The anvil is the tripod-shaped thin metal piece protruding above the bottom of the primer cup. Getting the primer sitting fully flush on the bottom of the case primer pocket, without crunching it too much, requires some keen feel for the progress of primer seating.
In two recent Midsouth Blog articles, Glen Zediker offers helpful advice on priming. First he examines what happens to the primer itself as it is seated in the cup. Glen explains why some “crush” is important, and why you never want to leave a high primer. Glen also reviews a variety of priming tools, including his favorite — the Forster Co-Ax Bench Primer Seater. Then he offers some key safety tips. Glen provides some “rock-solid” advice about the priming operation. You’ll find more great reloading tips in Glen’s newest book, Top-Grade Ammo, which we recommend.
Priming Precision vs. Speed
Glen writes: “The better priming tools have less leverage. That is so we can feel the progress of that relatively very small span of depth between start and finish. There is also a balance between precision and speed in tool choices, as there so often is.”
Benchtop Priming Tools — The Forster Co-Ax
Glen thinks that the best choice among priming options, considering both “feel” and productivity, may be the benchtop stand-alone priming stations: “They are faster than hand tools, and can be had with more or less leverage engineered into them. I like the one shown below the best because its feeding is reliable and its feel is more than good enough to do a ‘perfect’ primer seat. It’s the best balance I’ve found between speed and precision.”
Load Tuning and Primers
Glen cautions that you should always reduce your load when you switch to a new, not-yet-tested primer type: “The primer is, in my experience, the greatest variable that can change the performance of a load combination, which is mostly to say ‘pressure’. Never (never ever) switch primer brands without backing off the propellant charge and proving to yourself how far to take it back up, or to even back it off more. I back off one full grain of propellant [when I] try a different primer brand.”
Priming Safety Tips by Zediker
1. Get a good primer “flip” tray for use in filling the feeding magazine tubes associated with some systems. Make double-damn sure each primer is fed right side up (or down, depending on your perspective). A common cause of unintentional detonation is attempting to overfill a stuffed feeding tube magazine, so count and watch your progress.
2. Don’t attempt to seat a high primer more deeply on a finished round. The pressure needed to overcome the inertia to re-initiate movement may be enough to detonate it.
3. Don’t punch out a live primer! That can result in an impressive fright. To kill a primer, squirt or spray a little light oil into its open end. That renders the compound inert.
4. Keep the priming tool cup clean. That’s the little piece that the primer sits down into. Any little shard of brass can become a firing pin! It’s happened!
Here’s a smart new product from Midsouth Shooters Supply: 250 self-adhesive Benchrest Targets on a convenient roll. Not just for benchrest competitors, these stick-on targets work great for anyone doing load development. Each target offers a precision 1/4″ grid at the top with diamond aiming box below. This is similar to official targets used in Benechrest matches, with the addition of the upper grid lines which allow you to instantly estimate group size. These targets also include an area to list your load components. Midsouth sells the 250-target roll for $14.98.
This target was designed for benchrest shooting, developing new loads or cataloging existing ones. This easy-to-use target has a 1/4″ grid pattern at the top which helps measure groups. The vertical aiming square at the bottom helps align the cross hairs of your scope for consistent shot placement. At the very bottom of the target there is room to record your reloading information. Each Target sticker measures 6″ x 4″ with a 4.5″ x 2.5″ printed area.
Take a look at that group. That would be pretty nice for 200 yards. But this group was shot at 600 yards in competition by Fred Dobson at a recent NBRSA match in Oregon. The X-Ring is 1.2″ in diameter. Perfectly centered for a 50-5X, this Light Gun target should be a new NBRSA Score record, pending approval. The previous Score record was Ken Schroeder’s 50-4X.
Fred’s 600-yard group is also amazingly small. Using On-Target Software, we measured Fred’s five-shot group at 0.738″, which is a tiny 0.118 MOA at 600 yards.
NOTE: This is NOT an official measurement. The actual 5-shot group size might be larger or smaller, though it won’t be an NBRSA GROUP record. The current NBRSA 600-yard Light Gun group size record is 0.5823″ set by Robert Hoppe way back in 2008. But Fred’s 50-5X target should, indeed, be a new SCORE record.
Forum member “Jet” reports: “The Tri-County Gun Club just south of Portland, Oregon hosted its second NBRSA 600-guard match 11/18/2017. Twenty-one shooters brought rifles to the line. Fred Dobson shot the 50-5X target shown here.”
Congrats to Fred. Forum member KVD posted: “That’s truly fine shooting — something to be proud of. Seems like the bar gets boosted higher and higher every time there is a sanctioned match.”
Load Specifications
Cartridge: 6mm Dasher
Bullet: Precision Ballistics 105 gr
Powder: Hodgdon Varget
Primer: CCI 450
TCGC 600-yard Range. This range uses the same target holders as the 300-yard line of the 200–300 yard range, which is closed when the 600-yard range is in use. Raised platform is for prone shooting.
About the Tri-County Gun Club in Oregon
Tri-County Gun Club is one of the premiere shooting clubs in the Pacific Northwest. The 230-acre private facility is located in Sherwood, Oregon just 15 minutes from downtown Portland. TCGC offers a wealth of ranges, competitions, and social activities for shooters of all ages, interests, and skill levels.
Article Tip from Boyd Allen. We welcome reader submissions.
We like “outside of the box” thinking. And in the world of competitive shooting, it doesn’t get more unconventional than this. But this radical liquid-cooled benchrest rig wasn’t just a crazy experiment — it actually delivered the goods. This IBS Heavy Gun, built by Joel Pendergraft, produced a superb 10-shot, 3.044″ group that stood as an International Benchrest Shooters (IBS) 1000-Yard Heavy Gun record for seven years, not being broken until 2016*.
Using this water-cooled 300 Ackley Improved, Joel shot the record-breaking group in April 2009 at Hawks Ridge, NC. This monster features a 12-twist, 4-groove Krieger barrel inside a water-filled sleeve (like on a liquid-cooled machine gun). Joel shot BIB 187gr flat-based bullets in Norma brass, pushed by a “generous amount” of Alliant Reloder 25 and Federal 210M primers.
This 3.044″ 10-shot group was a remarkable accomplishment, breaking one of the longest-standing, 1000-yard World Records.
Pendergraft was modest after his notable achievement: “What makes this so very special is to be able to celebrate the accomplishment with all of my shooting friends[.] A good friend once said that records are shot when preparation and opportunity meet. I feel blessed to have personally had the opportunity. The preparation we can individually work on and achieve but the opportunity only comes to a few. Those of you that compete in long range competition will know what I mean.”
*On July 24, 2016, Michael Gaizauskas shot a 2.871″ ten-shot group that bettered Pendergraft’s record by 0.171″ (less than a quarter inch). Michael’s group was also all in the 10 ring, for a perfect 100 score. CLICK HERE for IBS Long-Range Records
Airport photo by Politikaner under Creative Commons License.
Thanksgiving is almost here. We know many readers will soon be traveling to spend the holiday with family members. If you will be flying with firearms this November, you should read this article. You need to familiarize yourself with current Federal Regulations on gun transport before you get anywhere near an airport. Thankfully, the Transportation Security Administration (TSA) has a web page that states the important requirements for airline passengers traveling with firearms* and/or ammunition.
You’ll want to visit the TSA Firearms and Ammunition webpage, and read it carefully. In addition, before your trip, check the regulations of the airline(s) with which you will fly. Some airlines have special requirements, such as weight restrictions.
Here are the TSA’s key guidelines for travel with firearms:
More Airline Travel Tips from Tom McHale
Tom McHale has written an excellent article for the Beretta Blog, Ten Things You Need to Know about Flying with Guns. We suggest you visit the Beretta Blog to read this informative story. Here are two of Tom McHale’s Travel Tips:
Weigh your gun case and ammunition
Most airlines will allow up to 11 pounds of ammunition. And, like any luggage, you will be charged more for any baggage weighing more than 50 pounds. This sounds like a lot, but when traveling to the Crimson Trace Midnight 3 Gun competition last year, my case with shotgun, rifle, pistol and ammunition tipped the scale past the 50 pound mark.
Pack ammo in the same locking case
This is another area that’s misunderstood and full of internet myth. Your ammo just needs to be stored in some type of safe container and not loose. Technically, you can keep ammunition in magazines, but I wouldn’t recommend it. It meets the letter of the law storage requirement, but too many airline and TSA agents will give you grief. Use a plastic ammo box or original cardboard packaging and you’ll be fine carrying that in the same lockable case as your gun.
*SEE United States Code, Title 18, Part 1, Chapter 44. A “firearm” is defined as: any weapon (including a starter gun) which will, or is designed to, or may readily be converted to expel a projectile by the action of an explosive; the frame or receiver of any such weapon; any firearm muffler or firearm silencer; and any destructive device. As defined by 49 CFR 1540.5 a loaded firearm has a live round of ammunition, or any component thereof, in the chamber or cylinder or in a magazine inserted in the firearm.
Looking for culinary inspiration for your holiday gatherings? The NRA Blog offers three special (and delicious) Wild Game Recipes for your family feasts: Honey Mustard Planked Wild Turkey Breast, Mushroom-Stuffed Wild Boar Roast with Black Truffle Sauce, and BBQ Brined Pigeon. These recipes come from some of the country’s best chefs, and they all seem mouth-watering. You’ll find a full list of ingredients plus step-by-step cooking tips.
One of the many advantages to hunting is the assortment of game you can gather that lasts for an extended period of time. Just because it’s Thanksgiving doesn’t mean you have to stick with a whole turkey from the store and a ham hock.
We have three unique spins on wild game recipes that will suit your dining table perfectly. Even if you’re one of those hunters who enjoys a quick hunt the morning of Thanksgiving, these recipes will make your holiday more delicious than ever. — NRABlog.com
Sierra Bullets has just released load data for the 6.5 Grendel, a popular cartridge that works equally well in bolt guns and AR15-platform gas guns. Sierra published comprehensive 6.5 Grendel load data, covering 19 powders and eight (8) different bullets from 85 to 130 grains. NOTE: Hornady-brand brass (see below) was used for Sierra’s 6.5 Grendel tests, not the stronger Lapua 6.5 Grendel brass. Hand-loaders using Lapua 6.5 Grendel brass may need to adjust their loads. Also Winchester WSR primers were used. We imagine most precision hand-loaders will prefer CCI or Federal primers.
Sierra Bullets Tested for 6.5 Grendel Load Data
85gr HP (#1700)
100gr HP (#1710)
107gr HPBT (#1715)
In developing its 6.5 Grendel load data, Sierra tested a very wide selection of propellants, 19 in all. For the 85gr to 100gr varmint bullets, modern powders such as XMR 2230, Power Pro Varmint, and Ramshot TAC offered the best velocity in the 24″ test barrel. For the heavier 120gr to 130gr match bullets, Sierra tested a selection of powders. Highest velocities came with Power Pro Varmint and TAC. If you’re looking for best accuracy, consider the slower burn-rate powders such as IMR 8208 XBR and Varget — but you’ll sacrifice some speed. Overall, Sierra’s latest 6.5 Grendel load data is an excellent addition to the 6.5 Grendel knowledge base. Thanks Sierra!
Here are Sierra’s 6.5 Grendel Load Data Charts for Sierra’s 123gr HPBT, 130gr HPBT, and 130gr TMK. There are a five other tables for lighter-weight Sierra bullets.
History of the 6.5 Grendel Cartridge
The 6.5 Grendel originated as a 6mm PPC necked up to 6.5 mm. After Alexander Arms relinquished the “6.5 Grendel” Trademark, the 6.5 Grendel was standardized as an official SAAMI cartridge. It has become popular with target shooters and hunters alike because it is accurate, efficient, and offers modest recoil. Good for small to medium game, the 6.5 Grendel is becoming a popular chambering in lightweight hunting rifles, such as the Howa Mini Action Model. It is one of the most accurate cartridges you can shoot in the AR-15 platform.
The high-tech orange LabRadar represents the state-of-the-art in personal chronographs. It is extremely accurate, versatile, and you don’t need to go down-range to set it up. Some shooters have even used one during a benchrest shooting match (see below). LabRadars are used by many top shooting champions and the LabRadar chronograph has earned very positive reviews from respected testers such as Ray Gross, USA F-TR Team Captain.
Lab-Radar Discounted for First-Time Ever — Save $60.00
Since its introduction a couple years ago, the LabRadar has been in high demand. And the manufacturer has enforced a “no-discount” policy. Now, for the first-time ever, you can get a LabRadar unit for a reduced price: $499.95. This reduced price, $60 off normal retail, is available now through December 3, 2017. Many vendors are offering the LabRadar at this discounted price including Bruno Shooters Supply, MidwayUSA, and TCK LLC. Other vendors Applied Ballistics and Midsouth don’t show the discount yet, but you can call and ask.
New High-Quality Portable Base for LabRadar Chronograph
If you currently own a LabRadar, or plan to buy one soon, there’s a smart new accessory you should consider buying. Matt Owens, one of our Forum members, has created a new, compact base for the LabRadar that works better than the flat, orange baseplate offered by the manufacturer.
Matt, aka “Arkcomatt”, explains: “These are machined from aluminum and put together with stainless steel screws. The rubber feet are held on with screws also. No more coming off. The legs have nylon washers between them and the base for smooth operation. The screws are torqued and thread locker applied. One of the best things is, with the standard attachment, it will fit in the case with the unit. No more having to take apart! Just fold the legs. It takes up less room on the bench and allows you to get it closer to the rifle. It is very stable and holds up very well in high winds.” ORDER BASE HERE.
This folding base unit costs $75.00 + $7.50 for shipping (USPS). In addition, Arkcomatt now offers a swivel (ball) mount and stainless spike feet (for ground use). The swivel unit costs $10 and spikes are $20 per set. The 1.4″-long spikes screw in the sames holes as the rubber feet.
Forum Member Praise Arkcomatt’s LabRadar Folding Base:
You can read user reviews of the Matt’s LabRadar base in this Forum Thread.
Bullet-maker Bart Sauter has one of these bases now and he endorses it: “These bases are great for the LabRadar. Stable and compact — completely grab and go!”
Forum member Peterson1 agrees: “This is more stable than the Labradar base for my use–off a concrete BR bench, yet takes up less space. Also easier/quicker to set unit up and aimed at target. Never take the unit off for transport in LabRadar case. Only negative — you can’t trade in the factory LabRadar base toward purchase of this base. So buy smart the first time!”
Forum Member SkiUtah02 uses the base with optional spiked feet: “Met up with Matt at the Sierra Cup and bought my base with … spikes for the feet to put into the ground. Just had a chance to test it today and it worked great. I removed the rubber feet, and screwed in the four spiked feet, added a threaded-rod-coupling nut onto the bolt so that I could mount an old photography lighting stand swivel head to the base! Worked perfectly. Thanks Matt!”
Need to find an FFL near you (or near a destination to which you’ll be traveling)? Then check out this handy FFL Finder App from Huntgeek.com. This easy-to-use, inexpensive Mobile App locates FFLs throughout the country. FFL Finder sells for 99 cents ($0.99) for Apple iOS or Android OS.
This App helps sellers as well as buyers. When you sell a firearm to a resident of another State, Federal law requires the shipment to be received and logged by an FFL. This App helps you quickly identify a reputable FFL near your purchaser. It can also help you identify a gunsmith FFL if you are away from home on a hunting trip: “Great app to find gun shops when you travel outside your home area.”
With FFL Finder, you instantly get mapped results of FFL holders near your location (via GPS) or by selecting an area on a map. You can quickly find a variety of nearby FFLs you can contact to compare their transfer rates and policies. If you need to ship a gun out of state, the program quickly finds an FFL who can receive the firearm. And if you are traveling away from home for a match, or a hunting trip, the App can find locations where you can obtain ammo, supplies, and replacement parts. That’s reassuring. Imagine you are traveling and your firearm breaks, or your optics fail, so you need spare parts or a new scope immediately. The FFL Finder App can help you source what you need.
For some applications, we prefer a non-bushing FL die over a bushing die. Shown here are three Forster full-length sizing dies, with necks honed to three different dimensions: 0.265″, 0.266″, and 0.267″.
The Honed Full-Length Sizing Die Option
There are many good options in full-length (FL) sizing dies. Most precision hand-loaders prefer FL dies with neck bushings. These let you adjust the “grip” on your bullet by using larger or smaller bushings. FL bushing dies are available from Whidden Gunworks, Forster, Redding and other makers.
Conventional, non-bushing full-length sizing dies can create ultra-accurate ammo with very low run-out. But many conventional non-bushing FL dies have an undersized neck diameter so you end up with excess neck tension, and you work the brass excessively.
There is another effective option, one that promises extremely low run-out. The honed FL die is a full-length sizing die that has the necked honed to provide a precise fit to the case-neck. When done right, honed FL dies produce extremely straight ammo — as there are no issues with bushing alignment (or bushings that are not perfectly concentric). This Editor owns honed dies from Forster, Redding, and Whidden. They all perform extremely well, delivering match ammunition with extremely low run-out measured with a 21st Century Concentricity Gauge.
In one of the most popular articles we’ve ever published, Bugholes from Bipod, California shooter “Froggy” explained why he prefers honed dies for his tactical ammo.
Q: Do you FL size every time? Do you use custom dies?
Absolutely, I full length resize all of my brass every time I reload. And guess what? I’ve never had a feeding problem.
I do use a modified sizing die, without bushings. My FL resizing die has been custom-honed in the neck area to give .0015″ press fit on the bullet. I also put a slightly larger radius at the neck shoulder junction. I feel that this helps to seal the chamber. With this die, I get consistent neck tension every time–without bushings. Bushings are useful when you’re fishing around for a good load. But once you find the right amount of sizing for ideal neck tension, you can do this better with a customized FL die.
6.5 Guys Review Forster Honed Full-length Dies
The 6.5 Guys recently reviewed honed FL sizing dies from Forster, explaining the pros and cons of this type of reloading die. They explained that, if you load a wide variety of bullets from different manufacturers, you many want to stick with a Bushing FL die. However, if you have settled on a particular bullet and found the “ideal” neck tension, then a honed die may make sense.
In this Gear Update, the 6.5 Guys discuss a service offered by Forster Products to custom hone the neck diameter of its full-length sizing dies to the customer’s specifications (to the thousandth). Whidden Gunworks also offers custom-honed FL dies.
In two recent Midsouth Blog articles, Glen Zediker offers helpful advice on priming. First he examines what happens to the primer itself as it is seated in the cup. Glen explains why some “crush” is important, and why you never want to leave a high primer. Glen also reviews a variety of priming tools, including his favorite — the Forster Co-Ax Bench Primer Seater. Then he offers some key safety tips. Glen provides some “rock-solid” advice about the priming operation. You’ll find more great reloading tips in Glen’s newest book, Top-Grade Ammo, which we recommend.
Fred’s 600-yard group is also amazingly small. Using 
