Keith Glasscock is an outstanding competitive shooter, who has finished second at the F-Class National Championships (F-Open) multiple times. Keith is also a skilled wind coach who runs the popular Winning in the Wind YouTube Channel. Along with his interest in mid-range and long-range F-Class competition, Keith also enjoys game hunting and varmint adventures.
It’s hunting season now, so we showcase two videos Keith has made about developing hand-loads for hunting rifles. Developing accurate hand-loaded ammo for hunting and varmint rifles involves procedures that may be a bit different than load testing for a match rifle. You want to be efficient, and use the types of brass and bullets you’ll be using on the hunts. In two recent videos, Keith shows how he developed good, accurate loads for a .223 Rem varmint rifle and a .308 Win hunting rifle.
.223 Rem Load Development — Powder Charge and Seating Depth
In the first video, Keith covers the load development process for a Remington 700 bolt-action varmint rifle chambered in .223 Remington. Keith starts by full-length sizing the brass. Then he experimented with powder charge weights, and came up with a promising load of 24.7 grains of Alliant AR Comp with Hornady 50gr A-Max bullets.
Next Keith experimented with seating depths (see 5:30-6:100) and found that accuracy improved as he changed OAL length in .005 increments. Keith ended up with 2.270″ with a 3-shot group in the twos! This video shows the importance of testing your bullet choice at various seating depths. Keith shoots this rig prone off bipod, which is similar to the bipod shooting he does in the varmint fields. Keith explains key factors to consider when optimizing the .223 Rem cartridge in a varmint rig. Velocity readings are made with a LabRadar unit.
Load Development for .308 Win Hunting Rifle
In a second video, Keith shows the process for load development with a .308 Winchester hunting rifle. Here Keith uses a large X-type sandbag for a front support. Again, he was shooting a Remington 700 bolt-action rifle, this time with Barnes TSX solid copper bullets, PPU Brass, Federal 210m primers, and AR Comp powder. Keith said the Barnes bullets were excellent — he commented that these bullets were “match quality in terms of precision”. Keith achieved some very small three-shot groups with AR Comp and the TSX projectiles. Keith did note that point-of-impact shifted up significantly with increases in charge weight (see 6:20-7:10). With thinner-contour hunting barrels, this is not unexpected. But POI change should be observed carefully during load development, as you may need to adjust your zero after completing testing.
Three Bonus Videos for Hunters and Huntresses
Here are three videos with useful tips and techniques for hunters and huntresses. These cover rifle marksmanship, optics selection for deer hunting, and efficient methods for sighting-in hunting rifles.
How to Shoot Better with a Hunting Rifle
This “must-watch” video has great practical advice for hunters. It illustrates proper hand-hold and head position, and shows how to stay steady when breaking the shot. Even competition shooters can learn a few things. One viewer notes: “This was very informative. The footage through the scope showing how one’s position moves the sight alignment was particularly helpful.”
You’ll find more great videos on Thomas Haugland’s THLR.NO YouTube Channel, that offers videos for long-range hunters and marksmen. Haugland, who hails from Norway, is a serious shooter, who takes his rifles out into the field, in all conditions. The THLR.NO channel offers solid advice on scopes, reticles, wind-reading, field positions, and much more. Haugland’s team puts a wide variety of gear through serious field tests — every thing from suppressors to packs to electro-optical hardware. In addition the THLR.NO channel provides good advice on stalking techniques and hunting skills.
The Complete Optics Selection for For Deer Hunting
In this video, Vortex optics techs explain the optics package deer hunters will want to take into the field. Along with a good medium-power zoom riflescope, you’ll want binoculars and (probably) a spotting scope. You’ll also want a Laser Rangefinder (LRF) or laser-equipped binoculars. As the team points out, the LRF is not just to range your prey right before you take a shot. A top-quality LRF can range a reflective object as far as 1500 yards away. That helps you decide whether you want to hike a mile to reach that buck you see way out on the next ridge.
How to Sight-In Your Hunting Rifle
This video offers good basic advice for sighting-in a hunting rifle. There are a series of six points covered. Here’s Tip #1: “Find a safe place to shoot your rifle with a backstop. If possible, use a bench and a rock-solid shooting rest. Sighting-in is all about consistency, so the less human error you have, the better. For safety, be sure to also bring ear and eye protection.” READ FULL ARTICLE on NRAWomen.com.
Share the post "Saturday Movies: Load Development for Hunting Rifles & MORE"
For many Americans, real incomes have stayed flat in recent years, while inflation has increased the cost of living very significantly in the past three years. Accordingly, it’s important to save money whenever possible. Prices are going up, but wages aren’t following (for most of us). Here are six ways shooters can save money on gear purchases and other shooting-related expenses.
1. Watch for Our Deals of the Week. Every Monday, in our Daily Bulletin, AccurateShooter.com offers some of the best deals to be found. We search the web to find great deals on ammo, reloading components, optics, tools, firearms, gun safes, electronics and more. It’s not unusual to find savings of 20-35% through our Deals of the Week. And many of our vendors are now offering special deals just for AccurateShooter.com readers.
2. Check Out the Forum Classifieds. There are great deals to be found every day in the AccurateShooter Shooters’ Forum. The latest deals are displayed in the right column of every Forum page. To see all the listings, browse through the Forum MarketPlace section which has four main categories:
Guns, Actions, Stocks, & Barrels
Tools, Dies, Rests, Reloading Components & Misc
Scopes, Optics, Sights, Rings, Bases Etc.
Commercial Sales by Paid Sponsors
3. Share a Ride to Matches. Fuel prices are on the rise — Regular-grade gasoline is over $6.00 per gallon in California now and around $3.85/gallon nationwide. With many shooters living 30-100 miles from the nearest range, fuel remains a big part of a shooter’s hobby budget. We’d say 90% of shooters drive solo to matches, often in large, gas-guzzling trucks. If you drive 200 miles round-trip to attend a match in a 20-mpg vehicle, you’ll burn over $38.50 worth of gasoline on your trip. That adds up. By simply sharing the ride with one fellow shooter you cut your fuel expenditures in half. And, if you alternate vehicles with a buddy from one match to the next, you save on vehicle wear and tear. At $0.55/mile (overall operating costs) consider the savings.
4. Use Discount Codes to Save. It’s always smart to check for discount codes before you buy. In the Daily Bulletin, we feature “Deals of the Week” every Monday morning, and we provide discount Coupon Codes when available. These can reduce the price substantially or lower shipping costs. Search codes for Brownells, Creedmoor Sports, EuroOptic, Graf’s, Midsouth, Powder Valley, Sportsman’s Warehouse, KYGUNCO, MidwayUSA, and Precision Reloading. Check your email also — some discount codes are only announced in email newsletters. If you can’t find a Coupon Code for your preferred vendor, visit Gun.deals and/or RetailMeNot.com. Both those sites list current coupon codes, and RetailMeNot.com covers thousands of vendors.
5. Shop for “Demo” Optics. Modern high-quality optics can easily cost $1500.00 or more, often exceeding the value of the rifle on which they are mounted. However, you can often save 20-30% by purchasing demo optics. These are normally display units used at trade shows. They may have slight ringmarks, but otherwise they are “as new”, having never been carried in the field or used on a rifle that has fired live ammo. When purchasing demo scopes, you should always ask about the warranty before consummating the sale. However, most demo scopes from name-brand manufacturers come with full factory warranties. EuroOptic.com and SWFA.com are two respected vendors that offer a good selection of demo optics.
6. Train with Rimfire Rifles. Good match-grade centerfire, hand-loaded ammo, counting premium bullets, powder, primers, and brass (figuring 10X loads), can now exceed $1.50 per round. And if your $600 (as chambered and fitted) competition barrel is toast after 1500 rounds, add $0.40 for barrel deprecation per shot. So you’re approaching two bucks a round total! By contrast, you can get quite good .22 LR target ammo for under $0.18 per round. Good rimfire barrels last a long, long time, so you don’t have to be concerned about wearing out your barrel quickly. A quality rimfire barrel can retain its accuracy for 7,000 rounds or more. If you run the ballistics, a .22 LR round at 100 yards can emulate the wind drift experienced by a centerfire cartridge at long range. This allows for effective cross-training with much less expensive ammo.
Share the post "Six Ways Shooters Can Save Money This Fall"
CONGRESS MAKES BIPARTISAN REBUKE of PRESIDENT BIDEN’S HUNTER EDUCATION ATTACKS
The National Shooting Sports Foundation (NSSF) praised the U.S. Congress for the swift and decisive vote to rebuke President Joe Biden’s unprecedented move to defund scholastic hunter education and archery programs available for youths. The U.S. House of Representatives approved H.R. 5110, the Protecting Hunting Heritage and Education Act, in a 424-1 vote and the U.S. Senate hot-lined the legislation, passing it by unanimous consent. The legislation, introduced by U.S. Reps. Mark Green (R-TN) and Richard Hudson (R-NC) is now headed to President Biden’s desk for consideration.
The White House has not signaled whether the president will sign or veto the legislation. However, Congress approved the bill in a rare and overwhelming veto-proof majority. Should the president veto the legislation, Congress could override the president’s veto and enact the law.
“This is a tremendous victory for true and proven firearm safety, as well as a reminder of how Congress can unite to protect the American public from special-interest driven agendas,” said Lawrence G. Keane, NSSF Senior Vice President and General Counsel. “This should have never been an issue. Congress never wrote into the Bipartisan Safer Communities Act that hunter education and archery programs were ineligible for funding. That was a unilateral decision to appease gun control and anti-hunting special interests. It was an unforced error that the Biden administration refused to acknowledge. Congress, as the representatives of the people, has spoken and spoken loudly and clearly.”
The Biden administration wrongly claimed the Bipartisan Safer Communities Act (BSCA) forbid the funding of school-based hunter education and archery programs. That was never in the language or intent of the law. Congress appealed to the Biden administration to reverse course in several bipartisan and bicameral letters. Biden could have resolved the issue by simply reversing the policy to deny funds for the essential scholastic programs by ending the policy put into place by Education Secretary Miguel Cardona.
Congress acted when administration officials refused. Congress passed the Protecting Hunting Heritage and Education Act less than two months after it was introduced. NSSF is deeply grateful to Congressmen Green and Hudson for their leadership to restore hunter education and archery funding for schools, as well as for Congress for setting aside partisan politics to represent the interests of all Americans and true and proven firearm safety programs.
Top Photo Courtesy Montana Fish, Wildlife and Parks.
Share the post "Congress Votes to Restore Hunter Education, In Rebuke to Biden"
NRA publication Shooting Sports USA (SSUSA) has thousands of articles online, all free for the reading. Many of these stories have been written by top competitors, including National and Olympic Champions. You will find SSUSA articles spotlighted every week on the NRA Competitive Shooting Facebook page. We recommend you bookmark that page as a valuable resource. Here are four notable SSUSA articles that have been featured on Facebook this month. Go to SSUSA.org to see even more current articles, with new content every day.
Here is an insightful, fairly lengthy 1850-word article about the phenomenon we call mirage. The article explains how and why mirage appears, how it can best be monitored, and how mirage can indicate both wind velocity and direction. Top competitors follow the adage “Mirage is your friend”, because mirage can often be the most important indicator of wind variables — sometimes even more important than wind flags. “The mirage is more sensitive than the flags since it has less inertia and momentum”, wrote Desmond T. Burke, in his book, Canadian Bisley Shooting, an Art and a Science.
Well worth reading, this SSUSA article talks about the properties of mirage. Here is a sample:
“Mirage — can make all the difference between a shot landing squarely in the X-ring or being victimized by an undetected downrange breeze. The true power of mirage is found in its ability to betray the subtlest of breezes downrange. Its fluid movement… can not only provide wind direction, but speed as well.
Typically, the ability to detect mirage is maximized on warm, sunny and sultry days. Expect mirage to be most pronounced in mid-morning or early afternoon, although it ignores these rules with regularity[.]
Mirage is extremely powerful at identifying winds of less than 12 mph, particularly those gentle breezes subtle enough to not even bother moving the flags.
When there is no wind, or a gentle head or tail wind, mirage will appear to be ‘bubbling’ directly up from the ground. Many call this ‘boiling’, and it is probably the easiest of all to detect.
As a general rule of thumb, when wind speed increases, overall height of the waves produced by the mirage is reduced. Large peaks and valleys in the waves mean that particular mirage is being driven by a very slight breeze. Conversely, crest size is reduced with wind speed, making it harder and harder to detect, until the mirage disappears entirely at somewhere around 12 miles per hour. In other words, the taller mirage’s waves appear, the slower the breeze.”
Authored by the late Glen Zediker, this article covers barrel break-in procedures. It is particularly useful for dealing with factory barrels. We CAUTION readers — with outstanding, hand-lapped custom barrels from top barrel-makers, you may want to do very little break-in — clean sparingly and keep barrel heat low. Do NOT use abrasives aggressively. On our Krieger and Brux barrels, we simply wet-patched every 2-3 rounds for 20 rounds and the barrels shot superbly from the start with minimal fouling. But for factory barrels, a moderate break-in process may prove beneficial.
Zediker explains: “Lesser, lower-cost barrels are going to have more pronounced … imperfections within the bore[.] These imperfections are largely tool marks resulting from the drilling and rifling processes. And if it’s a semi-automatic, like an AR-15, there might be a burr where the gas port was drilled. The goal of break-in is to knock down these imperfections, thereby smoothing the interior surface.”
As one who has experienced a cartridge case-head blow-out with a 9mm pistol, this Editor is very conscious of the risks involved and the damage a blow-out can do to the pistol, to the magazine, and (worst of all) to the shooter. Even with new brass, the possibility of a case failure is always present. And even if the case remains intact, we’ve seen primer failures that create a dangerous jet back towards the pistol shooter. That’s why shooters should always employ protective eyewear whenever they shoot.
We love our wheelguns, but there’s no doubt that forcing cone damage can occur, particularly with hot loads and if your cylinder-to-barrel gap is excessive. This article explains how to inspect your revolvers, and how to mitigate the likelihood of forcing cone damage. The article also explains how to clean your revolvers properly. This is very important to avoid build-up of lead and powder residues.
Share the post "Four Articles on Shooting Sports USA Worth Reading"
Gun Owners of America (GOA) and the Gun Owners Foundation (GOF) teamed up with Gun Owners of California (GOC) to file suit challenging portions of SB 2, a bill that anti-gun Governor Gavin Newsom signed into law this week. This unconstitutional legislation was passed in response to the Bruen decision (which ended the state’s draconian “may-issue” policy). As signed by Newsom, California SB 2 will:
— Create vast, restricted “sensitive locations” where concealed carrying would be prohibited, including all private property unless expressly permitted by the owner;
— Require 16 hours of training;
— Significantly increase the costs associated with securing a permit.
This lawsuit challenging SB 2 was filed in the U.S. District Court (Central District South) in Calfornia. The action, entitled May et al v. Bonta specifically goes after the “sensitive locations” provision of the law. Several other anti-gun states have enacted similar unconstitutional legislation in response to the Bruen decision, and GOA and GOF are a part of litigation in several of these cases.
Click image for a list of insurance programs for CCW holders.
Erich Pratt, GOA’s Senior Vice President, issued the following statement:
“This is just the latest assault on our rights in California. Just as concerning, Governor Gavin Newsom has already made his anti-gun intentions quite clear: he wants to effectively repeal the Second Amendment. Sadly, his acknowledgment that doing so would be the only way to enact more gun control did not dissuade him from violating his oath when he signed this law into effect, but we are fully prepared to fight back.”
Sam Paredes, on behalf of the board for GOF and in his role as the Executive Director of Gun Owners of California, added:
“Pro-gun groups in California have had success when pushing back on legislation like this –just look at our victory last week against the state’s magazine ban. And just like in that case, we are confident SB 2 will be overturned. I’ve been warning governors and legislatures across the country since the Bruen decision that these ‘response bills’ will not stand, but unfortunately, many have still been pushed through. That won’t stop us however – states should fall in line, or we will make them.”
Earlier this month, gunmaker GLOCK Inc. presented a $50,000 check to the Civilian Marksmanship Program (CMP) at the CMP Talladega Marksmanship Park in Alabama during the GLOCK Sport Shooting Foundation (GSSF) Annual Match. GLOCK has been a generous sponsor and supporter of the CMP and Talladega Marksmanship Park throughout its existence, dedicating thousands to the organization each year to be used toward programs and initiatives.
GLOCK Inc. V.P. Josh Dorsey and Nat’l Sales Manager Bob Radecki presented the $50,000 check to the CMP’s acting park manager Bret Lankford and Business Development Exec. Stefanie Teaford.
“We’re always so grateful to GSSF and GLOCK, Inc. for supporting the CMP,” said Teaford. “We’ve been able to use their substantial contributions to enhance our impact in the marksmanship community through organized opportunities and through the distribution of fundamental and safety instruction to countless individuals across the country.”
About the CMP’s Talladega Marksmanship Park
Since 2015, Talladega Marksmanship Park, “The Home of Marksmanship,” has been a worthy destination for firearm supporters and guests looking for practice, competition and mindful learning opportunities. Featuring CMP electronic targets and scoring monitors that can only be found at the 500-acre facility, the park regularly hosts rifle, pistol, shotgun and archery events all year long. The CMP’s Unknown Distance Range at Talladega also allows guests to practice their skills in the field of over 100 steel targets, out to 625 yards, and provides even more marksmanship fun at the Park.
The public is welcome, all year long, to test out their firearms or to simply take a tour of the grounds. Off the firing line, the Club House holds a fully stocked Pro Shop that includes an exclusive collection of rifles, ammunition, marksmanship accessories and CMP memorabilia that is always open during park hours. Learn more at the CMP Talladega Park webpage.
The Civilian Marksmanship Program is a federally chartered 501(c)(3) non-profit corporation. It is dedicated to firearm safety and marksmanship training and to the promotion of marksmanship competition. For more information, visit TheCMP.org.
Share the post "GLOCK Donates $50,000 to Civilian Marksmanship Program"
“A bullet launched at a higher altitude is able to fly slightly farther (in the thinner air) for every increment of downward movement. Effectively, the bullet behaves as if it has a higher ballistic coefficient.”
It’s hunting season, and we have a friend who wants to go the high country of Colorado to pursue elk. He recently zeroed his rifle in California, at a range just a few hundred feet Above Mean Sea Level (AMSL). He wondered if the higher altitude in Colorado could alter his ballistics. The answer is a definite yes. However the good news is that free ballistics calculators can help you plot reliable drop charts for various shooting locations, high or low.
The question has been posed: “What effect does altitude have on the flight of a bullet?” The simplistic answer is that, at higher altitudes, the air is thinner (lower density), so there is less drag on the bullet. This means that the amount of bullet drop is less at any given flight distance from the muzzle. Since the force of gravity is essentially constant on the earth’s surface (for practical purposes), the bullet’s downward acceleration doesn’t change, but a bullet launched at a higher altitude is able to fly slightly farther (in the thinner air) for every increment of downward movement. Effectively, at higher altitudes, the bullet behaves as if it has a higher ballistic coefficient.
Forum member Milanuk explains that the key factor is not altitude, but rather air pressure. Milanuk writes:
“In basic terms, as your altitude increases, the density of the air the bullet must travel through decreases, thereby reducing the drag on the bullet. Generally, the higher the altitude, the less the bullet will drop. For example, I shoot at a couple ranges here in the Pacific Northwest. Both are at 1000′ AMSL (Above Mean Sea Level) or less. I’ll need about 29-30 MOA to get from 100 yards to 1000 yards with a Berger 155gr VLD at 2960 fps. By contrast, in Raton, NM, located at 6600′ AMSL, I’ll only need about 24-25 MOA to do the same. That’s a significant difference.
Note that it is the barometric pressure that really matters, not simply the nominal altitude. The barometric pressure will indicate the reduced pressure from a higher altitude, but it will also show you the pressure changes as a front moves in, etc. which can play havoc w/ your calculated come-ups. Most altimeters are simply barometers that read in feet instead of inches of mercury.”
As Milanuk states, it is NOT altitude per se, but the LOCAL barometric pressure (sometimes called “station pressure”) that is key. The two atmospheric conditions that most effect bullet flight are air temperature, and barometric pressure. Normally, humidity has a negligible effect. It’s important to remember that the barometric pressure reported on the radio (or internet) may be stated as a sea level equivalency. So in Denver (at 6,000 feet AMSL), if the local pressure is 24″, the radio will report the barometric pressure to be 30″. If you do high altitude shooting at long range, bring along a Kestrel, or remember to mentally correct the radio station’s pressure, by 1″ per 1,000 feet.
Trajectory of Bullet fired at Sea Level
Trajectory of Bullet fired at 20,000 feet
You can do your own experimental calculations using JBM Online Ballistics (free to use). Here is an extreme example, with two printouts (generated with Point Blank software), one showing bullet trajectory at sea level (0′ altitude) and one at 20,000 feet. For demonstration sake, we assigned a low 0.2 BC to the bullet, with a velocity of 3000 fps.
To learn more about all aspects of Exterior Ballistics, Hornady has a useful discussion of External Ballistics including the effects of altitude and temperature. To dig deeper, Sierra Bullets has a comprehensive Exterior Ballistics Resource Page with multiple sections from the Sierra Manual (4th and 5th Editions), including:
Example from Section 3.0: “When a bullet flies through the air, two types of forces act on the bullet to determine its path (trajectory) through the air. The first is gravitational force; the other is aerodynamics. Several kinds of aerodynamic forces act on a bullet: drag, lift, side forces, Magnus force, spin damping force, pitch damping force, and Magnus cross force. The most important of these aerodynamic forces is drag. All the others are very small in comparison when the bullet is spin-stabilized.”
Share the post "How Altitude Affects Ballistics — Hunters Take Note"
Over 22 million carry permits have been issued in the United States according to a recent study. Overall 8.5% of American adults now have carry permits. Along with CCW permit holders, millions of other gun owners may carry defensive pistols in “open carry” states. Carrying a defensive pistol is a big responsibility. That’s why all those who carry handguns for self-protection should definitely practice regularly. For many, pistol practice is an indoor experience. Indoor ranges are most convenient for those who live near urban centers, where the biggest threats to public safety currently exist. This article covers indoor firearms training and the proper procedures you should follow at indoor ranges.
This Video Covers Basic Gun Range Safety Rules and Etiquette
FIVE IMPORTANT SAFETY PROCEDURES for Indoor Ranges
1. Follow the Three Fundamental Rules for Safe Gun Handling
ALWAYS keep the gun pointed in a safe direction. ALWAYS keep your finger off the trigger until ready to shoot. ALWAYS keep the gun unloaded until ready to use.
2. Follow ALL Range Officer Instructions
ROs are the first and final authority on any range and their decisions are generally final. Arguing with a Range Officer may just get you thrown out.
3. Don’t Bother Others or Touch Their Guns
Respect other shooters’ privacy unless a safety issue arises. Do NOT engage other shooters to correct a perceived safety violation unless absolutely necessary – inform the RO instead. NEVER handle or touch another shooter’s firearm without their permission!
4. Know Your Range’s Rules
Review and understand any and all range rules and requirements/expectations. For example, what is the range’s maximum rate of fire? Are you allowed to collect your brass?
5. Know What To Do During a Cease Fire
IMMEDIATELY set down your firearm, pointed downrange, and STEP AWAY from the shooting booth (or bench). Range Officers do not want shooters trying to “secure/unload” their firearms in a cease fire situation — they want the shooters separated from their guns instantly.
Double-Up on Hearing Protection When Shooting Indoors
Howard Leight states that Impact Pro muffs are “designed for handgun and pistol shooters looking for high NRR … for indoor ranges, covered ranges or other extremely loud shooting environments.”
When shooting indoors we recommend quality muffs with earplugs underneath, offering double protection. When inside an enclosed range, with other shooters blasting away right next to you, you really need effective hearing protection. But you also need to hear range commands and be able to communicate. That’s why we recommend electronic muffs with quality plugs underneath. We recommend the NRR 33 Howard Leight Max-1 Plugs. These tapered plugs are comfortable, easy to insert, and have a flared end for better sound seal.
On top of those plugs, run high-quality muffs. For indoor ranges where sound levels can be extremely high, we recommend Howard Leight Impact Pro Muffs. These offer an impressive 30 dB Noise Reduction Rating (NRR) and the effective noise reduction can be improved by 4 decibels or more by running plugs as well.* These muffs are pretty comfortable and offer Headphone Functionality so you can connect to your smartphone, MP3 player, or other audio device. These muffs are a good value, an Amazon’s Choice for $64.97.
* Four decibels may not sound like much, but remember the decibel measurement system is logarithmic, so four decibels is VERY significant. We have discussed the merits of “doubling up” hearing protection with Ph.D. sound engineers. They told us that a combination of muffs and plugs could reduce effective noise levels by up to five decibels compared to plugs alone. In addition, good muffs will block bone conduction sound energy better than plugs alone.
Share the post "Smart Tips for Handgun Training at Indoor Ranges"
Chris Simmons Wins International Precision Rifle Federation PRS World Championships
Lapua congratulates Team USA’s Chris Simmons on winning the first-ever International Precision Rifle Federation Precision Rimfire World Championships. This highly anticipated match took place August 28 through September 3 at the Piancardato Tiro A Volo range in Collazzone, Italy. Chris was shooting a Vudoo rifle with Lapua X-Act .22 LR rimfire ammunition. Simmons posted an Aggregate score of 165.00 points with a time of 1480.45. The first four finishers were also from the USA. CLICK HERE to see hundreds of photos from the event.
The International Precision Rifle Federation (IPRF) World Championships drew top shooters from 23 nations. The three-day event had competitors tackle a challenging course of fire at different distances, shooting from both supported and unsupported obstacles, with long-range shots, and moving targets, all within tight time constraints.
Simmons, no stranger to the winner’s circle, was part of a two-year selection process to represent the United States at the inaugural IPRF event. Over the past nine months, Simmons took his training to another level, getting up before daylight to hit the range. He also spent many evenings after work shooting 10-12 different positions in a 90-second timeframe, firing hundreds of rounds daily.
Match was conducted in a beautiful hillside location in Collazone, Italy.
After surviving tricky wind conditions and bad wind calls, Simmons found himself in second place prior to going into the last two stages. He then performed great in the final two stages, taking the overall win: “Paul Dallin and I ended up tied and it came down to the fastest aggregate time of all the stages,” commented Simmons. “I won the World Championship by 23 seconds in 2023! Paul is a hell of a shooter and competitors and was tough to beat. Congratulations to him on his second-place finish!”
Top Five Shooters at IPRF Rimfire World Championships:
1. Chris Simmons, USA
2. Paul Dallin, USA
3. Payton Grimes, USA
4. Tyler Orth, USA
5. Radek Novak, Czech Republik
“It was an honor to be able to represent Team USA in the World Precision Rifle Championships in Italy. Thank you to Lapua for supporting both myself and Team USA with quality ammunition,” stated Simmons.
Member of Team USA with a patriotic stars and stripes rimfire rifle.
Competitors came from 23 different countries from around the world.
The USA’s Payton Grimes was top lady shooter and 3rd overall.
The event included unusual stages with across-the-water shots.
Ammo Testing at Lapua Rimfire Performance Centers
The Lapua X-ACT .22 LR ammunition used by Chris Simmons was matched to his VuDoo rifle at a Lapua Rimfire Performance Center in the USA. Unique lots of ammunition are tested at 50 and 100 meters simultaneously, identifying the best performing ammunition for purchase. This service is available to any shooter who wishes to gain a competitive advantage. Schedule your testing at either of Lapua’s Rimfire Performance Centers located in Mesa, Arizona, or Marengo, Ohio.
To learn more about the Lapua Rimfire Performance Centers or to schedule an appointment, visit Rimfiretest.com.
Share the post "USA’s Chris Simmons Wins Rimfire Precision World Championship"
RCBS, a leading manufacturer of reloading equipment and tools, celebrates its 80th anniversary this year, marking eight decades of equipping handloaders with quality, American-made reloading gear. “After 80 years of operation, RCBS is still delivering top quality reloading products backed by world class customer service,” said Justin Smith, product line manager for RCBS. “The brand has never lost the essence that Fred championed back in 1943 and the men and women in Oroville today truly do bleed green. You’ll be hard pressed to find another group who cares more about the quality of products they produce and the consumers who depend on them.”
The RCBS story began in 1943 in the backroom of Fred T. Huntington’s father’s laundry and dry-cleaning business in Oroville, California. A dedicated shooter, Huntington sought to make his own high-quality .22 caliber bullets for shooting local varmints known as rock chucks. He designed and crafted his own “Rock Chuck Bullet Swage” dies, a name later shortened to RCBS.
In the decades following becoming a business, RCBS rapidly grew from a small shop into the nation’s leading maker of reloading equipment. Now using state-of-the-art equipment in large manufacturing facilities, RCBS has stayed near its roots in Oroville.
Product manager and R&D engineer, Steve Koch, has witnessed RCBS’s impressive growth firsthand. He’s been with the company for over 40 years and knows personally how passionate the employees are in Oroville. “Wow, 80 years, a lot has changed. I’m very proud to say that I’ve spent 45 years at this great establishment,” said Koch. “Everyone is extremely proud of what we have here in Oroville. The pride and dedication of the people that produce, assemble and package the finest reloading equipment in the world is the key to our success. Quality is the RCBS motto, and we will continue to ensure we provide our customers with the finest reloading equipment possible.”
In honor of its 80th anniversary, RCBS will soon be introducing a limited-edition Summit single-stage reloading press. This American-made press will feature a special red, white and blue design, and will be limited to only 1,000 pieces. Stay tuned to RCBS social media channels and RCBS.com for more info on this special Summit press release.
To learn more about the RCBS 80th anniversary, check out the video below. For more information on RCBS products and 80-year company history visit RCBS.com.
Share the post "RCBS Celebrates 80th Year in Business — Founded in 1943"
The Magnetospeed V3 chronograph is affordable, easy to transport, and easy to set up. With a MagnetoSpeed barrel-mounted chrono you can quickly and easily record muzzle velocity (MV) without having to set up tripods or walk down-range. The compact MagnetoSpeed chronos are easy to operate and transport. With the full-featured V3 model, everything you need comes in a small fitted case. In the top photo are the components used with the MagnetoSpeed V3 Kit:
1. V3 Bayonet sensor
2. Display and control unit
3. Bayonet spacers (plastic and rubber)
4. Cords and mounting hardware (left), suppressor heat shield (right)
5. Alignment rod (square cross-section)
6. Rail adapter (sold separately)
Our friend Gavin Gear of UltimateReloader.com reviewed the MagnetoSpeed V3 and came away impressed. Gavin explains that a good chrono is essential: “If you want to load and shoot precision ammunition, you need the tools that will produce and validate the precision of your loads. A good chronograph is one of those tools! In this post I’m going to introduce you to the MagnetoSpeed V3 chonograph, the high-end electromagnetic chronograph which fills out the top slot in MagnetoSpeed’s equipment portfolio.”
In this 11-minute video Gavin reviews MagnetoSpeed’s top-of-the-line V3 Chronograph. He shows what ships with the unit, how to set it up for both rifles and pistols, and then he puts it through its paces showing how it captures velocity data. Gavin says he will follow-up with future videos showing how to link the MagnetoSpeed V3 to your mobile phone and how to log velocity data for future reference. To learn more about this high-tech chrono, visit UltimateReloader.com.
Given its compact size, reasonable price, and easy of set-up, we believe all serious shooters should have a MagnetoSpeed in their gear collection even if their primary chronograph is a LabRadar. The MagnetoSpeed V3 complete system is available now for $399.99 from Sportsman’s Warehouse (MSRP is $449.00). A Labadar Chrono by itself is $625.00 but they are currently out-of-stock.
Share the post "MagnetoSpeed V3 Chronograph Review and Field Test"
Starline Brass offers a series of videos with helpful reloading tips. Focused primarily on pistol cartridges, these short videos can help anyone get started with metallic cartridge reloading. If you load pistol rounds on a progressive, this video series is particularly helpful. The on-camera host is Hunter Pilant, son of Carroll Pilant of Sierra Bullets.
Preventing Double Charges
Tip: Use a bulky powder that fills your case more than half way with a correct charge. This will overfill the case if it is double-charged, making it very difficult to seat a bullet.
Tumble New Brass Before Loading the First Time
Tip: Tumble new pistol cartridge brass in used media for 30 minutes before loading for the first time. This will add enough graphite (carbon residue) to smooth case entry into dies. You can also lube the case mouths with graphite, or use spray lube.
Powder Through Expander — How to Eliminate Hang-ups
Tip: When loading pistol brass with a progressive press, sometime the powder-through expander is hard to remove, especially with short cases. There are two fixes — first, try deburring the inside of the case mouth on your cases. Second, the radius of the powder through expander plug can be modified to smooth entry and exit (see photo). Starline will do this modification for free.
Share the post "Pistol Cartridge Reloading — Smart Techniques from Starline"
2. Check Out the Forum Classifieds. There are great deals to be found every day in the AccurateShooter 
3. Share a Ride to Matches. Fuel prices are on the rise — Regular-grade gasoline is over $6.00 per gallon in California now and around $3.85/gallon nationwide. With many shooters living 30-100 miles from the nearest range, fuel remains a big part of a shooter’s hobby budget. We’d say 90% of shooters drive solo to matches, often in large, gas-guzzling trucks. If you drive 200 miles round-trip to attend a match in a 20-mpg vehicle, you’ll burn over $38.50 worth of gasoline on your trip. That adds up. By simply sharing the ride with one fellow shooter you cut your fuel expenditures in half. And, if you alternate vehicles with a buddy from one match to the next, you save on vehicle wear and tear. At $0.55/mile (overall operating costs) consider the savings.
4. Use Discount Codes to Save. It’s always smart to check for discount codes before you buy. In the Daily Bulletin, we feature “Deals of the Week” every Monday morning, and we provide discount Coupon Codes when available. These can reduce the price substantially or lower shipping costs. Search codes for Brownells, Creedmoor Sports, EuroOptic, Graf’s, Midsouth, Powder Valley, Sportsman’s Warehouse, KYGUNCO, MidwayUSA, and Precision Reloading. Check your email also — some discount codes are only announced in email newsletters. If you can’t find a Coupon Code for your preferred vendor, visit 
5. Shop for “Demo” Optics. Modern high-quality optics can easily cost $1500.00 or more, often exceeding the value of the rifle on which they are mounted. However, you can often save 20-30% by purchasing demo optics. These are normally display units used at trade shows. They may have slight ringmarks, but otherwise they are “as new”, having never been carried in the field or used on a rifle that has fired live ammo. When purchasing demo scopes, you should always ask about the warranty before consummating the sale. However, most demo scopes from name-brand manufacturers come with full factory warranties. 
6. Train with Rimfire Rifles. Good match-grade centerfire, hand-loaded ammo, counting premium bullets, powder, primers, and brass (figuring 10X loads), can now exceed $1.50 per round. And if your $600 (as chambered and fitted) competition barrel is toast after 1500 rounds, add $0.40 for barrel deprecation per shot. So you’re approaching two bucks a round total! By contrast, you can get quite good .22 LR target ammo for under $0.18 per round. Good rimfire barrels last a long, long time, so you don’t have to be concerned about wearing out your barrel quickly. A quality rimfire barrel can retain its accuracy for 7,000 rounds or more. If you run the ballistics, a .22 LR round at 100 yards can emulate the wind drift experienced by a centerfire cartridge at long range. This allows for effective cross-training with much less expensive ammo.
Earlier this month, gunmaker GLOCK Inc. presented a $50,000 check to the Civilian Marksmanship Program (CMP) at the CMP Talladega Marksmanship Park in Alabama during the GLOCK Sport Shooting Foundation (GSSF) Annual Match. GLOCK has been a generous sponsor and supporter of the CMP and Talladega Marksmanship Park throughout its existence, dedicating thousands to the organization each year to be used toward programs and initiatives.
The question has been posed: “What effect does altitude have on the flight of a bullet?” The simplistic answer is that, at higher altitudes, the air is thinner (lower density), so there is less drag on the bullet. This means that the amount of bullet drop is less at any given flight distance from the muzzle. Since the force of gravity is essentially constant on the earth’s surface (for practical purposes), the bullet’s downward acceleration doesn’t change, but a bullet launched at a higher altitude is able to fly slightly farther (in the thinner air) for every increment of downward movement. Effectively, at higher altitudes, the bullet behaves as if it has a higher ballistic coefficient.
