K&M Precision Shooting Products has two very handy products you may not know about yet. The first, a brilliantly simple device that lets you see your case necks as you expand them, can be used by anyone who necks-up brass (with a compatible expander die body). The second new product is a specialized “fat grip” holder that will make neck-turning easier for those of you out there who use K&M neck-turners.
K&M Expand Mandrel Window Riser
This is a simple threaded extension placed between your expander die body (K&M Expand Iron) and the top of your press. It carries the expander mandrel higher, above the press, and has a cut-out view port so you can see the mandrel as it passes through the neck. Smart, eh? This provides visual feedback during the process of expanding your brass. The patent-pending view riser costs $20.00. Will it expand necks faster, or reduce run-out? We doubt it, but we still would like to have one, if only to eyeball the mandrel to control the neck-entry rate more consistently from case to case.
Installation: Thread the Expand Mandrel Window Riser into the top of your loading press, then thread the K&M Expand-Iron (Expander Die Body) fully into the top of the window riser and adjust each so you can stroke out the press completely without driving the case mouth into the press adapter. This allows you to view the expanding operation which is typically blind under the press. The riser also eliminates the need for the stop screw in the expander mandrel. LINK: Expand Window Riser Instructions (PDF).
Ergo Holder for K&M Neck-Turning Tool
K&M’s rounded, oversized Ergo Holder lets you hold the K&M neck-turning body more securely (and with less hand cramping). Priced at $35.00, it is an expensive accessory, but we suspect many guys with K&M neck-turners will spring for an Ergo holder just because it gives you a more secure and comfortable grip on the small, square-edged K&M neck-turner.
Customer Feedback Inspired K&M’s Ergo Holder
The folks at K&M told us that their new Ergo Holder was produced in response to customer requests: “[Customers reported that] the neck turner can be hard to hold due to its compact size, especially in high-volume use. The Ergo Holder is machined from aluminum, providing a fatigue-proof grasp of the neck turner. Its mass works like a heat sink to help dissipate heat from the pilot during the turning process. The neck-turner body easily assembles into the Ergo Holder and is held in place with one set screw. The Ergo holder is also designed with the dial indicator in mind and actually makes its use more convenient”.
LINK: Ergo Holder Installation/Use Instructions (PDF).
Share the post "K&M Ported Expander Mandrel Riser and Neck-Turner Grip"
if you turn your case-necks, here’s a tool from 21st Century Shooting that can can save time, and help you produce better, more consistent turned necks. 21st Century’s Neck-Turning Lathe system, introduced last spring, may revolutionize the way reloaders turn their case necks. Watch the video and you’ll see why. If you’re never turned cases before, you may become a convert after seeing how quickly and easily the new 21st Century Neck-Turning Lathe does the job.
The mini-lathe has unique fittings on the left and right sides that allow both the case-holder and the neck-turning tool to float. As a result this tool maintains near-perfect concentricity during the cut. 21st Century’s John Perkins explains: “The floating design of the neck turner and the case driver allows the case mouth (bore) to run on the arbor absolutely concentric, therefore allowing O.D. to be turned concentric with I.D. The tailstock creates a horizontal inline support for the base of the case. This also allows the operator to keep both hands on the power screw driver or drill, making it very easy to control the feed rate and to produce a very fine, turned finish.” Having the system float at both ends was key, according to John: “By allowing both the turner and the case to float, everything self-aligns. This maintains concentricity and allows the unit to work with very low torque.”
Neck-Turning Lathe is Fast Yet Precise
Using power from a drill or electric screwdriver, this tool will turn necks fast — in a matter of a few seconds. And it produces beautiful, smooth necks that are extremely uniform. Tests show that the lathe, used with the 21st Century Neck-Turning Tool, will hold 0.0002 (two ten-thousandths) neck wall tolerances. And it will do that time after time.
Turn Necks in a Single Pass
Using traditional hand-methods, turning case necks can be time-consuming and fatiguing. Many folks will experience hand pain or cramping after just a dozen cases. Watch the video, you’ll see how fast and easy neck-turning can be with the new mini-lathe. You get an exceptionally good cut in seconds. Very importantly, with this system, you may be able to switch from a double-pass cut, to a single-pass cut. Yes, even if you’re making a deep cut, we think there is a good chance you can turn all your necks in a single pass. That can cut your labor time in half!
Why does the 21st Century Neck-Turning Tool cut so well? First, the Neck-Turning Tool employs ultra-sharp carbide cutters that are custom-ground to fit the shoulder angle of your cartridge. This allows you to make a perfect cut extending down the shoulder 1/32 of an inch. Second, the system aligns the case neck on the arbor (mandrel) so well, and the cutter is so sharp, that very little torque is required. This allows the cutting process to go very smoothly. The case-holder is also unique — it features a O-ring so it holds the case firmly in place without marring or bending the case head. The tailstock case-holder adjusts to accommodate cases from 17 Fireball to a .416 Rigby.
More Case Prep Tools for Lathe in Future
In the near future 21st Century will offer additional case prep attachments for the new mini-lathe. 21st Century plans to provide bullet-pointing system and other options. These will all work with the same lathe “chassis”, and will run with power. John states: “This is a modular system, all parts interchange. So if you have an existing 21st Century Shooting Neck Turning Tool or Bracket, everything will fit.”
The 21st Century Neck-Turning Lathe costs $245.00, complete with Neck-Turning Tool ($85.00 value) and one case-holder driver. The Neck-Turning Tool comes with a carbide cutter with user choice of shoulder angle (Arbors and Mandrels are sold separately). Perkins recommends using the Neck-Turning Lathe with power, but it will also work with an optional hand crank. NOTE: Currently the Neck-Turning Lathe works ONLY with the 21st Century Neck-Turner. It will not work with K&M, Sinclair, or Forster tools. But that’s not a real drawback because the 21st Century tool is certainly one of the best on the market today. You can purchase the Neck-Turning Lathe (complete with Neck-Turner and Case-Holder) through the 21st Century website, or call (260) 273-9909.
Disclosure: 21st Century Shooting advertises with AccurateShooter.com.
Share the post "Neck-Turning Lathe from 21st Century Shooting"
K&M Precision Shooting Products has two very handy products you may not know about yet. The first, a brilliantly simple device that lets you see your case necks as you expand them, can be used by anyone who necks-up brass (with a compatible expander die body). The second new product is a specialized “fat grip” holder that will make neck-turning easier for those of you out there who use K&M neck-turners.
K&M Expand Mandrel Window Riser
This is a simple threaded extension placed between your expander die body (K&M Expand Iron) and the top of your press. It carries the expander mandrel higher, above the press, and has a cut-out view port so you can see the mandrel as it passes through the neck. Smart, eh? This provides visual feedback during the process of expanding your brass. The patent-pending view riser costs $20.00. Will it expand necks faster, or reduce run-out? We doubt it, but we still would like to have one, if only to eyeball the mandrel to control the neck-entry rate more consistently from case to case.
Installation: Thread the Expand Mandrel Window Riser into the top of your loading press, then thread the K&M Expand-Iron (Expander Die Body) fully into the top of the window riser and adjust each so you can stroke out the press completely without driving the case mouth into the press adapter. This allows you to view the expanding operation which is typically blind under the press. The riser also eliminates the need for the stop screw in the expander mandrel. LINK: Expand Window Riser Instructions (PDF).
Ergo Holder for K&M Neck-Turning Tool
K&M’s rounded, oversized Ergo Holder lets you hold the K&M neck-turning body more securely (and with less hand cramping). Priced at $35.00, it is an expensive accessory, but we suspect many guys with K&M neck-turners will spring for an Ergo holder just because it gives you a more secure and comfortable grip on the small, square-edged K&M neck-turner.
Customer Feedback Inspired K&M’s Ergo Holder
The folks at K&M told us that their new Ergo Holder was produced in response to customer requests: “[Customers reported that] the neck turner can be hard to hold due to its compact size, especially in high-volume use. The Ergo Holder is machined from aluminum, providing a fatigue-proof grasp of the neck turner. Its mass works like a heat sink to help dissipate heat from the pilot during the turning process. The neck-turner body easily assembles into the Ergo Holder and is held in place with one set screw. The Ergo holder is also designed with the dial indicator in mind and actually makes its use more convenient”.
LINK: Ergo Holder Installation/Use Instructions (PDF).
Credit Forum Member EdLongRange for spotting these new K&M products.
Share the post "See-Through Expander Riser and Ergo Holder from K&M"
The PMA Neck Turning Tool, review by Danny Reever PMA Tool was founded by Matt Harris and Pat Reagin, two former employees of Fred Sinclair. They both worked their way through college working for and designing tools for Sinclair Int’l. They now have branched out on their own and are offering some unique tools for the reloader.
I, like many other shooters out there, would sooner take a beating than change the settings of my neck turner. Many shooters even go out and buy a separate neck turner for every caliber — just so they don’t have to adjust the settings. Most of you know what it’s like, you ruin half dozen cases (or more) getting your neck turner just right, and if you change it the chances of getting it back to where it was are practically nil. Let me be the first to tell you those days are over! Like many of you, I first saw the PMA Neck Turning Tool in an advertisement on this website’s home page. It’s hard to miss, blue anodized finish with the large PMA logo on the body.
PMA Tool Moves the Mandrel, Not the Cutter Tip From PMA’s website I learned that this turner does NOT use a coarse or fine drive screw to move the cutter towards or away from the mandrel. Nor does the PMA tool move the mandrel on an eccentric (another method of cutting depth control). The PMA tool does something very different. PMA’s Model A Neck Turning Tool simply adjusts by moving the mandrel toward or away from the stationary cutter with an 80 TPI drive screw with 60 indicating marks. Each mark moves the mandrel .0002″ (two ten-thousandths). I found, if you stop between the marks, .0001″ isn’t out of the question. It’s such a smart arrangement, I wondered “why didn’t anyone think of that before?”
Use PMA, 21st Century, or Sinclair Int’l Mandrels
My interest now piqued, I contacted Pat Reagin for one of the PMA tools. Pat suggested that I also use PMA’s stainless expander and turning mandrels since they have put a lot of effort to get them exactly right. I might mention that the 3/8 shank stainless or carbide mandrels from 21st Century or Sinclair Int’l will work also. PMA does have carbide turning mandrels in the works — a nice upgrade for those of you who turn lots of cases at one sitting. I personally didn’t encounter any unnecessary heat build-up with the stainless mandrels only turning 10-20 cases at a time. Considering that carbide mandrels run about $40.00 compared to $7.95 for stainless, it’s nice to save a couple of bucks when you can.
Cut-Depth Settings Can Be Dialed “Dead-On” (Even after Caliber Changes)
Upon receiving the PMA tool I immediately went to my reloading room to set it up for turning some culled .308 Lapua brass — to clean it up 75% for a no-turn chamber. I followed the directions included with the turner and it was a snap to set up. After turning a few of the .308s I made note of my setting and changed both mandrels to 6MM to turn some Lapua 6BR brass for my .269″-neck chamber. Again the change went smooth as silk and I was turning the 6BRs in no time for my preferred loaded neck diameter of .26730″. I then decided to take the leap of faith and change back to turning the .308s after making note of the 6BR setting. That worked, so I then again switched back again to the 6BR setting — again with success. I have gone back and forth (between calibers) numerous times in the last couple of weeks. Each time I easily returned to my caliber-specific settings and I did not ruin a single case in the process. Without sounding like I’m gushing here I must say this is the nicest neck turner that I have ever used. The adjustments are so easy and repeatable “Even a cave man can do it”!
If, like me, you absolutely hate setting up neck turners, for fear of losing your settings, you owe it to yourself to give the PMA Model A neck turner a try. I think you’ll be impressed. The PMA Neck Turning Tool costs $95.95, complete with one carbide cutter with your choice of 30° or 40° shoulder angle.
Disclosure: Danny Reever is a Forum Member. He received no “freebies” or compensation. PMA Tools advertises on AccurateShooter.com.
Share the post "Gear Review: PMA Neck Turning Tool"
The wizard tool designer who runs 21st Century Shooting has invented a clever yet inexpensive new bench accessory that makes it much easier to turn case-necks. 21st Century’s new Neck Turning Tool Swivel Bracket gives you a “third hand” when using the 21st Century Neck Turning Tool, simplifying the process of neck turning, particularly when using power.
CNC-machined from aluminum billet, 21st Century’s Swivel Bracket mounts right on your bench. You can either attach it semi-permanently with screws or simply clamp it in place. Adjust your neck-turning tool (red unit in photo), at any angle from 0-90°, for best viewing of the cutter operation. With your neck-turning tool attached to the bracket, you have easy access to the arbor adjustment screw, arbor screw clamp, and the bracket rotation clamp screw. Once you’ve adjusted the angle, and locked the neck turner in place with the supplied Allen wrench, you can concentrate on turning the case, either by hand, or with power assist. The neck-turning tool is held securely; however, rubber bushings on the bracket allow the neck-turning tool to “float” just enough to work properly when using power.
This new Neck Turning Tool Swivel Bracket is simple, but very effective. It really does help you turn necks with greater ease and a greater sense of security. Importantly, the bracket lessens hand fatigue. No more “cramped hand syndrome” from struggling to hold the neck-turner steady. We really like this little device, and it only costs $19.95. However, for the time being, the Swivel Bracket ONLY works with the 21st Century Neck Turning Tool — it does NOT work with a Hornady, K&M, Neilson, or Sinclair Neck Turning Tools. For more info, call 260-273-9909 or visit 21stCenturyShooting.com.
Share the post "New Neck-Turning Tool Holder from 21st Century Shooting"
Gear Review: 21st Century Neck Turner by Germán A. Salazar
A new neck-turning tool with easy adjustments, super-high quality of manufacturing and an ergonomic design sounds like a good thing to me. If you also like good tools and like to keep up with developments in the field, read on (most of the pictures can be enlarged by clicking on them).
I recently received the new Neck-Turning Tool made by John at 21st Century Shooting. I always enjoy seeing John’s work because he really has a good grasp on how a tool should be designed to work effectively and this tool certainly fits that mold. The basic requirements of a good neck turner are: (a) accurate adjustments, (b) good blade design, (c) ergonomic design and (d) a well thought-out system of ancillary items. Let’s look at each of those areas and give the tool a test drive.
Handy Cut-Depth Adjustment Dial
The 21st Century neck turner has a unique dial adjustment for the depth of the cut which makes small adjustments simple and fast. Each full number represents 0.001″ of cutter movement, and the fine lines in between let you zero in on the exact neck wall thickness that you need. The dial is simply turned in until the desired neck thickness is reached. If you go too far, it’s best to turn it out a full turn, then back in once again; this reduces the effect of any backlash that might exist in the threads. I found the dial easy to use and had no trouble getting to my usual thickness setting of 0.0125″.
Excellent Carbide Cutter Blade Design
At its core, a neck turner is a cutting tool and good blade design is what sets any good cutting tool apart from the competition. Here, John really shows his ability as a designer and manufacturer. The blade supplied on my tool is carbide and cuts brass effortlessly, however, that’s not the real point of interest. Many neck turners have blades with less than ideal nose radius and create a “threading” effect on the neck unless the tool is fed over the brass at a very slow rate. The 21st Century blade has a good radius at the transition to the shoulder angle which allows for a smooth cut with a reasonable feed rate.
The shoulder angle is another well thought-out feature as it is a very close match to the actual shoulder angle of the case. This allows you to bring the cutter a bit further into the shoulder without weakening it and definitely avoid the subsequent occurrence of the donut of thick brass at the base of the neck. (When ordering, 21st Century lets you specify one of four (4) different cutter shoulder angles to match your particular cartridge: 20°, 30°, 35°, and 40°.) The photo of the case in the cutter shows the cutter making solid contact with the shoulder after a substantial cut on the neck, yet the shoulder was really just lightly touched. I backed the cutter off a bit from this setting for the final adjustment. If you tend to use heavy bullets which extend below the base of the neck, this feature alone makes John’s tool worthwhile.
Turning necks is tedious, especially if you’re turning a large number of cases as High Power shooters generally do. Accordingly, a design that takes ergonomics into consideration is highly appreciated. Note the slight hourglass shape of the tool, that really lets your hand take a grip that counters the natural tendency of the tool to turn with the rotation of the case, especially when turning with a power case driver. The size of the tool itself also helps; if you’ve used one of the smaller tools on the market, you know just how tired your hand can get from trying to hold on to it after a while! I turned 70 case necks in two sessions with the 21st Century tool and my hand and fingers remained comfortable throughout.
However good the turner may be, it doesn’t work alone. Any neck turner needs a matching expander. The 21st Century expander is a nicely designed unit that allows you to change expander sizes with no tools by simply unscrewing the cap of the die body and dropping in the appropriate expander.
K&M Arbor Adapters Available
I’ve been using a K&M turner for some years now and have accumulated turning arbors (mandrels) in various sizes. John knows that’s the case for many of us, so he makes affordable adapter bushings for his tool that allow the use of K&M turner arbors. That’s a nice feature that will allow me to save the price of a few arbors and expanders. The adapter for K&M arbors costs $12.00.
Although I use a cordless screwdriver to turn the case, I still like to have a manual option for case turning. Sometimes the cordless driver dies with just a few cases left to go in a session and I know that, one day, when I most need it, it’ll just quit altogether. John’s case handle for manual case turning is another well-designed, ergonomic piece that shows his careful, thoughtful approach to tool design. He even makes a version of it for the .50 BMG if your tastes in cartridges run on the large side!
Neck-Turning Tool and Accessory Order Information
Order the Neck Turner and accessories through www.21stCenturyShooting.com, or call (260) 273-9909. The 21st Century neck-turning tool, by itself, costs $78.00, including a carbide cutter (standard size). You can chose among four different cutter shoulder angles, to match your particular cartridge: 20°, 30°, 35°, and 40°. Additional carbide cutters cost $26.00-$28.00. Caliber-specific turning arbors and expander mandrels are priced at $7.95 each. The standard size Universal Case-Holding Handle (photo above), costs $16.95.
You can also purchase a complete Neck-Turning Tool Kit from 21st Century. This $112.99 package includes everything you need:
Neck Turning Tool w/cutter
Turning Arbor
Expander Mandrel
Expander Die Body
Loading Die Locking Ring
Neck Turning Universal Handle
Disclosure: 21st Century Shooting, an advertiser on this website, provided a neck turner tool and accessories to German Salazar for testing and evaluation.
Share the post "NEW Neck-Turning Tool From 21st Century Shooting"
K&M Precision Shooting Products has two very handy products you may not know about yet. The first, a brilliantly simple device that lets you see your case necks as you expand them, can be used by anyone who necks-up brass (with a compatible expander die body). The second new product is a specialized “fat grip” holder that will make neck-turning easier for those of you out there who use K&M neck-turners.
K&M Expand Mandrel Window Riser
Ergo Holder for K&M Neck-Turning Tool
Turn Necks in a Single Pass
Why does the 21st Century Neck-Turning Tool cut so well? First, the Neck-Turning Tool employs ultra-sharp carbide cutters that are custom-ground to fit the shoulder angle of your cartridge. This allows you to make a perfect cut extending down the shoulder 1/32 of an inch. Second, the system aligns the case neck on the arbor (mandrel) so well, and the cutter is so sharp, that very little torque is required. This allows the cutting process to go very smoothly. The case-holder is also unique — it features a O-ring so it holds the case firmly in place without marring or bending the case head. The tailstock case-holder adjusts to accommodate cases from 17 Fireball to a .416 Rigby.
From PMA’s website I learned that this turner does NOT use a coarse or fine drive screw to move the cutter towards or away from the mandrel. Nor does the PMA tool move the mandrel on an eccentric (another method of cutting depth control). The PMA tool does something very different. PMA’s Model A Neck Turning Tool simply adjusts by moving the mandrel toward or away from the stationary cutter with an 80 TPI drive screw with 60 indicating marks. Each mark moves the mandrel .0002″ (two ten-thousandths). I found, if you stop between the marks, .0001″ isn’t out of the question. It’s such a smart arrangement, I wondered “why didn’t anyone think of that before?”
Turning necks is tedious, especially if you’re turning a large number of cases as High Power shooters generally do. Accordingly, a design that takes ergonomics into consideration is highly appreciated. Note the slight hourglass shape of the tool, that really lets your hand take a grip that counters the natural tendency of the tool to turn with the rotation of the case, especially when turning with a power case driver. The size of the tool itself also helps; if you’ve used one of the smaller tools on the market, you know just how tired your hand can get from trying to hold on to it after a while! I turned 70 case necks in two sessions with the 21st Century tool and my hand and fingers remained comfortable throughout.
