Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









June 15th, 2007

How Cartridge Brass is Made

Precision shooters favor premium brass from Lapua, Norma, or RWS. (Lake City also makes quality brass in military calibers.) Premium brass delivers better accuracy, more consistent velocities, and longer life. Shooters understand the importance of good brass, but many of us have no idea how cartridge cases are actually made. Here’s how it’s done.

The process starts with a brass disk stamped from strips of metal. Then, through a series of stages, the brass is extruded or drawn into a cylindrical shape. In the extrusion process the brass is squeezed through a die under tremendous pressure. This is repeated two or three times typically. In the more traditional “draw” process, the case is progressively stretched longer, in 3 to 5 stages, using a series of high-pressure rams forcing the brass into a form die. While extrusion may be more common today, RWS, which makes some of the most uniform brass in the world, still uses the draw process: “It starts with cup drawing after the bands have been punched out. RWS cases are drawn in three ‘stages’ and after each draw they are annealed, pickled, rinsed and subjected to further quality improvement measures. This achieves specific hardening of the brass cases and increases their resistance to extraordinary stresses.”

RWS Brass Cartridge Draw process

After the cases are extruded or drawn to max length, the cases are trimmed and the neck/shoulder are formed. Then the extractor groove (on rimless cases) is formed or machined, and the primer pocket is created in the base. One way to form the primer pocket is to use a hardened steel plug called a “bunter”. In the photos below you see the stages for forming a 20mm cannon case (courtesy OldAmmo.com), along with bunters used for Lake City rifle brass. This illustrates the draw process (as opposed to extrusion). The process of draw-forming rifle brass is that same as for this 20mm shell, just on a smaller scale.

20mm cartridge brass forming

20mm Draw Set Oldammo.com

River Valley Ordnance explains: “When a case is being made, it is drawn to its final draw length, with the diameter being slightly smaller than needed. At this point in its life, the head of the draw is slightly rounded, and there are no provisions for a primer. So the final drawn cases are trimmed to length, then run into the head bunter. A punch, ground to the intended contours for the inside of the case, pushes the draw into a cylindrical die and holds it in place while another punch rams into the case from the other end, mashing the bottom flat. That secondary ram holds the headstamp bunter punch.

Lake City Brass bunter

The headstamp bunter punch has a protrusion on the end to make the primer pocket, and has raised lettering around the face to form the headstamp writing. This is, of course, all a mirror image of the finished case head. Small cases, such as 5.56×45, can be headed with a single strike. Larger cases, like 7.62×51 and 50 BMG, need to be struck once to form a dent for the primer pocket, then a second strike to finish the pocket, flatten the head, and imprint the writing. This second strike works the brass to harden it so it will support the pressure of firing.”

Thanks to Guy Hildebrand, of the Cartridge Collectors’ Exchange, OldAmmo.com, for providing this 20mm Draw Set photo. Bunter photo from River Valley Ordnance, RVOW.com.

Permalink Bullets, Brass, Ammo, Tech Tip 41 Comments »
June 15th, 2007

Father's Day this Sunday, June 17th

Cabela's Father's DayIt’s time to pay our respects to our patriarchs. This Sunday, perhaps take your dad to the range, or spend a day with him doing his favorite activity–whether shooting, golf, fishing, or just firing up the grill in the backyard. If you’re looking for a special gift for Father’s Day, both Cabelas.com and Orvis.com have some excellent promotions running right now.

Father's Day

Permalink News Post comment »
June 14th, 2007

New Stock Design from Baney and Baer

Thanks to sponsors Bruce Baer, Bartlein Barrels and smiths Mark King and Alex Sitman, we are developing a new long-range project gun with two barrels, one chambered in 6mm-6.5×47 and the other in 6.5×47 Lapua. For this project, Jason wanted a hybrid stock that combined features of the popular MBR Tooley-style stock, with an I-beam style fore-end, plus something new and different in the rear.

The new stock, crafted by Bruce Baer, features an I-beam style fore-end with long, straight flats similar to a McMillan Edge™ short-range BR stock. The underside of the fore-end is relieved to allow smoother tracking over a front sand bag. We’ve noticed a trend to wider flats in the back, so we specified a 1.25″ rear flat. We didn’t want to go ultra-wide (2.0″ +) to keep weight manageable and so that a conventional blank (1.5″ wide at comb) could be used. We were also concerned about friction and bag-handling if the flat was too wide. To lessen drag and improve tracking, Jason told Bruce to cut a relieved area, or “channel” in the underside of the toe. The idea here was to reduce friction and to provide improved contact with the ears of the rear bag. With a very wide flat, there is a tendency to ride on the stitching between the ears. With this design, we hope, the left and right edges of the rear flats will engage the ears.

Permalink Tech Tip Post comment »
June 14th, 2007

Great Deal on Sierra Varmint Bullets

Jeff Bartlett of GIBrass.com has some great prices on new Sierra production 55gr varmint bullets, .224 diameter. Two varieties are offered:

55gr BlitzKing with cannelure. Sierra item #9373.
Prices: $12/100; $55/500; $100 per thousand

55gr Varminter Soft Point. Sierra item #1360.
Prices: $12/100; $55/500; $100 per thousand.

Bartlett’s special production BlitzKings have cannelures, making them better for reloaders who prefer to crimp their ammo. Regular production Sierra 55gr BlitzKings (Sierra #1455) have no cannelure and typically sell for $16/box. Jeff also reports that he has plenty of the ultra-accurate ‘Euro’ 4895 powder, highly recommended by G. Salazar of ShootersJournal.com. This burns slightly slower than IMR 4895, closer to IMR 4064. It works great in the 6mmBR and .308 Win. Price is $100 per 8-lb jug.

Permalink Bullets, Brass, Ammo, Hot Deals Post comment »
June 13th, 2007

Recoil–Can it Be a Good Thing?

Over the past decade and a half we’ve seen a definite trend to smaller calibers in both Highpower and long-range benchrest competition. Smaller projectiles have allowed a whole new style of bench-shooting, where you don’t have to hold the rifle at all. In the Service Rifle discipline, the .223 “Mouse Guns” changed the sport forever. Many would say this “downsizing” is all for the good. But have we lost something in the process? In engineering away recoil, have we “neutered” the sport and made it less exciting?

Here’s what the legendary Col. Jeff Cooper had to say:

“Do you enjoy recoil? A recent article in Magnum magazine from South Africa points out that the retroactive shock delivered by the shooting of a firearm is not necessarily punishment. The sock you feel when your racket centers a tennis ball, or when you floor the throttle on a highly-bred car in third gear, or when you hit the water from the boat deck of your fishing cruiser–these things are exhilarating. It seems possible that this tendency to mitigate the shock of recoil maybe overlooking something. Personally I enjoy shooting a full-sized weapon more than I do a 22, and if I can remember that far back, I used to anticipate with distinct pleasure an unavoidable tackle when running back a kickoff. Perhaps we should think further upon this.” — Jeff Cooper Commentary

Is the Colonel right? Is recoil part of the fun of the sport, like the heeling force of a sailboat when it catches a puff of wind? Have we gone too far in reducing recoil in our “full-bore” match calibers? Has shooting become a sport for wimps?

What are your views?
To comment, click the “comments” link below.

Permalink News 5 Comments »
June 13th, 2007

Sightron 6-24×50 Scope for $479.99

sightron 6-24x50 scopeGrafs.com is offering huge savings on the Sightron SIII SS, 6-24×50 side-focus scope. Having made a special buy of this quality optic, item SIIISS624X50, Grafs.com is selling it at just $479.99 while supplies last. That’s $150.00 to $200.00 less than other optics vendors are charging. This scope features a “satin black” finish, plex reticle, 1/4-MOA clicks, tall “target-style” turrets, and a side parallax adjustment. If you contact Graf & Sons, be sure to tell them you heard about this deal on AccurateShooter.com. Note: no further discounts available. $479.99 price limited to supplies on hand. Click HERE for scope specifications.

sightron SIII SS 6-24x50

Permalink Hot Deals, Optics Post comment »
June 12th, 2007

Berger 108gr Shines in Early Testing

Berger Bullets has issued three new prototype non-VLD 6mm bullets for testing, in 105, 107, and 108 grain weights. Initial results are promising to say the least, particularly with the 108s. Here’s a photo of all three by Wm. Roscoe.

Berger bullets 6mm

Danny Reever reports: “Here’s the best group I shot today with the Prototype Berger 108 grain BT at 500 meters (547 yards). The group measured a fantastic .870 inch! The worst group I shot today with the same bullet measured 1.752 inch which is none too shabby either.”

Danny adds: “I do think this new bullet is a winner. All the bullets shot well for me, but the 108 was hands down the best performer. I had the chance to test the new lot #591 105gr VLD since Eric polished the die out and it shot very well also. Best group being a 1.544″ @ 500 meters which was shot in a 5-15 MPH wind. I’m now anxious to find out which bullet they will select for production. If it’s the 108 I’m going to order 3000 right from the get-go. That’s how impressed I am with that bullet!” Danny’s load was Berger 108, .015″ into the lands, neck-turned Lapua 6mmBR brass, CCI450 primer, 30.5 grains of Varget (the usual disclaimer applies here).

Bob Woodward (Matsubob) agrees: “Here is a group I shot with a 6mm Grendel on an AR15 space gun at 200 meters (8-twist Whitley upper). Very good group for an over-the-course national match rifle.”

What’s the secret to the accuracy of the 108s? It looks like Berger is pointing up nice, consistent meplats. But it appears the 108 has a shorter boat-tail than the 105 or 107 prototype. We should add that the 107s are shooting well too. William Roscoe got promising results with the 107s. Holding dead center (no wind correction), five of the new 107s went into .614″ vertical at 330 yards. More Details.

Permalink Bullets, Brass, Ammo Post comment »
June 12th, 2007

Phillips' World Record Rifle for Sale

Sadly, James Phillips (JamesinTN) has decided to get out of competitive long-range benchrest shooting. He’s told us that travel costs (gas/motel) have just gotten too high, and the process has become too much work, and too little fun. James’ decision means that you can purchase a world-record rifle for a bargain price. James actually has three rifles for sale. You can see them all in this Forum Classified Listing.

Rifle 1 — 22 Dasher & 6 Dasher–World Record Gun
This rifle earned James 3 World Records and is capable of earning more. Rem 40X action, Shehane stock, Jewell trigger. Mulitple barrels come with the gun: Hart 8-Twist 22 Dasher (world record barrel); Hart 8-Twist chambered in 22 Dasher, less than 200 rounds; Krieger 7.5-Twist chambered in 6 Dasher (for Tubb 115s) less than 300 rounds; Krieger 8.5-Twist chambered in 6 Dasher less than 400 rounds; 9-Twist Chambered in 6 Dasher for 108 BIBs less than 200 rounds. The bolt has had the firing pin turned and bushed. There is also a brand new, spare bolt with magnum bolt face. Total of FIVE (5) barrels chambered for this action. Price is $3000.00 (without scope) plus shipping. Add $1000.00 for the NightForce 8-32x Benchrest Scope and rings.

Rifle 2 — 7500 Lawton Dasher/6mmBR
Next is a nearly brand new Lawton 7500 dual port (Jewell trigger) with RBLP right eject, SS action for Dasher case, in a Shehane stock. One-piece, +15 MOA base. Three barrels come with the rifle: 1) Krieger 8.5-Twist, chambered in 6 Dasher (.268), less than 200 rounds; 2) Hart 8-Twist 6mmBR rechambered from a 6 Dasher, less than 500 rounds and has a brake; 3) Hart 1.250 dia. 6mm 12-Twist–brand new, unfired, unchambered. 6mm Dasher brass comes with this rifle but no reloading dies as they will be going with the 40x. Price is 3000.00 w/o scope or 4000.00 with NF 8-32BR and rings

Rifle 3 — .243 AI, 22 Dasher
The third rifle is a Winchester SA Trued by Dave Tooley, with a bushed firing pin. Shehane stock bedded by Mike Bryant, Jewell Trigger. It comes with two barrels (.243 AI, 22 Dasher) both with less than 500 rounds and brass. The .243 AI comes with Redding Comp series dies and a Tooley FL neck die. Price is 1600.00 w/o scope or 2600.00 with Nighforce 12-42x BR scope and rings.

NOTE: James will NOT sell the scopes separately until the rifles are sold.

Permalink Hot Deals, News 5 Comments »
June 11th, 2007

Aotearoa Air Safari (New Zealand)

Here’s a report from Mike in NZ about his recent deer-hunting trip: “Under the shadow of the Matemateaonga Range in the central North Island of New Zealand there is a magical piece of land. Initially broken in out of native bush in the early 1900’s, it was left to revert during the 1930’s before being partially developed again during the late 1940’s. Now it is run as a hunting block catering for local and overseas hunters.


“Aotearoa”, meaning “long, white cloud”, is the native Maori word for New Zealand.

The country is a rolling contour, and is a mixture of rough pasture, scrubby gullies and native bush. It bounds onto the Wanganui Forest Park, which is thousands of acres of dense bush. The only access is by jet boat up the Whanganui river, or by air. (There’s a flattish piece of land on the property that is quaintly referred to as an ‘airstrip’.)

Large Photos: NZ Mist | Aerial | Morning Light | Taking Off

The area is a hunting paradise containing good numbers of free range red deer, fallow deer, wild pigs and goats. It is run as a privately-owned hunting block. I have been fortunate enough to be able to hunt there over the past six years, and have just come back from a typical meat-hunting trip.

There were six of us (Mike, Mike, Chris, Al, Colin and Jeff), and the idea was to take a couple of meat animals each. Transport was by air (Cessna 206). This is a six-seater (including the pilot), so we elected to do two trips. The first trip caried five of us plus the pilot and a bit of gear. For the second trip the back four seats are removed allowing plenty of room to take lots of gear in, and (more importantly) plenty of room to (hopefully) take meat out at the end of the trip. Beats walking….

Hardware consisted of one Tikka T3 in .223 Rem with a Leupold 3-9 variable, one Rem Model 7 in 7-08 with a similar scope, one Sako Finnbear in .270 Win with a Redfield vari, one .223 Rem Zastava with a cheapo scope, and two scoped No. 4 Enfields in .303 British.

After a 15-minute flight, we made a couple of low passes over the ‘airstrip’ to make sure that everything looked OK (well, as good as it was going to get anyway), and then touched down. There were no baggage handlers or airline hostesses to greet us, so we carried our gear up to the lodge, had a bit of lunch and got organised for an evening hunt.

I headed down to some grass and scrub river terraces that are normally pretty productive. The wind was in my favor, and I opted to drop down to the terraces through the scrub rather than take the track down as that would mean that there would be less chance of being seen from the bottom. I was doing a slow sneak around the bush edge when a red hind appeared grazing around the edge of a finger of scrub at about 100 yards. I slowly sunk down and did a quick little crawl to a handy little rise to use for a rest. As I eased the rifle up onto the rise the deer saw the movement and was instantly on alert.

I was considering a neck shot, but as the deer was on the verge of doing a runner, I played it safe and put the crosshairs straight up the front leg and a bit under half way down. Allowing for the fact that she was slightly facing towards me, I squeezed the trigger, the .223 cracked and the deer trotted about 10 yards and piled up.” Here she is, a New Zealand Red Hind:

There’s more to this story (this was just the first part), and we may have Mike write full a feature story later this year.
© copyright 2007 Michael Falconer, All Rights Reserved.

Permalink - Articles, News Post comment »
June 10th, 2007

Indiana's Steel Target "Disneyland"

Many of our readers tell us: “I love the challenge of shooting paper in Benchrest, F-Class, or Highpower matches, but it would be fun to get some buddies together and ring some steel at multiple distances.” Well, if you’re in America’s heartland, here’s a place to go. Young’s Longshot Range, in Woodruff, Indiana, is a veritable “Disneyland of Steel”, with a huge variety of reactive metal targets set at yardage-marked berms from 25 to 1000 yards. Indiana’s only 1000-yard facility, Young’s Longshot Range is open 365 days a year. It has outdoor shooting stations (both covered and uncovered), PLUS a heated building with drop-down windows for winter shooting. There’s even a raised 5 meter high platform for prone shooting.

Youngs LongShot Range LLC

Youngs LongShot Range LLC

Youngs LongShot Range LLC

Larger Photos: Range | View from Bench | Shoot House | Shoot House Interior | 600-yd Swinger Target Bay

Youngs Longshot Range 700 yards

Click HERE for a nice story with full-size photos showing the range and target bays. Big thanks to Michael Sorensen (above) for that story and the larger range photos.

Permalink News Post comment »