Discharging a .338 Lapua Magnum round with a cleaning rod in the barrel — that’s a recipe for disaster. What happens when a fired .338 caliber bullet and a cleaning rod try to occupy the same place at the same time? Well you get a catastrophic kaboom, with metal pieces flying all over the place, and a shooter very lucky to escape without serious injury. This incident occurred recently in Manatee, Florida, as reported by Sniper’s Hide member Queequeg. We thank SnipersHide.com for granting permission to publish these revealing images in the Daily Bulletin. CLICK HERE for more Kaboom info on the ‘Hide.
This story should serve as a chilling reminder to follow proper safety practices whenever you are at the range. Always check to make sure there is no obstruction in the bore BEFORE loading a live round.
.338 Lapua Magnum + Cleaning Rod + Inattention = Kaboom!
Click to zoom image
Kaboom at Manatee!
Sniper’s Hide member Queequeg recently published shocking photos of a catastrophic kaboom involving a .338 Lapua Magnum (Savage action). The action was blown off the rifle, shrapnel went through the roof, and the barrel split at the tenon before taking an excursion downrange. The action did crack in the front but the lugs remained engaged so the bolt did not slam to the rear (luckily for the shooter).
Here’s the report: “This happened [January 20, 2014] at the Manatee Gun and Archery Club. Al, Ren and myself were there with a couple other folks. Ren was at bench 12, I was at 13. The fellow at 11 was running a Savage .338 Lapua. He had a very bad day! He damn sure could have killed himself and quite likely Ren as well.”
Queeqeg added: “After the boom, I heard Ren ask ‘Are you alright’ and then turned to look in time to see the fellow reacting in total shock — literally stunned. Ren and I went over to him and could not see any major injuries. Ren was uninjured as well but had a lot of fiberglass splinters on him. The barrel nut is what I presume punched the two holes in the roof. The shooter is a regular there[.] He had been having a problem with sticky cases though he said he was certain the loads were mild. That’s why he was content to knock the sticky ones out with the rod. He simply forgot to remove the rod after knocking out the last stuck case. You can see what happened next.”
To learn more about this incident, go to the original Snipers Hide Forum Thread. There you’ll find more details and over four pages of related discussions.
The Important Lesson Here
What did the .338 LM shooter do wrong here? You will say — “Well that’s obvious, he left a cleaning rod in the barrel and then shot a round.” Yes, that was a potentially fatal error. But that was his second mistake — one that occurred only because he made a more fundamental judgment error first.
The FIRST mistake was not acknowledging the problem with his ammo. Had he heeded the warning signs, he would still have a rifle (and an unsoiled pair of trousers). When he first observed that he was having problems with extracting cases, a warning light should have gone off in his head. Presuming his extractor was not broken (and that the chamber was cut properly) he should have been able to extract his brass if he was running safe loads. The lesson here we all need to learn is that if you observe a serious ammo-related issue, it is time to stop shooting. Don’t try to invent work-arounds just to extend your range session, when there are clear signs that something is wrong, very wrong.
Thompson/Center Arms (T/C) has identified a condition that may cause the safety lever on certain ICON®, VENTURE™ and DIMENSION® rifles to bind, preventing the safety from becoming fully engaged. In this situation, closing the bolt may move the safety to the fire position. The rifle will not fire unless the trigger is pulled. Though there should be no risk of the gun going off by itself, T/C states: “Out of an abundance of caution, we are taking this action to recall the rifles so that the firearm can be inspected by our technicians to ensure that the safety lever functions as designed.”
This is a large-scale recall, not just a few rifles. This recall applies to all Icon, Venture, and Dimension rifles manufactured by Thompson/Center Arms prior to June 13, 2013. If you own a rifle affected by this recall, T/C recommends that you stop using the rifle and return it to T/C at once: “Because the safety of our customers is our utmost concern, we ask that you stop using your rifle until we have an opportunity to inspect the safety lever to ensure its proper function.”
To facilitate the inspection and repair, if necessary, of your rifle safety lever, contact Thompson/Center’s customer service department to receive instructions and a pre-paid shipping label for the return of your rifle to the factory. At no cost to the owner, T/C will repair the rifle and ship it back. For more information, visit www.tcarms.com. If you have any questions about this recall, contact Thompson/Center at (800) 713-0355.
Olin’s Winchester Division has issued a Recall Notice for one (1) lot of its 5.56x45mm M855 62 grain PENE centerfire rifle ammunition. This notice applies only to Symbol Number ZGQ3308 with Lot Number WCC10M106-004. Other Symbol Numbers or Lot Numbers are not subject to this recall.
Symbol Number: ZGQ3308
Lot Number: WCC10M106-004
Winchester states: “Through extensive evaluation Winchester has determined the above lot of 5.56mm M855 ammunition may contain incorrect propellant. Incorrect propellant in this ammunition may cause firearm damage, rendering the firearm inoperable, and subject the shooter or bystanders to a risk of serious personal injury when fired.”
The ammunition Symbol Number and Lot Number are ink stamped on the outside of the 900-round shipping container, and on the outside of the 30-round carton as shown at right:
If you have Winchester Ammo with Symbol Number ZGQ3308 and Lot Number WCC10M106-004 immediately discontinue use and contact Winchester toll-free at 866-423-5224 for free UPS pick-up of the recalled ammunition. Upon receipt of your recalled ammunition, Winchester will ship replacement ammunition directly to you.
If you have any questions concerning this 5.56mm M855 ammunition recall please call toll-free 866-423-5224, write to Winchester (600 Powder Mill Road, East Alton, IL 62024 Attn: 5.56mm M855 Recall), or visit www.winchester.com.
Notice tip by EdLongrange. We welcome reader submissions.
The .223 WSSM and 6mmBR Disaster
Report by Dr. Jim Clary
Under most circumstances, shooters don’t have to worry about chambering the wrong cartridge into the wrong rifle. After all, the cartridges are well marked and we all know which rifle we are shooting on any given day. In many cases, incorrect cartridges cannot be chambered — larger cases will not fit in smaller chambers, for example. No problem! That being said, I can tell you that even an experienced, careful and normally safe shooter can make a mistake.
The following is an account of just such a mistake that could have resulted in death or dismemberment. Fortunately, the shooter was not hurt, but the rifle was completely destroyed.
Last year, a friend purchased a Savage Precision right bolt, left port, single shot bolt action in 6mmBR Norma. It was an incredible prairie dog gun and he spent the summer burning powder and busting dogs. In October, he purchased a stainless steel Browning A-Bolt Varmint in .223 WSSM. The weather in the upper Midwest turned sour by the time he got the brass tuned up and he only got to fire it a few times before he was “socked in” for the winter. Thus, he spent his evenings loading ammo for the spring thaw.
During a break in the weather, he grabbed both rifles and a couple of bags of .223 WSSM and 6mmBR cartridges and headed to the range to check out his new loads. In case you are not familiar, the 6mmBR is smaller in diameter and a mite shorter than the .223 WSSM. Because of this, it will chamber in a .223 WSSM, but the .243 caliber (6mm) bullet is too big for the .22 caliber bore. That is what happened to my friend.
The rest is history — when he squeezed the trigger, all hell broke loose. The entire bottom of the rifle blew out, including the magazine assembly. The explosion actually cut the stock into two pieces. However, the bolt held and amazing as it may seem, the .243 bullet was “swaged” right out of the .223 barrel.
6mmBR (left) and .223 WSSM (right) cartridges above the remains of Browning A-Bolt rifle.
One Small Mistake Is All It Takes
Now, realize that my friend has been shooting all manner of firearms, safely, for over half a century. He is meticulous, thorough and conscientious in his approach to reloading and shooting. However, he made one mistake. He put some lose 6BR cartridges in a baggie as he packed up from a prairie dog hunt last summer, without noticing that the baggie was marked .223 WSSM in black marker. Then, when the break in his winter weather came, he grabbed the bag, believing it to be the WSSM cartridges and didn’t check the head stamp.
Couldn’t happen to you? How many times have we emptied our pockets of cartridges and dropped them into a plastic container on the shooting bench? How many times have we set down to a marathon reloading session, loading several calibers in a row? How many times have we put the wrong bullets, cases or primers into the incorrect container? My point is that even the safest of us can make a mistake. So, look at the picture above and take a bit more time when you reload your ammunition at home or chamber a round in the field. It might save your life.
On his Riflemans’ Journal blog, German Salazar wrote an excellent article about cartridge Case-Head Separation. We strongly recommend that you read this article. German examines the causes of this serious problem and he explains the ways you can inspect your brass to minimize the risk of a case-head separation. As cases get fired multiple times and then resized during reloading, the cases can stretch. Typically, there is a point in the lower section of the case where the case-walls thin out. This is your “danger zone” and you need to watch for tell-tale signs of weakening.
The photo below shows a case sectioned so that you can see where the case wall becomes thinner near the web. German scribed a little arrow into the soot inside the case pointing to the thinned area. This case hadn’t split yet, but it most likely would do so after one or two more firings.
One great tip offered by German Salazar involves using a bent paper clip to detect potential case wall problems. Slide the paper clip inside your case to check for thin spots. German explains: “This simple little tool (bent paper clip) will let you check the inside of cases before you reload them. The thin spot will be immediately apparent as you run the clip up the inside of the case. If you’re seeing a shiny line on the outside and the clip is really hitting a thin spot inside, it’s time to retire the case. If you do this every time you reload, on at least 15% of your cases, you’ll develop a good feel for what the thin spot feels like and how it gets worse as the case is reloaded more times. And if you’re loading the night before a match and feel pressured for time — don’t skip this step!”
The National Shooting Sports Foundation (NSSF) has produced a GUN SAFETY Video that presents 10 fundamental rules of safe gun use. The video covers basic safe gun handling procedures, and it also explains how to transport guns safely, and how to secure them properly at home.
We know this stuff is familiar to most of our readers, but we recommend you watch the video as a refresher. Segments show how to safely unload different types of handguns and shotguns. That’s helpful for a rifle guy who may not have much familiarity with other types of arms. The video also explains how you can keep a handgun safe from kids and guests in the home, while still having quick access in an emergency. This video won’t win an Oscar, but it provides good, logical safety advice. If you help run a shooting club, you may want to embed the video into your club’s webpage.
Remington has announced that it is recalling four (4) lots of Remington .338 Lapua Magnum ‘Express Rifle’ Ammunition. The recalled lots are: L13SA29L, L13SA29R, L13SB29L, and L13SB29R. The reason for the recall is that the listed lots “may have been improperly loaded. Improper loading may cause malfunctions which may result in damage to the firearm, serious personal injury or death.” CLICK HERE for more information, and to download PDF Recall Notice from Remington.
Fiocchi of America is recalling various lots of 22-250 Remington and .243 Winchester centerfire rifle ammunition. There is a serious safety issue affecting certain lots of Fiocchi ammo types: 22250B, 22250HVD, 243SPB, 243HSB, and 243SPD. The problem involves the loading of multiple bullets in a single cartridge. If you have any Fiocchi ammo from the affected product lots listed below you should return it immediately. The following ammunition products are affected by this recall:
Text of Fiocchi’s Recall Notice:
Through extensive evaluation Fiocchi has determined that the above lots of 22-250 and 243 may have been loaded with multiple bullets that can cause excessive pressure. This ammunition with multiple bullets may cause firearm damage rendering the firearm inoperable, and subject the shooter or bystanders to a risk of personal injury when fired. DO NOT USE THE ABOVE LISTED FIOCCHI 22-250 REM. OR 243 WIN. AMMUNITION OF SPECIFIED LOT NUMBERS. The ammunition lot number is black ink stamped inside one of the box end tuck flaps that you would open to remove the 20-round carrier.
To determine if your ammunition is subject to this notice, review the ITEM and LOT NUMBER. If the item number AND last three digits of the lot number match the above listed products, please return the ammunition to FIOCCHI of America via United Parcel Service (UPS) or FedEx Ground. Securely pack the ammo in a strong fiberboard box with packing materials to make it “snug” in the box. You will need an “LQ” label to ship the ammunition. To get the “LQ” label, [CLICK this LINK] or you can call the factory customer service directly at 417-449-1039 or email service@fiocchiusa.com prior to shipping. Affix the “LQ” label to the package with packing tape ensuring that all sides are adhered to the carton and ship to:
FIOCCHI OF AMERICA, INC., ATTN. Recall, 6930 N. FREMONT RD., OZARK, MO 65721
Fiocchi will provide replacement product upon receipt of your return. Please include your name, street address, phone number (required for return shipping), and email address with your return. Ammunition cannot be shipped to post office boxes.
This notice only applies to above listed Fiocchi 22-250 Rem. and 243 Win ammunition with the above lot numbers. If you have questions concerning this ammunition recall, please call customer service directly at 417-449-1039, write to the above address, email service@fiocchiusa.com, or visit our website, www.fiocchiusa.com.
Need help with your handgunning? Check out the NRA’s Basics of Pistol Shooting DVD. This $19.95 DVD covers the purchase, handling, cleaning, and storage of both revolvers and semi-automatic pistols along with marksmanship fundamentals. Computer animations provide an inside look at how revolvers and semi-automatics function. The Basics of Pistol Shooting DVD is intended for anyone interested in learning how to safely operate, clean and select a pistol for a variety of activities.
Produced as a training aid for NRA’s Basic Pistol and/or FIRST Steps Pistol Courses, the 60-minute DVD provides useful information for all handgun owners, not just novices. We also recommend that NRA Certified Pistol Instructors watch the DVD to familiarize themselves with the most current training methods and safety procedures. The DVD can be ordered through the NRA Program Materials Center or by calling 1-800-336-7402.
Peltor folding ‘Shotgunner’ ear muffs are on sale right now at Amazon.com. Available in red (#97013), dark green (#97012), or black (#97011), the muffs cost about $17.00, and you can get free shipping with an order over $25.00. That’s a good deal for a good product. This Editor owns two sets of these muffs. They are very lightweight and comfortable. Because they fit well, with gel foam cushions, they actually seem to work better than some big bulky muffs (with higher NRRs) that don’t seal so well.
Peltor’s Shotgunner muffs feature tapered ear domes, cutaway on the lower half for stock clearance. We have not found any other muffs on the market that allow a better cheek weld, with less interference with the comb on a riflestock. These muffs also fold up into a very compact package. You can keep one set in your range kit and a spare set in your vehicle for back-up or if a friend needs hearing protection.
USER REVIEW: Because I am a firearm instructor I own a half-dozen muffs including a pair of electronic Peltors. These [folding shotgunner muffs] are my favorite at 10% of the cost of electronic muffs. I bought them for trap/skeet. My Browning has an adjustable comb but these do NOT interfere with mounting the shotgun or getting a proper cheek weld as do the large electronic muffs. I highly recommend these to you. They are inexpensive but are EXTREMELY COMFORTABLE and WORK VERY WELL. What more could you ask? — F.M. (Idaho)
Ear Plugs vs. Muffs
Personally I prefer using foam earplugs, because they have a better Noise Reduction Rating (NRR) than the Shotgunner Muffs. However, there are times when the muffs come in handy, as when I am scoring for a fellow shooter and need to hear range instructions. I also like to keep a spare pair of muffs in my vehicle at all times. It always seems that, when we go to the range, someone forgets ear protection, or doesn’t like to use plugs.
For Indoor Use — Add Plugs Underneath
For indoor use, particularly on a tight firing line (with a guy shooting a .44 Mag right next to you), you’ll want muffs with a higher NRR. Alternatively, wear ear plugs under the muffs. Peltor Shotgunner folding muffs have a NRR of 21 db — compare that to 25-30 db NRR for big, heavy muffs and 29-33 db NRR for good ear plugs, such as the Howard Leight Max UF plugs (33 NRR). Of course, to achieve those 30+ Noise Reduction Ratings, earplugs must be inserted correctly.
Thompson/Center Arms (T/C) has identified a condition that may cause the safety lever on certain ICON®, VENTURE™ and DIMENSION® rifles to bind, preventing the safety from becoming fully engaged. In this situation, closing the bolt may move the safety to the fire position. The rifle will not fire unless the trigger is pulled. Though there should be no risk of the gun going off by itself, T/C states: “Out of an abundance of caution, we are taking this action to recall the rifles so that the firearm can be inspected by our technicians to ensure that the safety lever functions as designed.”
Winchester states: “Through extensive evaluation Winchester has determined the above lot of 5.56mm M855 ammunition may contain incorrect propellant. Incorrect propellant in this ammunition may cause firearm damage, rendering the firearm inoperable, and subject the shooter or bystanders to a risk of serious personal injury when fired.”
On his 
The 
Fiocchi of America is recalling various lots of 22-250 Remington and .243 Winchester centerfire rifle ammunition. There is a serious safety issue affecting certain lots of Fiocchi ammo types: 22250B, 22250HVD, 243SPB, 243HSB, and 243SPD. The problem involves the loading of multiple bullets in a single cartridge. If you have any Fiocchi ammo from the affected product lots listed below you should return it immediately. The following ammunition products are affected by this recall:
Need help with your handgunning? Check out the NRA’s 
Ear Plugs vs. Muffs
