Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









September 3rd, 2013

Springfield Armory Recalls 3.3 XD-S Pistols for Safety Reasons

Springfield Armory (Springfield) is recalling certain 3.3 XD-S™ 9mm and 3.3 XD-S™ .45ACP pistols (serial numbers below). The reason for the safety recall is that “under exceptionally rare circumstances, some 3.3 XD-S™ 9mm and .45ACP caliber pistols could experience an unintended discharge during the loading process when the slide is released, or could experience a double-fire when the trigger is pulled once.” This could cause serious injury or death. If you own an XD-S 9mm or .45 ACP pistol subject to recall, stop using the pistol, carefully unload it, and return it to Springfield. Springfield will install new components that should eliminate the potentially dangerous condition.

Springfield Armory XD-S 3.3 Safety Recall

This Safety Recall Applies to:
Springfield 3.3 XD-S™ 9mm pistols – serial numbers between XS900000 and XS938700.
Springfield 3.3 XD-S™ .45ACP pistols – serial numbers between XS500000 and XS686300.
Note: This Safety Recall does not apply to any XD® or XD(M)® pistols.

Springfield Armory XD-S 3.3 Safety Recall

If you have one of the affected XD-S 3.3 pistols, go to the Springfield Recall Notice Page (or call 800-680-6866). Click on the Get Started link at the top of the Recall Notice Page. Enter your serial number and click Next. The serial number is located on the frame beneath the dust cover (accessory rail). If your pistol is subject to recall, you will need to provide your contact info. If you no longer own the 3.3 XD-S™ 9mm or .45ACP pistol, please advise Springfield of the current owner.

Springfield will provide a return authorization and mailing label, so owners can return affected XD-S pistols at no cost. Springfield will then install upgraded components, and return the pistol. Visit www.springfieldrecall.com for further information or call 800-680-6866.

Permalink Gunsmithing, News No Comments »
September 2nd, 2013

USA Shooting 300M National Championships Held at Fort Benning

Report and Photographs by Tony Chow
On August 12th to 16th, USAMU’s Fort Benning range hosted the 2013 USA Shooting 300m National Championships. This match, held every four years, nominates athletes to represent the United States at the 300m World Championships, due to be held in 2014, in Granada, Spain.

300m Championships Fort Benning

300m Shooting — A World-Class Challenge
300m shooting is a challenging discipline. With much smaller scoring rings than NRA targets, the 300m target can bedevil even the most experienced High Power shooters, especially in tricky wind conditions. While European 300m shooters typically use expensive rifles from the likes of Gruenig & Elmiger (G&E) and Bleiker, less costly American-made equipment has proven to be every bit as competitive. Case in point are the free rifles used by the USAMU team, all of which are built from American target actions such as Panda and BAT, fitted with Krieger barrels, and glass-bedded into Anschütz stocks.

The competition took place in unseasonably mild weather for this time of the year in Georgia. As the popularity of 300m shooting is limited in the United States, 21 shooters in total took part in four days of competition. Despite the light participation, the athletes included some of the best international rifle shooters in the country. The relaxed and club-like atmosphere belied intense and high-level competition on the firing line.

chow300m04op

chow300m03op

Electronic targets record all shots as 10, 9, 8, etc., with the X-count being the first tiebreaker. Each whole number score is accompanied by a more precise score that ranges from 0-100. An official 10, for example, could be anything from 91 (on the edge of the ring), all the way to 100 (dead center). The more precise score is NOT used officially for score keeping in ISSF competition, but could be in the future, as already is the case in 50m prone and 10m air rifle.

300m Championships Fort Bennign

chow300m02op

3P Course of Fire and Results
The 3P events occupied the first two days of competition. Athletes shot in three positions–kneeling, prone, and standing — using free rifles, mostly chambered in 6BR. Under ISSF rules, men fire 40 record shots in each position, while women fire 20 record shots in each position. Each event is repeated on the second day, and the two-day aggregates determined the winner. In Men’s 300m 3P, USAMU’s Joseph Hall, who had never shot a 300m match before, beat his more experienced teammates Joseph Hein and Michael McPhail to take gold. Among women, USAMU’s Erin Lorenzen edged out 2008 World Championship veterans Reya Kempley and Janet Raab for the gold.

The prone and Standard Rifle events followed in the second half of the competition. The 300m prone match is shot by both men and women, using same free rifles as in the 3P events. The Standard Rifle match is another 3-position event, except contested only among men, using rifles strictly limited in external shape and adjustability. Cooler temperatures and intermittent rain made conditions trickier to read than during the first two days. In men’s prone, USAMU’s Eric Uptagrafft took gold, edging out Unit teammates Hall and McPhail. In women’s prone, Erin Lorenzen once again came out on top over Reya Kempley (photo below) and Michelle Bohren.

300m Fort Benning National Championship Tony Chow

chow300m08op

In the Standard Rifle event, AMU’s Joseph Hall continued his good form and took another gold over teammate Joseph Hein. Equally noteworthy is the third place finisher Steve Goff. Goff, an AMU Hall of Famer who now competes as a senior in USAS matches, beat back much younger challengers to earn the third and final slot in the 2014 US Men’s Standard Rifle Team.

Cartridge Options for 300m Shooting — by Tony Chow
The cartridge of choice in 300m is 6mmBR Norma (aka 6BR). The AMU shooters all shoot Norma Diamond Line 6BR factory ammo, loaded with moly-coated 105gr Berger HPBT bullets, with the notable exception of prone match winner Eric Uptagrafft, who shoots handloads with HBN-coated bullets in his 6mm Dasher. Civilian shooters mostly shoot the 6mmBR as well, also preferring Berger bullets. I was the odd man out shooting a Gruenig & Elmiger (G&E) chambered in 6.5×47 Lapua. That cartridge was actually the result of a collaboration between G+E and Lapua to create an alternative to 6BR, though in the 300m world, it never managed to catch on. There was one shooter using 6.5-284 and another shooting a wildcat cartridge called “.260 BMR (boomer)”.

6BR 6mmBR Tony Chow 300mI’m not the authority on the pros and cons of various calibers. I doubt that most world-class 300m shooters concern themselves too much with these matters. The 6BR is simply good enough. It holds well inside the 10-Ring, is relatively economical, and offers extremely long barrel life when using mild factory loads. G+E rates its chrome-moly, cut-rifled 6BR barrels as capable of lasting 7,000 rounds. The AMU gunsmith, Glenn Sulser, told me that the AMU’s policy is to re-barrel at the 4,500-5,000 round mark.

Longer cartridges such as 6.5×47 and 6XC are supposed to offer easier feeding, but in my observation, the nose-heavy nature of 6BR is, in practice, not a major problem for 300m shooters. One of the advantages of 6.5×47 is even longer barrel life, and that’s the reason I went for this caliber myself. But looking back now, the greater recoil and extra cost in brass and powder are probably not worth it.

Factory Ammo vs. Handloads — Cost Considerations
One of the advantages the AMU shooters enjoyed over the civilians is that the Unit marksmen had an unlimited supply of ammo, and therefore could shoot as many sighters as they wished. In a 15-minute sighting-in period, it was not uncommon for AMU shooters to fire 20+ sighter shots, just as they do in smallbore. We civilians had to settle with under 10 sighters, in order to leave enough for the match.

Unless you are filthy rich or have someone else paying for the ammo, reloading is definitely the only way to go. A reloaded round costs under 50 cents a piece. The European factory ammo costs nearly $3 a round these days (as sold in the USA).

CLICK Photos to See Full-Screen Images:

chow300m07op

chow300m09op

chow300m06op

chow300m010op

Permalink Competition, News 12 Comments »
September 2nd, 2013

NSSF Leads Fight Against Statewide Lead Bullet Ban in California

bullet ban lead california ab 711A lead-free “utopia” where bullets are banned and hunting is, for all practical purposes, eliminated — that’s apparently what some legislators want California to become. California Assembly Bill AB 711 would completely ban the use of traditional lead ammunition for hunting anywhere in the state. What’s more, many legislators acknowledge that this ban could, in the near future, be applied to all shooting sports in the Golden State. If you can’t buy bullets, you can’t shoot — and that seems to be the real agenda.

NSSF has purchased billboards in the Sacramento area to urge opposition to AB 711 and has been airing radio commercials that reveal the role of the anti-hunting groups behind this ill-conceived legislation. This week, the opposition to AB 711 was joined by a major state labor organization. NSSF urges all California hunters, target shooters and gun owners to contact their state legislators to oppose AB 711.

To understand more about the issue, read a well-reasoned editorial published in the Outdoor Wire. Even non-Californians should be concerned, because other states might follow California’s lead in the future. And AB 711 is not the only serious anti-gun measure on the table. In addition to AB 711, several other highly restrictive measures are in the works. Proposed legislation would place ALL semi-automatic rifles with detachable magazines on California’s list of banned “assault weapons”. Another bill would block Californians from purchasing long guns unless purchasers pass a state-mandated written test.

Permalink Bullets, Brass, Ammo, News No Comments »
September 1st, 2013

Nammo Plans to Acquire Vihtavuori Powder Plant in Finland

Vihtavuori powdersEurenco, current owner of the Vihtavuori Oy powder manufacturing facility in Finland, has been seeking a new owner for the facility for many months. Well it looks like there is a buyer, Nammo Group, parent company of Lapua. The acquisition is not final — “Due Diligence” must still be completed. However, if the deal goes through, this will be good news for fans of Vihtavuori rifle and pistol propellants such as the popular N133, N135, N140, N150, and N320. N133 is winningest modern powder in the short-range benchrest game and N320 is an outstanding pistol powder favored by many .45 ACP bullseye competitors. Here is the text of the notification issued Friday August 30, 2013 by the Nammo Group.

Nammo group Lapua acquires Vihtavuorio Oy powder plant in Finland

Permalink Bullets, Brass, Ammo, News 3 Comments »
September 1st, 2013

Ruger Releases New Bolt Action Rimfire Rifles

Ruger recently announced the new Ruger American Rimfire™ series of bolt-action rimfire rifles, chambered in .22LR or .22 Magnum. These rifles feature an interesting convertible polymer stock and the .22LR versions can run 10/22 magazines. You could say the new rifles borrow features from the centerfire Ruger American Rifle® series, while offering mag interchangeability with 10/22 rimfire rifle. Ruger offers both full-sized (22″ barrel/13.75″ length of pull) and compact (18″ barrel/12.5″ length of pull) models, both of which are available in either .22 LR or .22 Magnum. All models have a suggested retail price of $329.00.

ruger american rimfire 10/22 rotary magazine convertible stock

Comb Height Adjusts with Interchangeable Stock Modules
Ruger’s new rimfires feature interchangeable stock modules that provide variable comb heights. Standard models come with long length of pull modules, while compact models come with short length of pull modules. By simply removing the rear sling swivel stud, stock modules can be changed in seconds.

ruger american rimfire 10/22 rotary magazine convertible stock

.22LR Models Can Use All 10/22 Magazines
Models chambered in .22LR feature the detachable, flush-mounted 10/22® BX1 10-round rotary magazine and accept all 10/22® magazines. Models chambered in .22 Magnum use the detachable, flush-mounted JMX1 9-round rotary magazine.

ruger american rimfire 10/22 rotary magazine convertible stock

Dove-Tailed Action and Bolt with 60° Bolt Throw
Standard 3/8″ dovetails for rimfire rings are milled into the actions, which are also drilled and tapped for mounting Weaver-style bases. The 60-degree bolt can be removed with an easy-to-use, receiver-mounted bolt release that does NOT require a pull of the trigger.

ruger american rimfire 10/22 convertible stock

Integral Bedding Block for Action
The new rimfire rifles also feature a patent-pending Power Bedding® integral bedding block system that positively locates the receiver and free floats the barrel. Additional features include a blued, hammer-forged barrel with fiber optic front sight and adjustable, folding leaf rear sight.

ruger american rimfire 10/22 convertible stock bedding block

New Product Tip from EdLongrange. We welcome reader submissions.
Permalink New Product 1 Comment »
September 1st, 2013

New AR-Platform D-CAT Multi-Tool Performs Variety of Key Tasks

Compared to bolt-action rifles, direct gas impingement AR-platform rifles tend to be filthy, maintenance-intensive beasts, requiring regular disassembly and cleaning of the innards. Op-rod style AR variants run cleaner and cooler, but they still require regular maintenance. Now there is a versatile, compact multi-tool that performs a variety of critical servicing/maintenance tasks for AR-platform rifles.

Brownells D-CAT multi tool

Weighing just 6 ounces, the new D-CAT from Space Age Weaponry fits in the storage compartment of a standard AR-15 fixed butt stock. Brownells says the D-CAT (“Deployable Compact Armorer’s Tool”) is the “only tool necessary to assemble the AR-15/M16 from component parts, or perform a complete disassembly”. The video below explains the feature and functions of the $149.99 D-CAT.

The D-CAT is made from quality materials: 6061-T6 Aircraft Aluminum, 303 Stainless steel, and H13 Tool Steel. Bits, punches, and other small parts are located in the tool magazine, within the torque handle. Simply rotate the magazine gate to expose the individual compartments. Within the magazine you will find a 1/8″ punch, a flat blade driver, front sight adjustment tool, and a 3/16″ and 9/64″ hex driver. There is also a spare punch pocket and a Hammer/Trigger pin pocket. This is also the mode in which the D-CAT is used as a screwdriver. The driver makes use of a standard ¼” hex well so the tool can be augmented to serve as a general purpose driver for any bit you choose to carry.

Tool Tip from EdLongrange. We welcome reader submissions.
Permalink Gunsmithing, New Product 1 Comment »