a versatile Stocky’s Long Range Stock with aluminum V-block bedding system. For just $179.99, order this for Rem/Rem Clone long actions or short actions, with either narrow or wide (varmint/tactical) barrel channel. This would be a good choice for a varmint rifle. This is also offered with a matte black, tan, or olive baked-on textured finish for $199.99.
6. Amazon — Motorola Walkie Talkies, $46.99 per Pair
Walkie-Talkies are “must-have” items for long-range shooting. The 22-CH Motorola MH230R Two-Way Radio is Amazon’s #1 Best Seller in FRS/GMRS Handheld Radios. This under-$50.00 set offers 22 channels with a claimed range up to 23 miles (We’ve used them and they worked at 3 miles line of sight). The kit includes: 2 radios, 2 belt clips, 1 dual drop-in charger, 1 charging adapter, 2 NiMH rechargeable battery packs. Run-time is about 10 hours — plenty for a full day of shooting. There is also a newer version, the Motorola T260 for $58.99.
7. Amazon — Frankford Quick-N-EZ Case Tumbler, $34.99
Look no further for a great deal on a reliable tumbler. We’ve used this very same machine to tumble both pistol brass and rifle cases. We like the see-through, transparent top and the large capacity — this will hold up to 350 .223 Rem cases. With 1000+ customer reviews on Amazon.com, this Frankford Quick-N-Easy Case Tumbler has earned a 4.5-star rating. If you need a tumbler, you might want to order soon — this is the best price we’ve seen in a while.
Need quality .22 LR rimfire ammo at an affordable price? Consider Norma. Most folks think Norma only produces centerfire ammo and cartridge brass. As a result, people haven’t been looking for Norma rimfire ammo. Their loss is your gain. Accurate, reliable Norma .22 LR ammunition is in-stock right now at leading online vendors. This is good quality ammo, made in Europe. Bullets.com has Norma Tac-22 ammo in stock at $5.25 per 50-rd box (SKU: BL7819). In addition, Bullets.com offers Norma Match-22 ammunition at $7.50 per 50-rd box (SKU: BL11887).
We like reactive targets. It’s fun to “ring steel” and see a target move instantly when hit. For just twenty bucks (including shipping), it’s hard to go wrong with this 8″ AR500 Steel Gong. The 8″-diameter size is big enough for zeroing at 200 yards, yet offers a nice challenge at 500 yards and beyond. There is also a 6″-diameter model for $16.00.
Our friend, gunsmith/stockmaker Doan Trevor recently created a lovely, one-of-a-kind silhouette stock for an Anschutz rimfire action. Built as a true custom design, this stock combines ideal standing position ergonomics with light weight — the entire stock weighs a mere two pounds. This project really showcases Doan’s remarkable skills with wood. Read the full story about this project (with more photos) at DoanTrever.com.
Doan explains his design process: “A customer came to me wanting to know if I could build a silhouette stock that was 2 pounds or less. I used the Koa wood because it is a lower specific gravity than Walnut (which makes it lighter) and stronger. I was still able to use pillar bedding and keep the weight down. The fore end could be shortened to reduce the weight even more. Since the drops on a silhouette rifle are different than a prone rifle, I kept the pistol grip from the prone rifle which is comfortable and tried to come up with a higher cheek piece and more drop to the buttplate. All of this required lots of hand carving.”
A 7mm Snake for Santiago
