Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









October 18th, 2023

Worthwhile Wildcat — the 6mm-223 for XTC Competition

6mm 223 sinclair

Intro: Ron Dague wanted a new gun that was similar to his trusty .223 Rem rifle, but which fired 6mm bullets. There is a superb choice of bullets in this caliber, and Ron found that the 95gr Berger VLD could be driven to a healthy 2604 FPS by the small .223 Rem case. This 6mm wildcat based on the common .223 Remington offers excellent accuracy and very low recoil — something very important in the cross-the-course discipline. In addition, Ron’s 95gr load with Alliant Reloder 15 delivered an ES of just 4 fps over ten shots. That exceptionally low ES helps achieve minimal vertical dispersion at 600 yards.

6mm 223 Across the course McMilland stock Ron Dague Sinclair InternationalBy Ron Dague, Sinclair Reloading Tech
From Sinclair’s GunTech Articles Archive

I have watched a change in thinking for NRA High Power across the course in match rifles and calibers. There are several [popular chamberings]: 6mm AR, 6.5 Grendel, 6XC, and 6.5 Creedmoor. I have seen these rifles perform and all have done very well.

When I started this project I was looking for a cartridge that shoots and feeds well from a magazine[.] I had shot the .223 Rem in my 722 Remington and knew it had fed well so I chose the .223 Remington necked up to 6mm.

The 6mm-223 gives me what I have in the standard .223 only with a better selection of bullets. I wanted a better 600-yard bullet with a higher BC than provided by the 80 and 82 grain bullets. I also wanted a 600-yard line bullet with a .500 or better B.C. for those shots that should be 10 ring or better but seem to find the 9 ring no matter how well I held and broke the shot.

6mm 223 sinclairPutting the 6mm-233 Project Together
My project started with ordering a 6mm barrel from Bartlein with a 1-8″ twist. I called Pacific Tool and ordered the 6mm-223 reamer. I found a used Remington 700 action at a local gun shop and already had a Remington 40X stock. I then started putting the gun together.

I already had a .223 Remington match rifle, and I wanted the 6mm-223 to be as close to the same as I could make it. I installed the barreled action in a wood 40X stock to work up load data and work out any magazine feeding issues. While I was working on that, I looked for a McMillan Baker Special stock and finally found one to finish this project. I bedded the action and stock, then took the rifle to the range to check zeros on the sights and scope. I was surprised that I didn’t have to change anything on the sights. I thought changing the stock would cause sight changes. The thought went through my head, “Maybe the 40X stock isn’t all that bad”.

Here’s line-up of 6mm bullets. The Berger 95gr VLD is in the middle.
berger 6mm bullet hornady sierra line up 6mm 233

I took the new rifle to the first match of the year, a National Match Course match, and my off-hand score was 83, rapid sitting 95, rapid prone 95, and slow fire prone 197 — for total aggregate 470. This may not be my best work, but on match day the wind was blowing about 15 mph and the temp was around 40° F, with rain threatening. This was a reduced course of fire — we shot at 200 and 300 yards on reduced targets.

I used 70gr Berger bullets for this match, loaded in Remington brass with 25 grains of VihtaVuori N540 and Federal 205M primers. When I worked up loads for this rifle, N540 gave the best accuracy with the best extreme spread — 2,950 fps with an extreme spread of 20 fps on a 10-shot string. The load for 600 yards was with a 95gr Berger VLD bullet, with 23.0 grains of Reloder 15, Lapua cases, and the same Federal 205M primers. This load is 2,604 fps, with an extreme spread of 4 fps over a 10-shot string. I’ve shot this load at several 3×600 yard matches, and the accuracy has proven to be very good. At the last 3×600 match, my scores were as follows: 199-10x and 198-11X with scope, and 193-10X with iron sights. Best 600-yard score so far with iron sights was 198-12X.

6mm-223 Rem Rifle Specifications: 700 BDL action and floor plate, Bartlein 6mm 1:8″ twist, McMillan Baker Special stock in Desert Camo, Centra front and rear sights, Ken Farrell bases with stripper clip guide, Sinclair hand stop, and Jewell trigger. Gunsmith Neil Keller helped me with the metal work and instructed me on the action work and rebarreling.

Permalink Bullets, Brass, Ammo, Competition, Reloading No Comments »
August 21st, 2022

Sunday Gunday: F-Open Rifle with McMillan Kestros ZR Stock

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

Kestros ZR Stock — Impressive Design for Competition

Review by F-Class John
Walk the line at just about any rifle competition and you’ll see your share of McMillan stocks. Known for crafting high-quality fiberglass/composite stocks, McMillan has long been at top choice for competitive shooters, hunters, and tactical marksmen. Now McMillan is out to dominate F-Open with the Kestros ZR stock. The Kestros line features several models, but the ZR represents the pinnacle of craftmanship. Each one is finished off by a single craftsman and takes roughly four times longer to create than any other Kestros. So when McMillan offered me a chance to test one out, I jumped at the opportunity.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

The aluminum Z-Rail extends nicely from the front of the stock and has a nice contrast of metal against the matte finish of the stock. I inspected the rails and noticed that they are very cleanly machined — all the corners and rails were precise and sharp. As a result, I grabbed some 1000-grit sandpaper and just lightly knocked the edges and corners down just to keep from accidentally scratching myself or my gear.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

Lead time for a ZR is currently 6-9 months. I was like a kid on Christmas when mine arrived after seven months. Holding a Kestros ZR is definitely a unique experience compared to a traditional wood stock and you can’t help but feel like you’re holding something special. I chose three shades of blue that transitioned dark from the butt stock to lighter on the fore-end in a spectacular flame pattern. With McMillan, there are thousands of possible color and pattern combinations. These color/pattern options are outlined on McMillan’s Gallery Page.

The Kestros ZR comes fully inletted with pillars. I was able to bolt my Defiance action right into the stock “as is” without a bedding job. (McMillan states bedding is not required, though this is certainly something most Kestros owners will do). I threw in my action, fit a couple action screws and tightened it all down. I was amazed at how nicely it all fit together with even the little details like the port cutout being perfectly smooth with my action port. I loaded up some .284 Win rounds and headed to the range to test the new stock at 100 yards.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class
Here are examples of targets shot with the Kestros ZR at 100 yards.

During initial range testing (see above) I shot nine groups for vertical and all of them were under 0.40″ with the smallest being .08″ of vertical. I topped off the testing by shooting a 200-11X the next week at my club match. The thing that really stood out was how smoothly the stock tracked with its lower center of gravity while shooting free recoil and ultimately this translated to success on target.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class
Low-Rider — You may find that because of how low the Kestros rides as well as its additional length due to the Z rail, you may require an extension for your front rest.

CONCLUSION — Great Modern Low-Profile F-Class Stock
Overall the Kestros ZR exceeded my expectations. After a small learning curve, it was a joy to shoot and it performed great. As someone who believes in the power of muscle memory, I found each time I transitioned between the Kestros and my traditional wood stocks there was a slight adjustment period but not enough to impair accuracy in any way. Something to consider is that because every Kestros is made to the same dimensions, it makes owning multiples an easy process of switching between guns without any need for readjustment.

For those willing to put in the practice, your patience will be rewarded, and I think most shooters will find the Kestros ZR could become their new favorite stock. If you’re in the market for a new F-Open stock, the Kestros ZR is definitely one to consider.

McMillan Kestros — Proven National Championship Winning Stock

F-Class Open F-Open Norm Norman Harrold Champion Championship 2018 Raton NM New Mexico 284 Shehane Berger Bullets

Norm Harrold (above) won the 2018 USA F-Open National Championship shooting a .284 Shehane. Norm’s F-Open rig features a McMillan Kestros ZR stock and Bartlein barrel chambered for the .284 Shehane, which has a bit more case capacity than a standard .284 Winchester. Norm loaded Berger 184gr 7mm bullets in Lapua brass. Norm revealed his load in an Erik Cortina YouTube Video.

 alt=

Tips for Ordering a Kestros ZR
Ordering the Kestros ZR is a simple process thanks to McMillan’s online order form. While there are a number of options available, McMillan has a helpful guide that walks you through each one to ensure you get exactly what you need. F-Class John notes: “While filling out my form I realized that because I have a custom-designed action, I needed some help, so I gave McMillan a call. The staffers were incredibly helpful and their knowledge of all the major actions out there made answering my questions a snap. I liked the fact that there is no set, fixed price on any of the stocks. The pricing system allows customers to get just what they want (within limits) and not have to pay for anything they do not want or need.”

Permalink - Articles, - Videos, Gear Review, Gunsmithing No Comments »
November 29th, 2021

A Worthwhile Wildcat — the 6mm-223 for XTC Competition

6mm 223 sinclair

Intro: Ron Dague wanted a new gun that was similar to his trusty .223 Rem rifle, but which fired 6mm bullets. There is a superb choice of bullets in this caliber, and Ron found that the 95gr Berger VLD could be driven to a healthy 2604 FPS by the small .223 Rem case. This 6mm wildcat based on the common .223 Remington offers excellent accuracy and very low recoil — something very important in the cross-the-course discipline. In addition, Ron’s 95gr load with Alliant Reloder 15 delivered an ES of just 4 fps over ten shots. That exceptionally low ES helps achieve minimal vertical dispersion at 600 yards.

6mm 223 Across the course McMilland stock Ron Dague Sinclair InternationalBy Ron Dague, Sinclair Reloading Tech
From Sinclair’s GunTech Articles Archive

I have watched a change in thinking for NRA High Power across the course in match rifles and calibers. There are several [popular chamberings]: 6mm AR, 6.5 Grendel, 6XC, and 6.5 Creedmoor. I have seen these rifles perform and all have done very well.

When I started this project I was looking for a cartridge that shoots and feeds well from a magazine[.] I had shot the .223 Rem in my 722 Remington and knew it had fed well so I chose the .223 Remington necked up to 6mm.

The 6mm-223 gives me what I have in the standard .223 only with a better selection of bullets. I wanted a better 600-yard bullet with a higher BC than provided by the 80 and 82 grain bullets. I also wanted a 600-yard line bullet with a .500 or better B.C. for those shots that should be 10 ring or better but seem to find the 9 ring no matter how well I held and broke the shot.

6mm 223 sinclairPutting the 6mm-233 Project Together
My project started with ordering a 6mm barrel from Bartlein with a 1-8″ twist. I called Pacific Tool and ordered the 6mm-223 reamer. I found a used Remington 700 action at a local gun shop and already had a Remington 40X stock. I then started putting the gun together.

I already had a .223 Remington match rifle, and I wanted the 6mm-223 to be as close to the same as I could make it. I installed the barreled action in a wood 40X stock to work up load data and work out any magazine feeding issues. While I was working on that, I looked for a McMillan Baker Special stock and finally found one to finish this project. I bedded the action and stock, then took the rifle to the range to check zeros on the sights and scope. I was surprised that I didn’t have to change anything on the sights. I thought changing the stock would cause sight changes. The thought went through my head, “Maybe the 40X stock isn’t all that bad”.

Here’s line-up of 6mm bullets. The Berger 95gr VLD is in the middle.
berger 6mm bullet hornady sierra line up 6mm 233

I took the new rifle to the first match of the year, a National Match Course match, and my off-hand score was 83, rapid sitting 95, rapid prone 95, and slow fire prone 197 — for total aggregate 470. This may not be my best work, but on match day the wind was blowing about 15 mph and the temp was around 40° F, with rain threatening. This was a reduced course of fire — we shot at 200 and 300 yards on reduced targets.

I used 70gr Berger bullets for this match, loaded in Remington brass with 25 grains of VihtaVuori N540 and Federal 205M primers. When I worked up loads for this rifle, N540 gave the best accuracy with the best extreme spread — 2,950 fps with an extreme spread of 20 fps on a 10-shot string. The load for 600 yards was with a 95gr Berger VLD bullet, with 23.0 grains of Reloder 15, Lapua cases, and the same Federal 205M primers. This load is 2,604 fps, with an extreme spread of 4 fps over a 10-shot string. I’ve shot this load at several 3×600 yard matches, and the accuracy has proven to be very good. At the last 3×600 match, my scores were as follows: 199-10x and 198-11X with scope, and 193-10X with iron sights. Best 600-yard score so far with iron sights was 198-12X.

6mm-223 Rem Rifle Specifications: 700 BDL action and floor plate, Bartlein 6mm 1:8″ twist, McMillan Baker Special stock in Desert Camo, Centra front and rear sights, Ken Farrell bases with stripper clip guide, Sinclair hand stop, and Jewell trigger. Gunsmith Neil Keller helped me with the metal work and instructed me on the action work and rebarreling.

Permalink Bullets, Brass, Ammo, Competition, Reloading 4 Comments »
March 4th, 2020

McMillan Kestros ZR Rifle Stock Review

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

Kestros ZR Stock — Impressive Design for Competition

Review by F-Class John
Walk the line at just about any rifle competition and you’ll see your share of McMillan stocks. Known for crafting high-quality fiberglass/composite stocks, McMillan has long been at top choice for competitive shooters, hunters, and tactical marksmen. Now McMillan is out to dominate F-Open with the Kestros ZR stock. The Kestros line features several models, but the ZR represents the pinnacle of craftmanship. Each one is finished off by a single craftsman and takes roughly four times longer to create than any other Kestros. So when McMillan offered me a chance to test one out, I jumped at the opportunity.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

The aluminum Z-Rail extends nicely from the front of the stock and has a nice contrast of metal against the matte finish of the stock. I inspected the rails and noticed that they are very cleanly machined — all the corners and rails were precise and sharp. As a result, I grabbed some 1000-grit sandpaper and just lightly knocked the edges and corners down just to keep from accidentally scratching myself or my gear.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class

Lead time for a ZR is currently 6-9 months. I was like a kid on Christmas when mine arrived after seven months. Holding a Kestros ZR is definitely a unique experience compared to a traditional wood stock and you can’t help but feel like you’re holding something special. I chose three shades of blue that transitioned dark from the butt stock to lighter on the fore-end in a spectacular flame pattern. With McMillan, there are thousands of possible color and pattern combinations. These color/pattern options are outlined on McMillan’s Gallery Page.

The Kestros ZR comes fully inletted with pillars. I was able to bolt my Defiance action right into the stock “as is” without a bedding job. (McMillan states bedding is not required, though this is certainly something most Kestros owners will do). I threw in my action, fit a couple action screws and tightened it all down. I was amazed at how nicely it all fit together with even the little details like the port cutout being perfectly smooth with my action port. I loaded up some .284 Win rounds and headed to the range to test the new stock at 100 yards.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class
Here are examples of targets shot with the Kestros ZR at 100 yards.

During initial range testing (see above) I shot nine groups for vertical and all of them were under 0.40″ with the smallest being .08″ of vertical. I topped off the testing by shooting a 200-11X the next week at my club match. The thing that really stood out was how smoothly the stock tracked with its lower center of gravity while shooting free recoil and ultimately this translated to success on target.

F-Class John AccurateShooter McMillan Kestros ZR gunstock stock review test F-Class
Low-Rider — You may find that because of how low the Kestros rides as well as its additional length due to the Z rail, you may require an extension for your front rest.

CONCLUSION — Great Modern Low-Profile F-Class Stock
Overall the Kestros ZR exceeded my expectations. After a small learning curve, it was a joy to shoot and it performed great. As someone who believes in the power of muscle memory, I found each time I transitioned between the Kestros and my traditional wood stocks there was a slight adjustment period but not enough to impair accuracy in any way. Something to consider is that because every Kestros is made to the same dimensions, it makes owning multiples an easy process of switching between guns without any need for readjustment.

For those willing to put in the practice, your patience will be rewarded, and I think most shooters will find the Kestros ZR could become their new favorite stock. If you’re in the market for a new F-Open stock, the Kestros ZR is definitely one to consider.

Tips for Ordering a Kestros ZR
Ordering the Kestros ZR is a simple process thanks to McMillan’s online order form. While there are a number of options available, McMillan has a helpful guide that walks you through each one to ensure you get exactly what you need. While filling out my form I realized that because I have a custom-designed action, I needed some help, so I gave McMillan a call. The staffers were incredibly helpful and their knowledge of all the major actions out there made answering my questions a snap. I liked the fact that there is no set, fixed price on any of the stocks. The pricing system allows customers to get just what they want (within limits) and not have to pay for anything they do not want or need.

Permalink - Articles, Gear Review, Gunsmithing, New Product, Tech Tip No Comments »
October 6th, 2019

Sunday GunDay: Chris Nichols’s 600-Yard Light and Heavy Guns

IBS Benchrest Chris Nichols Heavy Gun Record HG aggregate north carolina
Chris Nichols with potential world record (1.297″ 4-Target Agg) Heavy Gun Targets!

Report by Bart Sauter, Bart’s Custom Bullets
Chris Nichols is one of the best 600-yard shooters in the game. This 2019 season he compiled one of the most impressive mid-range benchrest seasons ever. Check out the stats — Chris’s nine-match, Two-Gun Group Aggregate (Agg) for the year is 1.983″! That’s under two inches average at 600 for 72 record targets fired in competition. Many 600-yard shooters aspire to shoot a single, 4-target Agg that measures 1.983″, but doing that for 72 targets is amazing!

And of the nine matches Chris shot, he took SIX Overall Two-Gun wins — a 67% win ratio. And in the process Chris also shot what is possibly the smallest 4-target Heavy Gun Agg ever recorded — 1.297 inches. Hey readers — that Agg works out to 0.206 MOA average group size — well under quarter-MOA for four, 5-shot groups at 0.34 MILES (600 yards)!

IBS Benchrest Chris Nichols Heavy Gun Record HG aggregate north carolina
Chris with 0.665″ group at 600 yards. This is the smallest HG group fired in the IBS in 2019.

The Equipment: 6mm Dasher Light Gun and Heavy Gun
Chris likes to run 1.550 stainless steel Bat “B” actions, Jewell triggers, Brux or Bartlein barrels. He prefers wooden stocks as he feels they produce a better resonance for Long Range rifles. Chris has his own stock design crafted by Johnny Byers. Imagine a Wheeler LRB stock front half mated with an McMillan ST 1000 rear section and you have Chris’ stock! It features a Wheeler-type, 4″-wide fore-end with an ST 1000 low-comb profile in the back. Both Light Gun and Heavy Gun sport Vortex 15-60x52mm Golden Eagle scopes mounted with Harrell’s double screw tall rings. Chris does NOT use either muzzle brake or tuner.

IBS Benchrest Chris Nichols Heavy Gun Record HG aggregate north carolina
Here is Chris at his home range with his Light Gun (17 lbs. max).

Chris Nichols’s Heavy Gun is a true heavy coming in at around 42 pounds. It was responsible for the HG Agg of 1.297″ (potential new world record). His season-long aggregate with his Heavy Gun was 1.861″ for 36 targets! This rifle has similar components as his Light Gun, except the barreled action rides in a barrel block in a McMillan HBR 50 BMG stock.

IBS Benchrest Chris Nichols Heavy Gun Record HG aggregate north carolina

Both rifles ride a top of a Sinclair competition rest with a Protector DR Flat Top rear bag. When Chris goes to HG gun he simply switches tops (made by Daniel Greenlaw) on his front rest to accommodate the larger forend. As Chris says ,” This keeps things simple and exactly the same. ” Just the way he likes it.

Reloading for the 6mm Dasher
Chris’s load choice for both LG and HG is Hodgdon Varget pushing 105gr Berger VLDs. He uses CCI 450 primers, seated with an old Lee hand primer. When it comes to reloading, Chris likes to keep things as simple as possible. “If people saw me reloading they’d probably laugh!” Chris revealed that he doesn’t anneal or clean his cases. He just sprays them down with Hornady One Shot Case Lube, resizes, then runs a brush down the necks, and cleans the primer pockets. The only cleaning his cases get is when he wipes the lube off of them. Chris WILL trim and chamfer as needed.

Chris says seating consistency is critical — he uses a K&M Arbor press with force dial indicator. I asked if there were certain numbers he looks for when seating. Chris replied, “I’m only concerned with consistency and not a certain number, 5 pounds or 60 pounds. It doesn’t matter as long as they are the same. I take what the brass gives me.”

Tuning the 6mm Dasher for Record-Setting Accuracy
I asked Chris what was special about his Dasher and how he kept it tuned and so competitive? His reply is something all shooters should pay careful attention to: “[Success] starts with having a good reamer, bullets and barrels. But more than that, it’s KNOWING your Cartridge, KNOWING your bullets, and KNOWING your barrels! I’ve shot it so much I just know what to do. I’m comfortable with it. I know how to get it to shoot and when it’s not, I have a pretty good idea how to get it back in tune. Once you know your equipment, then you can learn how to get the most out of it.”

IBS Benchrest Chris Nichols Heavy Gun Record HG aggregate north carolina

Chris has a range at his house and he tunes at 300 yards. He looks for consistent, 300-yard 5-shot groups of 0.600″ or less! He wants to see nice round groups! Not groups with four in and one out or vertical strings. Chris starts by finding “touch” (to the lands) then he moves the bullets .002″ off the lands and begins tuning. Chris has found that usually somewhere around .008-.012″ off the lands is where his Berger 105gr VLDs shot best. I asked Chris what’s the biggest factor contributing to his success? He said, one big thing was that he can do his own work. That’s a huge advantage.

Look for Accuracy First, Velocity Second
Early on Chris had it in his mind that for a 6mm Dasher to shoot best he needed to achieve a certain velocity range — 2990 to 3030 FPS. The problem was he wasn’t paying attention to what the target was telling him. He’d get to the speed he was looking for but the accuracy wasn’t there. Once he started slowing the speeds down and giving the barrel what it wanted, then the accuracy came! Also with the slower speeds came better consistency.

Chris Nichols’s Tuning Tips for 6mm Dasher:

• Take consistency over speed.
• Only change one thing at a time and run it to the ground.
• Every barrel is a little different, so give it what it wants.
• Pay attention to what your target is telling you.
• Don’t be afraid to REDUCE your powder load.

Chris Nichols’s Advice for New Shooters
Chris says the best thing a new shooter can do is align themselves with knowledgeable people, and if they will talk, listen! Next, be ready to buy the best equipment or be ready to buy it twice. Chris also says: “Don’t cheap-out on sighters. Sighters need to be just as good as your record rounds.”

In the Beginning — Learning the 600-yard Benchrest Game
Chris’s shooting career began in 2012. His first win came in 2014. He was shooting beside guys like Sam Hall, Larry Isenhour, Mike Hanes, Jeff Godfrey James Coffey, and Chad Jenkins, who are very tough competition indeed. He said when he won he was ecstatic and he’ll never forget it! That first trophy had him feeling like he’d just won the Nationals! Chris shot a 6BR for the first two years of his career, before switching to the 6 Dasher. I asked him why he switched? He said, “guys were starting to shoot the Dasher and winning with it!”

I asked Chris if he had a mentor and he said, “not really”. He learned by watching the guys who consistently finished Top 5 at matches and occasionally asked them a question. Not two questions, just one! Chris didn’t want to push his luck by asking too much. Then Chris would take that information and test it and apply it to his own shooting. Chris says, “he learned mainly by the ‘school of hard-knocks’. The good thing about learning that way is it sticks with you!”

Chris Nichols 2019 600-Yard Win List and Statistics

(more…)

Permalink - Articles, Bullets, Brass, Ammo, Competition, Gear Review, Gunsmithing No Comments »
August 18th, 2019

Sunday GunDay: New 33XC Rifle for Reigning King of 2 Miles

ELR light class Paul Phillips Global Precision

ELR light class Paul Phillips Global PrecisionNew Cartridge, New Rifle for the King
Paul Phillips is the reigning King of 2 Miles. The founder of the Global Precision Group, Paul is one of the top ELR marksmen on the planet. He has also been a team-mate of past K02M winners.

Paul recently put together a new rifle for the 25-lb max, .338 caliber-or-under ELR Class. This is chambered for the 33XC, an efficient new cartridge devised by 11-time National HP Champion David Tubb. With promising initial testing at 500 yards, it looks like Paul’s 33XC project will be a success. The rifle’s first match will be the NRA Extreme Long Range Championship, to be held August 21-23, 2019 at Camp Atterbury, Indiana.

ELR light class Paul Phillips Global Precision

ELR light class Paul Phillips Global Precision

Paul reports: “The 33XC is ready for the NRA ELR Nationals. I have tested loads from 3100-3450 FPS and and will settle on a load around 3250 FPS [which is] my most accurate load so far. The Peterson Cartridge brass is really working well.”

Paul states he would like to look for a higher node from 3300-3400 GPS: “Next stop is with the Applied Ballistics LLC mobile labratory and radar testing with a PDM for the Nationals.” Paul cautions: “I encourage everyone to start low and work up. Every chamber, barrel, and components are a little different.”

ELR light class Paul Phillips Global Precision

During initial testing, Paul’s 33XC put three shots in 0.27″ at 100. Then, at 500 yards, the rifle produced a 3-shot group around 1/3-MOA with just 1.22 inches of vertical. That’s pretty impressive for early testing. Paul will also be trying some Berger bullets soon. When he determines the most accurate load, Phillips will stretch the rifle’s legs, shooting out to 2500 yards and beyond.

Quote: “The Cutting Edge Bullets are not the highest BC but they are very stable and consistent at ELR (sub-sonic) ranges and that’s the most important factor in finding the best ELR bullet. I actually test all my bullets at sub-sonic speeds to make sure they are consistent and stable. Finding a good load at 500 yards is just the first part. The real test is shooting them at sub-sonic speeds and see how consistently they group. This is what gives you the highest percentage to impact at 2 miles and beyond.”

ELR light class Paul Phillips Global Precision
CLICK Image for full-screen version.

This rifle features a BAT action mated to a 34″ Bartlein barrel chambered for David Tubb’s new 33XC cartridge. Paul Phillips is currently running Cutting Edge 275gr Lazer solid bullets. Paul notes: “I also have a .338 Lapua Magnum barrel and 300gr Berger bullets for the restricted class in France.” Paul gave special thanks to Alex Wheeler for doing the metal work and Alex Sitman for doing the bedding.

Rifle Component List
Action: BAT Machine CTH dual-port action
Trigger: Bullet Central Bix’N Andy
Barrel: Bartlein 1:8″-twist barrel (34″)
Chambering: 33XC for Peterson brass
Stock: McMillan A6 Super Mag, Bedding Alex Sitman
Scope: Nightforce Optics 7-35x56mm F1 ATACR.
Bipod: Duplin Rifles

33XC Load Components
Cartridge Brass: 33XC by Peterson Cartridge
Bullets: Cutting Edge 275gr Lazer Bullets
Powder: Vihtavuori

ELR light class Paul Phillips Global Precision

Paul Phillips notes: “Alex Sitman has been bedding rifles stocks for most of his life. I believe that [bedding] is a very important … to keep consistent accuracy and repeatable zeros after traveling all over the globe.”

ELR light class Paul Phillips Global Precision

Even with the TacomHQ Charlie Tarac scope prism in place, the rifle makes the 25-pound weight limit with Duplin Rifles bipod. Paul says: “I love it when a plan comes together!! I’m under by 2 ounces!”

About the 33XC (eXtra Capacity) Cartridge
David Tubb invented the 33XC cartridge because he thought the CheyTac cases were too much trouble — requiring a larger action, oversize presses, and ultra-expensive dies. The 33XC was designed to fit .338 Lapua Magnum-size actions and use normal reloading presses.

The 33XC (eXtra Capacity) has 137.5 grains of H2O capacity with over 125 grains of usable powder capacity while leaving the 0.393″ neck unfilled for bullet seating.

The 33XC has a .338 Lapua Magnum lineage. Think of it as a better, 35°-shoulder .338 LM. David explains: “The 33XC uses standard reloading dies along with a 7/8″ x 14 TPI reloading press. There is no fire-forming — all case ‘improving’ has already been done with a production case that has 20 grains more powder capacity, 35-degree shoulder, and longer neck compared to a .338 Lapua Magnum. This puts the various .338 Lapua wildcats and the Rem Ultra Mag Improved into the ‘also ran’ category. They simply can’t compete with the velocities attainable with the 33XC.”

ELR light class Paul Phillips Global Precision

The 33XC is based off of a .580″ bolt head. Tubb states that “A fired case will extract with little effort when using a properly-polished chamber with a maximum powder charge after resizing with the Superior Shooting Systems FL sizing die.” Tubb’s 33XC die reaches the case head which is important for accuracy. Peterson Cartridge produces the 33XC brass for Superior Shooting Systems. This high-quality brass costs $115 for 50 cases (or $2.30 per case), and can be purchased directly from Superior Shooting Systems.

ELR light class Paul Phillips Global Precision

Permalink Bullets, Brass, Ammo, Competition, Gunsmithing, New Product 1 Comment »
May 8th, 2019

Shilen Barrels, Actions, and Rifles from the Heart of Texas

Shilen Actions Complete rifles barrel nut Savage Remage

Did you know that Shilen Rifles Inc. (Ennis, TX) offers barreled actions and complete rifles? And that Shilen offers a Savage-style, barrel-nut system for its Rem-clone actions? After several years of development, Shilen now offers custom actions ($950.00), barreled custom actions ($1500.00), and complete rifles ($3200.00 and up).

Shilen Actions Complete rifles

The new Shilen custom actions are CNC-milled from high-grade stainless steel. Two types are offered — the multi-shot DGR (Repeater) or the single-shot DGV (Varminter) action. Both actions will be offered in most common bolt faces and both right-hand and left-hand actions are immediately available. The DGR and DGV actions have a 1.350″ diameter with 8-40 scope base mounting screw holes, and an 0.300″ pinned recoil lug. The spiral-fluted bolts feature a floating bolt head with an interchangeable bolt handle knob. These actions feature a footprint similar to the Remington Model 700. Both DGR and DGV actions will accept many aftermarket components crafted for Rem-700 style actions, including triggers and bottom metal.

Barreled Actions with Barrel-Nut System for Easy Barrel Exchanges
Along with the stand-alone DGR and DGV actions, Shilen is offering barreled action assemblies, chambered and ready to drop into Rem 700-inletted stocks. The actions are fitted with Shilen match-grade barrels. The barrels feature a 1-1/16″x20 barrel thread and are attached to the action by a barrel nut. This Savage-style barrel nut system simplifies headspacing, allowing easy swapping from one barrel to another. With the simple barrel-exchange procedure, you can shoot multiple chamberings with a single action/rifle. For example, shooters can change from a .223 Remington to a .204 Ruger or a .22-250 to a 6mm BR in a matter of minutes.

Complete Rifles with McMillan Stocks
With Shilen’s complete rifles, buyers can choose their chambering, and select barrel and stock configuration. Shooters can choose between a sporter weight wood stock or a variety of McMillan fiberglass stocks. With all complete rifles, the entire package is delivered in a quality gun case and Shilen even includes table mat, cleaning rod, bore guide, jag, bore brush, and cleaning patches. For more info, call (972) 875-5318 or email comments@shilen.com.

Shilen Actions Complete rifles

Permalink Gear Review, Gunsmithing No Comments »
January 22nd, 2018

First ELR Central Long Range Record Match in Nevada

ELR Long Range Record Match Pahrump Nevada Front Sight

On 1/21/18, new World Records were set under ELR Central rules for verified, consecutive three-shot string without sighters. Competitors started from cold bore, no sighters or ranging shots allowed. That’s a tough standard. In fact the first 12 shooters failed to put three shots on target at 1500 yards before Paul Phillips took his turn. Paul, Lucky number 13, placed all three of his shots on the 36″ x 36″ plate, claiming a first-ever record. Later that afternoon, John Armstrong duplicated that feat, also putting three shots on target at 1500 with no sighters.

Nate .375 CheyTac Tubb Rifle Stallter ELR record

But the best performances of all came later. Nate Stallter, shooting a .375 CheyTac, nailed his three shots at over one mile — 1768 yards. But it gets better — Nate broke his own record later in the afternoon, going 3 for 3 at 2011 yards.

David Tubb posted: “Congratulations to my son-in-law, Nate. Today he won the ELR Central World Record competition. This competition allows two separate attempts (spaced four hours apart) and consists of three cold bore shots each time. He took 3 shots and had 3 hits at 1768 yards in the morning and then beat his own record in the afternoon with 3 shots and 3 hits at 2011 yards after the wind had become trickier.”

Stallter used the new Tubb Adaptive Target Rifle (Tubb Gun) with a Dynamic Targeting Reticle and Tubb T7T two-stage trigger. He was shooting the .375 Cheytac with a 364gr Warner flatline bullet that has a patent pending Nose Ring modification in a Schneider 1:7″ twist barrel. Three of the Tubb Rifles are shown below. Note the long barrels.

ELR World Record Nate Statler 2011 yards 1768 yards one mile Tubb Gun Warner Bullet .375 CheyTac

As we explained, this was a tough challenge. Competitors started with a cold bore, with no sighters alowed — that makes it especially tough.

Watch this video to hear the record-setting shooters describe their equipment — chambering, action, stock, barrel, bipod, and optics. No the video is not sideways! Nearly all this video is correct, horizontal orientation. Click triangle to start correct format.

None of the competitors had shot these kind of distances at this facility, the Front Sight Firearms Training Center in Pahrump, Nevada. And the “no sighters” rule really added to the difficulty — witness the fact that the first 12 shooters failed to put three consecutive hits on a square yard of steel at 1500. Here are the three record-setting shooters:

1. Paul Phillips, 1500 yards (first record) | 2. John Armstrong, 1500 yards (tied record)

3. Nate Stallter, 1768 yards (new record) | 4. Nate Stallter, 2011 Yards (World Record)

Those who understand the challenge were impressed …

Andy McNeill observed: “I’ve shot targets further too, but I didn’t go 3 for 3 with no sighters. These hit cold bore and then two consecutive follow-up shots at specific target sizes. This is what a record should be. Not I hit a target at X distance once after slinging lead at it all day.”

Jacob Scobell liked the match format: “Love that this is intentional, consecutive impacts with a fixed size target and not just a statistical probability of hitting the broad side of a barn with unlimited shots. Excellent to see a standard being set.

Now will all of these other supposed ‘world record holders’ step up and enter this competition? Sure some guy who can impact upon demand beyond 4000 yards would cake walk this right? A registered event with multiple shooters means put up or shut up.”

Permalink Competition, News 12 Comments »
December 10th, 2016

Beast in the Works — New ELR Stock from McMillan

Kelly McMillan ELR fiberglass stock gunstock KO2M 50 BMG Cheytac
Kelly McMillan with his lastest creation — the “ELR Beast”.

The design team at McMillan Fiberglass Stocks is working on a new heavy-duty stock for the Extreme Long Range (ELR) game. This beefy gunstock is designed to handle the heavy torque and recoil of big-caliber cartridges such as the .408 Cheytac and .50 BMG. The stock is also designed to balance the ultra-long barrels favored by ELR shooters and King of 2 Mile competitors. Shown above is the boss-man himself, Kelly McMillan, with the new ELR stock prototype. Kelly calls this “the ELR Beast”. Note how the cheekpiece is slotted to allow unimpeded movement of the extra-long bolt.

Kelly McMillan ELR fiberglass stock gunstock KO2M 50 BMG Cheytac

Kelly tells us: “Making headway on the ELR Beast. Using Paul Phillips’s barrel and action we have been able to make some progress in both the design and the cosmetics of the stock. I am pleased with where we are at this time. As is, this set up weighs 46 pounds, I suspect we can get this stock to weigh between 8 and 9 pounds maximum, and maybe 5 pounds minimum.”

Kelly McMillan ELR fiberglass stock gunstock KO2M 50 BMG Cheytac

Permalink New Product, Tactical 4 Comments »
July 21st, 2016

New Rapid Ordering System for McMillan “Inlet Ready” Stocks

McMillan Fiberglass stocks inlet ready order free shipping retail store

With McMillan’s new “Inlet Ready” series of fiberglass stocks, you can get a customized McMillan stock in just two to four weeks. Use the web-based stock selector in McMillan’s online Retail Store.

To get to the Inlet Ready section, from the McMillan Home Page click “Retail Store“, then select “Stocks in Inventory” from the left-hand column. After clicking “Stocks in Inventory” from the left column, select “Inlet Ready” from the sub-menu. This video explains how to order your Inlet Ready stock for delivery in two to four weeks:

Get Free Shipping with Orders Over $400.00
Here’s another way you can save on purchases of McMillan stocks and shooting accessories. Go to McMillan’s online Retail Store. Choose stocks, bipods, gun cases, ammunition, apparel, triggers, and other items offered for sale. Then, during check-out, use Promo CODE mcm16. This will provide FREE Shipping if your total order is $400.00 or more.

NOTE: Free shipping applies to orders over $400, standard ground delivery in the Continental USA. Shipping charges on previous orders will not be reimbursed. This offer cannot be combined with other promotions or offers.

Product and Sale tip from EdLongrange. We welcome reader submissions.
Permalink Gunsmithing, Hot Deals No Comments »
June 26th, 2015

Amazing Air-Brush Paint Job on McMillan 50-LBR Stock

Ronnie Smith McMillan Benchrest Stock S&S Dallas Airbrush Rifle

Benchrest shooter Ronnie Smith had the folks at S&S Precision craft a barrel block benchrest gun with a McMillan 50 LBR stock. While the metal work (and block installation) is impressive, the rig’s jaw-dropping feature is an amazing paint job applied by artist David Tidwell of Dallas Airbrush. Ronnie wanted a stock that didn’t look like anything else you’ve ever seen. Working from Ronnie’s concept of a junkyard-sourced rifle, Tidwell created a masterpiece of airbrushing. The finished stock looks like it was hammered from old beat-up metal, complete with dents, grind marks, hollows, Bondo, and wire-mesh patches. Watch the video below to see how this amazing paint job was applied, from start to finish. (Definitely worth watching!)

If you have a stock you’d like painted by David Tidwell, visit DallasAirbrush.com, call 214-529-4410 or email: david [at] dallasairbrush.com. Dallas Airbrush currently sprays out of Texas Body Works, 2415 Midway Rd Suite 111, Plano, TX 75025.

Ronnie Smith McMillan Benchrest stock S&S Dallas Airbrush Rifle

Permalink - Videos, Gunsmithing No Comments »
July 20th, 2012

Sako Quad Rimfire Trainer — Buyer-Configurable Special Edition

Looking for the perfect rimfire training rifle, one that has the look, feel, and ergonomics of your favorite centerfire field/tactical rifle? Well here’s a unique opportunity. EuroOptic.com is putting together a special limited edition run of 49 Sako Quad rifles, configured exactly as the buyer specifies, with McMillan Stocks, Lilja Barrels, and Cerakoted Metal. There will only be 49 such rifles available, and the deadline to order is July 31, 2012. EuroOptic.com has a few offerings left, but it expects all 49 Special Edition Quads will be sold by the end of this month.

The Sako Quad was a great concept — one rimfire rifle with a quiver of barrels in different rimfire chamberings. However, many potential buyers didn’t need or want all four barrels. Many potential buyers liked the idea of the Quad as a rimfire trainer, but they wanted a rifle fitted with a full-size, fiberglass stock, so the gun would have the same ergonomics and feel as their centerfire bolt-guns. That would make it the ideal rimfire training rig.

Eurooptic.com Sako Quad

Eurooptic.com Sako QuadWell, this dream is now a reality. EuroOptic.com has decided to make a special limited run of 49 custom rimfire trainer rifles with premium components.

These Special Edition Quads will feature Sako Quad actions, McMillan fiberglass stocks, Lilja custom barrels, as well as quality third-party scope rails, triggerguards, and bolt knobs. The bedding and coating work will be done by GA Precision.

49 Special Quads — With McMillan Stocks, Lilja Barrels, and Cerakoted Metal
Each rifle will be “made to order” for the 49 lucky guys who sign up before orders close. The pre-order price (including ONE barrel, no optics) is $2195.00 + $30.00 for insured shipping in a hard card. Those who pre-order the rifles will be able to select the colors and special features they prefer. Buyers can chose among six (6) different McMillan stocks (with your choice of finish). Each rifle comes with one (1) .22 LR barrel. For an additional $350.00 per barrel, you can also order extra Lilja barrels chambered for any of these rimfire cartridges: .22 WMR, .17 HMR, or 17 Mach 2.

Each rifle will have the following standard features:

  • SAKO Quad receiver engraved with EuroOptic Logo and 1 of 49, 2 of 49 etc.
  • Lilja custom drop-in bull barrel in .22 LR. Other barrels/calibers can be added.
  • McMillan stock of your choice, bedded by GA Precision.
  • Cerakote metal color of your choice: Black, Desert Tan, Mil-Spec OD.
  • Picatinny +20 MOA scope rail by DIProducts.
  • Billet Aluminum trigger-guard by DIProducts.
  • KMW bolt knob.

You can choose from a variety of popular McMillan fiberglass stock designs. These include: A2, A3, A3-5, A5, HTG (M40), and Sako Varmint. The purchaser can also select the stock color/pattern. Click here to view some stock color options.

Additional Features (Extra-cost Options)

Threaded muzzle with cap — $125 per barrel
Coating of one additional barrel — $75.00
KMW cheekpiece installed — $150.00
Sling stud — $7.50 | Flush cup — $13.00
Limbsaver butt-pad — $23.00
Adjustable LOP with Spacer System — $116.00
2-way vertical butt-plate — $116.00
3-way butt-plate — $180.00
Saddle Cheekpiece — $116.00
Integral thumbwheel cheekpiece — $142.00
Anschutz fore-end rail — $53.00
Seekins fore-end PIC rail for bipod — $33.25

Ordering Instructions

To order, call EuroOptic at (570) 220-3159 or email: alex [at] eurooptic.com . When ordering, please specify McMillan stock model and color choice, as well as any extras you would like (including additional barrels), along with your choice of metal color. NOTE: Eurooptic.com requires a 25% non-refundable deposit for these rifles. Once the deposit is taken, the stock will be ordered as specified. The Quads are to be delivered by Sako in August 2012, and all 49 rifles should be completed before the end of 2012.

Eurooptic’s special pricing will continue until all 49 rifles are sold or until JULY 31st, whichever comes first. July 31st is the last day to pre-order a rifle to your spec. If any rifles remain unsold at that point they will be sold at normal price reflected on the Eurooptic.com website.

Permalink Hot Deals, New Product No Comments »