As an Amazon Associate, this site earns a commission from Amazon sales.











December 30th, 2020

REMAGE Pre-Fit 6mmBR Conversion — How to Do It

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr
Barrel nut system allows “Pre-Fit” barrel installation on a Remington action. CLICK photo to zoom.

REMAGE Project Report by Bill, Rifleshooter.com Editor
Installing a new barrel on your Remington 700 (especially without a lathe) may seem like a daunting task, but thanks to companies like McGowen Precision Barrels and Criterion, there are easier alternatives. By adopting a Savage-style barrel nut on a 1 1/16″ thread for a Remington 700 receiver, pre-chambered (aka “pre-fit”) barrels can be easily swapped with just a few hand tools. This system is sometimes called a REMAGE conversion (for “REMington savAGE”). With simple tools a “Pre-fit” 6mmBR-chambered barrel was installed on the author’s Remington action — no machining or lathe-work required.

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr

Using a few tools from Brownells: Remington 700 Action Wrench, Barrel Vise, Go and No-Go Gauges, Recoil Lug Alignment Tool, and a Savage Barrel Nut Wrench, I was able to swap the .308 Winchester barrel off of my Remington 700 short action and install the new McGowen pre-fit, pre-chambered barrel, converting it to a tack-driving 6BR (aka 6mmBR Norma).

The existing barrel is simply removed from the action (normally the hardest part) and the new barrel is screwed on with the Go Gauge in place. After headspace is verified with the Go Gauge, the barrel nut is tightened against the action and you are off to the range. It takes all of the machine work out of the barreling process.

Note: Because barrel nut has a slightly larger diameter, some stocks may require minor inletting. Also, if you are shooting fired brass from another rifle with the same chambering, you should FL-size the brass before loading it for your new pre-fit barrel. And always check the set-up with a dummy round loaded to normal cartridge length BEFORE you head to the range. With Pre-Fits, the freebore should be adequate for your cartridge, but always check and adjust your seating depth as needed.

remage 6mm BR 108 berger best group 360

My McGowen Remage barrel looks and shoots great. I’ve written two longer articles that provide greater detail about this project. To learn more about how the barrel was installed, read: Rebarrel a Remington 700 without a lathe: McGowen’s Remage barrel conversion. To see how the rifle performed at the range, read: McGowen Remage Barrel Review: Spoiler Alert — It Shoots!.

Bill has been a serious shooter for over 20 years. A former Marine Corps Sergeant, he’s competed and placed in High Power Rifle, ISPC, USPSA, IDPA, 3-Gun, F-Class, and precision rifle disciplines. In addition to being an NRA-certified firearms instructor and range officer, Bill has hunted big game in North America, South America, and Africa. Bill writes extensively about gunsmithing, precision rifles, and the shooting sports on his Rifleshooter.com website.

Permalink Gear Review, Gunsmithing, Tactical No Comments »
November 13th, 2020

Criterion Barrel — Great Accuracy with Creedmoor Sports Ammo

criterion barrel black creedmoor sports .308 Win Ammunition ammo

Superb Accuracy with Criterion Pre-Fit Barrel and Creedmoor Sports Ammo
Check out that 0.188″ group. Can you believe that was shot with factory .308 Win ammo? A while back our friends at Criterion Barrels tested some .308 ammo from Creedmoor Sports. This was loaded with Lapua’s 175gr Scenar HPBT bullet in Lapua brass. The results speak for themselves. Any time factory ammo can shoot inside quarter-MOA, that’s impressive. This ammo was used in a “Rem/Age” project rifle. That term refers to a Remington action rifle that has been re-barreled with a pre-fit Criterion barrel. The new barrel is secured with a Savage-style barrel nut. Hence the term “Rem/Age” or “Rem-Age”.

shooting target accurateshooter load developmentCriterion posted: “I think we may have a new favorite factory match load for the nitrided Rem/Age build.” Another reader added: “[Creedmoor’s] 175 Scenar .308 ammunition is top notch.” FYI, this group was shot on our load development target, which you can download for free from our Targets Page.

Why do Criterion barrels shoot so well? One reason is that Criterion’s barrel steel is carefully stress-relieved. In the photo below, Criterion Rack 1A (aka the “Coffin”) has been loaded with barrel blanks — made ready for the stress-relieving process.

criterion barrel black creedmoor sports .308 Win Ammunition ammo

Working with Pre-Fit Barrels
While they may require the purchase of some additional tools and a bit of a learning curve to install, using Rem/Age pre-fit barrels offer advantages over gunsmith chambering and barrel-fitting. In this video, 8541 Tactical explains how to install a Criterion 6.5 Creedmoor “pre-fit” barrel. You save money and time — you don’t have to wait for a gunsmith to chamber the barrel. While Criterion recommends that a competent gunsmith oversee the pre-fit installation, if you understand the use of go/no-go gauges and you have a barrel vise and action wrench set up to remove the original barrel, putting on a pre-fit barrel CAN be a DIY project. You don’t have to pack up your rifle to ship it off to a smith.

Permalink - Videos, Bullets, Brass, Ammo, Gear Review, Gunsmithing 3 Comments »
January 23rd, 2020

The “Remage” Project — Building Rem 700 with Pre-Fit Barrel

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr
Barrel nut system allows “Pre-Fit” barrel installation on a Remington action. CLICK photo to zoom.

REMAGE Project Report by Bill, Rifleshooter.com Editor
Installing a new barrel on your Remington 700 (especially without a lathe) may seem like a daunting task, but thanks to companies like McGowen Precision Barrels, there are easier alternatives. By adopting a Savage-style barrel nut on a 1 1/16″ thread for a Remington 700 receiver, pre-chambered (aka “pre-fit”) barrels can be easily swapped with just a few hand tools. This system is sometimes called a REMAGE conversion (for “REMington savAGE”). With simple tools a “Pre-fit” 6mmBR-chambered barrel was installed on the author’s Remington action — no machining or lathe-work required.

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr

Using a few tools from Brownells: Remington 700 Action Wrench, Barrel Vise, Go and No-Go Gauges, Recoil Lug Alignment Tool, and a Savage Barrel Nut Wrench, I was able to swap the .308 Winchester barrel off of my Remington 700 short action and install the new McGowen pre-fit, pre-chambered barrel, converting it to a tack-driving 6BR (aka 6mmBR Norma).

The existing barrel is simply removed from the action (normally the hardest part) and the new barrel is screwed on with the Go Gauge in place. After headspace is verified with the Go Gauge, the barrel nut is tightened against the action and you are off to the range. It takes all of the machine work out of the barreling process.

Note: Because barrel nut has a slightly larger diameter, some stocks may require minor inletting. Also, if you are shooting fired brass from another rifle with the same chambering, you should FL-size the brass before loading it for your new pre-fit barrel. And always check the set-up with a dummy round loaded to normal cartridge length BEFORE you head to the range. With Pre-Fits, the freebore should be adequate for your cartridge, but always check and adjust your seating depth as needed.

remage 6mm BR 108 berger best group 360

My McGowen Remage barrel looks and shoots great. I’ve written two longer articles that provide greater detail about this project. To learn more about how the barrel was installed, read: Rebarrel a Remington 700 without a lathe: McGowen’s Remage barrel conversion. To see how the rifle performed at the range, read: McGowen Remage Barrel Review: Spoiler Alert — It Shoots!.

Bill has been a serious shooter for over 20 years. A former Marine Corps Sergeant, he’s competed and placed in High Power Rifle, ISPC, USPSA, IDPA, 3-Gun, F-Class, and precision rifle disciplines. In addition to being an NRA-certified firearms instructor and range officer, Bill has hunted big game in North America, South America, and Africa. Bill writes extensively about gunsmithing, precision rifles, and the shooting sports on his blog, Rifleshooter.com.

Permalink Gear Review, Gunsmithing, Tech Tip No Comments »
April 9th, 2019

Don’t Waste Time (and Ammo) on a Poor Factory Barrel

Savage Criterion BarrelIn our Shooters’ Forum, you’ll find a lengthy thread about accuracy problems with a Savage LRPV, chambered in 6mmBR. The gun would repeatedly split groups at 100 yards, and at 300 yards, the “flyers” would open up the groups to 1.5 MOA or larger. Interestingly, the factory test target (at right) showed a split group — not a good sign.

The gun’s owner, forum member LR_Shooter, tried a variety of tweaks: “I did this, done that… [changed] torque, tang floated, bedded action, recut chamber, and [adjusted firing pin]”. But nothing really helped. Frustrated, LR_Shooter asked his fellow Forum members for help. Much advice was proffered, including the novel idea of removing the middle action screw in the Savage 3-screw target action. Some of the advice proved helpful, but none of the suggested remedies produced a major improvement. This rifle, out of the box, tossed flyers and no amount of tweaking (or changes in shooting technique) really cured the basic problem. That is, until, the factory barrel got replaced…

Savage Criterion Barrel

New Criterion Pre-Fit Barrel Works Wonders
LR_Shooter acquired a Criterion pre-fit barrel from Jim Briggs at Northland Shooters Supply (NSS). These pre-fits are designed for easy installation with the standard Savage barrel nut. Wouldn’t you know it, with a new 30″ heavy-contour barrel on the LRPV, the gun started shooting way better. No more crazy fliers, no more split groups, no more excessive vertical. And the improvement came without any other major modifications.

LR_Shooter reports: “I got a replacement barrel from Jim at NSS. It is a 30″ bull Criterion barrel. So far, without playing with torque screws and having my old setup… I’m very satisfied with the barrel I got. Now I have no problem getting [groups] under 0.25 MOA. Finally this thing can shoot!”

Targets Shot with Savage LRPV Fitted with Criterion Barrel
Savage Criterion Barrel

The targets above, shot with the new Criterion barrel, speak for themselves. The left target was shot at 100 yards, while the target on the right was shot at 300 yards (very impressive).

Moral of the Story — Sometimes A New Barrel Really Is the Right Solution
All of us have struggled at times with a rifle that won’t live up to expectations. This Editor personally struggled for over a year with a .260 Rem Savage with a factory tube. The gun tended to split groups and the POI walked as the barrel heated. I tried one powder/primer combination after another, working through a variety of seating depths over many months. I was persistent. Out of stubbornness, I just believed that sooner or later I’d find the magic load.

Well folks, sometimes there’s really nothing you can do about a sub-par barrel. It is what it is. To really improve a gun’s accuracy (particularly a gun with a factory tube), you may need to open your wallet and get a quality aftermarket barrel. Spending months trying one recipe after another may simply be an overwhelming waste of powder, bullets, and your precious time.

Albert Einstein supposedly said: “Insanity is defined as doing the same thing over and over again, and expecting different results.” Well that sort of describes my efforts with my .260 Rem. Once I had enough evidence that my barrel split groups no matter what load combo (and seating depth) I tried, it was time to pony up for a new barrel. When I did finally screw on a nice PacNor 3-groove Supermatch, that Savage suddenly became a true tack-driver. As re-chambered in 6mmBR with the Pac-Nor, in calm conditions, my Savage will now consistently shoot in the twos with heavy bullets, and it can sometimes dip down into the ones with Berger 80gr flat-base bullets. The moral of the story here is simple — don’t waste weeks or months chasing your tail with a barrel that just won’t deliver (after a reasonable amount of testing). Save up for a custom barrel, get it chambered properly, and stop your cycle of frustration.

Contact Information for Northland Shooters Supply:
Northland Shooters Supply
10720 Rose Drive
Bismarck, ND 58503

Email: james@northlandshooterssupply.com
Website: Northlandshooterssupply.com
Telephone: (763) 682-4296; Fax: (763) 682-6098

Permalink Gear Review, Gunsmithing, Tech Tip 4 Comments »
September 9th, 2018

“REMAGE” Remake — Converting Remington to Barrel Nut System

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr
Barrel nut system allows “Pre-Fit” barrel installation on a Remington action. CLICK photo to zoom.

REMAGE Project Report by Bill, Rifleshooter.com Editor
Installing a new barrel on your Remington 700 (especially without a lathe) may seem like a daunting task, but thanks to companies like McGowen Precision Barrels, there are easier alternatives. By adopting a Savage-style barrel nut on a 1 1/16″ thread for a Remington 700 receiver, pre-chambered (aka “pre-fit”) barrels can be easily swapped with just a few hand tools. This system is sometimes called a REMAGE conversion (for “REMington savAGE”). With simple tools a “Pre-fit” 6mmBR-chambered barrel was installed on the author’s Remington action — no machining or lathe-work required.

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr

Using a few tools from Brownells: Remington 700 Action Wrench, Barrel Vise, Go and No-Go Gauges, Recoil Lug Alignment Tool, and a Savage Barrel Nut Wrench, I was able to swap the .308 Winchester barrel off of my Remington 700 short action and install the new McGowen pre-fit, pre-chambered barrel, converting it to a tack-driving 6BR (aka 6mmBR Norma).

The existing barrel is simply removed from the action (normally the hardest part) and the new barrel is screwed on with the Go Gauge in place. After headspace is verified with the Go Gauge, the barrel nut is tightened against the action and you are off to the range. It takes all of the machine work out of the barreling process.

Note: Because barrel nut has a slightly larger diameter, some stocks may require minor inletting. Also, if you are shooting fired brass from another rifle with the same chambering, you should FL-size the brass before loading it for your new pre-fit barrel. And always check the set-up with a dummy round loaded to normal cartridge length BEFORE you head to the range. With Pre-Fits, the freebore should be adequate for your cartridge, but always check and adjust your seating depth as needed.

remage 6mm BR 108 berger best group 360

My McGowen Remage barrel looks and shoots great. I’ve written two longer articles that provide greater detail about this project. To learn more about how the barrel was installed, read: Rebarrel a Remington 700 without a lathe: McGowen’s Remage barrel conversion. To see how the rifle performed at the range, read: McGowen Remage Barrel Review: Spoiler Alert- It Shoots!.

Bill has been a serious shooter for over 20 years. A former Marine Corps Sergeant, he’s competed and placed in High Power Rifle, ISPC, USPSA, IDPA, 3-Gun, F-Class, and precision rifle disciplines. In addition to being an NRA-certified firearms instructor and range officer, Bill has hunted big game in North America, South America, and Africa. Bill writes extensively about gunsmithing, precision rifles, and the shooting sports on his blog, Rifleshooter.com.

Permalink - Articles, Gunsmithing 1 Comment »
August 28th, 2018

Remington Pre-Fit Barrels with Savage-Style Barrel Nut

Mcree Precision Mcrees Savage Remington pre-fitted pre-chambered pre-fit barrel system kit nut
McRee’s Precision Remington DIY Barrel Kit includes Criterion Pre-Fit Stainless Barrel, Barrel Nut, Recoil Lug, Thread Protector, and Barrel Nut Wrench:

Need a new barrel for your Rem-actioned hunting or tactical rifle? Here’s a great DIY option for riflemen. McRee’s Precision offers complete, no-gunsmithing re-barreling kits for Remington and Rem-clone actions. These feature a high-quality, pre-chambered “PRE-FIT” stainless barrel from Criterion, a Savage-style barrel nut, a recoil lug, and a special barrel-nut wrench. Most of the Pre-Fit barrels are 24″ long and threaded at the muzzle. CLICK Here for all Pre-Fit barrel specs.

With this system you can easily re-barrel your favorite Remington rifle yourself in less than an hour. You don’t need to pay gunsmithing fees, or wait weeks (or months) for a busy smith to do the job. And the price is under $500.00. Kits are currently available for these chamberings: 6.5 Creedmoor, 6mm Creedmoor, .243 Win, .308 Win, .308 Winchester Magnum. You can buy with confidence — McRee’s Precision offers a Half-MOA Accuracy Guarantee with its pre-fitted barrel kits.

Mcree Precision Mcrees Savage Remington pre-fitted pre-chambered pre-fit barrel system kit nut
The stainless steel Barrel Nut is set up for 1 1/16 x 16 barrel threads, while the stainless steel recoil lug has a 1/8 inch removable locator pin and is set up for 1.0625 dia barrel threads.

McRee’s Precision sells Rem-action Pre-Fit barrel packages (complete with barrel nut, recoil lug, and wrench) starting at $489.52. Choose from five chamberings: 6.5 Creedmoor, 6mm Creedmoor, .243 Win, .308 Win, and .300 Win Mag. These Pre-Fit barrel kits come ready-to-install. All you need to do is remove your current barrel, place the recoil lug, spin on the new tube, follow the instructions for setting head-space with standard go/no-go gauges, then torque the barrel nut against the lug. NOTE: You may require a barrel vise and action wrench to remove the original barrel. Chambering-specific headspace gauges required. Minor inletting changes may be needed forward of the action.

Mcree Precision Mcrees Savage Remington pre-fitted pre-chambered pre-fit barrel system kit nut

The folks at McRee’s Precision say their Pre-Fit system offers many advantages: “Remington Pre-Fitted Barrel Kits have become popular over the years. If Savage can do it, why not for our Remingtons? Our [Criterion-supplied] barrels are spec’d to the McRee standard of performance. There are several places to get the tools required to remove your factory barrel correctly. Once you have your barrel removed all you have to do is follow the normal Savage procedure to install your new barrel. We recommend that you contact your local gunsmith for the install. Feel free to call us with any questions.”

Product Tip from Ed LongRange. We welcome readers’ submissions.
Permalink Gear Review, Gunsmithing, Tech Tip No Comments »
May 13th, 2017

Tikka TECH — Criterion Pre-Fit Barrels Coming Soon for Tikka T3

Tikka T3 T-2 prefit chambered barrel 6.5 Creedmoor Solid Accuracy Criterion Barrels

We have always liked Tikka actions, and now there is a great re-barreling option for Tikka T3 owners. Criterion Barrels Inc. (CBI), makers of “pre-fit” barrels for Savage, Remington, and Rem-clone actions, will soon be offering Tikka pre-fits. These pre-chambered barrels for Tikka T3 actions will be headspaced with a barrel nut, just like a Savage.

Tikka T3 T-2 prefit chambered barrel 6.5 Creedmoor Solid Accuracy Criterion Barrels
Click image for full-screen version

The new Tikka T3 pre-fit barrels will be sold through Solid Accuracy, a respected Texas-based outfit that sells high-end scopes, stocks, barrels and other rifle components. Criterion tells us: “The Solid Accuracy barrel nut and wrench design has been finalized, the prototype barrels tested and the barrel nuts are now going through production (with an expected ETA of 2-3 weeks). All orders for these pre-fits barrels are currently heading out to the shop floor for production. Orders placed this week can expect a conservative estimated lead time of 14-16 weeks.”

The accuracy has been impressive with Solid Accuracy’s test rifle, which features a Tikka T3 action mounted in a KRG X-Ray chassis. This prototype rifle is chambered in 6.5 Creedmoor. The group below was shot with a stout load of H4350 and Sierra 140 grain MatchKings seated .009″ in the lands.

Tikka T3 T-2 prefit chambered barrel 6.5 Creedmoor Solid Accuracy Criterion Barrels

The folks at Criterion are excited about the Tikka pre-fit project: “We’re looking forward to getting these barrels out the door and on to some custom rifle builds.” One of Criterion’s staffers was so impressed with the initial test results that he is building his own T3 project, with a Criterion pre-fit of course…

Permalink Gunsmithing, New Product, Tactical 4 Comments »
November 22nd, 2016

Pre-Fit DIY Barrel System for Remington-Type Actions

Mcree Precision Mcrees Savage Remington pre-fitted pre-chambered pre-fit barrel system kit nut

Need a new barrel for your Rem-actioned hunting or tactical rifle? Here’s a great DIY option for riflemen. McRee’s Precision offers complete, no-gunsmithing re-barreling kits for Remington and Rem-clone actions. These feature a high-quality, pre-chambered “PRE-FIT” stainless barrel from Criterion, a Savage-style barrel nut, a recoil lug, and a special barrel-nut wrench. With this system you can easily re-barrel your favorite Remington rifle yourself in less than an hour. You don’t need to pay gunsmithing fees, or wait weeks (or months) for a busy smith to do the job. And the price is under $500.00. McRee’s Precision even offers a Half-MOA Accuracy Guarantee with its pre-fitted barrel kits. NOTE: Check MrReesPrecision.net on Thanksgiving for a Holiday Special Price (probably 10% Off).

McRee’s Precision Remington DIY Barrel Kit includes Criterion Pre-Fit Stainless Barrel, Barrel Nut, Recoil Lug, Thread Protector, and Barrel Nut Wrench:
Mcree Precision Mcrees Savage Remington pre-fitted pre-chambered pre-fit barrel system kit nut
The stainless steel Barrel Nut is set up for 1 1/16 x 16 barrel threads, while the stainless steel recoil lug has a 1/8 inch removable locator pin and is set up for 1.0625 dia barrel threads. Barrel Kit Specifications.

McRee’s Precision sells Rem-action Pre-Fit barrel packages (complete with barrel nut, recoil lug, and wrench) starting at $499.52 (get a Holiday Discount on that price commencing 11/24/2016). Choose from five chamberings: .243 Win, 6.5 Creedmoor, .260 Rem, .308 Win, and .300 Win Mag. These Pre-Fit barrel kits are “100% complete and ready-to-install”. All you need to do is remove your current barrel, place the recoil lug, spin on the new tube, follow the instructions for setting head-space, then torque the barrel nut against the lug. NOTE: You may require a barrel vise and action wrench to remove the original barrel. Minor inletting changes may be needed forward of the action.

The folks at McRee’s Precision say their Pre-Fit system offers many advantages: “Remington Pre-Fitted Barrel Kits have become popular over the years. If Savage can do it, why not for our Remingtons? Our [Criterion-supplied] barrels are spec’d to the McRee standard of performance. There are several places to get the tools required to remove your factory barrel correctly. Once you have your barrel removed all you have to do is follow the normal Savage procedure to install your new barrel. We recommend that you contact your local gunsmith for the install. Feel free to call us with any questions.”

Product Tip from Ed LongRange. We welcome readers’ submissions.
Permalink Gear Review, Gunsmithing No Comments »
July 9th, 2015

6mmBR “REMAGE” Conversion by Rifleshooter.com

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr
Barrel nut system allows “Pre-Fit” barrel installation on a Remington action. CLICK photo to zoom.

REMAGE Project Report by Bill, Rifleshooter.com Editor
Installing a new barrel on your Remington 700 (especially without a lathe) may seem like a daunting task, but thanks to companies like McGowen Precision Barrels, there are easier alternatives. By adopting a Savage-style barrel nut on a 1 1/16″ thread for a Remington 700 receiver, pre-chambered (aka “pre-fit”) barrels can be easily swapped with just a few hand tools. This system is sometimes called a REMAGE conversion (for “REMington savAGE”).

Remage Savage Remington Rebarrel Rifleshooter.com 6BR 6mmbr

Using a few tools from Brownells: Remington 700 Action Wrench, Barrel Vise, Go and No-Go Gauges, Recoil Lug Alignment Tool, and a Savage Barrel Nut Wrench, I was able to swap the .308 Winchester barrel off of my Remington 700 short action and install the new McGowen pre-fit, pre-chambered barrel, converting it to a tack-driving 6BR (aka 6mmBR Norma).

The existing barrel is simply removed from the action (normally the hardest part) and the new barrel is screwed on with the Go Gauge in place. The barrel nut is tightened against the action, headspace verified with the Go Gauge, and you are off to the range. It takes all of the machine work out of the barreling process. Note: the barrel nut has a slightly larger diameter and some stocks may require minor inletting. Also if you are shooting fired brass from another rifle with the same chambering, you should FL-size the brass before loading it for your new pre-fit barrel.

remage 6mm BR 108 berger best group 360

My McGowen Remage barrel looks and shoots great. I’ve written two longer articles that provide greater detail about this project. To learn more about how the barrel was installed, read: Rebarrel a Remington 700 without a lathe: McGowen’s Remage barrel conversion. To see how the rifle performed at the range, read: McGowen Remage Barrel Review: Spoiler Alert- It Shoots!.

Bill has been a serious shooter for over 20 years. A former Marine Corps Sergeant, he’s competed and placed in High Power Rifle, ISPC, USPSA, IDPA, 3-Gun, F-Class, and precision rifle disciplines. In addition to being an NRA-certified firearms instructor and range officer, Bill has hunted big game in North America, South America, and Africa. Bill writes extensively about gunsmithing, precision rifles, and the shooting sports on his blog, Rifleshooter.com.

Permalink - Articles, Gunsmithing 1 Comment »