As an Amazon Associate, this site earns a commission from Amazon sales.

July 27th, 2013

New WFT 2 Trimmer Adapts to Multiple Cartridge Types

Little Crow Gunworks has updated its popular “World’s Finest Trimmer” (aka WFT). The new WFT 2 version is more versatile — it can now easily change from one cartridge family type to another. That makes the $69.95 product an even better value. Trimming works the same way as before — just push the cartridge case into the trimmer and cut depth is pre-set. When ordering the WFT 2, choose a trim chamber for your particular cartridge family (such as .308, 7mm-08, .243 Win). You can trim multiple cartridge types (with one trim chamber) by ordering the largest chamber in the family you plan to trim. To trim cartridges from a different family, simply order (and install) a different chamber insert.

World's finest trimmer case trimming tool chamber insert WFT 2

The WFT 2’s designers explain: “The two main improvements are the ability to trim up to 45 caliber and interchange trim chambers. The WFT 2 has a half-inch shaft and requires a half-inch chuck to drive it. The feature most customers asked for was the ability to interchange trim chambers. After many prototypes (and much testing) the solution came from our friend, Jim Lambert. Instead of press-fitting the trim chambers, as on our original WFT, the trim chambers on our WFT 2 feature a slight slip-fit-in bearing with a groove cut for an O-ring which creates a press fit.”

How to Change Trim Chambers
Changing out trim chambers is accomplished by removing the cutter and pushing out the trim chamber with the knock-out dowel that is provided with the WFT 2. To install the trim chamber, set the trim chamber on a flat surface and steadily push the housing onto the trim chamber. To set cut depth (COAL trim length) place a ‘master case’ in the trim chamber and slide the cutter up to the case mouth. The tighten the set screws.

Product Tip from EdLongrange. We welcome reader submissions
Permalink New Product, Reloading 4 Comments »
February 16th, 2013

Gear Review: ‘World’s Finest Trimmer’ from Little Crow Gunworks

We had a chance to try out the new power case trimmer head from Little Crow Gunworks. Dubbed the “World’s Finest Trimmer” (WFT) by its inventor, Dale Hegstrom, this device proved fast, precise, and easy to use. When compared to a Hornady Lock ‘N Load hand-crank trimmer, the WFT processed cases twice as fast, and delivered a more uniform cut length with our test brass.

The WFT features a steel shell-holder, aluminum body, and steel drive shank. You can chuck it into any electric drill or power device that can handle the 3/8″ shank. Unlike most case trimming tools, the WFT indexes off the shoulder datum. This permits you to trim cases very quickly, without fiddling around with rim-grabbing collets, or shell-holders. Watch the videos to see the WFT in action.

World's Finest Trimmer

WFT is Fast and User-Friendly
Mark LaFevers, our tester, was easily able to trim five (5) cases in under 30 seconds. It took quite a bit longer to trim five cases with the Hornady trimmer he used for comparison. Mark noted that, after just a 20 or so manually-trimmed cases, his arm would start to fatigue. By contrast, he could effortlessly trim 100 or more cases with the WFT. For older folks with a bit of arthritis, the WFT makes life easier. Mark observed that the WFT produces a “nice, square, clean cut”, while offering a “very fast cycle rate”. He tells us, “once you get the hang of it, you probably can trim your brass two, if not three times as fast.”

Mark really liked the WFT tool, and a WFT will be replacing his hand trimmer for big jobs. One downside is that, currently, the WFT is cartridge specific — you normally need to have a different tool for each cartridge type you trim. And there are no swappable inserts allowing you to trim different cartridge types with the same tool. However some WFT versions WILL trim different cartridge types within the same “family”, such as .270 Win and .30-06.*

Hi-Rez Video Shows “Trim-Off” Challenge between WFT and Hornady Trimmer
You should definitely watch the five-minute video below. Mark trims five cases with the WFT, and then five more with the Hornady tool. He times the operation of each device and then measures the trimmed cases. The total variation (in length) of the WFT-trimmed cases was .001. With the Hornady tool, there was a much larger spread: .007″ (seven thousandths). Mark cautioned: “Normally the Hornady tool does a bit better than this — the variance won’t be so large. But getting better results (with the Hornady) might require trimming, measuring, then trimming again. In the video I was trying to move pretty quickly and the measurements were all taken after the initial trim. Possibly, if I slowed down when using the Hornady trimmer, the OAL measurements would have been more consistent. But that just further reinforces the point that the WFT is faster.”

NOTE: If you have a fast connection, we suggest you select 720p (HiRez) and expand to full screen.

In the video below, WFT creator Dale Hegstrom demos his device and shows how quickly it can trim a large quantity of brass. Note how the WFT is attached to a common rechargeable power drill.

“World’s Finest Trimmer” Costs $69.95
The Little Crow Gunworks “World’s Finest Trimmer is available for $69.95 from various vendors including Creedmoor Sports. WFTs index off the shoulder, not the base. The case fits tightly into a steel bearing which has been machined to a specific caliber. This decouples the stationary case from the spinning cutting blade and body, giving you a smooth, exact cut each time. While the WFT makes a nice, square cut, we do recommend chamfering inside and outside after the brass is trimmed to length.

*Most WFTs are cartridge specific. Available sizes include: .204 Ruger, .223 Rem, 22-250, 6mmBR, 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor, 6.5-284 (and 6mm-284), 6.8 SPC, 270 WSM, 7mm Rem Mag (and 300 Win Mag), .308 Win, 300 WSM, .338 Lapua Magnum. There is a ‘5 in 1′ WFT unit that will handle .17 Rem, .221 Fireball, .222, .223 Rem, and .222 Mag. The 6mmRem unit also works with .257 Roberts and 7×57 Mauser. The .30-06 WFT will trim .270 Win, .280 Rem, and .25-06 as well. And the WFT for Ultramags works with 7mm, 300, and .338 Ultramags.
Permalink Bullets, Brass, Ammo, Gear Review, New Product 9 Comments »